| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fix from Wei Liu:
"One patch from Chris to fix kexec on Hyper-V"
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: vmbus: Allow cleanup of VMBUS_CONNECT_CPU if disconnected
|
|
Pull vhost fixes from Michael Tsirkin:
"Fixes all over the place, most notably vhost scsi IO error fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost scsi: Add support for LUN resets.
vhost scsi: add lun parser helper
vhost scsi: fix cmd completion race
vhost scsi: alloc cmds per vq instead of session
vhost: add helper to check if a vq has been setup
vdpasim: fix "mac_pton" undefined error
swiotlb: using SIZE_MAX needs limits.h included
|
|
In newer versions of virtio-scsi we just reset the timer when an a
command times out, so TMFs are never sent for the cmd time out case.
However, in older kernels and for the TMF inject cases, we can still get
resets and we end up just failing immediately so the guest might see the
device get offlined and IO errors.
For the older kernel cases, we want the same end result as the
modern virtio-scsi driver where we let the lower levels fire their error
handling and handle the problem. And at the upper levels we want to
wait. This patch ties the LUN reset handling into the LIO TMF code which
will just wait for outstanding commands to complete like we are doing in
the modern virtio-scsi case.
Note: I did not handle the ABORT case to keep this simple. For ABORTs
LIO just waits on the cmd like how it does for the RESET case. If
an ABORT fails, the guest OS ends up escalating to LUN RESET, so in
the end we get the same behavior where we wait on the outstanding
cmds.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-6-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Move code to parse lun from req's lun_buf to helper, so tmf code
can use it in the next patch.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/1604986403-4931-5-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We might not do the final se_cmd put from vhost_scsi_complete_cmd_work.
When the last put happens a little later then we could race where
vhost_scsi_complete_cmd_work does vhost_signal, the guest runs and sends
more IO, and vhost_scsi_handle_vq runs but does not find any free cmds.
This patch has us delay completing the cmd until the last lio core ref
is dropped. We then know that once we signal to the guest that the cmd
is completed that if it queues a new command it will find a free cmd.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Link: https://lore.kernel.org/r/1604986403-4931-4-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We currently are limited to 256 cmds per session. This leads to problems
where if the user has increased virtqueue_size to more than 2 or
cmd_per_lun to more than 256 vhost_scsi_get_tag can fail and the guest
will get IO errors.
This patch moves the cmd allocation to per vq so we can easily match
whatever the user has specified for num_queues and
virtqueue_size/cmd_per_lun. It also makes it easier to control how much
memory we preallocate. For cases, where perf is not as important and
we can use the current defaults (1 vq and 128 cmds per vq) memory use
from preallocate cmds is cut in half. For cases, where we are willing
to use more memory for higher perf, cmd mem use will now increase as
the num queues and queue depth increases.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-3-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
This adds a helper check if a vq has been setup. The next patches
will use this when we move the vhost scsi cmd preallocation from per
session to per vq. In the per vq case, we only want to allocate cmds
for vqs that have actually been setup and not for all the possible
vqs.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/1604986403-4931-2-git-send-email-michael.christie@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
ERROR: modpost: "mac_pton" [drivers/vdpa/vdpa_sim/vdpa_sim.ko] undefined!
mac_pton() is defined in lib/net_utils.c and is not built if NET is not set.
Select GENERIC_NET_UTILS as vdpasim doesn't depend on NET.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://lore.kernel.org/r/20201113155706.599434-1-lvivier@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
|
|
Pull drm fixes from Dave Airlie:
"Nouveau fixes:
- atomic modesetting regression fix
- ttm pre-nv50 fix
- connector NULL ptr deref fix"
* tag 'drm-fixes-2020-11-16' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/kms/nv50-: Use atomic encoder callbacks everywhere
drm/nouveau/ttm: avoid using nouveau_drm.ttm.type_vram prior to nv50
drm/nouveau/kms: Fix NULL pointer dereference in nouveau_connector_detect_depth
|
|
- atomic modesetting regression fix
- ttm pre-nv50 fix
- connector NULL ptr deref fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv5D9p78MNN0OxVeRZxN8LDqcadJEGUEFCgWJQ6+_rjPuw@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc/whatever driver fixes for 5.10-rc4.
Nothing huge, lots of small fixes for reported issues:
- habanalabs driver fixes
- speakup driver fixes
- uio driver fixes
- virtio driver fix
- other tiny driver fixes
Full details are in the shortlog.
