| Age | Commit message (Collapse) | Author |
|---|
|
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1f9 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some boards with this chip version the BIOS is buggy and misses
to reset the PHY page selector. This results in the PHY ID read
accessing registers on a different page, returning a more or
less random value. Fix this by resetting the page selector first.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/64f2055e-98b8-45ec-8568-665e3d54d4e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove
administratively set MAC") fixed an issue where untrusted VF was
allowed to remove its own MAC address although this was assigned
administratively from PF. Unfortunately the introduced check
is wrong because it causes that MAC filters for other MAC addresses
including multi-cast ones are not removed.
<snip>
if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
i40e_can_vf_change_mac(vf))
was_unimac_deleted = true;
else
continue;
if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
...
</snip>
The else path with `continue` effectively skips any MAC filter
removal except one for primary MAC addr when VF is allowed to do so.
Fix the check condition so the `continue` is only done for primary
MAC address.
Fixes: 73d9629e1c8c ("i40e: Do not allow untrusted VF to remove administratively set MAC")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Bluetooth: Fix TOCTOU in HCI debugfs implementation
- Bluetooth: hci_event: set the conn encrypted before conn establishes
- Bluetooth: qca: fix device-address endianness
- Bluetooth: hci_sync: Fix not checking error on hci_cmd_sync_cancel_sync
* tag 'for-net-2024-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: Fix TOCTOU in HCI debugfs implementation
Bluetooth: hci_event: set the conn encrypted before conn establishes
Bluetooth: hci_sync: Fix not checking error on hci_cmd_sync_cancel_sync
Bluetooth: qca: fix device-address endianness
Bluetooth: add quirk for broken address properties
arm64: dts: qcom: sc7180-trogdor: mark bluetooth address as broken
dt-bindings: bluetooth: add 'qcom,local-bd-address-broken'
Revert "Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT"
====================
Link: https://lore.kernel.org/r/20240329140453.2016486-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On devices that support DASH, the current code in the "rtl_loop_wait" function
raises false alarms when DASH is disabled. This occurs because the function
attempts to wait for the DASH firmware to be ready, even though it's not
relevant in this case.
r8169 0000:0c:00.0 eth0: RTL8168ep/8111ep, 38:7c:76:49:08:d9, XID 502, IRQ 86
r8169 0000:0c:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
r8169 0000:0c:00.0 eth0: DASH disabled
...
r8169 0000:0c:00.0 eth0: rtl_ep_ocp_read_cond == 0 (loop: 30, delay: 10000).
This patch modifies the driver start/stop functions to skip checking the DASH
firmware status when DASH is explicitly disabled. This prevents unnecessary
delays and false alarms.
The patch has been tested on several ThinkStation P8/PX workstations.
Fixes: 0ab0c45d8aae ("r8169: add handling DASH when DASH is disabled")
Signed-off-by: Atlas Yu <atlas.yu@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20240328055152.18443-1-atlas.yu@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otx2_rxtx_enable() return negative error code such as -EIO,
check -EIO rather than EIO to fix this problem.
Fixes: c926252205c4 ("octeontx2-pf: Disable packet I/O for graceful exit")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20240328020620.4054692-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-26 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera resolves an issue where descriptors could be missed when
exiting busy poll.
Aleksandr corrects counting of MAC filters to only include new or active
filters and resolves possible use of incorrect/stale 'vf' variable.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix vf may be used uninitialized in this function warning
i40e: fix i40e_count_filters() to count only active/new filters
i40e: Enforce software interrupt during busy-poll exit
====================
Link: https://lore.kernel.org/r/20240326162358.1224145-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a15 ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mlxbf_gige driver intermittantly encounters a NULL pointer
exception while the system is shutting down via "reboot" command.
The mlxbf_driver will experience an exception right after executing
its shutdown() method. One example of this exception is:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000011d373000
[0000000000000070] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
CPU: 0 PID: 13 Comm: ksoftirqd/0 Tainted: G S OE 5.15.0-bf.6.gef6992a #1
Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS 4.0.2.12669 Apr 21 2023
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
lr : mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
sp : ffff8000080d3c10
x29: ffff8000080d3c10 x28: ffffcce72cbb7000 x27: ffff8000080d3d58
x26: ffff0000814e7340 x25: ffff331cd1a05000 x24: ffffcce72c4ea008
x23: ffff0000814e4b40 x22: ffff0000814e4d10 x21: ffff0000814e4128
x20: 0000000000000000 x19: ffff0000814e4a80 x18: ffffffffffffffff
x17: 000000000000001c x16: ffffcce72b4553f4 x15: ffff80008805b8a7
x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101
x11: 7f7f7f7f7f7f7f7f x10: c2ac898b17576267 x9 : ffffcce720fa5404
x8 : ffff000080812138 x7 : 0000000000002e9a x6 : 0000000000000080
x5 : ffff00008de3b000 x4 : 0000000000000000 x3 : 0000000000000001
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
__napi_poll+0x40/0x1c8
net_rx_action+0x314/0x3a0
__do_softirq+0x128/0x334
run_ksoftirqd+0x54/0x6c
smpboot_thread_fn+0x14c/0x190
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
Code: 8b070000 f9000ea0 f95056c0 f86178a1 (b9407002)
---[ end trace 7cc3941aa0d8e6a4 ]---
Kernel panic - not syncing: Oops: Fatal exception in interrupt
Kernel Offset: 0x4ce722520000 from 0xffff800008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x000005c1,a3330e5a
Memory Limit: none
---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
During system shutdown, the mlxbf_gige driver's shutdown() is always executed.
