| Age | Commit message (Collapse) | Author |
|---|
|
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Intel Keem Bay platform supports multi-master operations over same i2c
bus using Synopsys i2c DesignWare IP. When multi-masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c DesignWare driver does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for the following conditions:
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use i2c_timings struct and corresponding methods to get bus clock frequency
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In interrupt mode we clear the status flags twice, in the interrupt
handler and in i801_check_post(). Remove clearing the status flags
from i801_check_post() and handle polling mode by using the
SMBus unlocking write to also clear the status flags if still set.
To be precise: One could still argue that the status flags are
cleared twice in interrupt mode, but it comes for free.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I see no need to read back the registers to verify that the bits
have actually been cleared. I can't imagine any scenario where
the bits would remain set after a write to them.
Whilst at it, change involved syslog messages to use pci_dbg() et al.
to simplify them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C controller chosen by I2C_EXYNOS5 config option is also suitable for
Exynos850 and ExynosAutoV9 SoCs. State that specifically in I2C_EXYNOS5
symbol help section.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In new Exynos SoCs (like Exynos850) where HSI2C is implemented as a
part of USIv2 block, there are two clocks provided to HSI2C controller:
- PCLK: bus clock (APB), provides access to register interface
- IPCLK: operating IP-core clock; SCL is derived from this one
Both clocks have to be asserted for HSI2C to be functional in that case.
Add code to obtain and enable/disable PCLK in addition to already
handled operating clock. Make it optional though, as older Exynos SoC
variants only have one HSI2C clock.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
ExynosAutoV9 functioning logic mostly follows I2C_TYPE_EXYNOS7, but
timing calculation and configuration procedure is changed: e.g. only
timing_s3 has to be set now.
Another change of HSI2C controller in ExynosAutoV9 SoC is that it's now
a part of USIv2 IP-core. No changes is needed for I2C driver though, as
all USI related configuration is done in USI driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The log messages talk about 'bus recovery' while it is not a bus
recovery with 9 pulses but merely a controller reset. Controller resets
are not worth log messages. The 'bus busy' message should be emitted by
upper layers, a busy bus may be expected in some cases.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
|
|
Function stm32f7_i2c_release_bus is always returning 0, hence it
should be a void function. Update the function and remove the
return value error checking code in caller functions.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit e8578547ce59ddba3651ac0e68dbcb6daa8ce790. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit 36af188f795bd1b0d794dd735623979dc6b698d3. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The platform data structures are used in the respective i801_add_tco
functions only. Therefore we can make the definitions local to these
functions.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Set optimal HCNT, LCNT and hold time values for all the speeds supported
in Intel Programmable Service Engine I2C controller in Intel Elkhart
Lake.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support to configure HCNT, LCNT values for Fast Mode Plus and High
Speed Mode.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This enables the async suspend for i2c client devices. This reduces
the suspend/resume time considerably on platforms where i2c devices
can take a lot of time (hundreds of ms) to resume.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Enable async suspend/resume of i2c adapters. It enormously helps with
reducing the resume time of systems (as much as 20%-40%) where I2C devices
can take significant time (100s of ms) to resume.
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Mark the designware devices for asynchronous suspend. With this, the
resume for designware devices does not get stuck behind other unrelated
devices (e.g. intel_backlight that takes hundreds of ms to resume,
waiting for its parent devices).
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
$ scripts/kernel-doc -none drivers/i2c/busses/i2c-designware-core.h
warning: Function parameter or member 'rst' not described in 'dw_i2c_dev'
warning: Function parameter or member 'get_clk_rate_khz' not described in 'dw_i2c_dev'
warning: Function parameter or member 'flags' not described in 'dw_i2c_dev'
warning: Function parameter or member 'functionality' not described in 'dw_i2c_dev'
warning: Function parameter or member 'master_cfg' not described in 'dw_i2c_dev'
warning: Function parameter or member 'set_sda_hold_time' not described in 'dw_i2c_dev'
warning: Function parameter or member 'rinfo' not described in 'dw_i2c_dev'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunla@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
clk_get_rate() is documented as requiring the clock to be enabled.
Ensure that the bus clock is enabled before calling clk_get_rate() in
rk3x_i2c_probe() to satisfy this requirement.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reduce source code and code size by defining the chip features
statically.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support for the ACPI based device registration so that the driver
can be also enabled through ACPI table.
This does not include the ACPI support for Tegra VI and DVC I2C.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
|
|
Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin:
"Misc fixes all over the place.