All of these have been in linux-next for a full week with no reported
issues"
* tag 'char-misc-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
uio: Fix use-after-free in uio_unregister_device()
firmware: xilinx: fix out-of-bounds access
nitro_enclaves: Fixup type and simplify logic of the poll mask setup
speakup ttyio: Do not schedule() in ttyio_in_nowait
speakup: Fix clearing selection in safe context
speakup: Fix var_id_t values and thus keymap
virtio: virtio_console: fix DMA memory allocation for rproc serial
habanalabs/gaudi: mask WDT error in QMAN
habanalabs/gaudi: move coresight mmu config
habanalabs: fix kernel pointer type
mei: protect mei_cl_mtu from null dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt fixes from Greg KH:
"Here are some small Thunderbolt and USB driver fixes for 5.10-rc4 to
solve some reported issues.
Nothing huge in here, just small things:
- thunderbolt memory leaks fixed and new device ids added
- revert of problem patch for the musb driver
- new quirks added for USB devices
- typec power supply fixes to resolve much reported problems about
charging notifications not working anymore
All except the cdc-acm driver quirk addition have been in linux-next
with no reported issues (the quirk patch was applied on Friday, and is
self-contained)"
* tag 'usb-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode
MAINTAINERS: add usb raw gadget entry
usb: typec: ucsi: Report power supply changes
xhci: hisilicon: fix refercence leak in xhci_histb_probe
Revert "usb: musb: convert to devm_platform_ioremap_resource_byname"
thunderbolt: Add support for Intel Tiger Lake-H
thunderbolt: Only configure USB4 wake for lane 0 adapters
thunderbolt: Add uaccess dependency to debugfs interface
thunderbolt: Fix memory leak if ida_simple_get() fails in enumerate_services()
thunderbolt: Add the missed ida_simple_remove() in ring_request_msix()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Cure the fallout from the MSI irqdomain overhaul which missed that
the Intel IOMMU does not register virtual function devices and
therefore never reaches the point where the MSI interrupt domain is
assigned. This made the VF devices use the non-remapped MSI domain
which is trapped by the IOMMU/remap unit
- Remove an extra space in the SGI_UV architecture type procfs output
for UV5
- Remove a unused function which was missed when removing the UV BAU
TLB shootdown handler"
* tag 'x86-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
iommu/vt-d: Cure VF irqdomain hickup
x86/platform/uv: Fix copied UV5 output archtype
x86/platform/uv: Drop last traces of uv_flush_tlb_others
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two small clk driver fixes:
- Make to_clk_regmap() inline to avoid compiler annoyance
- Fix critical clks on i.MX imx8m SoCs"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx8m: fix bus critical clk registration
clk: define to_clk_regmap() as inline function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix potential bufer overflow in pmbus/max20730 driver
- Fix locking issue in pmbus core
- Fix regression causing timeouts in applesmc driver
- Fix RPM calculation in pwm-fan driver
- Restrict counter visibility in amd_energy driver
* tag 'hwmon-for-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (amd_energy) modify the visibility of the counters
hwmon: (applesmc) Re-work SMC comms
hwmon: (pwm-fan) Fix RPM calculation
hwmon: (pmbus) Add mutex locking for sysfs reads
hwmon: (pmbus/max20730) use scnprintf() instead of snprintf()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small fixes, all in the embedded ufs driver subsystem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufshcd: Fix missing destroy_workqueue()
scsi: ufs: Try to save power mode change and UIC cmd completion timeout
scsi: ufs: Fix unbalanced scsi_block_reqs_cnt caused by ufshcd_hold()
|
|
It turns out that I forgot to go through and make sure that I converted all
encoder callbacks to use atomic_enable/atomic_disable(), so let's go and
actually do that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Fixes: 09838c4efe9a ("drm/nouveau/kms: Search for encoders' connectors properly")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pre-NV50 chipsets don't currently use the MMU subsystem that later
chipsets use, and type_vram is negative here, leading to an OOB memory
access.
This was previously guarded by a chipset check, restore that.