However, the driver's stop() method will only execute if networking interface
configuration logic within the Linux distribution has been setup to do so.
If shutdown() executes but stop() does not execute, NAPI remains enabled
and this can lead to an exception if NAPI is scheduled while the hardware
interface has only been partially deinitialized.
The networking interface managed by the mlxbf_gige driver must be properly
stopped during system shutdown so that IFF_UP is cleared, the hardware
interface is put into a clean state, and NAPI is fully deinitialized.
Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240325210929.25362-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts commit 7dcd3e014aa7faeeaf4047190b22d8a19a0db696.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc81a ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014aa7 ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf5b ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-27 (e1000e)
This series contains updates to e1000e driver only.
Vitaly adds retry mechanism for some PHY operations to workaround MDI
error and moves SMBus configuration to avoid possible PHY loss.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue
e1000e: Workaround for sporadic MDI error on Meteor Lake systems
====================
Link: https://lore.kernel.org/r/20240327185517.2587564-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Notice that skb_mark_for_recycle() is introduced later than fixes tag in
commit 6a5bcd84e886 ("page_pool: Allow drivers to hint on SKB recycling").
It is believed that fixes tag were missing a call to page_pool_release_page()
between v5.9 to v5.14, after which is should have used skb_mark_for_recycle().
Since v6.6 the call page_pool_release_page() were removed (in
commit 535b9c61bdef ("net: page_pool: hide page_pool_release_page()")
and remaining callers converted (in commit 6bfef2ec0172 ("Merge branch
'net-page_pool-remove-page_pool_release_page'")).
This leak became visible in v6.8 via commit dba1b8a7ab68 ("mm/page_pool: catch
page_pool memory leaks").
Cc: stable@vger.kernel.org
Fixes: 6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront")
Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf, WiFi and netfilter.
Current release - regressions:
- ipv6: fix address dump when IPv6 is disabled on an interface
Current release - new code bugs:
- bpf: temporarily disable atomic operations in BPF arena
- nexthop: fix uninitialized variable in nla_put_nh_group_stats()
Previous releases - regressions:
- bpf: protect against int overflow for stack access size
- hsr: fix the promiscuous mode in offload mode
- wifi: don't always use FW dump trig
- tls: adjust recv return with async crypto and failed copy to
userspace
- tcp: properly terminate timers for kernel sockets
- ice: fix memory corruption bug with suspend and rebuild
- at803x: fix kernel panic with at8031_probe
- qeth: handle deferred cc1
Previous releases - always broken:
- bpf: fix bug in BPF_LDX_MEMSX
- netfilter: reject table flag and netdev basechain updates
- inet_defrag: prevent sk release while still in use
- wifi: pick the version of SESSION_PROTECTION_NOTIF
- wwan: t7xx: split 64bit accesses to fix alignment issues
- mlxbf_gige: call request_irq() after NAPI initialized
- hns3: fix kernel crash when devlink reload during pf
initialization"
* tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
inet: inet_defrag: prevent sk release while still in use
Octeontx2-af: fix pause frame configuration in GMP mode
net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips
net: bcmasp: Remove phy_{suspend/resume}
net: bcmasp: Bring up unimac after PHY link up
net: phy: qcom: at803x: fix kernel panic with at8031_probe
netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c
netfilter: nf_tables: skip netdev hook unregistration if table is dormant
netfilter: nf_tables: reject table flag and netdev basechain updates
netfilter: nf_tables: reject destroy command to remove basechain hooks
bpf: update BPF LSM designated reviewer list
bpf: Protect against int overflow for stack access size
bpf: Check bloom filter map value size
bpf: fix warning for crash_kexec
selftests: netdevsim: set test timeout to 10 minutes
net: wan: framer: Add missing static inline qualifiers
mlxbf_gige: call request_irq() after NAPI initialized
tls: get psock ref after taking rxlock to avoid leak
selftests: tls: add test with a partially invalid iov
tls: adjust recv return with async crypto and failed copy to userspace
...
|
|
The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for
different speeds, allowing for efficient data transfer.
The previous patch which added pause frame configuration has a bug due
to which pause frame feature is not working in GMP mode.
This patch fixes the issue by configurating appropriate registers.
