| Age | Commit message (Collapse) | Author |
|---|
|
Add clock driver for iPAQ audio sysclock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert the 3c589_cs driver to NAPI to ease the interrupt workload.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for a transceiver enable GPIO signal, which allows the
external RS232 transceiver on several platforms to be force-enabled
or force-disabled according to the system state and the hardware
capabilities.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The iPAQ H3xxx platforms used to wake up on DCD or DSR transitions.
However, at some point this got broken and fails to work today. Fix
this by using the newly added modem control gpio layer's wakeup
controls.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow serial control GPIOs to be used as a wakeup source for the system.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Switch the E740 machine to use the gpiod APIs rather than hard-coding
the GPIO numbers in the board specific PCMCIA driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Switch the Colibri family of devices to use the gpiod APIs rather than
listing the GPIOs and interrupts in the board specific PCMCIA driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some I2C driver bugfixes for 5.18. Nothing spectacular but worth
fixing"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
drivers: i2c: thunderx: Allow driver to work with ACPI defined TWSI controllers
i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging
i2c: mt7621: fix missing clk_disable_unprepare() on error in mtk_i2c_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A small fixup to ili210x touchscreen driver, and updated maintainer
entry for the device tree binding of Mediatek 6779 keypad:
- fix reset timing of Ilitek touchscreens
- update maintainer entry of DT binding of Mediatek 6779 keypad"
* tag 'input-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ili210x - use one common reset implementation
Input: ili210x - fix reset timing
dt-bindings: input: mediatek,mt6779-keypad: update maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches, both in drivers.
The iscsi one is fixing the cpumask issue you commented on and the ufs
one is a late arriving fix for conditions that can occur in Host
Performance Booster reads"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix referencing invalid rsp field
scsi: target: Fix incorrect use of cpumask_t
|
|
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fix the missing clk_disable_unprepare() before return
from mtk_i2c_probe() in the error handling case.
Fixes: d04913ec5f89 ("i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Three clk driver fixes to close out the release
- Fix a divider calculation breaking boot on Broadcom bcm2835
- Fix HDMI output on Tanix TX6 mini board by reverting a patch
- Fix clk_set_rate_range() calls on at91 by considering the range
while calculating the divisor"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: generated: consider range when calculating best rate
Revert "clk: sunxi-ng: sun6i-rtc: Add support for H6"
clk: bcm2835: fix bcm2835_clock_choose_div
|
|
Pull drm fixes from Dave Airlie:
"Few final fixes for 5.18, one amdgpu, core dp mst leak fix, dma-buf
two fixes, and i915 has a few fixes, one for a regression on older
GM45 chipsets,
dma-buf:
- ioctl userspace use fix
- fix dma-buf sysfs name generation
core:
- dp/mst leak fix
amdgpu:
- suspend/resume regression fix
i915:
- fix for #5806: GPU hangs and display artifacts on Intel GM45
- reject DMC with out-of-spec MMIO
- correctly mark guilty contexts on GuC reset"
* tag 'drm-fixes-2022-05-21' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Use i915_gem_object_ggtt_pin_ww for reloc_iomap
drm/amd: Don't reset dGPUs if the system is going to s2idle
drm/dp/mst: fix a possible memory leak in fetch_monitor_name()
dma-buf: fix use of DMA_BUF_SET_NAME_{A,B} in userspace
i915/guc/reset: Make __guc_reset_context aware of guilty engines
drm/i915/dmc: Add MMIO range restrictions
dma-buf: ensure unique directory name for dmabuf stats
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- fix for #5806: GPU hangs and display artifacts on 5.18-rc3 on Intel GM45
- reject DMC with out-of-spec MMIO (Cc: stable)
- correctly mark guilty contexts on GuC reset.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YocqqvG6PbYx3QgJ@jlahtine-mobl.ger.corp.intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fix for a memory leak in dp_mst, a (userspace) build fix for
DMA_BUF_SET_NAME defines and a directory name generation fix for dmabuf
stats
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520072408.cpjzy2taugagvrh7@houat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix bitops logic in gpio-vf610
- return an error if the user tries to use inverted polarity in
gpio-mvebu
* tag 'gpio-fixes-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: mvebu/pwm: Refuse requests with inverted polarity
gpio: gpio-vf610: do not touch other bits when set the target bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"MMC core:
- Fix busy polling for MMC_SEND_OP_COND again"
* tag 'mmc-v5.18-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Fix busy polling for MMC_SEND_OP_COND again
|
|
The driver doesn't take struct pwm_state::polarity into account when
configuring the hardware, so refuse requests for inverted polarity.
