| Age | Commit message (Collapse) | Author |
|---|
|
The driver stores the result of irq_set_type() in the internal variables
irq_trig_raise and irq_trig_fall, which later are used to determine
the GPIOs that must be re-configured as input. These variables retain their
value between gpiolib's export / unexport, resulting in an incorrect
state in some cases. The corresponding bits in the variables
irq_trig_raise and irq_trig_fall should be cleared in irq_shutdown().
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In past Xilinx gpio-zynq driver was setting up gpio chip->base as 0
which was chagned to autodetection when driver was upstreamed. Older
systems, which were using this old version, setup SW stack which expects
zynq gpio base as 0 and right now there is no way how to set this up.
The patch is adding an option to setup chip->base based on aliases which
is something what some other drivers are doing too.
It means when gpio0 alias is setup then chip->base is 0. When gpio alias
is not setup gpiochip_find_base() set it up properly which is current
behavior.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Treat DT and ACPI the same as much as possible. Note that we can't use
platform_get_irq() to get the DT interrupts as they are in the port
sub-node and hence do not have an associated platform device.
This also fixes a problem introduced with error checking when calling
platform_get_irq().
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Syscon nodes can be a simple-mfd and the syscon-users then be declared
as children of this node. That way the parent-child structure can be
better represented for devices that are fully embedded in the syscon.
Therefore allow getting the syscon from the parent if neither
a special compatible nor a gpio,syscon-dev property is defined.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Get the driver data directly by dev_get_drvdata.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove the call to platform_get_irq use the cached
one instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new helper returns index of the matching string in an array.
We are going to use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pcal6524 has another set of registers to fine control
the interrupt handling.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PCAL chips ("L" seems to stand for "latched") have additional
registers starting at address 0x40 to control the latches,
interrupt mask, pull-up and pull down etc.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
which makes it easier to match them with the data sheets.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Casting a pointer to u16 can produce a compiler warning such as this:
drivers/gpio/gpio-ge.c: In function 'gef_gpio_probe':
drivers/gpio/gpio-ge.c:83:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
gc->ngpio = (u16)of_device_get_match_data(&pdev->dev);
^
Cast the pointer through a uintptr_t to avoid the warning.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a shifter vs vanilla mask bug here. We want to test if 1 << 11
is set but we're testing if 0xb is set.
Fixes: 9a6c505f7df1 ("gpiolib: add hogs support for machine code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_device_get_match_data() instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the SPDX license identifier for GPLv2.0 or later and remove the
license boilerplate.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DesignWare GPIO IP can be configured for either 1 interrupt or 1
per GPIO in port A, but the driver currently only supports 1 interrupt.
See the DesignWare DW_apb_gpio Databook description of the
'GPIO_INTR_IO' parameter.
This change allows the driver to work with up to 32 interrupts, it will
get as many interrupts as specified in the DT 'interrupts' property.
It doesn't do anything clever with the different interrupts, it just calls
the same handler used for single interrupt hardware.
ACPI companion code provided by Hoan Tran <hotran@apm.com>. This was tested
on X-Gene by Hoan.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Don't populate the const read-only arrays 'port' on the stack but
instead make them static. Makes the object code smaller:
Before:
text data bss dec hex filename
8542 4088 672 13302 33f6 drivers/gpio/gpio-gpio-mm.o
10959 4952 832 16743 4167 drivers/gpio/gpio-104-dio-48e.o
9022 5064 1408 15494 3c86 drivers/gpio/gpio-104-idi-48.o
After:
text data bss dec hex filename
8372 4144 672 13188 3384 drivers/gpio/gpio-gpio-mm.o
10790 5008 832 16630 40f6 drivers/gpio/gpio-104-dio-48e.o
8853 5152 1408 15413 3c35 linux/drivers/gpio/gpio-104-idi-48.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so we should only include <linux/gpio/driver.h>.