Revert of virtio used length validation series: the approach taken
does not seem to work, breaking too many guests in the process. We'll
need to do length validation using some other approach"
[ This merge also ends up reverting commit f7a36b03a732 ("vsock/virtio:
suppress used length validation"), which came in through the
networking tree in the meantime, and was part of that whole used
length validation series - Linus ]
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim: avoid putting an uninitialized iova_domain
vhost-vdpa: clean irqs before reseting vdpa device
virtio-blk: modify the value type of num in virtio_queue_rq()
vhost/vsock: cleanup removing `len` variable
vhost/vsock: fix incorrect used length reported to the guest
Revert "virtio_ring: validate used buffer length"
Revert "virtio-net: don't let virtio core to validate used length"
Revert "virtio-blk: don't let virtio core to validate used length"
Revert "virtio-scsi: don't let virtio core to validate used buffer length"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes:
- Remove unused PASID_DISABLED
- Fix RCU locking
- Fix for the unmap_pages call-back
- Rockchip RK3568 address mask fix
- AMD IOMMUv2 log message clarification
* tag 'iommu-fixes-v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix unmap_pages support
iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
iommu/rockchip: Fix PAGE_DESC_HI_MASKs for RK3568
iommu/amd: Clarify AMD IOMMUv2 initialization messages
iommu/vt-d: Remove unused PASID_DISABLED
|
|
Use the architecture independent Kconfig option PAGE_SIZE_LESS_THAN_64KB
to indicate that VMXNET3 requires a page size smaller than 64kB.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more block fixes from Jens Axboe:
"Turns out that the flushing out of pending fixes before the
Thanksgiving break didn't quite work out in terms of timing, so here's
a followup set of fixes:
- rq_qos_done() should be called regardless of whether or not we're
the final put of the request, it's not related to the freeing of
the state. This fixes an IO stall with wbt that a few users have
reported, a regression in this release.
- Only define zram_wb_devops if it's used, fixing a compilation
warning for some compilers"
* tag 'block-5.16-2021-11-27' of git://git.kernel.dk/linux-block:
zram: only make zram_wb_devops for CONFIG_ZRAM_WRITEBACK
block: call rq_qos_done() before ref check in batch completions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve fixes, eleven in drivers (target, qla2xx, scsi_debug, mpt3sas,
ufs). The core fix is a minor correction to the previous state update
fix for the iscsi daemons"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Zero clear zones at reset write pointer
scsi: core: sysfs: Fix setting device state to SDEV_RUNNING
scsi: scsi_debug: Sanity check block descriptor length in resp_mode_select()
scsi: target: configfs: Delete unnecessary checks for NULL
scsi: target: core: Use RCU helpers for INQUIRY t10_alua_tg_pt_gp
scsi: mpt3sas: Fix incorrect system timestamp
scsi: mpt3sas: Fix system going into read-only mode
scsi: mpt3sas: Fix kernel panic during drive powercycle test
scsi: ufs: ufs-mediatek: Add put_device() after of_find_device_by_node()
scsi: scsi_debug: Fix type in min_t to avoid stack OOB
scsi: qla2xxx: edif: Fix off by one bug in qla_edif_app_getfcinfo()
scsi: ufs: ufshpb: Fix warning in ufshpb_set_hpb_read_to_upiu()
|
|
When supporting only the .map and .unmap callbacks of iommu_ops,
the IOMMU driver can make assumptions about the size and alignment
used for mappings based on the driver provided pgsize_bitmap. VT-d
previously used essentially PAGE_MASK for this bitmap as any power
of two mapping was acceptably filled by native page sizes.
However, with the .map_pages and .unmap_pages interface we're now
getting page-size and count arguments. If we simply combine these
as (page-size * count) and make use of the previous map/unmap
functions internally, any size and alignment assumptions are very
different.
As an example, a given vfio device assignment VM will often create
a 4MB mapping at IOVA pfn [0x3fe00 - 0x401ff]. On a system that
does not support IOMMU super pages, the unmap_pages interface will
ask to unmap 1024 4KB pages at the base IOVA. dma_pte_clear_level()
will recurse down to level 2 of the page table where the first half
of the pfn range exactly matches the entire pte level. We clear the
pte, increment the pfn by the level size, but (oops) the next pte is
on a new page, so we exit the loop an pop back up a level. When we
then update the pfn based on that higher level, we seem to assume
that the previous pfn value was at the start of the level. In this
case the level size is 256K pfns, which we add to the base pfn and
get a results of 0x7fe00, which is clearly greater than 0x401ff,
so we're done. Meanwhile we never cleared the ptes for the remainder
of the range. When the VM remaps this range, we're overwriting valid
ptes and the VT-d driver complains loudly, as reported by the user
report linked below.
The fix for this seems relatively simple, if each iteration of the
loop in dma_pte_clear_level() is assumed to clear to the end of the
level pte page, then our next pfn should be calculated from level_pfn
rather than our working pfn.
Fixes: 3f34f1259776 ("iommu/vt-d: Implement map/unmap_pages() iommu_ops callback")
Reported-by: Ajay Garg <ajaygargnsit@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Link: https://lore.kernel.org/all/20211002124012.18186-1-ajaygargnsit@gmail.com/
Link: https://lore.kernel.org/r/163659074748.1617923.12716161410774184024.stgit@omen
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
If we return -EOPNOTSUPP, the rcu lock remains lock. This is spurious.
