| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Core:
- Fix SETDASA when static and dynamic adress are equal
- Fix cmd_v1 DAA exit criteria
Drivers:
- svc: allow probing without any device"
* tag 'i3c/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix probe failure when no i3c device exist
i3c: master: Fix SETDASA process
dt-bindings: i3c: Fix description for assigned-address
i3c: master: svc: Describe member 'saved_regs'
i3c: master: svc: Do not check for 0 return after calling platform_get_irq()
i3c/master: cmd_v1: Fix the exit criteria for the daa procedure
i3c: Explicitly include correct DT includes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes that came in during the merge window, both driver
specific - one for a bug that came up in testing, one for a bug due
to a misreading of the datasheet"
* tag 'regulator-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6594-regulator: Fix random kernel crash
regulator: tps6287x: Fix n_voltages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes for the sun6i driver. The patch to reduce DMA RX to
single byte width all the time is *hopefully* excessively cautious but
it's unclear which SoCs are affected so the fix just covers everything
for safety"
* tag 'spi-fix-v6.6-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
spi: sun6i: reduce DMA RX transfer width to single byte
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Clean up vCPU targets, always returning generic v8 as the preferred
target
- Trap forwarding infrastructure for nested virtualization (used for
traps that are taken from an L2 guest and are needed by the L1
hypervisor)
- FEAT_TLBIRANGE support to only invalidate specific ranges of
addresses when collapsing a table PTE to a block PTE. This avoids
that the guest refills the TLBs again for addresses that aren't
covered by the table PTE.
- Fix vPMU issues related to handling of PMUver.
- Don't unnecessary align non-stack allocations in the EL2 VA space
- Drop HCR_VIRT_EXCP_MASK, which was never used...
- Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu
parameter instead
- Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
- Remove prototypes without implementations
RISC-V:
- Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
- Added ONE_REG interface for SATP mode
- Added ONE_REG interface to enable/disable multiple ISA extensions
- Improved error codes returned by ONE_REG interfaces
- Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
- Added get-reg-list selftest for KVM RISC-V
s390:
- PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
- Guest debug fixes (Ilya)
x86:
- Clean up KVM's handling of Intel architectural events
- Intel bugfixes
- Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use
debug registers and generate/handle #DBs
- Clean up LBR virtualization code
- Fix a bug where KVM fails to set the target pCPU during an IRTE
update
- Fix fatal bugs in SEV-ES intrahost migration
- Fix a bug where the recent (architecturally correct) change to
reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to
skip it)
- Retry APIC map recalculation if a vCPU is added/enabled
- Overhaul emergency reboot code to bring SVM up to par with VMX, tie
the "emergency disabling" behavior to KVM actually being loaded,
and move all of the logic within KVM
- Fix user triggerable WARNs in SVM where KVM incorrectly assumes the
TSC ratio MSR cannot diverge from the default when TSC scaling is
disabled up related code
- Add a framework to allow "caching" feature flags so that KVM can
check if the guest can use a feature without needing to search
guest CPUID
- Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
- Fix KVM's handling of !visible guest roots to avoid premature
triple fault injection
- Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the
API surface that is needed by external users (currently only
KVMGT), and fix a variety of issues in the process
Generic:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier
events to pass action specific data without needing to constantly
update the main handlers.
- Drop unused function declarations
Selftests:
- Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
- Add support for printf() in guest code and covert all guest asserts
to use printf-based reporting
- Clean up the PMU event filter test and add new testcases
- Include x86 selftests in the KVM x86 MAINTAINERS entry"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits)
KVM: x86/mmu: Include mmu.h in spte.h
KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots
KVM: x86/mmu: Disallow guest from using !visible slots for page tables
KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page
KVM: x86/mmu: Harden new PGD against roots without shadow pages
KVM: x86/mmu: Add helper to convert root hpa to shadow page
drm/i915/gvt: Drop final dependencies on KVM internal details
KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers
KVM: x86/mmu: Drop @slot param from exported/external page-track APIs
KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled
KVM: x86/mmu: Assert that correct locks are held for page write-tracking
KVM: x86/mmu: Rename page-track APIs to reflect the new reality
KVM: x86/mmu: Drop infrastructure for multiple page-track modes
KVM: x86/mmu: Use page-track notifiers iff there are external users
KVM: x86/mmu: Move KVM-only page-track declarations to internal header
KVM: x86: Remove the unused page-track hook track_flush_slot()
drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region()
KVM: x86: Add a new page-track hook to handle memslot deletion
drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot
KVM: x86: Reject memslot MOVE operations if KVMGT is attached
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- A couple of virtual vs physical address confusion fixes
- Rework locking in dcssblk driver to address a lockdep warning
- Remove support for "noexec" kernel command line option since there is
no use case where it would make sense
- Simplify kernel mapping setup and get rid of quite a bit of code
- Add architecture specific __set_memory_yy() functions which allow us
to modify kernel mappings. Unlike the set_memory_xx() variants they
take void pointer start and end parameters, which allows using them
without the usual casts, and also to use them on areas larger than
8TB.
Note that the set_memory_xx() family comes with an int num_pages
parameter which overflows with 8TB. This could be addressed by
changing the num_pages parameter to unsigned long, however requires
to change all architectures, since the module code expects an int
parameter (see module_set_memory()).
