| Age | Commit message (Collapse) | Author |
|---|
|
There is no functional change in this patch, it only prepares the next one.
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace gpiod_set_value() with gpiod_set_value_cansleep(), as the switch
reset GPIO can be connected to e.g. I2C GPIO expander and it is perfectly
fine for the kernel to sleep for a bit in ksz_switch_register().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In configuration of vlan over bridge over aquantia device
it was found that vlan tagged traffic is dropped on chip.
The reason is that bridge device enables promisc mode,
but in atlantic chip vlan filters will still apply.
So we have to corellate promisc settings with vlan configuration.
The solution is to track in a separate state variable the
need of vlan forced promisc. And also consider generic
promisc configuration when doing vlan filter config.
Fixes: 7975d2aff5af ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should rather have vlan_tci filled all the way down
to the transmitting netdevice and let it do the hw/sw
vlan implementation.
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We build vlan on top of bonding interface, which vlan offload
is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is
BOND_XMIT_POLICY_ENCAP34.
Because vlan tx offload is off, vlan tci is cleared and skb push
the vlan header in validate_xmit_vlan() while sending from vlan
devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to
get information from protocol headers encapsulated within vlan,
because 'nhoff' is points to IP header, so bond hashing is based
on layer 2 info, which fails to distribute packets across slaves.
This patch always enable bonding's vlan tx offload, pass the vlan
packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Fixes: 278339a42a1b ("bonding: propogate vlan_features to bonding master")
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before suspending, mtk-eint would set the interrupt mask to the
one in wake_mask. However, some of these interrupts may not have a
corresponding interrupt handler, or the interrupt may be disabled.
On resume, the eint irq handler would trigger nevertheless,
and irq/pm.c:irq_pm_check_wakeup would be called, which would
try to call irq_disable. However, if the interrupt is not enabled
(irqd_irq_disabled(&desc->irq_data) is true), the call does nothing,
and the interrupt is left enabled in the eint driver.
Especially for level-sensitive interrupts, this will lead to an
interrupt storm on resume.
If we detect that an interrupt is only in wake_mask, but not in
cur_mask, we can just mask it out immediately (as mtk_eint_resume
would do anyway at a later stage in the resume sequence, when
restoring cur_mask).
Fixes: bf22ff45bed6 ("genirq: Avoid unnecessary low level irq function calls")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently, in suspend() and resume(), ishtp client drivers are using
driver_data to get "struct ishtp_cl_device" object which is set by
bus driver. It's wrong since the driver_data should not be owned bus.
driver_data should be owned by the corresponding ishtp client driver.
Due to this, some ishtp client driver like cros_ec_ishtp which uses
its driver_data to transfer its data to its child doesn't work correctly.
So this patch removes setting driver_data in bus drier and instead of
using driver_data to get "struct ishtp_cl_device", since "struct device"
is embedded in "struct ishtp_cl_device", we introduce a helper function
that returns "struct ishtp_cl_device" from "struct device".
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There's a new ALPS touchpad/pointstick combo device that requires
MT_CLS_WIN_8_DUAL to make its pointsitck work as a mouse.
The device can be found on HP ZBook 17 G5.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The HID++ spec also defines very long HID++ reports, with a reportid of
0x12. The MX5000 and MX5500 keyboards use 0x12 output reports for sending
messages to display on their buildin LCD.
Userspace (libmx5000) supports this, in order for this to work when talking
to the HID devices instantiated for the keyboard by hid-logitech-dj,
we need to properly forward these reports to the device.
This commit fixes logi_dj_ll_raw_request not forwarding these reports.
Fixes: f2113c3020ef ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add support for Huion HS64 drawing tablet to hid-uclogic
Signed-off-by: Kyle Godbey <me@kyle.ee>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
I've spotted another Chicony PixArt mouse in the wild, which requires
HID_QUIRK_ALWAYS_POLL quirk, otherwise it disconnects each minute.
USB ID of this device is 0x04f2:0x0939.
We've introduced quirks like this for other models before, so lets add
this mouse too.