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 5839172f0980 ("drm/nouveau: explicitly specify caching to use")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This oops manifests itself on the following hardware:
01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 103M] (rev a1)
Oct 09 14:17:46 lp-sasha kernel: BUG: kernel NULL pointer dereference, address: 0000000000000000
Oct 09 14:17:46 lp-sasha kernel: #PF: supervisor read access in kernel mode
Oct 09 14:17:46 lp-sasha kernel: #PF: error_code(0x0000) - not-present page
Oct 09 14:17:46 lp-sasha kernel: PGD 0 P4D 0
Oct 09 14:17:46 lp-sasha kernel: Oops: 0000 [#1] SMP PTI
Oct 09 14:17:46 lp-sasha kernel: CPU: 1 PID: 191 Comm: systemd-udevd Not tainted 5.9.0-rc8-next-20201009 #38
Oct 09 14:17:46 lp-sasha kernel: Hardware name: Hewlett-Packard Compaq Presario CQ61 Notebook PC/306A, BIOS F.03 03/23/2009
Oct 09 14:17:46 lp-sasha kernel: RIP: 0010:nouveau_connector_detect_depth+0x71/0xc0 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: Code: 0a 00 00 48 8b 49 48 c7 87 b8 00 00 00 06 00 00 00 80 b9 4d 0a 00 00 00 75 1e 83 fa 41 75 05 48 85 c0 75 29 8b 81 10 0d 00 00 <39> 06 7c 25 f6 81 14 0d 00 00 02 75 b7 c3 80 b9 0c 0d 00 00 00 75
Oct 09 14:17:46 lp-sasha kernel: RSP: 0018:ffffc9000028f8c0 EFLAGS: 00010297
Oct 09 14:17:46 lp-sasha kernel: RAX: 0000000000014c08 RBX: ffff8880369d4000 RCX: ffff8880369d3000
Oct 09 14:17:46 lp-sasha kernel: RDX: 0000000000000040 RSI: 0000000000000000 RDI: ffff8880369d4000
Oct 09 14:17:46 lp-sasha kernel: RBP: ffff88800601cc00 R08: ffff8880051da298 R09: ffffffff8226201a
Oct 09 14:17:46 lp-sasha kernel: R10: ffff88800469aa80 R11: ffff888004c84ff8 R12: 0000000000000000
Oct 09 14:17:46 lp-sasha kernel: R13: ffff8880051da000 R14: 0000000000002000 R15: 0000000000000003
Oct 09 14:17:46 lp-sasha kernel: FS: 00007fd0192b3440(0000) GS:ffff8880bc900000(0000) knlGS:0000000000000000
Oct 09 14:17:46 lp-sasha kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Oct 09 14:17:46 lp-sasha kernel: CR2: 0000000000000000 CR3: 0000000004976000 CR4: 00000000000006e0
Oct 09 14:17:46 lp-sasha kernel: Call Trace:
Oct 09 14:17:46 lp-sasha kernel: nouveau_connector_get_modes+0x1e6/0x240 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: ? kfree+0xb9/0x240
Oct 09 14:17:46 lp-sasha kernel: ? drm_connector_list_iter_next+0x7c/0xa0
Oct 09 14:17:46 lp-sasha kernel: drm_helper_probe_single_connector_modes+0x1ba/0x7c0
Oct 09 14:17:46 lp-sasha kernel: drm_client_modeset_probe+0x27e/0x1360
Oct 09 14:17:46 lp-sasha kernel: ? nvif_object_sclass_put+0xc/0x20 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: ? nouveau_cli_init+0x3cc/0x440 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: ? ktime_get_mono_fast_ns+0x49/0xa0
Oct 09 14:17:46 lp-sasha kernel: ? nouveau_drm_open+0x4e/0x180 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: __drm_fb_helper_initial_config_and_unlock+0x3f/0x4a0
Oct 09 14:17:46 lp-sasha kernel: ? drm_file_alloc+0x18f/0x260
Oct 09 14:17:46 lp-sasha kernel: ? mutex_lock+0x9/0x40
Oct 09 14:17:46 lp-sasha kernel: ? drm_client_init+0x110/0x160
Oct 09 14:17:46 lp-sasha kernel: nouveau_fbcon_init+0x14d/0x1c0 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: nouveau_drm_device_init+0x1c0/0x880 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: nouveau_drm_probe+0x11a/0x1e0 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: pci_device_probe+0xcd/0x140