Fixes: f7e086e754fe ("octeontx2-af: Pause frame configuration at cgx")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PCI11x1x Rev B0 devices might drop packets when receiving back to back frames
at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO
threshold parameter from its hardware default of 4 to 3 dwords to prevent the
problem. Rev C0 and later hardware already defaults to 3 dwords.
Fixes: bb4f6bffe33c ("net: lan743x: Add PCI11010 / PCI11414 device IDs")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phy_{suspend/resume} is redundant. It gets called from phy_{stop/start}.
Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The unimac requires the PHY RX clk during reset or it may be put
into a bad state. Bring up the unimac after link up to ensure the
PHY RX clk exists.
Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.
Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct.
Reported-by: William Wortel <wwortel@dorpstraat.com>
Cc: <stable@vger.kernel.org>
Fixes: 25d2ba94005f ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.9-rc2
The first fixes for v6.9. Ping-Ke Shih now maintains a separate tree
for Realtek drivers, document that in the MAINTAINERS. Plenty of fixes
for both to stack and iwlwifi. Our kunit tests were working only on um
architecture but that's fixed now.
* tag 'wireless-2024-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (21 commits)
MAINTAINERS: wifi: mwifiex: add Francesco as reviewer
kunit: fix wireless test dependencies
wifi: iwlwifi: mvm: include link ID when releasing frames
wifi: iwlwifi: mvm: handle debugfs names more carefully
wifi: iwlwifi: mvm: guard against invalid STA ID on removal
wifi: iwlwifi: read txq->read_ptr under lock
wifi: iwlwifi: fw: don't always use FW dump trig
wifi: iwlwifi: mvm: rfi: fix potential response leaks
wifi: mac80211: correctly set active links upon TTLM
wifi: iwlwifi: mvm: Configure the link mapping for non-MLD FW
wifi: iwlwifi: mvm: consider having one active link
wifi: iwlwifi: mvm: pick the version of SESSION_PROTECTION_NOTIF
wifi: mac80211: fix prep_connection error path
wifi: cfg80211: fix rdev_dump_mpp() arguments order
wifi: iwlwifi: mvm: disable MLO for the time being
wifi: cfg80211: add a flag to disable wireless extensions
wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc
wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes
wifi: mac80211: fix mlme_link_id_dbg()
MAINTAINERS: wifi: add git tree for Realtek WiFi drivers
...
====================
Link: https://lore.kernel.org/r/20240327191346.1A1EAC433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.
Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.
Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state")
Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
On some Meteor Lake systems accessing the PHY via the MDIO interface may
result in an MDI error. This issue happens sporadically and in most cases
a second access to the PHY via the MDIO interface results in success.
As a workaround, introduce a retry counter which is set to 3 on Meteor
Lake systems. The driver will only return an error if 3 consecutive PHY
access attempts fail. The retry mechanism is disabled in specific flows,
where MDI errors are expected.
Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake")
Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com>
Co-developed-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Nir Efrati <nir.efrati@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 576882ef5e7f ("uio: introduce UIO_MEM_DMA_COHERENT type")
introduced a new use-case for 'struct uio_mem' where the 'mem' field now
contains a kernel virtual address when 'memtype' is set to
UIO_MEM_DMA_COHERENT.
That in turn causes build errors, because 'mem' is of type
'phys_addr_t', and a virtual address is a pointer type. When the code
just blindly uses cast to mix the two, it caused problems when
phys_addr_t isn't the same size as a pointer - notably on 32-bit
architectures with PHYS_ADDR_T_64BIT.
The proper thing to do would probably be to use a union member, and not
have any casts, and make the 'mem' member be a union of 'mem.physaddr'
and 'mem.vaddr', based on 'memtype'.
This is not that proper thing. This is just fixing the ugly casts to be
even uglier, but at least not cause build errors on 32-bit platforms
with 64-bit physical addresses.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 576882ef5e7f ("uio: introduce UIO_MEM_DMA_COHERENT type")
Fixes: 7722151e4651 ("uio_pruss: UIO_MEM_DMA_COHERENT conversion")
Fixes: 019947805a8d ("uio_dmem_genirq: UIO_MEM_DMA_COHERENT conversion")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Chris Leech <cleech@redhat.com>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-25 (ice, ixgbe, igc)
This series contains updates to ice, ixgbe, and igc drivers.
Steven fixes incorrect casting of bitmap type for ice driver.
Jesse fixes memory corruption issue with suspend flow on ice.
Przemek adds GFP_ATOMIC flag to avoid sleeping in IRQ context for ixgbe.