This was indeed an issue since for debug_pagealloc() we call
set_memory_4k() on the whole identity mapping. Therefore address this
for now with the __set_memory_yy() variant, and address common code
later
- Use dev_set_name() and also fix memory leak in zcrypt driver error
handling
- Remove unused lsi_mask from airq_struct
- Add warning for invalid kernel mapping requests
* tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vmem: do not silently ignore mapping limit
s390/zcrypt: utilize dev_set_name() ability to use a formatted string
s390/zcrypt: don't leak memory if dev_set_name() fails
s390/mm: fix MAX_DMA_ADDRESS physical vs virtual confusion
s390/airq: remove lsi_mask from airq_struct
s390/mm: use __set_memory() variants where useful
s390/set_memory: add __set_memory() variant
s390/set_memory: generate all set_memory() functions
s390/mm: improve description of mapping permissions of prefix pages
s390/amode31: change type of __samode31, __eamode31, etc
s390/mm: simplify kernel mapping setup
s390: remove "noexec" option
s390/vmem: fix virtual vs physical address confusion
s390/dcssblk: fix lockdep warning
s390/monreader: fix virtual vs physical address confusion
|
|
Pull MIPS updates from Thomas Bogendoerfer:
"Just cleanups and fixes"
* tag 'mips_6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: TXx9: Do PCI error checks on own line
arch/mips/configs/*_defconfig cleanup
MIPS: VDSO: Conditionally export __vdso_gettimeofday()
Mips: loongson3_defconfig: Enable ast drm driver by default
mips: remove <asm/export.h>
mips: replace #include <asm/export.h> with #include <linux/export.h>
mips: remove unneeded #include <asm/export.h>
MIPS: Loongson64: Fix more __iomem attributes
MIPS: loongson32: Remove regs-rtc.h
MIPS: loongson32: Remove regs-clk.h
MIPS: More explicit DT include clean-ups
MIPS: Fixup explicit DT include clean-up
Revert MIPS: Loongson: Fix build error when make modules_install
MIPS: Only fiddle with CHECKFLAGS if `need-compiler'
MIPS: Fix CONFIG_CPU_DADDI_WORKAROUNDS `modules_install' regression
MIPS: Explicitly include correct DT includes
|
|
Pull ceph updates from Ilya Dryomov:
"Mixed with some fixes and cleanups, this brings in reasonably complete
fscrypt support to CephFS! The list of things which don't work with
encryption should be fairly short, mostly around the edges: fallocate
(not supported well in CephFS to begin with), copy_file_range
(requires re-encryption), non-default striping patterns.
This was a multi-year effort principally by Jeff Layton with
assistance from Xiubo Li, Luís Henriques and others, including several
dependant changes in the MDS, netfs helper library and fscrypt
framework itself"
* tag 'ceph-for-6.6-rc1' of https://github.com/ceph/ceph-client: (53 commits)
ceph: make num_fwd and num_retry to __u32
ceph: make members in struct ceph_mds_request_args_ext a union
rbd: use list_for_each_entry() helper
libceph: do not include crypto/algapi.h
ceph: switch ceph_lookup/atomic_open() to use new fscrypt helper
ceph: fix updating i_truncate_pagecache_size for fscrypt
ceph: wait for OSD requests' callbacks to finish when unmounting
ceph: drop messages from MDS when unmounting
ceph: update documentation regarding snapshot naming limitations
ceph: prevent snapshot creation in encrypted locked directories
ceph: add support for encrypted snapshot names
ceph: invalidate pages when doing direct/sync writes
ceph: plumb in decryption during reads
ceph: add encryption support to writepage and writepages
ceph: add read/modify/write to ceph_sync_write
ceph: align data in pages in ceph_sync_write
ceph: don't use special DIO path for encrypted inodes
ceph: add truncate size handling support for fscrypt
ceph: add object version support for sync read
libceph: allow ceph_osdc_new_request to accept a multi-op read
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for Azoteq IQS7210A/7211A/E touch controllers
- support for Azoteq IQS7222D variant added to iqs7222 driver
- support for touch keys functionality added to Melfas MMS114 driver
- new hardware IDs added to exc3000 and Goodix drivers
- xpad driver gained support for GameSir T4 Kaleid Controller
- a fix for xpad driver to properly support some third-party
controllers that need a magic packet to start properly
- a fix for psmouse driver to more reliably switch to RMI4 mode on
devices that use native RMI4/SMbus protocol
- a quirk for i8042 for TUXEDO Gemini 17 Gen1/Clevo PD70PN laptops
- multiple drivers have been updated to make use of devm and other
newer APIs such as dev_err_probe(), devm_regulator_get_enable(), and
others.