Oct 09 14:17:46 lp-sasha kernel: really_probe+0xd8/0x400
Oct 09 14:17:46 lp-sasha kernel: driver_probe_device+0x4a/0xa0
Oct 09 14:17:46 lp-sasha kernel: device_driver_attach+0x9c/0xc0
Oct 09 14:17:46 lp-sasha kernel: __driver_attach+0x6f/0x100
Oct 09 14:17:46 lp-sasha kernel: ? device_driver_attach+0xc0/0xc0
Oct 09 14:17:46 lp-sasha kernel: bus_for_each_dev+0x75/0xc0
Oct 09 14:17:46 lp-sasha kernel: bus_add_driver+0x106/0x1c0
Oct 09 14:17:46 lp-sasha kernel: driver_register+0x86/0xe0
Oct 09 14:17:46 lp-sasha kernel: ? 0xffffffffa044e000
Oct 09 14:17:46 lp-sasha kernel: do_one_initcall+0x48/0x1e0
Oct 09 14:17:46 lp-sasha kernel: ? _cond_resched+0x11/0x60
Oct 09 14:17:46 lp-sasha kernel: ? kmem_cache_alloc_trace+0x19c/0x1e0
Oct 09 14:17:46 lp-sasha kernel: do_init_module+0x57/0x220
Oct 09 14:17:46 lp-sasha kernel: __do_sys_finit_module+0xa0/0xe0
Oct 09 14:17:46 lp-sasha kernel: do_syscall_64+0x33/0x40
Oct 09 14:17:46 lp-sasha kernel: entry_SYSCALL_64_after_hwframe+0x44/0xa9
Oct 09 14:17:46 lp-sasha kernel: RIP: 0033:0x7fd01a060d5d
Oct 09 14:17:46 lp-sasha kernel: Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d e3 70 0c 00 f7 d8 64 89 01 48
Oct 09 14:17:46 lp-sasha kernel: RSP: 002b:00007ffc8ad38a98 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
Oct 09 14:17:46 lp-sasha kernel: RAX: ffffffffffffffda RBX: 0000563f6e7fd530 RCX: 00007fd01a060d5d
Oct 09 14:17:46 lp-sasha kernel: RDX: 0000000000000000 RSI: 00007fd01a19f95d RDI: 000000000000000f
Oct 09 14:17:46 lp-sasha kernel: RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000007
Oct 09 14:17:46 lp-sasha kernel: R10: 000000000000000f R11: 0000000000000246 R12: 00007fd01a19f95d
Oct 09 14:17:46 lp-sasha kernel: R13: 0000000000000000 R14: 0000563f6e7fbc10 R15: 0000563f6e7fd530
Oct 09 14:17:46 lp-sasha kernel: Modules linked in: nouveau(+) ttm xt_string xt_mark xt_LOG vgem v4l2_dv_timings uvcvideo ulpi udf ts_kmp ts_fsm ts_bm snd_aloop sil164 qat_dh895xccvf nf_nat_sip nf_nat_irc nf_nat_ftp nf_nat nf_log_ipv6 nf_log_ipv4 nf_log_common ltc2990 lcd intel_qat input_leds i2c_mux gspca_main videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_common videodev mc drivetemp cuse fuse crc_itu_t coretemp ch7006 ath5k ath algif_hash
Oct 09 14:17:46 lp-sasha kernel: CR2: 0000000000000000
Oct 09 14:17:46 lp-sasha kernel: ---[ end trace 0ddafe218ad30017 ]---
Oct 09 14:17:46 lp-sasha kernel: RIP: 0010:nouveau_connector_detect_depth+0x71/0xc0 [nouveau]
Oct 09 14:17:46 lp-sasha kernel: Code: 0a 00 00 48 8b 49 48 c7 87 b8 00 00 00 06 00 00 00 80 b9 4d 0a 00 00 00 75 1e 83 fa 41 75 05 48 85 c0 75 29 8b 81 10 0d 00 00 <39> 06 7c 25 f6 81 14 0d 00 00 02 75 b7 c3 80 b9 0c 0d 00 00 00 75
Oct 09 14:17:46 lp-sasha kernel: RSP: 0018:ffffc9000028f8c0 EFLAGS: 00010297
Oct 09 14:17:46 lp-sasha kernel: RAX: 0000000000014c08 RBX: ffff8880369d4000 RCX: ffff8880369d3000
Oct 09 14:17:46 lp-sasha kernel: RDX: 0000000000000040 RSI: 0000000000000000 RDI: ffff8880369d4000
Oct 09 14:17:46 lp-sasha kernel: RBP: ffff88800601cc00 R08: ffff8880051da298 R09: ffffffff8226201a
Oct 09 14:17:46 lp-sasha kernel: R10: ffff88800469aa80 R11: ffff888004c84ff8 R12: 0000000000000000