Kurt Kanzenbach removes no longer valid comment on igc.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Remove stale comment about Tx timestamping
ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa()
ice: fix memory corruption bug with suspend and rebuild
ice: Refactor FW data type and fix bitmap casting issue
====================
Link: https://lore.kernel.org/r/20240325200659.993749-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mlxbf_gige driver encounters a NULL pointer exception in
mlxbf_gige_open() when kdump is enabled. The sequence to reproduce
the exception is as follows:
a) enable kdump
b) trigger kdump via "echo c > /proc/sysrq-trigger"
c) kdump kernel executes
d) kdump kernel loads mlxbf_gige module
e) the mlxbf_gige module runs its open() as the
the "oob_net0" interface is brought up
f) mlxbf_gige module will experience an exception
during its open(), something like:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x0000000086000004
EC = 0x21: IABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e29a4000
[0000000000000000] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000086000004 [#1] SMP
CPU: 0 PID: 812 Comm: NetworkManager Tainted: G OE 5.15.0-1035-bluefield #37-Ubuntu
Hardware name: https://www.mellanox.com BlueField-3 SmartNIC Main Card/BlueField-3 SmartNIC Main Card, BIOS 4.6.0.13024 Jan 19 2024
pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : 0x0
lr : __napi_poll+0x40/0x230
sp : ffff800008003e00
x29: ffff800008003e00 x28: 0000000000000000 x27: 00000000ffffffff
x26: ffff000066027238 x25: ffff00007cedec00 x24: ffff800008003ec8
x23: 000000000000012c x22: ffff800008003eb7 x21: 0000000000000000
x20: 0000000000000001 x19: ffff000066027238 x18: 0000000000000000
x17: ffff578fcb450000 x16: ffffa870b083c7c0 x15: 0000aaab010441d0
x14: 0000000000000001 x13: 00726f7272655f65 x12: 6769675f6662786c
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa870b0842398
x8 : 0000000000000004 x7 : fe5a48b9069706ea x6 : 17fdb11fc84ae0d2
x5 : d94a82549d594f35 x4 : 0000000000000000 x3 : 0000000000400100
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000066027238
Call trace:
0x0
net_rx_action+0x178/0x360
__do_softirq+0x15c/0x428
__irq_exit_rcu+0xac/0xec
irq_exit+0x18/0x2c
handle_domain_irq+0x6c/0xa0
gic_handle_irq+0xec/0x1b0
call_on_irq_stack+0x20/0x2c
do_interrupt_handler+0x5c/0x70
el1_interrupt+0x30/0x50
el1h_64_irq_handler+0x18/0x2c
el1h_64_irq+0x7c/0x80
__setup_irq+0x4c0/0x950
request_threaded_irq+0xf4/0x1bc
mlxbf_gige_request_irqs+0x68/0x110 [mlxbf_gige]
mlxbf_gige_open+0x5c/0x170 [mlxbf_gige]
__dev_open+0x100/0x220
__dev_change_flags+0x16c/0x1f0
dev_change_flags+0x2c/0x70
do_setlink+0x220/0xa40
__rtnl_newlink+0x56c/0x8a0
rtnl_newlink+0x58/0x84
rtnetlink_rcv_msg+0x138/0x3c4
netlink_rcv_skb+0x64/0x130
rtnetlink_rcv+0x20/0x30
netlink_unicast+0x2ec/0x360
netlink_sendmsg+0x278/0x490
__sock_sendmsg+0x5c/0x6c
____sys_sendmsg+0x290/0x2d4
___sys_sendmsg+0x84/0xd0
__sys_sendmsg+0x70/0xd0
__arm64_sys_sendmsg+0x2c/0x40
invoke_syscall+0x78/0x100
el0_svc_common.constprop.0+0x54/0x184
do_el0_svc+0x30/0xac
el0_svc+0x48/0x160
el0t_64_sync_handler+0xa4/0x12c
el0t_64_sync+0x1a4/0x1a8
Code: bad PC value
---[ end trace 7d1c3f3bf9d81885 ]---
Kernel panic - not syncing: Oops: Fatal exception in interrupt
Kernel Offset: 0x2870a7a00000 from 0xffff800008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x0,000005c1,a3332a5a
Memory Limit: none
---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
The exception happens because there is a pending RX interrupt before the
call to request_irq(RX IRQ) executes. Then, the RX IRQ handler fires
immediately after this request_irq() completes. The RX IRQ handler runs
"napi_schedule()" before NAPI is fully initialized via "netif_napi_add()"
and "napi_enable()", both which happen later in the open() logic.
The logic in mlxbf_gige_open() must fully initialize NAPI before any calls
to request_irq() execute.
Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Link: https://lore.kernel.org/r/20240325183627.7641-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fix from Uwe Kleine-König:
"This contains a single fix for a regression introduced in v5.18-rc1
which made the img pwm driver fail to bind"
* tag 'pwm/for-6.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: img: fix pwm clock lookup
|
|
To fix the regression introduced by commit 52424f974bc5, which causes
servers hang in very hard to reproduce conditions with resets races.
Using two sources for the information is the root cause.
In this function before the fix bumping v didn't mean bumping vf
pointer. But the code used this variables interchangeably, so stale vf
could point to different/not intended vf.
Remove redundant "v" variable and iterate via single VF pointer across
whole function instead to guarantee VF pointer validity.
Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The bug usually affects untrusted VFs, because they are limited to 18 MACs,
it affects them badly, not letting to create MAC all filters.