Fixes: 757642f9a584 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
Fixes: 659d8a62311f ("gpio: vf610: add imx7ulp support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression in a recent fix to qcom-rng"
* tag 'v5.18-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ
|
|
Fix referencing sense data when it is invalid. When the length of the data
segment is 0, there is no valid information in the rsp field, so
ufshpb_rsp_upiu() is returned without additional operation.
Link: https://lore.kernel.org/r/252651381.41652940482659.JavaMail.epsvc@epcpadp4
Fixes: 4b5f49079c52 ("scsi: ufs: ufshpb: L2P map management for HPB read")
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix an altmode in the Ocelot driver
- Fix the IES control pins in the Mediatek MT8365 driver
- Sunxi (AMLogic) driver:
- Fix the UART2 function pin assignments
- Fix the signal name of the PA2 SPI pin
* tag 'pinctrl-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: f1c100s: Fix signal name comment for PA2 SPI pin
pinctrl: sunxi: fix f1c100s uart2 function
pinctrl: mediatek: mt8365: fix IES control pins
pinctrl: ocelot: Fix for lan966x alt mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can, xfrm and netfilter subtrees.
Notably this reverts a recent TCP/DCCP netns-related change to address
a possible UaF.
Current release - regressions:
- tcp: revert "tcp/dccp: get rid of inet_twsk_purge()"
- xfrm: set dst dev to blackhole_netdev instead of loopback_dev in
ifdown
Previous releases - regressions:
- netfilter: flowtable: fix TCP flow teardown
- can: revert "can: m_can: pci: use custom bit timings for Elkhart
Lake"
- xfrm: check encryption module availability consistency
- eth: vmxnet3: fix possible use-after-free bugs in
vmxnet3_rq_alloc_rx_buf()
- eth: mlx5: initialize flow steering during driver probe
- eth: ice: fix crash when writing timestamp on RX rings
Previous releases - always broken:
- mptcp: fix checksum byte order
- eth: lan966x: fix assignment of the MAC address
- eth: mlx5: remove HW-GRO from reported features
- eth: ftgmac100: disable hardware checksum on AST2600"
* tag 'net-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
ptp: ocp: change sysfs attr group handling
selftests: forwarding: fix missing backslash
netfilter: nf_tables: disable expression reduction infra
netfilter: flowtable: move dst_check to packet path
netfilter: flowtable: fix TCP flow teardown
net: ftgmac100: Disable hardware checksum on AST2600
igb: skip phy status check where unavailable
nfc: pn533: Fix buggy cleanup order
mptcp: Do TCP fallback on early DSS checksum failure
mptcp: fix checksum byte order
net: af_key: check encryption module availability consistency
net: af_key: add check for pfkey_broadcast in function pfkey_process
net/mlx5: Drain fw_reset when removing device
net/mlx5e: CT: Fix setting flow_source for smfs ct tuples
net/mlx5e: CT: Fix support for GRE tuples
net/mlx5e: Remove HW-GRO from reported features
net/mlx5e: Properly block HW GRO when XDP is enabled
net/mlx5e: Properly block LRO when XDP is enabled
net/mlx5e: Block rx-gro-hw feature in switchdev mode
...
|
|
It turned out that polling period for MMC_SEND_OP_COND, that currently is
set to 1ms, still isn't sufficient. In particular a Micron eMMC on a
Beaglebone platform, is reported to sometimes fail to initialize.
Additional test, shows that extending the period to 4ms is working fine, so
let's make that change.
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Tested-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Fixes: 1760fdb6fe9f (mmc: core: Restore (almost) the busy polling for MMC_SEND_OP_COND")
Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220517101046.27512-1-ulf.hansson@linaro.org
|
|
When removing short term pins, I've changed the the batch buffer
pinning for relocation to use __i915_vma_pin, because
i915_gem_object_ggtt_pin_ww was destroying the old vma. This
caused regressions, because the functions are not identical.
Fix the regressions by calling i915_gem_object_ggtt_pin_ww() again
on ggtt-only platforms, but only if the batch can be pinned without
being moved.
Fixes: b5cfe6f7a6e1 ("drm/i915: Remove short-term pins from execbuf, v6.")