However this driver was using gpio_get_value() to fetch the
current value of a GPIO used as IRQ line to determine trigger
direction, so we need a better way than looping over the
global GPIO numberspace.
Fix this by just calling the .get() function in the GPIO chip,
as we don't want to end up creating a consumer dependency
on ourselves.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MVEBU driver is requesting GPIO descriptors from itself, which
is fine, but we have proper APIs to do this in a controlled way, so
stop calling into the private functions of the GPIO library and use
the gpiochip_* functions instead. Only include <linux/gpio/driver.h>
and <linux/gpio/consumer.h> since we are both producers and consumers
in this case.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver so only include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This switches the Loongson driver over to using the bitops BIT()
macros and drops some local variables and make the code easier
to read (in my opinion).
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is pretty helpful to create some kind of device for backing the
GPIO chips, especially when preparing the driver for using
GENERIC_GPIO, so let's create a simple platform device and a simple
platform device driver and create the gpiochip in the .probe() routine
for the device driver. Keep all at the core initcall so the behaviour
is the same as before.
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver includes <linux/gpio.h> which is wrong, rely on
<linux/gpio/driver.h> and remove to call to gpio_set_value() in
favor of calling the internal function. Move functions around to
avoid forward declarations.
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Board files constitute a significant part of the users of the legacy
GPIO framework. In many cases they only export a line and set its
desired value. We could use GPIO hogs for that like we do for DT and
ACPI but there's no support for that in machine code.
This patch proposes to extend the machine.h API with support for
registering hog tables in board files.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Don't populate the const read-only array 'ports' on the stack but instead
make it static. Makes the object code smaller by over 100 buytes:
Before:
text data bss dec hex filename
10959 4952 832 16743 4167 drivers/gpio/gpio-104-dio-48e.o
After:
text data bss dec hex filename
10790 5008 832 16630 40f6 drivers/gpio/gpio-104-dio-48e.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch will toggle the EIC level to emulate the edge trigger to
support PMIC EIC egdge trigger function, which is required by gpio-keys
driver.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Spreadtrum debounce EIC and latch EIC can not support edge trigger,
but most GPIO users (like gpio-key driver) only use the edge trigger,
thus the EIC driver need add some support to emulate the edge trigger
to satisfy this requirement.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Geert Uytterhoeven pointed out that the number of register was a
fixed upper bound so there's no need to use a dynamically allocated
array in place of a VLA. Use the defined upper bound.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
The status handling code is actually a running regression from the
previous merge window which had an incomplete fix (now reverted) and
most of the remaining bug fixes are for problems older than the
current merge window"
[ Side note: this merge also takes the base kernel git repository to 6+
million objects for the first time. Technically we hit it a couple of
merges ago already if you count all the tag objects, but now it
reaches 6M+ objects reachable from HEAD.
I was joking around that that's when I should switch to 5.0, because
3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
probably not, even if numerology is about as good a reason as any.
- Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
scsi: aacraid: Insure command thread is not recursively stopped
scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
scsi: qla2xxx: correctly shift host byte
scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
scsi: qla2xxx: Avoid double completion of abort command
scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
scsi: scsi_dh: Don't look for NULL devices handlers by name
scsi: core: remove redundant assignment to shost->use_blk_mq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by flex,
bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by flex,
bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: extend output of 'listnewconfig'
kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
Kbuild: fix # escaping in .cmd files for future Make
kbuild: deb-pkg: split generating packaging and build
kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
kbuild: rename *-asn1.[ch] to *.asn1.[ch]
kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
.gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
kbuild: add %.dtb.S and %.dtb to 'targets' automatically
kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
genksyms: generate lexer and parser during build instead of shipping
kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
.gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
kbuild: use HOSTLDFLAGS for single .c executables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
- Fix race condition in imx_thermal_probe() (Mikhail Lappo)
- Add cooling device's statistics in sysfs (Viresh Kumar)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add cooling device's statistics in sysfs
thermal: imx: Fix race condition in imx_thermal_probe()
|