Not stable to reproduce, it happens when VF user creates MAC filters
when other MACVLAN operations are happened in parallel.
But consequence is that VF can't receive desired traffic.
Fix counter to be bumped only for new or active filters.
Fixes: 621650cabee5 ("i40e: Refactoring VF MAC filters counting to make more reliable")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As for ice bug fixed by commit b7306b42beaf ("ice: manage interrupts
during poll exit") followed by commit 23be7075b318 ("ice: fix software
generating extra interrupts") I'm seeing the similar issue also with
i40e driver.
In certain situation when busy-loop is enabled together with adaptive
coalescing, the driver occasionally misses that there are outstanding
descriptors to clean when exiting busy poll.
Try to catch the remaining work by triggering a software interrupt
when exiting busy poll. No extra interrupts will be generated when
busy polling is not used.
The issue was found when running sockperf ping-pong tcp test with
adaptive coalescing and busy poll enabled (50 as value busy_pool
and busy_read sysctl knobs) and results in huge latency spikes
with more than 100000us.
The fix is inspired from the ice driver and do the following:
1) During napi poll exit in case of busy-poll (napo_complete_done()
returns false) this is recorded to q_vector that we were in busy
loop.
2) Extends i40e_buildreg_itr() to be able to add an enforced software
interrupt into built value
2) In i40e_update_enable_itr() enforces a software interrupt trigger
if we are exiting busy poll to catch any pending clean-ups
3) Reuses unused 3rd ITR (interrupt throttle) index and set it to
20K interrupts per second to limit the number of these sw interrupts.
Test results
============
Prior:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2438563; ReceivedMessages=2438562
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2429473; ReceivedMessages=2429473
sockperf: ====> avg-latency=24.571 (std-dev=93.297, mean-ad=4.904, median-ad=1.510, siqr=1.063, cv=3.797, std-error=0.060, 99.0% ci=[24.417, 24.725])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.571 usec
sockperf: Total 2429473 observations; each percentile contains 24294.73 observations
sockperf: ---> <MAX> observation = 103294.331
sockperf: ---> percentile 99.999 = 45.633
sockperf: ---> percentile 99.990 = 37.013
sockperf: ---> percentile 99.900 = 35.910
sockperf: ---> percentile 99.000 = 33.390
sockperf: ---> percentile 90.000 = 28.626
sockperf: ---> percentile 75.000 = 27.741
sockperf: ---> percentile 50.000 = 26.743
sockperf: ---> percentile 25.000 = 25.614
sockperf: ---> <MIN> observation = 12.220
After:
[root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120
sockperf: == version #3.10-no.git ==
sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s)
[ 0] IP = 10.9.9.1 PORT = 11111 # TCP
sockperf: Warmup stage (sending a few dummy messages)...
sockperf: Starting test...
sockperf: Test end (interrupted by timer)
sockperf: Test ended
sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2400055; ReceivedMessages=2400054
sockperf: ========= Printing statistics for Server No: 0
sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2391186; ReceivedMessages=2391186
sockperf: ====> avg-latency=24.965 (std-dev=5.934, mean-ad=4.642, median-ad=1.485, siqr=1.067, cv=0.238, std-error=0.004, 99.0% ci=[24.955, 24.975])
sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0
sockperf: Summary: Latency is 24.965 usec
sockperf: Total 2391186 observations; each percentile contains 23911.86 observations
sockperf: ---> <MAX> observation = 195.841
sockperf: ---> percentile 99.999 = 45.026
sockperf: ---> percentile 99.990 = 39.009
sockperf: ---> percentile 99.900 = 35.922
sockperf: ---> percentile 99.000 = 33.482
sockperf: ---> percentile 90.000 = 28.902
sockperf: ---> percentile 75.000 = 27.821
sockperf: ---> percentile 50.000 = 26.860
sockperf: ---> percentile 25.000 = 25.685
sockperf: ---> <MIN> observation = 12.277
Fixes: 0bcd952feec7 ("ethernet/intel: consolidate NAPI and NAPI exit")
Reported-by: Hugo Ferreira <hferreir@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, loopback test may be skipped when resetting, but the test
result will still show as 'PASS', because the driver doesn't set
ETH_TEST_FL_FAILED flag. Fix it by setting the flag and
initializating the value to UNEXECUTED.
Fixes: 4c8dab1c709c ("net: hns3: reconstruct function hns3_self_test")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The devlink reload process will access the hardware resources,
but the register operation is done before the hardware is initialized.
So, processing the devlink reload during initialization may lead to kernel
crash. This patch fixes this by taking devl_lock during initialization.
Fixes: b741269b2759 ("net: hns3: add support for registering devlink for PF")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, hns hardware supports more than 512 queues and the index limit
in hclge_comm_tqps_update_stats is wrong. So this patch removes it.
Fixes: 287db5c40d15 ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/4a5dd143f2172ec97a2872fa29c7c4cd520f45b5/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c#L1039
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some of the registers are aligned on a 32bit boundary, causing
alignment faults on 64bit platforms.