* tag 'input-for-v6.6-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (83 commits)
Input: goodix - add support for ACPI ID GDX9110
Input: rpckbd - fix the return value handle for platform_get_irq()
Input: tca6416-keypad - switch to using input core's polling features
Input: tca6416-keypad - convert to use devm_* api
Input: tca6416-keypad - fix interrupt enable disbalance
Input: tca6416-keypad - rely on I2C core to set up suspend/resume
Input: tca6416-keypad - always expect proper IRQ number in i2c client
Input: lm8323 - convert to use devm_* api
Input: lm8323 - rely on device core to create kp_disable attribute
Input: qt2160 - convert to use devm_* api
Input: qt2160 - do not hard code interrupt trigger
Input: qt2160 - switch to using threaded interrupt handler
Input: qt2160 - tweak check for i2c adapter functionality
Input: psmouse - add delay when deactivating for SMBus mode
Input: mcs-touchkey - fix uninitialized use of error in mcs_touchkey_probe()
Input: qt1070 - convert to use devm_* api
Input: mcs-touchkey - convert to use devm_* api
Input: amikbd - convert to use devm_* api
Input: lm8333 - convert to use devm_* api
Input: mms114 - add support for touch keys
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add marvell GTI watchdog driver
- add support for Amlogic-T7 SoCs
- document the IPQ5018 watchdog compatible
- enable COMPILE_TEST for more watchdog device drivers
- core: stop watchdog when executing poweroff command
- other small improvements and fixes
* tag 'linux-watchdog-6.6-rc1' of git://www.linux-watchdog.org/linux-watchdog: (21 commits)
watchdog: Add support for Amlogic-T7 SoCs
watchdog: Add a new struct for Amlogic-GXBB driver
dt-bindings: watchdog: Add support for Amlogic-T7 SoCs
dt-bindings: watchdog: qcom-wdt: document IPQ5018
watchdog: imx2_wdt: Improve dev_crit() message
watchdog: stm32: Drop unnecessary of_match_ptr()
watchdog: sama5d4: readout initial state
watchdog: intel-mid_wdt: add MODULE_ALIAS() to allow auto-load
watchdog: core: stop watchdog when executing poweroff command
watchdog: pm8916_wdt: Remove redundant of_match_ptr()
watchdog: xilinx_wwdt: Use div_u64() in xilinx_wwdt_start()
watchdog: starfive: Remove #ifdef guards for PM related functions
watchdog: s3c2410: Fix potential deadlock on &wdt->lock
watchdog:rit_wdt: Add support for WDIOF_CARDRESET
dt-bindings: watchdog: ti,rti-wdt: Add support for WDIOF_CARDRESET
watchdog: Enable COMPILE_TEST for more drivers
watchdog: advantech_ec_wdt: fix Kconfig dependencies
watchdog: Explicitly include correct DT includes
Watchdog: Add marvell GTI watchdog driver
dt-bindings: watchdog: marvell GTI system watchdog driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Ensure correct includes are present and remove some that are not
required
- Drop redundant of_match_ptr() call to cast pointer to NULL
Bug Fixes:
- Revert to old (expected) behaviour of initialising PWM state on
first brightness change
- Correctly handle / propagate errors
- Fix 'sometimes-uninitialised' issues"
* tag 'backlight-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: led_bl: Remove redundant of_match_ptr()
backlight: lp855x: Drop ret variable in brightness change function
backlight: gpio_backlight: Drop output GPIO direction check for initial power state
backlight: lp855x: Catch errors when changing brightness
backlight: lp855x: Initialize PWM state on first brightness change
backlight: qcom-wled: Explicitly include correct DT includes
|
|
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Random kernel crash detected in TI CICD when regulator driver is added.
This is root caused to irq index increment being done twice causing
irq_data being allocated outside of the range.
- Rework tps6594_request_reg_irqs with correct index increment
- Adjust irq_data kmalloc size to the exact size needed for the device
This has been reported on TI mainline. No public bug report associated.
Reported-by: Udit Kumar <u-kumar1@ti.com>
Fixes: f17ccc5deb4d ("regulator: tps6594-regulator: Add driver for TI TPS6594 regulators")
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20230828-tps6594_random_boot_crash_fix-v1-1-f29cbf9ddb37@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Fix OF include file for ata platform drivers (Rob)
- Simplify various ahci, sata and pata platform drivers using the
function devm_platform_ioremap_resource() (Yangtao)
- Cleanup libata time related argument types (e.g. timeouts values)
(Sergey)
- Cleanup libata code around error handling as all ata drivers now
define a error_handler operation (Hannes and Niklas)
- Remove functions intended for libsas that are in fact unused (Niklas)
- Change the remove device callback of platform drivers to a null
function (Uwe)
- Simplify the pata_imx driver using devm_clk_get_enabled() (Li)
- Remove old and uinused remnants of the ide code in arm, parisc,
powerpc, sparc and m68k architectures and associated drivers
(pata_buddha, pata_falcon and pata_gayle) (Geert)
- Add missing MODULE_DESCRIPTION() in the sata_gemini and pata_ftide010
drivers (me)
- Several fixes for the pata_ep93xx and pata_falcon drivers (Nikita,
Michael)
- Add Elkhart Lake AHCI controller support to the ahci driver (Werner)
- Disable NCQ trim on Micron 1100 drives (Pawel)
* tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (60 commits)
ata: libata-core: Disable NCQ_TRIM on Micron 1100 drives
ata: ahci: Add Elkhart Lake AHCI controller
ata: pata_falcon: add data_swab option to byte-swap disk data
ata: pata_falcon: fix IO base selection for Q40
ata: pata_ep93xx: use soc_device_match for UDMA modes
ata: pata_ep93xx: fix error return code in probe
ata: sata_gemini: Add missing MODULE_DESCRIPTION
ata: pata_ftide010: Add missing MODULE_DESCRIPTION
m68k: Remove <asm/ide.h>
ata: pata_gayle: Remove #include <asm/ide.h>
ata: pata_falcon: Remove #include <asm/ide.h>
ata: pata_buddha: Remove #include <asm/ide.h>
asm-generic: Remove ide_iops.h
sparc: Remove <asm/ide.h>
powerpc: Remove <asm/ide.h>
parisc: Remove <asm/ide.h>
ARM: Remove <asm/ide.h>
ata: pata_imx: Use helper function devm_clk_get_enabled()
ata: sata_rcar: Convert to platform remove callback returning void
ata: sata_mv: Convert to platform remove callback returning void
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- qcom: fix incorrect num_chans counting
- mhu: Remove redundant dev_err
- bcm: fix comments
- common changes:
- convert to use devm_platform_get_and_ioremap_resource
- correct DT includes
* tag 'mailbox-v6.6' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: qcom-ipcc: fix incorrect num_chans counting
mailbox: Explicitly include correct DT includes
mailbox: ti-msgmgr: Use devm_platform_ioremap_resource_byname()
mailbox: platform-mhu: Remove redundant dev_err()
mailbox: bcm-pdc: Fix some kernel-doc comments
mailbox: mailbox-test: Fix an error check in mbox_test_probe()
mailbox: tegra-hsp: Convert to devm_platform_ioremap_resource()
mailbox: rockchip: Use devm_platform_get_and_ioremap_resource()
mailbox: mailbox-test: Use devm_platform_get_and_ioremap_resource()
mailbox: bcm-pdc: Use devm_platform_get_and_ioremap_resource()
mailbox: bcm-ferxrm-mailbox: Use devm_platform_get_and_ioremap_resource()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull more tpm updates from Jarkko Sakkinen:
"Two more bug fixes for tpm_crb, categorically disabling rng for AMD
CPU's in the tpm_crb driver, discarding the earlier probing approach"
* tag 'tpmdd-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Enable hwrng only for Pluton on AMD CPUs
tpm_crb: Fix an error handling path in crb_acpi_add()
|
|
With the dev_set_name() prototype it's not obvious that it takes
a formatted string as a parameter. Use its facility instead of
duplicating the same with strncpy()/snprintf() calls.