Oct 09 14:17:46 lp-sasha kernel: R13: ffff8880051da000 R14: 0000000000002000 R15: 0000000000000003
Oct 09 14:17:46 lp-sasha kernel: FS: 00007fd0192b3440(0000) GS:ffff8880bc900000(0000) knlGS:0000000000000000
Oct 09 14:17:46 lp-sasha kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Oct 09 14:17:46 lp-sasha kernel: CR2: 0000000000000000 CR3: 0000000004976000 CR4: 00000000000006e0
The disassembly:
Code: 0a 00 00 48 8b 49 48 c7 87 b8 00 00 00 06 00 00 00 80 b9 4d 0a 00 00 00 75 1e 83 fa 41 75 05 48 85 c0 75 29 8b 81 10 0d 00 00 <39> 06 7c 25 f6 81 14 0d 00 00 02 75 b7 c3 80 b9 0c 0d 00 00 00 75
All code
========
0: 0a 00 or (%rax),%al
2: 00 48 8b add %cl,-0x75(%rax)
5: 49 rex.WB
6: 48 c7 87 b8 00 00 00 movq $0x6,0xb8(%rdi)
d: 06 00 00 00
11: 80 b9 4d 0a 00 00 00 cmpb $0x0,0xa4d(%rcx)
18: 75 1e jne 0x38
1a: 83 fa 41 cmp $0x41,%edx
1d: 75 05 jne 0x24
1f: 48 85 c0 test %rax,%rax
22: 75 29 jne 0x4d
24: 8b 81 10 0d 00 00 mov 0xd10(%rcx),%eax
2a:* 39 06 cmp %eax,(%rsi) <-- trapping instruction
2c: 7c 25 jl 0x53
2e: f6 81 14 0d 00 00 02 testb $0x2,0xd14(%rcx)
35: 75 b7 jne 0xffffffffffffffee
37: c3 retq
38: 80 b9 0c 0d 00 00 00 cmpb $0x0,0xd0c(%rcx)
3f: 75 .byte 0x75
Code starting with the faulting instruction
===========================================
0: 39 06 cmp %eax,(%rsi)
2: 7c 25 jl 0x29
4: f6 81 14 0d 00 00 02 testb $0x2,0xd14(%rcx)
b: 75 b7 jne 0xffffffffffffffc4
d: c3 retq
e: 80 b9 0c 0d 00 00 00 cmpb $0x0,0xd0c(%rcx)
15: 75 .byte 0x75
objdump -SF --disassemble=nouveau_connector_detect_depth
[...]
if (nv_connector->edid &&
c85e1: 83 fa 41 cmp $0x41,%edx
c85e4: 75 05 jne c85eb <nouveau_connector_detect_depth+0x6b> (File Offset: 0xc866b)
c85e6: 48 85 c0 test %rax,%rax
c85e9: 75 29 jne c8614 <nouveau_connector_detect_depth+0x94> (File Offset: 0xc8694)
nv_connector->type == DCB_CONNECTOR_LVDS_SPWG)
duallink = ((u8 *)nv_connector->edid)[121] == 2;
else
duallink = mode->clock >= bios->fp.duallink_transition_clk;
if ((!duallink && (bios->fp.strapless_is_24bit & 1)) ||
c85eb: 8b 81 10 0d 00 00 mov 0xd10(%rcx),%eax
c85f1: 39 06 cmp %eax,(%rsi)
c85f3: 7c 25 jl c861a <nouveau_connector_detect_depth+0x9a> (File Offset: 0xc869a)
( duallink && (bios->fp.strapless_is_24bit & 2)))
c85f5: f6 81 14 0d 00 00 02 testb $0x2,0xd14(%rcx)
c85fc: 75 b7 jne c85b5 <nouveau_connector_detect_depth+0x35> (File Offset: 0xc8635)
connector->display_info.bpc = 8;
[...]
% scripts/faddr2line /lib/modules/5.9.0-rc8-next-20201009/kernel/drivers/gpu/drm/nouveau/nouveau.ko nouveau_connector_detect_depth+0x71/0xc0
nouveau_connector_detect_depth+0x71/0xc0:
nouveau_connector_detect_depth at /home/sasha/linux-next/drivers/gpu/drm/nouveau/nouveau_connector.c:891
It is actually line 889. See the disassembly below.
889 duallink = mode->clock >= bios->fp.duallink_transition_clk;
The NULL pointer being dereferenced is mode.
Git bisect has identified the following commit as bad:
f28e32d3906e drm/nouveau/kms: Don't change EDID when it hasn't actually changed
Here is the chain of events that causes the oops.
On entry to nouveau_connector_detect_lvds, edid is set to NULL. The call
to nouveau_connector_detect sets nv_connector->edid to valid memory,
with status set to connector_status_connected and the flow of execution
branching to the out label.