Unable to handle kernel paging request at virtual address ffffffc084a1d004
Mem abort info:
ESR = 0x0000000096000061
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000061, ISS2 = 0x00000000
CM = 0, WnR = 1, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000046ad6000
[ffffffc084a1d004] pgd=100000013ffff003, p4d=100000013ffff003, pud=100000013ffff003, pmd=0068000020a00711
Internal error: Oops: 0000000096000061 [#1] SMP
Modules linked in: mtk_t7xx(+) qcserial pppoe ppp_async option nft_fib_inet nf_flow_table_inet mt7921u(O) mt7921s(O) mt7921e(O) mt7921_common(O) iwlmvm(O) iwldvm(O) usb_wwan rndis_host qmi_wwan pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mt7996e(O) mt792x_usb(O) mt792x_lib(O) mt7915e(O) mt76_usb(O) mt76_sdio(O) mt76_connac_lib(O) mt76(O) mac80211(O) iwlwifi(O) huawei_cdc_ncm cfg80211(O) cdc_ncm cdc_ether wwan usbserial usbnet slhc sfp rtc_pcf8563 nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 mt6577_auxadc mdio_i2c libcrc32c compat(O) cdc_wdm cdc_acm at24 crypto_safexcel pwm_fan i2c_gpio i2c_smbus industrialio i2c_algo_bit i2c_mux_reg i2c_mux_pca954x i2c_mux_pca9541 i2c_mux_gpio i2c_mux dummy oid_registry tun sha512_arm64 sha1_ce sha1_generic seqiv
md5 geniv des_generic libdes cbc authencesn authenc leds_gpio xhci_plat_hcd xhci_pci xhci_mtk_hcd xhci_hcd nvme nvme_core gpio_button_hotplug(O) dm_mirror dm_region_hash dm_log dm_crypt dm_mod dax usbcore usb_common ptp aquantia pps_core mii tpm encrypted_keys trusted
CPU: 3 PID: 5266 Comm: kworker/u9:1 Tainted: G O 6.6.22 #0
Hardware name: Bananapi BPI-R4 (DT)
Workqueue: md_hk_wq t7xx_fsm_uninit [mtk_t7xx]
pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx]
lr : t7xx_cldma_start+0xac/0x13c [mtk_t7xx]
sp : ffffffc085d63d30
x29: ffffffc085d63d30 x28: 0000000000000000 x27: 0000000000000000
x26: 0000000000000000 x25: ffffff80c804f2c0 x24: ffffff80ca196c05
x23: 0000000000000000 x22: ffffff80c814b9b8 x21: ffffff80c814b128
x20: 0000000000000001 x19: ffffff80c814b080 x18: 0000000000000014
x17: 0000000055c9806b x16: 000000007c5296d0 x15: 000000000f6bca68
x14: 00000000dbdbdce4 x13: 000000001aeaf72a x12: 0000000000000001
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffffff80ca1ef6b4 x7 : ffffff80c814b818 x6 : 0000000000000018
x5 : 0000000000000870 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 000000010a947000 x1 : ffffffc084a1d004 x0 : ffffffc084a1d004
Call trace:
t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx]
t7xx_fsm_uninit+0x578/0x5ec [mtk_t7xx]
process_one_work+0x154/0x2a0
worker_thread+0x2ac/0x488
kthread+0xe0/0xec
ret_from_fork+0x10/0x20
Code: f9400800 91001000 8b214001 d50332bf (f9000022)
---[ end trace 0000000000000000 ]---
The inclusion of io-64-nonatomic-lo-hi.h indicates that all 64bit
accesses can be replaced by pairs of nonatomic 32bit access. Fix
alignment by forcing all accesses to be 32bit on 64bit platforms.
Link: https://forum.openwrt.org/t/fibocom-fm350-gl-support/142682/72
Fixes: 39d439047f1d ("net: wwan: t7xx: Add control DMA interface")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Tested-by: Liviu Dudau <liviu@dudau.co.uk>
Link: https://lore.kernel.org/r/20240322144000.1683822-1-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function platform_get_resource was replaced with
devm_platform_ioremap_resource_byname and is called using 0 as name.
This eventually ends up in platform_get_resource_byname in the call
stack, where it causes a null pointer in strcmp.
if (type == resource_type(r) && !strcmp(r->name, name))
It should have been replaced with devm_platform_ioremap_resource.
Fixes: bd69058f50d5 ("net: ll_temac: Use devm_platform_ioremap_resource_byname()")
Signed-off-by: Claus Hansen Ries <chr@terma.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cca18f9c630a41c18487729770b492bb@terma.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IO subsystem expects a driver to retry a ccw_device_start, when the
subsequent interrupt response block (irb) contains a deferred
condition code 1.
Symptoms before this commit:
On the read channel we always trigger the next read anyhow, so no
different behaviour here.
On the write channel we may experience timeout errors, because the
expected reply will never be received without the retry.
