| Age | Commit message (Collapse) | Author |
|---|
|
Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a rudimentary Clause 45 driver for the BCM84881 PHY, found on
Methode DM7052 SFPs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.
Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.
This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called. At that point, we either have a PHY, or we don't.
We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Split link_an_mode between the configured setting and the current
operating setting. This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Some SFP+ modules have Clause 45 PHYs embedded on them, which need a
little more handling in order to ensure that they are correctly setup,
as they switch the PHY link mode according to the negotiated speed.
With Clause 22 PHYs, we assumed that they would operate in SGMII mode,
but this assumption is now false. Adapt phylink to support Clause 45
PHYs on SFP+ modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
In order to support Clause 45 PHYs on SFP+ modules, which have an
indeterminant phy interface mode, we need to be able to call
phylink_bringup_phy() with a different interface mode to that used when
binding the PHY. Reduce __phylink_connect_phy() to an attach operation,
and move the call to phylink_bringup_phy() to its call sites.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Some SFP+ modules have PHYs on them just like SFP modules do, except
they are Clause 45 PHYs. The I2C protocol used to access them is
modified slightly in order to send the device address and 16-bit
register index.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.
An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.
However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.
This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.
Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes. Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Pull block fix from Jens Axboe:
"Unfortunately this weekend we had a few last minute reports, one was
for block.
The partition disable for zoned devices was overly restrictive, it can
work (and be supported) just fine for host-aware variants.
Here's a fix ensuring that's the case so we don't break existing users
of that"
* tag 'block-5.5-2020-01-26' of git://git.kernel.dk/linux-block:
block: allow partitions on host aware zone devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two last minute fixes, both in drivers.
The fnic one is a highly unlikely condition, but the RDMA one is a
recently introduced regression that causes a kernel warning to trigger
in every RDMA logon, which would be unsightly if it got into the final
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: RDMA/isert: Fix a recently introduced regression related to logout
scsi: fnic: do not queue commands during fwreset
|
|
Host-aware SMR drives can be used with the commands to explicitly manage
zone state, but they can also be used as normal disks. In the former
case it makes perfect sense to allow partitions on them, in the latter
it does not, just like for host managed devices. Add a check to
add_partition to allow partitions on host aware devices, but give
up any zone management capabilities in that case, which also catches
the previously missed case of adding a partition vs just scanning it.
Because sd can rescan the attribute at runtime it needs to check if
a disk has partitions, for which a new helper is added to genhd.h.
Fixes: 5eac3eb30c9a ("block: Remove partition support for zoned block devices")
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Off by one in mt76 airtime calculation, from Dan Carpenter.
2) Fix TLV fragment allocation loop condition in iwlwifi, from Luca
Coelho.
3) Don't confirm neigh entries when doing ipsec pmtu updates, from Xu
Wang.
4) More checks to make sure we only send TSO packets to lan78xx chips
that they can actually handle. From James Hughes.
5) Fix ip_tunnel namespace move, from William Dauchy.
6) Fix unintended packet reordering due to cooperation between
listification done by GRO and non-GRO paths. From Maxim
Mikityanskiy.
7) Add Jakub Kicincki formally as networking co-maintainer.
8) Info leak in airo ioctls, from Michael Ellerman.
9) IFLA_MTU attribute needs validation during rtnl_create_link(), from
Eric Dumazet.
10) Use after free during reload in mlxsw, from Ido Schimmel.
11) Dangling pointers are possible in tp->highest_sack, fix from Eric
Dumazet.
12) Missing *pos++ in various networking seq_next handlers, from Vasily
Averin.
13) CHELSIO_GET_MEM operation neds CAP_NET_ADMIN check, from Michael
Ellerman.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (109 commits)
firestream: fix memory leaks
net: cxgb3_main: Add CAP_NET_ADMIN check to CHELSIO_GET_MEM
net: bcmgenet: Use netif_tx_napi_add() for TX NAPI
tipc: change maintainer email address
net: stmmac: platform: fix probe for ACPI devices
net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path
net/mlx5e: kTLS, Remove redundant posts in TX resync flow
net/mlx5e: kTLS, Fix corner-case checks in TX resync flow
net/mlx5e: Clear VF config when switching modes
net/mlx5: DR, use non preemptible call to get the current cpu number
net/mlx5: E-Switch, Prevent ingress rate configuration of uplink rep
net/mlx5: DR, Enable counter on non-fwd-dest objects
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix lowest FDB pool size
net: Fix skb->csum update in inet_proto_csum_replace16().
netfilter: nf_tables: autoload modules from the abort path
netfilter: nf_tables: add __nft_chain_type_get()
netfilter: nf_tables_offload: fix check the chain offload flag
netfilter: conntrack: sctp: use distinct states for new SCTP connections
ipv6_route_seq_next should increase position index
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
|
|
In fs_open(), 'vcc' is allocated through kmalloc() and assigned to
'atm_vcc->dev_data.' In the following execution, if an error occurs, e.g.,
there is no more free channel, an error code EBUSY or ENOMEM will be
returned. However, 'vcc' is not deallocated, leading to memory leaks. Note
that, in normal cases where fs_open() returns 0, 'vcc' will be deallocated
in fs_close(). But, if fs_open() fails, there is no guarantee that
fs_close() will be invoked.