With this, also prevent return error code to be shadowed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230831110000.24279-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
When dev_set_name() fails, zcdn_create() doesn't free the newly
allocated resources. Do it.
Fixes: 00fab2350e6b ("s390/zcrypt: multiple zcrypt device nodes support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230831110000.24279-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Breaking out early when a match is found leads to an incorrect num_chans
value when more than one ipcc mailbox channel is used by the same device.
Fixes: e9d50e4b4d04 ("mailbox: qcom-ipcc: Dynamic alloc for channel arrangement")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert platform_get_resource_byname() + devm_ioremap_resource() to a
single call to devm_platform_ioremap_resource_byname(), as this is
exactly what this function does.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
There is no need to call the dev_err() function directly to print a custom
message when handling an error from platform_get_irq() function as
it is going to display an appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Fix some kernel-doc comments to silence the warnings:
drivers/mailbox/bcm-pdc-mailbox.c:707: warning: Function parameter or member 'pdcs' not described in 'pdc_tx_list_sg_add'
drivers/mailbox/bcm-pdc-mailbox.c:707: warning: Excess function parameter 'spu_idx' description in 'pdc_tx_list_sg_add'
drivers/mailbox/bcm-pdc-mailbox.c:875: warning: Function parameter or member 'pdcs' not described in 'pdc_rx_list_sg_add'
drivers/mailbox/bcm-pdc-mailbox.c:875: warning: Excess function parameter 'spu_idx' description in 'pdc_rx_list_sg_add'
drivers/mailbox/bcm-pdc-mailbox.c:966: warning: Function parameter or member 't' not described in 'pdc_tasklet_cb'
drivers/mailbox/bcm-pdc-mailbox.c:966: warning: Excess function parameter 'data' description in 'pdc_tasklet_cb'
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
mbox_test_request_channel() function returns NULL or
error value embedded in the pointer (PTR_ERR).
Evaluate the return value using IS_ERR_OR_NULL.
Signed-off-by: Minjie Du <duminjie@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix cpufreq core and the pcc cpufreq driver, add per-policy
boost support to cpufreq and add Georgian translation Makefile
LANGUAGES in cpupower.
Specifics:
- Add Georgian translation to Makefile LANGUAGES in cpupower (Shuah
Khan).
- Add support for per-policy performance boost to cpufreq (Jie Zhan).
- Fix assorted issues in the cpufreq core, common governor code and
in the pcc cpufreq driver (Liao Chang)"
* tag 'pm-6.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Support per-policy performance boost
cpufreq: pcc: Fix the potentinal scheduling delays in target_index()
cpufreq: governor: Free dbs_data directly when gov->init() fails
cpufreq: Fix the race condition while updating the transition_task of policy
cpufreq: Avoid printing kernel addresses in cpufreq_resume()
cpupower: Add Georgian translation to Makefile LANGUAGES
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These are mostly updates of thermal control drivers for ARM platforms,
new thermal control support for Loongson-2 and a couple of core
cleanups made possible by recent changes merged previously.