Go through the end of the function instead. This way, the missing
'rcu_read_unlock()' is called.
Fixes: 7afd7f6aa21a ("iommu/vt-d: Check FL and SL capability sanity in scalable mode")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/40cc077ca5f543614eab2a10e84d29dd190273f6.1636217517.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With the submission of iommu driver for RK3568 a subtle bug was
introduced: PAGE_DESC_HI_MASK1 and PAGE_DESC_HI_MASK2 have to be
the other way arround - that leads to random errors, especially when
addresses beyond 32 bit are used.
Fix it.
Fixes: c55356c534aa ("iommu: rockchip: Add support for iommu v2")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dan Johansen <strit@manjaro.org>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20211124021325.858139-1-knaerzche@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The messages printed on the initialization of the AMD IOMMUv2 driver
have caused some confusion in the past. Clarify the messages to lower
the confusion in the future.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20211123105507.7654-3-joro@8bytes.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter.
Current release - regressions:
- r8169: fix incorrect mac address assignment
- vlan: fix underflow for the real_dev refcnt when vlan creation
fails
- smc: avoid warning of possible recursive locking
Current release - new code bugs:
- vsock/virtio: suppress used length validation
- neigh: fix crash in v6 module initialization error path
Previous releases - regressions:
- af_unix: fix change in behavior in read after shutdown
- igb: fix netpoll exit with traffic, avoid warning
- tls: fix splice_read() when starting mid-record
- lan743x: fix deadlock in lan743x_phy_link_status_change()
- marvell: prestera: fix bridge port operation
Previous releases - always broken:
- tcp_cubic: fix spurious Hystart ACK train detections for
not-cwnd-limited flows
- nexthop: fix refcount issues when replacing IPv6 groups
- nexthop: fix null pointer dereference when IPv6 is not enabled
- phylink: force link down and retrigger resolve on interface change
- mptcp: fix delack timer length calculation and incorrect early
clearing
- ieee802154: handle iftypes as u32, prevent shift-out-of-bounds
- nfc: virtual_ncidev: change default device permissions
- netfilter: ctnetlink: fix error codes and flags used for kernel
side filtering of dumps
- netfilter: flowtable: fix IPv6 tunnel addr match
- ncsi: align payload to 32-bit to fix dropped packets
- iavf: fix deadlock and loss of config during VF interface reset
- ice: avoid bpf_prog refcount underflow
- ocelot: fix broken PTP over IP and PTP API violations
Misc:
- marvell: mvpp2: increase MTU limit when XDP enabled"
* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: dsa: microchip: implement multi-bridge support
net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
net: mscc: ocelot: set up traps for PTP packets
net: ptp: add a definition for the UDP port for IEEE 1588 general messages
net: mscc: ocelot: create a function that replaces an existing VCAP filter
net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
net: hns3: fix incorrect components info of ethtool --reset command
net: hns3: fix one incorrect value of page pool info when queried by debugfs
net: hns3: add check NULL address for page pool
net: hns3: fix VF RSS failed problem after PF enable multi-TCs
net: qed: fix the array may be out of bound
net/smc: Don't call clcsock shutdown twice when smc shutdown
net: vlan: fix underflow for the real_dev refcnt
ptp: fix filter names in the documentation
ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
nfc: virtual_ncidev: change default device permissions
net/sched: sch_ets: don't peek at classes beyond 'nbands'
net: stmmac: Disable Tx queues when reconfiguring the interface
selftests: tls: test for correct proto_ops
tls: fix replacing proto_ops
...
|
|
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a NULL pointer dereference in the CPPC library code and a
locking issue related to printing the names of ACPI device nodes in
the device properties framework.
Specifics:
- Fix NULL pointer dereference in the CPPC library code occuring on
hybrid systems without CPPC support (Rafael Wysocki).
- Avoid attempts to acquire a semaphore with interrupts off when
printing the names of ACPI device nodes and clean up code on top of
that fix (Sakari Ailus)"
* tag 'acpi-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address three issues in the intel_pstate driver and fix two
problems related to hibernation.
Specifics:
- Make intel_pstate work correctly on Ice Lake server systems with
out-of-band performance control enabled (Adamos Ttofari).
- Fix EPP handling in intel_pstate during CPU offline and online in
the active mode (Rafael Wysocki).
- Make intel_pstate support ITMT on asymmetric systems with
overclocking enabled (Srinivas Pandruvada).
- Fix hibernation image saving when using the user space interface
based on the snapshot special device file (Evan Green).
- Make the hibernation code release the snapshot block device using
the same mode that was used when acquiring it (Thomas Zeitlhofer)"
* tag 'pm-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
cpufreq: intel_pstate: ITMT support for overclocked system
cpufreq: intel_pstate: Fix active mode offline/online EPP handling
cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs
|
|
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368a3 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