To fix this issue, deallocate 'vcc' before the error code is returned.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single fix for the Intel Sunrisepoint pin controller that makes the
interrupts work properly on it"
* tag 'pinctrl-v5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 7587935cfa11 ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa11 ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- add sanity checks to USB endpoints in various dirvers
- max77650-onkey was missing an OF table which was preventing module
autoloading
- a revert and a different fix for F54 handling in Synaptics dirver
- a fixup for handling register in pm8xxx vibrator driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pm8xxx-vib - fix handling of separate enable register
Input: keyspan-remote - fix control-message timeouts
Input: max77650-onkey - add of_match table
Input: rmi_f54 - read from FIFO in 32 byte blocks
Revert "Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers"
Input: sur40 - fix interface sanity checks
Input: gtco - drop redundant variable reinit
Input: gtco - fix extra-descriptor debug message
Input: gtco - fix endpoint sanity check
Input: aiptek - use descriptors of current altsetting
Input: aiptek - fix endpoint sanity check
Input: pegasus_notetaker - fix endpoint sanity check
Input: sun4i-ts - add a check for devm_thermal_zone_of_sensor_register
Input: evdev - convert kzalloc()/vzalloc() to kvzalloc()
|
|
https://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
Fix OP-TEE compile error with nommu
* tag 'tee-optee-fix2-for-5.5' of https://git.linaro.org:/people/jens.wiklander/linux-tee:
tee: optee: Fix compilation issue with nommu
Link: https://lore.kernel.org/r/20200123101310.GA10320@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec4974240 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Fixes: 556b9d16d3f5 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two fixes:
- Fix NULL-ptr dereference bug in Intel IOMMU driver
- Properly save and restore AMD IOMMU performance counter registers
when testing if they are writable"
* tag 'iommu-fixes-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU perf counter clobbering during init
iommu/vt-d: Call __dmar_remove_one_dev_info with valid pointer
|
|
Pull drm fixes from Dave Airlie:
"This one has a core mst fix and two i915 fixes. amdgpu just enables
some hw outside experimental.
The panfrost fix is a little bigger than I'd like at this stage but it
fixes a fairly fundamental problem with global shared buffers in that
driver, and since it's confined to that driver and I've taken a look
at it, I think it's fine to get into the tree now, so it can get
stable propagated as well.
core/mst:
- Fix SST branch device handling
amdgpu:
- enable renoir outside experimental
i915:
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
panfrost:
- Fix mapping of globally visible BO's (Boris)"
* tag 'drm-fixes-2020-01-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: remove the experimental flag for renoir
drm/panfrost: Add the panfrost_gem_mapping concept
drm/i915: Align engine->uabi_class/instance with i915_drm.h
drm/i915/userptr: fix size calculation
drm/dp_mst: Handle SST-only branch device case
|
|
init_iommu_perf_ctr() clobbers the register when it checks write access
to IOMMU perf counters and fails to restore when they are writable.
Add save and restore to fix it.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 30861ddc9cca4 ("perf/x86/amd: Add IOMMU Performance Counter resource management")
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
It is possible for archdata.iommu to be set to
DEFER_DEVICE_DOMAIN_INFO or DUMMY_DEVICE_DOMAIN_INFO so check for
those values before calling __dmar_remove_one_dev_info. Without a
check it can result in a null pointer dereference. This has been seen
while booting a kdump kernel on an HP dl380 gen9.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org # 5.3+
Cc: linux-kernel@vger.kernel.org
Fixes: ae23bfb68f28 ("iommu/vt-d: Detach domain before using a private one")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a hw_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci: Fix minimum clock rate for v3 controllers
- sdhci-tegra: Fix SDR50 tuning override
- sdhci_am654: Fixup tuning issues and support for CQHCI
- sdhci_am654: Remove wrong write protect flag"
* tag 'mmc-v5.5-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: fix minimum clock rate for v3 controller
mmc: tegra: fix SDR50 tuning override
mmc: sdhci_am654: Fix Command Queuing in AM65x
mmc: sdhci_am654: Reset Command and Data line after tuning
mmc: sdhci_am654: Remove Inverted Write Protect flag
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.5-2020-01-23:
amdgpu:
- remove the experimental flag from renoir
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123191424.3849-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135045.GA12584@jlahtine-desk.ger.corp.intel.com
|
|
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