Link: https://github.com/sriemer/fix-linux-mouse#usb-mouse-disconnectsreconnects-every-minute-on-linux
Signed-off-by: Oleksandr Natalenko <oleksandr@redhat.com>
Acked-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We have to print the filename first before we can kfree it.
Fixes: 91b228107da3 ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
drm_connector_update_edid_property can sleep, we must not
call it while holding a spinlock. Move the callsite.
Fixes: b4b01b4995fb ("drm/virtio: add edid support")
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190405044602.2334-1-kraxel@redhat.com
|
|
The fixed dividers for the emac clocks should be 2 not 4.
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
DM verity should also use DMERR_LIMIT to limit repeat data block
corruption messages.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
For the first call to realloc_argv() in dm_split_args(), old_argv is
NULL and size is zero. Then memcpy is called, with the NULL old_argv
as the source argument and a zero size argument. AFAIK, this is
undefined behavior and generates the following warning when compiled
with UBSAN on ppc64le:
In file included from ./arch/powerpc/include/asm/paca.h:19,
from ./arch/powerpc/include/asm/current.h:16,
from ./include/linux/sched.h:12,
from ./include/linux/kthread.h:6,
from drivers/md/dm-core.h:12,
from drivers/md/dm-table.c:8:
In function 'memcpy',
inlined from 'realloc_argv' at drivers/md/dm-table.c:565:3,
inlined from 'dm_split_args' at drivers/md/dm-table.c:588:9:
./include/linux/string.h:345:9: error: argument 2 null where non-null expected [-Werror=nonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/dm-table.c: In function 'dm_split_args':
./include/linux/string.h:345:9: note: in a call to built-in function '__builtin_memcpy'
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Currently, although we submit super bios in order (and super.nr_entries
is incremented by each logged entry), submit_bio() is async so each
super sector may not be written to log device in order and then the
final nr_entries may be smaller than it should be.
This problem can be reproduced by the xfstests generic/455 with ext4:
QA output created by 455
-Silence is golden
+mark 'end' does not exist
Fix this by serializing submission of super sectors to make sure each
is written to the log disk in order.
Fixes: 0e9cebe724597 ("dm: add log writes target")
Cc: stable@vger.kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Suggested-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
These printing macros already add a trailing newline, so having another
one here just makes for blank lines when these prints are enabled.
Remove these needless newlines.
Fixes: 6bbc923dfcf5 ("dm: add support to directly boot to a mapped device")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Fix 2 kstrndup() calls with incorrect argument order.
Fixes: 6bbc923dfcf5 ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org # v5.1
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The actual layout for OCELOT_GPIO_ALT[01] when there are more than 32 pins
is interleaved, i.e. OCELOT_GPIO_ALT0[0], OCELOT_GPIO_ALT1[0],
OCELOT_GPIO_ALT0[1], OCELOT_GPIO_ALT1[1]. Introduce a new REG_ALT macro to
facilitate the register offset calculation and use it where necessary.
Fixes: da801ab56ad8 pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The third argument passed to REG is not the correct one and
ocelot_gpio_set_direction is not working for pins after 31. Fix that by
passing the pin number instead of the modulo 32 value.
Fixes: da801ab56ad8 pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently probing of the mcp23s08 results in an error message
"detected irqchip that is shared with multiple gpiochips:
please fix the driver"
This is due to the following:
Call to mcp23s08_irqchip_setup() with call hierarchy:
mcp23s08_irqchip_setup()
gpiochip_irqchip_add_nested()
gpiochip_irqchip_add_key()
gpiochip_set_irq_hooks()
Call to devm_gpiochip_add_data() with call hierarchy:
devm_gpiochip_add_data()
gpiochip_add_data_with_key()
gpiochip_add_irqchip()
gpiochip_set_irq_hooks()
The gpiochip_add_irqchip() returns immediately if there isn't a irqchip
but we added a irqchip due to the previous mcp23s08_irqchip_setup()
call. So it calls gpiochip_set_irq_hooks() a second time.