Cc: Matthew Auld <matthew.auld@intel.com>
Reported-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5806
Link: https://patchwork.freedesktop.org/patch/msgid/20220511115219.46507-1-maarten.lankhorst@linux.intel.com
(cherry picked from commit 451374eef622fca6f00eeeda89aaccb45a30a149)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
In the detach path, the driver calls sysfs_remove_group() for the
groups it believes has been registered. However, if the group was
never previously registered, then this causes a splat.
Instead, compute the groups that should be registered in advance,
and then call sysfs_create_groups(), which registers them all at once.
Update the error handling appropriately.
Fixes: c205d53c4923 ("ptp: ocp: Add firmware capability bits for feature gating")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220517214600.10606-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Reduce number of hardware offload retries from flowtable datapath
which might hog system with retries, from Felix Fietkau.
2) Skip neighbour lookup for PPPoE device, fill_forward_path() already
provides this and set on destination address from fill_forward_path for
PPPoE device, also from Felix.
4) When combining PPPoE on top of a VLAN device, set info->outdev to the
PPPoE device so software offload works, from Felix.
5) Fix TCP teardown flowtable state, races with conntrack gc might result
in resetting the state to ESTABLISHED and the time to one day. Joint
work with Oz Shlomo and Sven Auhagen.
6) Call dst_check() from flowtable datapath to check if dst is stale
instead of doing it from garbage collector path.
7) Disable register tracking infrastructure, either user-space or
kernel need to pre-fetch keys inconditionally, otherwise register
tracking assumes data is already available in register that might
not well be there, leading to incorrect reductions.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable expression reduction infra
netfilter: flowtable: move dst_check to packet path
netfilter: flowtable: fix TCP flow teardown
netfilter: nft_flow_offload: fix offload with pppoe + vlan
net: fix dev_fill_forward_path with pppoe + bridge
netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
netfilter: flowtable: fix excessive hw offload attempts after failure
====================
Link: https://lore.kernel.org/r/20220518213841.359653-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The SoC bug fixes have calmed down sufficiently, there is one minor
update for the MAINTAINERS file, and few bug fixes for dts
descriptions:
- Updates to the BananaPi R2-Pro (rk3568) dts to match production
hardware rather than the prototype version.
- Qualcomm sm8250 soundwire gets disabled on some machines to avoid
crashes
- A number of aspeed SoC specific fixes, addressing incorrect pin
cotrol settings, some values in the romed8hm board, and a revert
for an accidental removal of a DT node"
* 'arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: omap: remove me as a maintainer
ARM: dts: aspeed: Add video engine to g6
ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values
ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
ARM: dts: aspeed-g6: add FWQSPI group in pinctrl dtsi
dt-bindings: pinctrl: aspeed-g6: add FWQSPI function/group
pinctrl: pinctrl-aspeed-g6: add FWQSPI function-group
dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
arm64: dts: qcom: sm8250: don't enable rx/tx macro by default
arm64: dts: rockchip: Add gmac1 and change network settings of bpi-r2-pro
arm64: dts: rockchip: Change io-domains of bpi-r2-pro
|
|
Pull misc fixes from Al Viro:
"vhost race fix and a percpu_ref_init-caused cgroup double-free fix.
The latter had manifested as buggered struct mount refcounting - those
are also using percpu data structures, but anything that does percpu
allocations could be hit"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix double fget() in vhost_net_set_backend()
percpu_ref_init(): clean ->percpu_count_ref on failure
|
|
Pull mlx5 fix from Michael Tsirkin:
"One last minute fixup
The patch has been on list for a while but as it was posted as part of
a thread it was missed"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Use consistent RQT size
|
|
Rename ili251x_hardware_reset() to ili210x_hardware_reset(), change its
parameter from struct device * to struct gpio_desc *, and use it as one
single consistent reset implementation all over the driver. Also increase
the minimum reset duration to 12ms, to make sure the reset is really
within the spec.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518210423.106555-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c803544c ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
An A+A configuration on ASUS ROG Strix G513QY proves that the ASIC
reset for handling aborted suspend can't work with s2idle.
This functionality was introduced in commit daf8de0874ab5b ("drm/amdgpu:
always reset the asic in suspend (v2)"). A few other commits have
gone on top of the ASIC reset, but this still doesn't work on the A+A
configuration in s2idle.
Avoid doing the reset on dGPUs specifically when using s2idle.