Specifics:
- Check if the Tegra BPMP supports the trip points in order to set
the .set_trips callback (Mikko Perttunen)
- Add new Loongson-2 thermal sensor along with the DT bindings (Yinbo
Zhu)
- Use IS_ERR_OR_NULL() helper to replace a double test on the TI
bandgap sensor (Li Zetao)
- Remove redundant platform_set_drvdata() calls, as there are no
corresponding calls to platform_get_drvdata(), from a bunch of
drivers (Andrei Coardos)
- Switch the Mediatek LVTS mode to filtered in order to enable
interrupts (Nícolas F. R. A. Prado)
- Fix Wvoid-pointer-to-enum-cast warning on the Exynos TMU (Krzysztof
Kozlowski)
- Remove redundant dev_err_probe(), because the underlying function
already called it, from the Mediatek sensor (Chen Jiahao)
- Free calibration nvmem after reading it on sun8i (Mark Brown)
- Remove useless comment from the sun8i driver (Yangtao Li)
- Make tsens_xxxx_nvmem static to fix a sparse warning on QCom tsens
(Min-Hua Chen)
- Remove error message at probe deferral on imx8mm (Ahmad Fatoum)
- Fix parameter check in lvts_debugfs_init() with IS_ERR() on
Mediatek LVTS (Minjie Du)
- Fix interrupt routine and configuratoin for Mediatek LVTS (Nícolas
F. R. A. Prado)
- Drop unused .get_trip_type(), .get_trip_temp() and .get_trip_hyst()
thermal zone callbacks from the core and rework the .get_trend()
one to take a trip point pointer as an argument (Rafael Wysocki)"
* tag 'thermal-6.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (29 commits)
thermal: core: Rework .get_trend() thermal zone callback
thermal: core: Drop unused .get_trip_*() callbacks
thermal/drivers/tegra-bpmp: Check if BPMP supports trip points
thermal: dt-bindings: add loongson-2 thermal
thermal/drivers/loongson-2: Add thermal management support
thermal/drivers/ti-soc-thermal: Use helper function IS_ERR_OR_NULL()
thermal/drivers/generic-adc: Removed unneeded call to platform_set_drvdata()
thermal/drivers/max77620_thermal: Removed unneeded call to platform_set_drvdata()
thermal/drivers/mediatek/auxadc_thermal: Removed call to platform_set_drvdata()
thermal/drivers/sun8i_thermal: Remove unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/brcstb_thermal: Removed unneeded platform_set_drvdata()
thermal/drivers/mediatek/lvts_thermal: Make readings valid in filtered mode
thermal/drivers/k3_bandgap: Remove unneeded call to platform_set_drvdata()
thermal/drivers/k3_j72xx_bandgap: Removed unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/sr-thermal: Removed call to platform_set_drvdata()
thermal/drivers/samsung: Fix Wvoid-pointer-to-enum-cast warning
thermal/drivers/db8500: Remove redundant of_match_ptr()
thermal/drivers/mediatek: Clean up redundant dev_err_probe()
thermal/drivers/sun8i: Free calibration nvmem after reading it
thermal/drivers/sun8i: Remove unneeded comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"Support for booting the iMX remoteprocs using MMIO, instead of SMCCC
is added. The iMX driver is also extended to support delivering
interrupts from an arbitrary number of vdev.
Support is added to the TI PRU driver, to allow GPMUX to be controlled
from DeviceTree.
The Qualcomm coredump collector is extended to fall back to generating
a full coredump, in the case that the loaded firmware doesn't support
generating minidump. The overly terse MD abbreviation of "MINIDUMP" is
expanded, to make the code easier on the eye.
The list of Qualcomm Sensor Low Power Island (SLPI) instances
supported is cleaned up, and SDM845 is added. SDM630/636/660 support
for the modem subsystem (mss) is added.
All the Qualcomm drivers are transitioned to of_reserved_mem_lookup()
instead of open coding the resolution of reserved-memory regions, to
gain handling of error cases. A couple of drivers are transitioned to
use devm_platform_ioremap_resource_byname().
The stm32 remoteproc driver's PM operations are updated to modern
macros, to avoid the "unused variable"-warning in some configurations.
Drivers are transitioned away from directly including of_device.h"
* tag 'rproc-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (23 commits)
remoteproc: pru: add support for configuring GPMUX based on client setup
remoteproc: stm32: fix incorrect optional pointers
remoteproc: imx_rproc: Switch iMX8MN/MP from SMCCC to MMIO
dt-bindings: remoteproc: imx_rproc: Support i.MX8MN/P MMIO
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Fix 8996 clocks
remoteproc: qcom: pas: add SDM845 SLPI compatible
remoteproc: qcom: q6v5-mss: Add support for SDM630/636/660
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Add SDM660 compatible
remoteproc: qcom: Expand MD_* as MINIDUMP_*
remoteproc: qcom: pas: refactor SLPI remoteproc init
dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible
remoteproc: qcom: wcnss: use devm_platform_ioremap_resource_byname()
remoteproc: qcom: q6v5: use devm_platform_ioremap_resource_byname()
dt-bindings: remoteproc: qcom: sm6115-pas: Add QCM2290
remoteproc: qcom: Add full coredump fallback mechanism
remoteproc: core: Export the rproc coredump APIs
remoteproc: qcom: Use of_reserved_mem_lookup()
remoteproc: imx_rproc: iterate all notifiyids in rx callback
dt-bindings: remoteproc: qcom,adsp: bring back firmware-name
dt-bindings: remoteproc: qcom,sm8550-pas: require memory-region
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull rpmsg updates from Bjorn Andersson:
"Add support for the GLINK flow control signals, and expose this to the
user through the rpmsg_char interface. Add missing kstrdup() failure
handling during allocation of GLINK channel objects"
* tag 'rpmsg-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: glink: Avoid dereferencing NULL channel
rpmsg: glink: Add check for kstrdup
rpmsg: char: Add RPMSG GET/SET FLOWCONTROL IOCTL support
rpmsg: glink: Add support to handle signals command
rpmsg: core: Add signal API support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull hwspinlock updates from Bjorn Andersson:
"Convert u8500 and omap drivers to void-returning remove.