Fix this by moving the call to devm_gpiochip_add_data before
the call to mcp23s08_irqchip_setup
Fixes: 02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")
Suggested-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd bugfix from Lee Jones.
Fix stmfx type confusion between regmap_read() (which takes an "u32")
and the bitmap operations (which take an "unsigned long" array).
* tag 'mfd-fixes-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: stmfx: Fix an endian bug in stmfx_irq_handler()
mfd: stmfx: Uninitialized variable in stmfx_irq_handler()
|
|
The syzbot reported
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long. We want the
pointer here, not the address of it.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Fixes: e4bf63482c30 ("qmi_wwan: Add quirk for Quectel dynamic config")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the MAC address setup in the probe. The MAC address
retrieved using of_get_mac_address was checked for not containing an
error, but it may also be NULL which wasn't tested. Fix it by replacing
IS_ERR with IS_ERR_OR_NULL.
Fixes: 541ddc66d665 ("net: macb: support of_get_mac_address new ERR_PTR error")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not okay to cast a "u32 *" to "unsigned long *" when you are
doing a for_each_set_bit() loop because that will break on big
endian systems.
Fixes: 386145601b82 ("mfd: stmfx: Uninitialized variable in stmfx_irq_handler()")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
|
|
Pull auxdisplay cleanup from Miguel Ojeda:
"A cleanup for two drivers in auxdisplay: convert them to use
vm_map_pages_zero() (Souptick Joarder)"
* tag 'auxdisplay-for-linus-v5.2-rc7' of git://github.com/ojeda/linux:
auxdisplay/ht16k33.c: Convert to use vm_map_pages_zero()
auxdisplay/cfag12864bfb.c: Convert to use vm_map_pages_zero()
|
|
SPI memory devices from different manufacturers have widely
different configurations for Status, Control and Configuration
registers. JEDEC 216C defines a new map for these common register
bits and their functions, and describes how the individual bits may
be accessed for a specific device. For the JEDEC 216B compliant
flashes, we can partially deduce Status and Configuration registers
functions by inspecting the 16th DWORD of BFPT. Older flashes that
don't declare the SFDP tables (SPANSION FL512SAIFG1 311QQ063 A ©11
SPANSION) let the software decide how to interact with these registers.
The commit dcb4b22eeaf4 ("spi-nor: s25fl512s supports region locking")
uncovered a probe error for s25fl512s, when the Quad Enable bit CR[1]
was set to one in the bootloader. When this bit is one, only the Write
Status (01h) command with two data byts may be used, the 01h command with
one data byte is not recognized and hence the error when trying to clear
the block protection bits.
Fix the above by using the Write Status (01h) command with two data bytes
when the Quad Enable bit is one.
Backward compatibility should be fine. The newly introduced
spi_nor_spansion_clear_sr_bp() is tightly coupled with the
spansion_quad_enable() function. Both assume that the Write Register
with 16 bits, together with the Read Configuration Register (35h)
instructions are supported.
Fixes: dcb4b22eeaf44f91 ("spi-nor: s25fl512s supports region locking")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Jonas Bonn <jonas@norrbonn.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Since commit 605ad7f184b60cfaacbc038aa6c55ee68dee3c89 "tcp: refine TSO autosizing",
outbound throughput is dramatically reduced for some connections, as sis900
is doing TX completion within idle states only.
Make TX completion happen after every transmitted packet.
Test:
netperf
before patch:
> netperf -H remote -l -2000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 253.44 0.06
after patch:
> netperf -H remote -l -10000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 5.38 14.89
Thx to Dave Miller and Eric Dumazet for helpful hints
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When transmitting certain PTP frames, e.g. SYNC and DELAY_REQ, the
PTP daemon, e.g. ptp4l, is polling the driver for the frame transmit
hardware timestamp. The polling will most likely timeout if the tx
coalesce is enabled due to the Interrupt-on-Completion (IC) bit is
not set in tx descriptor for those frames.
This patch will ignore the tx coalesce parameter and set the IC bit
when transmitting PTP frames which need to report out the frame
transmit hardware timestamp to user space.