Other callers of qeth_send_control_data() may wrongly assume that the ccw
was successful, which may cause problems later.
Note that since
commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
and
commit 5ef1dc40ffa6 ("s390/cio: fix invalid -EBUSY on ccw_device_start")
deferred CC1s are much more likely to occur. See the commit message of the
latter for more background information.
Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Co-developed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Link: https://lore.kernel.org/r/20240321115337.3564694-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Indent config option type by a tab. It helps Kconfig parsers
to read file without error.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240322114819.1801795-1-ppandit@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a regression that broke iwd as well as a divide by zero in
iaa"
* tag 'v6.9-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: iaa - Fix nr_cpus < nr_iaa case
Revert "crypto: pkcs7 - remove sha1 support"
|
|
The initial igc Tx timestamping implementation used only one register for
retrieving Tx timestamps. Commit 3ed247e78911 ("igc: Add support for
multiple in-flight TX timestamps") added support for utilizing all four of
them e.g., for multiple domain support. Remove the stale comment/FIXME.
Fixes: 3ed247e78911 ("igc: Add support for multiple in-flight TX timestamps")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change kzalloc() flags used in ixgbe_ipsec_vf_add_sa() to GFP_ATOMIC, to
avoid sleeping in IRQ context.
Dan Carpenter, with the help of Smatch, has found following issue:
The patch eda0333ac293: "ixgbe: add VF IPsec management" from Aug 13,
2018 (linux-next), leads to the following Smatch static checker
warning: drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c:917 ixgbe_ipsec_vf_add_sa()
warn: sleeping in IRQ context
The call tree that Smatch is worried about is:
ixgbe_msix_other() <- IRQ handler
-> ixgbe_msg_task()
-> ixgbe_rcv_msg_from_vf()
-> ixgbe_ipsec_vf_add_sa()
Fixes: eda0333ac293 ("ixgbe: add VF IPsec management")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/intel-wired-lan/db31a0b0-4d9f-4e6b-aed8-88266eb5665c@moroto.mountain
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver would previously panic after suspend. This is caused
from the driver *only* calling the ice_vsi_free_q_vectors() function by
itself, when it is suspending. Since commit b3e7b3a6ee92 ("ice: prevent
NULL pointer deref during reload") the driver has zeroed out
num_q_vectors, and only restored it in ice_vsi_cfg_def().
This further causes the ice_rebuild() function to allocate a zero length
buffer, after which num_q_vectors is updated, and then the new value of
num_q_vectors is used to index into the zero length buffer, which
corrupts memory.
The fix entails making sure all the code referencing num_q_vectors only
does so after it has been reset via ice_vsi_cfg_def().
I didn't perform a full bisect, but I was able to test against 6.1.77
kernel and that ice driver works fine for suspend/resume with no panic,
so sometime since then, this problem was introduced.
Also clean up an un-needed init of a local variable in the function
being modified.
PANIC from 6.8.0-rc1:
[1026674.915596] PM: suspend exit
[1026675.664697] ice 0000:17:00.1: PTP reset successful
[1026675.664707] ice 0000:17:00.1: 2755 msecs passed between update to cached PHC time
[1026675.667660] ice 0000:b1:00.0: PTP reset successful
[1026675.675944] ice 0000:b1:00.0: 2832 msecs passed between update to cached PHC time
[1026677.137733] ixgbe 0000:31:00.0 ens787: NIC Link is Up 1 Gbps, Flow Control: None
[1026677.190201] BUG: kernel NULL pointer dereference, address: 0000000000000010
[1026677.192753] ice 0000:17:00.0: PTP reset successful
[1026677.192764] ice 0000:17:00.0: 4548 msecs passed between update to cached PHC time
[1026677.197928] #PF: supervisor read access in kernel mode
[1026677.197933] #PF: error_code(0x0000) - not-present page
[1026677.197937] PGD 1557a7067 P4D 0
[1026677.212133] ice 0000:b1:00.1: PTP reset successful
[1026677.212143] ice 0000:b1:00.1: 4344 msecs passed between update to cached PHC time
[1026677.212575]
[1026677.243142] Oops: 0000 [#1] PREEMPT SMP NOPTI
[1026677.247918] CPU: 23 PID: 42790 Comm: kworker/23:0 Kdump: loaded Tainted: G W 6.8.0-rc1+ #1
[1026677.257989] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[1026677.269367] Workqueue: ice ice_service_task [ice]
[1026677.274592] RIP: 0010:ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice]
[1026677.281421] Code: 0f 84 3a ff ff ff 41 0f b7 74 ec 02 66 89 b0 22 02 00 00 81 e6 ff 1f 00 00 e8 ec fd ff ff e9 35 ff ff ff 48 8b 43 30 49 63 ed <41> 0f b7 34 24 41 83 c5 01 48 8b 3c e8 66 89 b7 aa 02 00 00 81 e6
[1026677.300877] RSP: 0018:ff3be62a6399bcc0 EFLAGS: 00010202
[1026677.306556] RAX: ff28691e28980828 RBX: ff28691e41099828 RCX: 0000000000188000