Fixes: daf8de0874ab5b ("drm/amdgpu: always reset the asic in suspend (v2)")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2008
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Descriptor table is a shared resource; two fget() on the same descriptor
may return different struct file references. get_tap_ptr_ring() is
called after we'd found (and pinned) the socket we'll be using and it
tries to find the private tun/tap data structures associated with it.
Redoing the lookup by the same file descriptor we'd used to get the
socket is racy - we need to same struct file.
Thanks to Jason for spotting a braino in the original variant of patch -
I'd missed the use of fd == -1 for disabling backend, and in that case
we can end up with sock == NULL and sock != oldsock.
Cc: stable@kernel.org
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The current code evaluates RQT size based on the configured number of
virtqueues. This can raise an issue in the following scenario:
Assume MQ was negotiated.
1. mlx5_vdpa_set_map() gets called.
2. handle_ctrl_mq() is called setting cur_num_vqs to some value, lower
than the configured max VQs.
3. A second set_map gets called, but now a smaller number of VQs is used
to evaluate the size of the RQT.
4. handle_ctrl_mq() is called with a value larger than what the RQT can
hold. This will emit errors and the driver state is compromised.
To fix this, we use a new field in struct mlx5_vdpa_net to hold the
required number of entries in the RQT. This value is evaluated in
mlx5_vdpa_set_driver_features() where we have the negotiated features
all set up.
In addition to that, we take into consideration the max capability of RQT
entries early when the device is added so we don't need to take consider
it when creating the RQT.
Last, we remove the use of mlx5_vdpa_max_qps() which just returns the
max_vas / 2 and make the code clearer.
Fixes: 52893733f2c5 ("vdpa/mlx5: Add multiqueue support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The AST2600 when using the i210 NIC over NC-SI has been observed to
produce incorrect checksum results with specific MTU values. This was
first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of
random data.
On the receiver run this script:
#!/bin/bash
while [ 1 ]; do
# Zero the stats
nstat -r > /dev/null
nc -l 9899 > test-file
# Check for checksum errors
TcpInCsumErrors=$(nstat | grep TcpInCsumErrors)
if [ -z "$TcpInCsumErrors" ]; then
echo No TcpInCsumErrors
else
echo TcpInCsumErrors = $TcpInCsumErrors
fi
done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good
1434 - bad
1400 - good
1410 - bad
1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no
bug discovered so far.
David has done the work to take the original bug report of slow data
transfer between long distance connections and triaged it down to this
test case.
The vendor suspects this this is a hardware issue when using NC-SI. The
fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder <wilder@us.ibm.com>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f72005d ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing the pn533 device (i2c or USB), there is a logic error. The
original code first cancels the worker (flush_delayed_work) and then
destroys the workqueue (destroy_workqueue), leaving the timer the last
one to be deleted (del_timer). This result in a possible race condition
in a multi-core preempt-able kernel. That is, if the cleanup
(pn53x_common_clean) is concurrently run with the timer handler
(pn533_listen_mode_timer), the timer can queue the poll_work to the
already destroyed workqueue, causing use-after-free.
This patch reorder the cleanup: it uses the del_timer_sync to make sure
the handler is finished before the routine will destroy the workqueue.
Note that the timer cannot be activated by the worker again.
static void pn533_wq_poll(struct work_struct *work)
...
rc = pn533_send_poll_frame(dev);
if (rc)
return;
if (cur_mod->len == 0 && dev->poll_mod_count > 1)
mod_timer(&dev->listen_timer, ...);
That is, the mod_timer can be called only when pn533_send_poll_frame()
returns no error, which is impossible because the device is detaching
and the lower driver should return ENODEV code.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-05-17
This series contains updates to ice driver only.
Arkadiusz prevents writing of timestamps when rings are being
configured to resolve null pointer dereference.
Paul changes a delayed call to baseline statistics to occur immediately
which was causing misreporting of statistics due to the delay.
Michal fixes incorrect restoration of interrupt moderation settings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case fw sync reset is called in parallel to device removal, device
might stuck in the following deadlock:
CPU 0 CPU 1
----- -----
remove_one
uninit_one (locks intf_state_mutex)
mlx5_sync_reset_now_event()
work in fw_reset->wq.
mlx5_enter_error_state()
mutex_lock (intf_state_mutex)
cleanup_once
fw_reset_cleanup()
destroy_workqueue(fw_reset->wq)
Drain the fw_reset WQ, and make sure no new work is being queued, before
entering uninit_one().
The Drain is done before devlink_unregister() since fw_reset, in some
flows, is using devlink API devlink_remote_reload_actions_performed().
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