Fixes: f748be531d70 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ADDSUB bit is set, the system time seconds field is calculated as
the complement of the seconds part of the update value.
For example, if 3.000000001 seconds need to be subtracted from the
system time, this field is calculated as
2^32 - 3 = 4294967296 - 3 = 0x100000000 - 3 = 0xFFFFFFFD
Previously, the 0x100000000 is mistakenly written as 100000000.
This is further simplified from
sec = (0x100000000ULL - sec);
to
sec = -sec;
Fixes: ba1ffd74df74 ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fix from Joerg Roedel:
"Revert a commit from the previous pile of fixes which causes new
lockdep splats. It is better to revert it for now and work on a better
and more well tested fix"
* tag 'iommu-fix-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"
|
|
device_domain_lock"
This reverts commit 7560cc3ca7d9d11555f80c830544e463fcdb28b8.
With 5.2.0-rc5 I can easily trigger this with lockdep and iommu=pt:
======================================================
WARNING: possible circular locking dependency detected
5.2.0-rc5 #78 Not tainted
------------------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000ea2b3beb (&(&iommu->lock)->rlock){+.+.}, at: domain_context_mapping_one+0xa5/0x4e0
but task is already holding lock:
00000000a681907b (device_domain_lock){....}, at: domain_context_mapping_one+0x8d/0x4e0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (device_domain_lock){....}:
_raw_spin_lock_irqsave+0x3c/0x50
dmar_insert_one_dev_info+0xbb/0x510
domain_add_dev_info+0x50/0x90
dev_prepare_static_identity_mapping+0x30/0x68
intel_iommu_init+0xddd/0x1422
pci_iommu_init+0x16/0x3f
do_one_initcall+0x5d/0x2b4
kernel_init_freeable+0x218/0x2c1
kernel_init+0xa/0x100
ret_from_fork+0x3a/0x50
-> #0 (&(&iommu->lock)->rlock){+.+.}:
lock_acquire+0x9e/0x170
_raw_spin_lock+0x25/0x30
domain_context_mapping_one+0xa5/0x4e0
pci_for_each_dma_alias+0x30/0x140
dmar_insert_one_dev_info+0x3b2/0x510
domain_add_dev_info+0x50/0x90
dev_prepare_static_identity_mapping+0x30/0x68
intel_iommu_init+0xddd/0x1422
pci_iommu_init+0x16/0x3f
do_one_initcall+0x5d/0x2b4
kernel_init_freeable+0x218/0x2c1
kernel_init+0xa/0x100
ret_from_fork+0x3a/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(device_domain_lock);
lock(&(&iommu->lock)->rlock);
lock(device_domain_lock);
lock(&(&iommu->lock)->rlock);
*** DEADLOCK ***
2 locks held by swapper/0/1:
#0: 00000000033eb13d (dmar_global_lock){++++}, at: intel_iommu_init+0x1e0/0x1422
#1: 00000000a681907b (device_domain_lock){....}, at: domain_context_mapping_one+0x8d/0x4e0
stack backtrace:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc5 #78
Hardware name: LENOVO 20KGS35G01/20KGS35G01, BIOS N23ET50W (1.25 ) 06/25/2018
Call Trace:
dump_stack+0x85/0xc0
print_circular_bug.cold.57+0x15c/0x195
__lock_acquire+0x152a/0x1710
lock_acquire+0x9e/0x170
? domain_context_mapping_one+0xa5/0x4e0
_raw_spin_lock+0x25/0x30
? domain_context_mapping_one+0xa5/0x4e0
domain_context_mapping_one+0xa5/0x4e0
? domain_context_mapping_one+0x4e0/0x4e0
pci_for_each_dma_alias+0x30/0x140
dmar_insert_one_dev_info+0x3b2/0x510
domain_add_dev_info+0x50/0x90
dev_prepare_static_identity_mapping+0x30/0x68
intel_iommu_init+0xddd/0x1422
? printk+0x58/0x6f
? lockdep_hardirqs_on+0xf0/0x180
? do_early_param+0x8e/0x8e
? e820__memblock_setup+0x63/0x63
pci_iommu_init+0x16/0x3f
do_one_initcall+0x5d/0x2b4
? do_early_param+0x8e/0x8e
? rcu_read_lock_sched_held+0x55/0x60
? do_early_param+0x8e/0x8e
kernel_init_freeable+0x218/0x2c1
? rest_init+0x230/0x230
kernel_init+0xa/0x100
ret_from_fork+0x3a/0x50
domain_context_mapping_one() is taking device_domain_lock first then
iommu lock, while dmar_insert_one_dev_info() is doing the reverse.