Complete the support for representing the Qualcomm TCSR mutex as a
mmio device, and check the return value of devm_regmap_field_alloc()
in the same"
* tag 'hwlock-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
hwspinlock: qcom: add missing regmap config for SFPB MMIO implementation
hwspinlock: u8500: Convert to platform remove callback returning void
hwspinlock: omap: Convert to platform remove callback returning void
hwspinlock: omap: Emit only one error message for errors in .remove()
hwspinlock: add a check of devm_regmap_field_alloc in qcom_hwspinlock_probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add new framework to support Group Multi-Color (GMC) LEDs
- Offer an 'optional' API for non-essential LEDs
- Support obtaining 'max brightness' values from Device Tree
- Provide new led_classdev member 'color' (settable via DT and SYFS)
- Stop TTY Trigger from using the old LED_ON constraints
- Statically allocate leds_class
New Drivers:
- Add support for NXP PCA995x I2C Constant Current LED Driver
New Device Support:
- Add support for Siemens Simatic IPC BX-21 to Simatic IPC
Fix-ups:
- Some dependency / Kconfig tweaking
- Move final probe() functions back over from .probe_new()
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Fix trivial styling issues; comments
- Ensure correct includes are present and remove some that are not
required
- Omit the use of redundant casts and if relevant replace with better
ones
- Use purpose-built APIs for various actions; sysfs_emit(),
module_led_trigger()
- Remove a bunch of superfluous locking
Bug Fixes:
- Ensure error codes are correctly propagated back up the call chain
- Fix incorrect error values from being returned (missing '-')
- Ensure get'ed resources are put'ed to prevent leaks
- Use correct class when exporting module resources
- Fixing rounding (or lack there of) issues
- Fix 'always false' LED_COLOR_ID_MULTI BUG() check"
* tag 'leds-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (40 commits)
leds: aw2013: Enable pull-up supply for interrupt and I2C
dt-bindings: leds: Document pull-up supply for interrupt and I2C
dt-bindings: leds: aw2013: Document interrupt
leds: uleds: Use module_misc_device macro to simplify the code
leds: trigger: netdev: Use module_led_trigger macro to simplify the code
dt-bindings: leds: Fix reference to definition of default-state
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: Make leds_class a static const structure
leds: Remove redundant of_match_ptr()
dt-bindings: leds: Add gpio-line-names to PCA9532 GPIO
leds: trigger: tty: Do not use LED_ON/OFF constants, use led_blink_set_oneshot instead
dt-bindings: leds: rohm,bd71828: Drop select:false
leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false
leds: multicolor: Use rounded division when calculating color components
leds: rgb: Add a multicolor LED driver to group monochromatic LEDs
dt-bindings: leds: Add binding for a multicolor group of LEDs
leds: class: Store the color index in struct led_classdev
leds: Provide devm_of_led_get_optional()
leds: pca995x: Fix MODULE_DEVICE_TABLE for OF
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull NFD updates from Lee Jones:
"New Drivers:
- Add support for the Cirrus Logic CS42L43 Audio CODEC
Fix-ups:
- Make use of specific printk() format tags for various optimisations
- Kconfig / module modifications / tweaking
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Convert a bunch of Regmap configurations to use the Maple Tree
cache
- Ensure correct includes are present and remove some that are not
required
- Remove superfluous code
- Reduce amount of cycles spent in critical sections
- Omit the use of redundant casts and if relevant replace with better
ones
- Swap out raw_spin_{un}lock_irq{save,restore}() for
spin_{un}lock_irq{save,restore}()
Bug Fixes:
- Repair theoretical deadlock situation
- Fix some link-time dependencies
- Use more appropriate datatype when casting"
* tag 'mfd-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (70 commits)
mfd: mc13xxx: Simplify device data fetching in probe()
mfd: rz-mtu3: Replace raw_spin_lock->spin_lock()
mfd: rz-mtu3: Reduce critical sections
mfd: mxs-lradc: Fix Wvoid-pointer-to-enum-cast warning
mfd: wm31x: Fix Wvoid-pointer-to-enum-cast warning
mfd: wm8994: Fix Wvoid-pointer-to-enum-cast warning
mfd: tc3589: Fix Wvoid-pointer-to-enum-cast warning
mfd: lp87565: Fix Wvoid-pointer-to-enum-cast warning
mfd: hi6421-pmic: Fix Wvoid-pointer-to-enum-cast warning
mfd: max77541: Fix Wvoid-pointer-to-enum-cast warning
mfd: max14577: Fix Wvoid-pointer-to-enum-cast warning
mfd: stmpe: Fix Wvoid-pointer-to-enum-cast warning
mfd: rn5t618: Remove redundant of_match_ptr()
mfd: lochnagar-i2c: Remove redundant of_match_ptr()
mfd: stpmic1: Remove redundant of_match_ptr()
mfd: act8945a: Remove redundant of_match_ptr()
mfd: rsmu_spi: Remove redundant of_match_ptr()
mfd: altera-a10sr: Remove redundant of_match_ptr()
mfd: rsmu_i2c: Remove redundant of_match_ptr()
mfd: tc3589x: Remove redundant of_match_ptr()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource/clockevent driver updates from Thomas Gleixner:
- Remove the OXNAS driver instead of adding a new one!
- A set of boring fixes, cleanups and improvements
* tag 'timers-core-2023-09-04-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Explicitly include correct DT includes
clocksource/drivers/sun5i: Convert to platform device driver
clocksource/drivers/sun5i: Remove pointless struct
clocksource/drivers/sun5i: Remove duplication of code and data
clocksource/drivers/loongson1: Set variable ls1x_timer_lock storage-class-specifier to static
clocksource/drivers/arm_arch_timer: Disable timer before programming CVAL
dt-bindings: timer: oxsemi,rps-timer: remove obsolete bindings
clocksource/drivers/timer-oxnas-rps: Remove obsolete timer driver
|
|
The vendor check introduced by commit 554b841d4703 ("tpm: Disable RNG for
all AMD fTPMs") doesn't work properly on a number of Intel fTPMs. On the
reported systems the TPM doesn't reply at bootup and returns back the
command code. This makes the TPM fail probe on Lenovo Legion Y540 laptop.
Since only Microsoft Pluton is the only known combination of AMD CPU and
fTPM from other vendor, disable hwrng otherwise. In order to make sysadmin
aware of this, print also info message to the klog.