[1026677.314148] RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff28691e41099828
[1026677.321730] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[1026677.329311] R10: 0000000000000007 R11: ffffffffffffffc0 R12: 0000000000000010
[1026677.336896] R13: 0000000000000000 R14: 0000000000000000 R15: ff28691e0eaa81a0
[1026677.344472] FS: 0000000000000000(0000) GS:ff28693cbffc0000(0000) knlGS:0000000000000000
[1026677.353000] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1026677.359195] CR2: 0000000000000010 CR3: 0000000128df4001 CR4: 0000000000771ef0
[1026677.366779] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1026677.374369] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1026677.381952] PKRU: 55555554
[1026677.385116] Call Trace:
[1026677.388023] <TASK>
[1026677.390589] ? __die+0x20/0x70
[1026677.394105] ? page_fault_oops+0x82/0x160
[1026677.398576] ? do_user_addr_fault+0x65/0x6a0
[1026677.403307] ? exc_page_fault+0x6a/0x150
[1026677.407694] ? asm_exc_page_fault+0x22/0x30
[1026677.412349] ? ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice]
[1026677.418614] ice_vsi_rebuild+0x34b/0x3c0 [ice]
[1026677.423583] ice_vsi_rebuild_by_type+0x76/0x180 [ice]
[1026677.429147] ice_rebuild+0x18b/0x520 [ice]
[1026677.433746] ? delay_tsc+0x8f/0xc0
[1026677.437630] ice_do_reset+0xa3/0x190 [ice]
[1026677.442231] ice_service_task+0x26/0x440 [ice]
[1026677.447180] process_one_work+0x174/0x340
[1026677.451669] worker_thread+0x27e/0x390
[1026677.455890] ? __pfx_worker_thread+0x10/0x10
[1026677.460627] kthread+0xee/0x120
[1026677.464235] ? __pfx_kthread+0x10/0x10
[1026677.468445] ret_from_fork+0x2d/0x50
[1026677.472476] ? __pfx_kthread+0x10/0x10
[1026677.476671] ret_from_fork_asm+0x1b/0x30
[1026677.481050] </TASK>
Fixes: b3e7b3a6ee92 ("ice: prevent NULL pointer deref during reload")
Reported-by: Robert Elliott <elliott@hpe.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
According to the datasheet, the recipe association data is an 8-byte
little-endian value. It is described as 'Bitmap of the recipe indexes
associated with this profile', it is from 24 to 31 byte area in FW.
Therefore, it is defined to '__le64 recipe_assoc' in struct
ice_aqc_recipe_to_profile. And then fix the bitmap casting issue, as we
must never ever use castings for bitmap type.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Steven Zou <steven.zou@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When releasing frames from the reorder buffer, the link ID was not
included in the RX status information. This subsequently led mac80211 to
drop the frame. Change it so that the link information is set
immediately when possible so that it doesn't not need to be filled in
anymore when submitting the frame to mac80211.
Fixes: b8a85a1d42d7 ("wifi: iwlwifi: mvm: rxmq: report link ID to mac80211")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.bbbd5e9bfe80.Iec1bf5c884e371f7bc5ea2534ed9ea8d3f2c0bf6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With debugfs=off, we can get here with the dbgfs_dir being
an ERR_PTR(). Instead of checking for all this, which is
often flagged as a mistake, simply handle the names here
more carefully by printing them, then we don't need extra
checks.
Also, while checking, I noticed theoretically 'buf' is too
small, so fix that size as well.
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218422
Fixes: c36235acb34f ("wifi: iwlwifi: mvm: rework debugfs handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.4dc1eb3dd015.I32f308b0356ef5bcf8d188dd98ce9b210e3ab9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Guard against invalid station IDs in iwl_mvm_mld_rm_sta_id as that would
result in out-of-bounds array accesses. This prevents issues should the
driver get into a bad state during error handling.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.d523167bda9c.I1cffd86363805bf86a95d8bdfd4b438bb54baddc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we read txq->read_ptr without lock, we can read the same
value twice, then obtain the lock, and reclaim from there
to two different places, but crucially reclaim the same
entry twice, resulting in the WARN_ONCE() a little later.
Fix that by reading txq->read_ptr under lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.bf4c62196504.I978a7ca56c6bd6f1bf42c15aa923ba03366a840b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the dump_data (struct iwl_fwrt_dump_data) is a union,
it's not safe to unconditionally access and use the 'trig'
member, it might be 'desc' instead. Access it only if it's
known to be 'trig' rather than 'desc', i.e. if ini-debug
is present.
Cc: stable@vger.kernel.org
Fixes: 0eb50c674a1e ("iwlwifi: yoyo: send hcmd to fw after dump collection completes.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.e2976bc58b29.I72fbd6135b3623227de53d8a2bb82776066cb72b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