That should be introduced by commit:
7560cc3ca7d9 ("iommu/vt-d: Fix lock inversion between iommu->lock and
device_domain_lock", 2019-05-27)
So far I still cannot figure out how the previous deadlock was
triggered (I cannot find iommu lock taken before calling of
iommu_flush_dev_iotlb()), however I'm pretty sure that that change
should be incomplete at least because it does not fix all the places
so we're still taking the locks in different orders, while reverting
that commit is very clean to me so far that we should always take
device_domain_lock first then the iommu lock.
We can continue to try to find the real culprit mentioned in
7560cc3ca7d9, but for now I think we should revert it to fix current
breakage.
CC: Joerg Roedel <joro@8bytes.org>
CC: Lu Baolu <baolu.lu@linux.intel.com>
CC: dave.jiang@intel.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"If an IOMMU is present, ignore the P2PDMA whitelist we added for v5.2
because we don't yet know how to support P2PDMA in that case (Logan
Gunthorpe)"
* tag 'pci-v5.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three driver fixes (and one version number update): a suspend hang in
ufs, a qla hard lock on module removal and a qedi panic during
discovery"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix hardlockup in abort command during driver remove
scsi: ufs: Avoid runtime suspend possibly being blocked forever
scsi: qedi: update driver version to 8.37.0.20
scsi: qedi: Check targetname while finding boot target information
|
|
The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a
softdep line, so that the corresponding module gets prepared
gracefully. Without this, a simple inclusion to initrd via dracut
failed due to the missing dependency, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.
Changes in v2:
- added fixes header
Fixes: 4276e47e2d1c ("be2net: Add link test to list of ethtool self tests.")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the variable set function from "efivar_entry_set" to
"efivar_entry_set_safe" in efibc panic notifier.
In safe function parameter "block" will set to false
and will call "efivar_entry_set_nonblocking"to set efi variables.
efivar_entry_set_nonblocking is guaranteed to
not block and is suitable for calling from crash/panic handlers.
In UEFI android platform, when warm reset happens,
with this change, efibc will not block the reboot process.
Otherwise, set variable will call queue work and send to other offlined
cpus then cause another panic, finally will cause reboot failure.
Signed-off-by: Tian Baofeng <baofeng.tian@intel.com>
Signed-off-by: Luo XinanX <xinanx.luo@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
|
|
Pull rdma fixes from Doug Ledford:
"This is probably our last -rc pull request. We don't have anything
else outstanding at the moment anyway, and with the summer months on
us and people taking trips, I expect the next weeks leading up to the
merge window to be pretty calm and sedate.
This has two simple, no brainer fixes for the EFA driver.
Then it has ten not quite so simple fixes for the hfi1 driver. The
problem with them is that they aren't simply one liner typo fixes.
They're still fixes, but they're more complex issues like livelock
under heavy load where the answer was to change work queue usage and
spinlock usage to resolve the problem, or issues with orphaned
requests during certain types of failures like link down which
required some more complex work to fix too. They all look like
legitimate fixes to me, they just aren't small like I wish they were.