Cc: stable@vger.kernel.org
Fixes: 554b841d4703 ("tpm: Disable RNG for all AMD fTPMs")
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217804
Reported-by: Patrick Steinhardt <ps@pks.im>
Reported-by: Raymond Jay Golo <rjgolo@gmail.com>
Reported-by: Ronan Pigott <ronan@rjp.ie>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Some error paths don't call acpi_put_table() before returning.
Branch to the correct place instead of doing some direct return.
Fixes: 4d2732882703 ("tpm_crb: Add support for CRB devices based on Pluton")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Matthew Garrett <mgarrett@aurora.tech>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Support for SEV-SNP guests on Hyper-V (Tianyu Lan)
- Support for TDX guests on Hyper-V (Dexuan Cui)
- Use SBRM API in Hyper-V balloon driver (Mitchell Levy)
- Avoid dereferencing ACPI root object handle in VMBus driver (Maciej
Szmigiero)
- A few misecllaneous fixes (Jiapeng Chong, Nathan Chancellor, Saurabh
Sengar)
* tag 'hyperv-next-signed-20230902' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (24 commits)
x86/hyperv: Remove duplicate include
x86/hyperv: Move the code in ivm.c around to avoid unnecessary ifdef's
x86/hyperv: Remove hv_isolation_type_en_snp
x86/hyperv: Use TDX GHCI to access some MSRs in a TDX VM with the paravisor
Drivers: hv: vmbus: Bring the post_msg_page back for TDX VMs with the paravisor
x86/hyperv: Introduce a global variable hyperv_paravisor_present
Drivers: hv: vmbus: Support >64 VPs for a fully enlightened TDX/SNP VM
x86/hyperv: Fix serial console interrupts for fully enlightened TDX guests
Drivers: hv: vmbus: Support fully enlightened TDX guests
x86/hyperv: Support hypercalls for fully enlightened TDX guests
x86/hyperv: Add hv_isolation_type_tdx() to detect TDX guests
x86/hyperv: Fix undefined reference to isolation_type_en_snp without CONFIG_HYPERV
x86/hyperv: Add missing 'inline' to hv_snp_boot_ap() stub
hv: hyperv.h: Replace one-element array with flexible-array member
Drivers: hv: vmbus: Don't dereference ACPI root object handle
x86/hyperv: Add hyperv-specific handling for VMMCALL under SEV-ES
x86/hyperv: Add smp support for SEV-SNP guest
clocksource: hyper-v: Mark hyperv tsc page unencrypted in sev-snp enlightened guest
x86/hyperv: Use vmmcall to implement Hyper-V hypercall in sev-snp enlightened guest
drivers: hv: Mark percpu hvcall input arg page unencrypted in SEV-SNP enlightened guest
...
|
|
Pull virtio updates from Michael Tsirkin:
"A small pull request this time around, mostly because the vduse
network got postponed to next relase so we can be sure we got the
security store right"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: fix avail_wrap_counter in virtqueue_add_packed
virtio_vdpa: build affinity masks conditionally
virtio_net: merge dma operations when filling mergeable buffers
virtio_ring: introduce dma sync api for virtqueue
virtio_ring: introduce dma map api for virtqueue
virtio_ring: introduce virtqueue_reset()
virtio_ring: separate the logic of reset/enable from virtqueue_resize
virtio_ring: correct the expression of the description of virtqueue_resize()
virtio_ring: skip unmap for premapped
virtio_ring: introduce virtqueue_dma_dev()
virtio_ring: support add premapped buf
virtio_ring: introduce virtqueue_set_dma_premapped()
virtio_ring: put mapping error check in vring_map_one_sg
virtio_ring: check use_dma_api before unmap desc for indirect
vdpa_sim: offer VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK
vdpa: add get_backend_features vdpa operation
vdpa: accept VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK backend feature
vdpa: add VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK flag
vdpa/mlx5: Remove unused function declarations
|
|
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-3-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Through empirical testing it has been determined that sometimes RX SPI
transfers with DMA enabled return corrupted data. This is down to single
or even multiple bytes lost during DMA transfer from SPI peripheral to
memory. It seems the RX FIFO within the SPI peripheral can become
confused when performing bus read accesses wider than a single byte to it
during an active SPI transfer.
This patch reduces the width of individual DMA read accesses to the
RX FIFO to a single byte to mitigate that issue.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-2-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In current packed virtqueue implementation, the avail_wrap_counter won't
flip, in the case when the driver supplies a descriptor chain with a
length equals to the queue size; total_sg == vq->packed.vring.num.
Let’s assume the following situation:
vq->packed.vring.num=4
vq->packed.next_avail_idx: 1
vq->packed.avail_wrap_counter: 0
Then the driver adds a descriptor chain containing 4 descriptors.
We expect the following result with avail_wrap_counter flipped:
vq->packed.next_avail_idx: 1
vq->packed.avail_wrap_counter: 1
But, the current implementation gives the following result:
vq->packed.next_avail_idx: 1
vq->packed.avail_wrap_counter: 0
To reproduce the bug, you can set a packed queue size as small as
possible, so that the driver is more likely to provide a descriptor
chain with a length equal to the packed queue size. For example, in
qemu run following commands:
sudo qemu-system-x86_64 \
-enable-kvm \
-nographic \
-kernel "path/to/kernel_image" \
-m 1G \
-drive file="path/to/rootfs",if=none,id=disk \
-device virtio-blk,drive=disk \
-drive file="path/to/disk_image",if=none,id=rwdisk \
-device virtio-blk,drive=rwdisk,packed=on,queue-size=4,\
indirect_desc=off \
-append "console=ttyS0 root=/dev/vda rw init=/bin/bash"
Inside the VM, create a directory and mount the rwdisk device on it. The
rwdisk will hang and mount operation will not complete.