Summary:
- 2 minor EFA fixes
- 10 hfi1 fixes related to scaling issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/efa: Handle mmap insertions overflow
RDMA/efa: Fix success return value in case of error
IB/hfi1: Handle port down properly in pio
IB/hfi1: Handle wakeup of orphaned QPs for pio
IB/hfi1: Wakeup QPs orphaned on wait list after flush
IB/hfi1: Use aborts to trigger RC throttling
IB/hfi1: Create inline to get extended headers
IB/hfi1: Silence txreq allocation warnings
IB/hfi1: Avoid hardlockup with flushlist_lock
IB/hfi1: Correct tid qp rcd to match verbs context
IB/hfi1: Close PSM sdma_progress sleep window
IB/hfi1: Validate fault injection opcode user input
|
|
Pull drm fixes from Dave Airlie:
"Just catching up on the week since back from holidays, everything
seems quite sane.
core:
- copy_to_user fix for really legacy codepaths.
vmwgfx:
- two dma fixes
- one virt hw interaction fix
i915:
- modesetting fix
- gvt fix
panfrost:
- BO unmapping fix
imx:
- image converter fixes"
* tag 'drm-fixes-2019-06-21' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Don't clobber M/N values during fastset check
drm: return -EFAULT if copy_to_user() fails
drm/panfrost: Make sure a BO is only unmapped when appropriate
drm/i915/gvt: ignore unexpected pvinfo write
gpu: ipu-v3: image-convert: Fix image downsize coefficients
gpu: ipu-v3: image-convert: Fix input bytesperline for packed formats
gpu: ipu-v3: image-convert: Fix input bytesperline width/height align
drm/vmwgfx: fix a warning due to missing dma_parms
drm/vmwgfx: Honor the sg list segment size limitation
drm/vmwgfx: Use the backdoor port if the HB port is not available
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO/counter fixes from Greg KH:
"Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so
that's why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the
erofs filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues"
* tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: erofs: add requirements field in superblock
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 5.2-rc6
Nothing major, just fixes for reported issues:
- soundwire fixes
- thunderbolt fixes
- MAINTAINERS update for fpga maintainer change
- binder bugfix
- habanalabs 64bit pointer fix
- documentation updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: use u64_to_user_ptr() for reading user pointers
doc: fix documentation about UIO_MEM_LOGICAL using
MAINTAINERS / Documentation: Thorsten Scherer is the successor of Gavin Schenk
docs: fb: Add TER16x32 to the available font names
MAINTAINERS: fpga: hand off maintainership to Moritz
thunderbolt: Implement CIO reset correctly for Titan Ridge
binder: fix possible UAF when freeing buffer
thunderbolt: Make sure device runtime resume completes before taking domain lock
soundwire: intel: set dai min and max channels correctly
soundwire: stream: fix bad unlock balance
soundwire: stream: fix out of boundary access on port properties
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are four small USB fixes for 5.2-rc6.
They include two xhci bugfixes, a chipidea fix, and a small dwc2 fix.
Nothing major, just nice things to get resolved for reported issues.
All have been in linux-next with no reported issues"
* tag 'usb-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: detect USB 3.2 capable host controllers correctly
usb: xhci: Don't try to recover an endpoint if port is in error state.
usb: dwc2: Use generic PHY width in params setup
usb: chipidea: udc: workaround for endpoint conflict issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: ipu-v3 image converter fixes
This series fixes input buffer alignment and downsizer configuration
to adhere to IPU mem2mem CSC/scaler hardware restrictions in certain
downscaling ratios.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1561040798.14349.20.camel@pengutronix.de
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.2-rc6:
- GVT: Fix reserved PVINFO register write (Weinan)
- Avoid clobbering M/N values in fastset fuzzy checks (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87pnn8sbdp.fsf@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
panfrost- Only unmap BO's if they're mapped (Boris)
core- Handle buffer desc copy_to_user failure properly (Dan)
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619192745.GA145841@art_vandelay
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
A couple of fixes for vmwgfx. Two fixes for a DMA sg-list debug warning
message. These are not cc'd stable since there is no evidence of actual
breakage.
On fix for the high-bandwidth backdoor port which is cc'd stable due to
upcoming hardware, on which the code would otherwise break.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <VMware> <thomas@shipmail.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618072255.2720-1-thomas@shipmail.org
|