This commit fixes the wrap counter error by flipping the
packed.avail_wrap_counter, when start of descriptor chain equals to the
end of descriptor chain (head == i).
Fixes: 1ce9e6055fa0 ("virtio_ring: introduce packed ring support")
Signed-off-by: Yuan Yao <yuanyaogoog@chromium.org>
Message-Id: <20230808051110.3492693-1-yuanyaogoog@chromium.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We try to build affinity mask via create_affinity_masks()
unconditionally which may lead several issues:
- the affinity mask is not used for parent without affinity support
(only VDUSE support the affinity now)
- the logic of create_affinity_masks() might not work for devices
other than block. For example it's not rare in the networking device
where the number of queues could exceed the number of CPUs. Such
case breaks the current affinity logic which is based on
group_cpus_evenly() who assumes the number of CPUs are not less than
the number of groups. This can trigger a warning[1]:
if (ret >= 0)
WARN_ON(nr_present + nr_others < numgrps);
Fixing this by only build the affinity masks only when
- Driver passes affinity descriptor, driver like virtio-blk can make
sure to limit the number of queues when it exceeds the number of CPUs
- Parent support affinity setting config ops
This help to avoid the warning. More optimizations could be done on
top.
[1]
[ 682.146655] WARNING: CPU: 6 PID: 1550 at lib/group_cpus.c:400 group_cpus_evenly+0x1aa/0x1c0
[ 682.146668] CPU: 6 PID: 1550 Comm: vdpa Not tainted 6.5.0-rc5jason+ #79
[ 682.146671] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[ 682.146673] RIP: 0010:group_cpus_evenly+0x1aa/0x1c0
[ 682.146676] Code: 4c 89 e0 5b 5d 41 5c 41 5d 41 5e c3 cc cc cc cc e8 1b c4 74 ff 48 89 ef e8 13 ac 98 ff 4c 89 e7 45 31 e4 e8 08 ac 98 ff eb c2 <0f> 0b eb b6 e8 fd 05 c3 00 45 31 e4 eb e5 cc cc cc cc cc cc cc cc
[ 682.146679] RSP: 0018:ffffc9000215f498 EFLAGS: 00010293
[ 682.146682] RAX: 000000000001f1e0 RBX: 0000000000000041 RCX: 0000000000000000
[ 682.146684] RDX: ffff888109922058 RSI: 0000000000000041 RDI: 0000000000000030
[ 682.146686] RBP: ffff888109922058 R08: ffffc9000215f498 R09: ffffc9000215f4a0
[ 682.146687] R10: 00000000000198d0 R11: 0000000000000030 R12: ffff888107e02800
[ 682.146689] R13: 0000000000000030 R14: 0000000000000030 R15: 0000000000000041
[ 682.146692] FS: 00007fef52315740(0000) GS:ffff888237380000(0000) knlGS:0000000000000000
[ 682.146695] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 682.146696] CR2: 00007fef52509000 CR3: 0000000110dbc004 CR4: 0000000000370ee0
[ 682.146698] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 682.146700] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 682.146701] Call Trace:
[ 682.146703] <TASK>
[ 682.146705] ? __warn+0x7b/0x130
[ 682.146709] ? group_cpus_evenly+0x1aa/0x1c0
[ 682.146712] ? report_bug+0x1c8/0x1e0
[ 682.146717] ? handle_bug+0x3c/0x70
[ 682.146721] ? exc_invalid_op+0x14/0x70
[ 682.146723] ? asm_exc_invalid_op+0x16/0x20
[ 682.146727] ? group_cpus_evenly+0x1aa/0x1c0
[ 682.146729] ? group_cpus_evenly+0x15c/0x1c0
[ 682.146731] create_affinity_masks+0xaf/0x1a0
[ 682.146735] virtio_vdpa_find_vqs+0x83/0x1d0
[ 682.146738] ? __pfx_default_calc_sets+0x10/0x10
[ 682.146742] virtnet_find_vqs+0x1f0/0x370
[ 682.146747] virtnet_probe+0x501/0xcd0
[ 682.146749] ? vp_modern_get_status+0x12/0x20
[ 682.146751] ? get_cap_addr.isra.0+0x10/0xc0
[ 682.146754] virtio_dev_probe+0x1af/0x260
[ 682.146759] really_probe+0x1a5/0x410
Fixes: 3dad56823b53 ("virtio-vdpa: Support interrupt affinity spreading mechanism")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230811091539.1359865-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently, the virtio core will perform a dma operation for each
buffer. Although, the same page may be operated multiple times.
This patch, the driver does the dma operation and manages the dma
address based the feature premapped of virtio core.
This way, we can perform only one dma operation for the pages of the
alloc frag. This is beneficial for the iommu device.
kernel command line: intel_iommu=on iommu.passthrough=0
| strict=0 | strict=1
Before | 775496pps | 428614pps
After | 1109316pps | 742853pps
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20230810123057.43407-13-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
These API has been introduced:
* virtqueue_dma_need_sync
* virtqueue_dma_sync_single_range_for_cpu
* virtqueue_dma_sync_single_range_for_device
These APIs can be used together with the premapped mechanism to sync the
DMA address.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20230810123057.43407-12-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Added virtqueue_dma_map_api* to map DMA addresses for virtual memory in
advance. The purpose is to keep memory mapped across multiple add/get
buf operations.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20230810123057.43407-11-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Introduce virtqueue_reset() to release all buffer inside vq.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230810123057.43407-10-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The subsequent reset function will reuse these logic.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230810123057.43407-9-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