The subsequent call to nouveau_connector_set_edid erronously clears
nv_connector->edid, via the local edid pointer which remains set to NULL.
Fix this by setting edid to the value of the just acquired
nv_connector->edid and executing the body of nouveau_connector_set_edid
only if nv_connector->edid and edid point to different memory addresses
thus preventing nv_connector->edid from being turned into a dangling
pointer.
Fixes: f28e32d3906e ("drm/nouveau/kms: Don't change EDID when it hasn't actually changed")
Signed-off-by: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull block fixes from Jens Axboe:
"A few small fixes:
- NVMe pull request from Christoph:
- don't clear the read-only bit on a revalidate (Sagi Grimberg)
- nbd error case refcount leak (Christoph)
- loop/generic uevent fix (Christoph, Petr)"
* tag 'block-5.10-2020-11-13' of git://git.kernel.dk/linux-block:
loop: Fix occasional uevent drop
block: add a return value to set_capacity_revalidate_and_notify
nbd: fix a block_device refcount leak in nbd_release
nvme: fix incorrect behavior when BLKROSET is called by the user
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- fix Flexcan binding schema errors introduced in rc3
- fix an of_node ref counting error in of_dma_is_coherent
* tag 'devicetree-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clock: imx5: fix example
dt-bindings: can: fsl,flexcan.yaml: fix compatible for i.MX35 and i.MX53
dt-bindings: can: fsl,flexcan.yaml: fix fsl,stop-mode
of/address: Fix of_node memory leak in of_dma_is_coherent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"A bunch of pin control fixes for the v5.10 kernel series.
Nothing in particular to say about it, because they are all driver
fixes.
I'm happy that some AMD driver fixes are appearing, it's been an
undermaintained driver, and laptops have suffered.
Summary:
- Two fixes to the Intel pin controller drivers: fixing pull
resistance bias.
- Fix some invalid SSI pins on the Ingenic pin controller.
- Make sure the clock is enabled when requesting interrupts from the
Rockchip GPIO controller.
- Make sure IRQs are mapped when looking up the IRQ for a GPIO line
on the Rockchip GPIO Write.
- Two regmap initialization fixes for the MCP23s08.
- Fix a GPI-only prefix function problem on the Aspeed pin
controller.
- Disable the debounce filter correctly on the AMD pin controller.
- Correct the timer clock setting for the AMD debounce timer.
- Make the Qualcomm pin controller more cautious around the handling
of PDC-related GPIO interrupts.
- Fix the interrupt map in the Qualcomm SM8250 pin controller"
* tag 'pinctrl-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: sm8250: Specify PDC map
pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback
pinctrl: amd: use higher precision for 512 RtcClk
pinctrl: amd: fix incorrect way to disable debounce filter
pinctrl: aspeed: Fix GPI only function problem.
pinctrl: mcp23s08: Print error message when regmap init fails
pinctrl: mcp23s08: Use full chunk of memory for regmap configuration
pinctrl: rockchip: create irq mapping in gpio_to_irq
pinctrl: rockchip: enable gpio pclk for rockchip_gpio_to_irq
pinctrl: ingenic: Fix invalid SSI pins
pinctrl: intel: Set default bias in case no particular value given
pinctrl: intel: Fix 2 kOhm bias which is 833 Ohm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes I've collected with the help of Bartosz.
Nothing special about them: all are driver and kbuild fixes + some
documentation fixes:
- Tidy up a missed function call in the designware driver when
converting to gpiolib irqchip
- Fix some bitmasks in the Aspeed driver
- Fix some kerneldoc warnings and minor bugs in the improved
userspace API documentation
- Revert the revert of the OMAP fix for lost edge wakeup interrupts:
the fix needs to stay in
- Fix a compile error when deselecting the character device
- A bunch of IRQ fixes on the idio GPIO drivers
- Fix an off-by-one error in the SiFive GPIO driver"
* tag 'gpio-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sifive: Fix SiFive gpio probe
gpio: pcie-idio-24: Enable PEX8311 interrupts
gpio: pcie-idio-24: Fix IRQ Enable Register value
gpio: pcie-idio-24: Fix irq mask when masking
gpiolib: fix sysfs when cdev is not selected
Revert "Revert "gpio: omap: Fix lost edge wake-up interrupts""
gpio: uapi: clarify the meaning of 'empty' char arrays
gpio: uapi: remove whitespace
gpio: uapi: kernel-doc formatting improvements
gpio: uapi: comment consistency
gpio: uapi: fix kernel-doc warnings
gpio: aspeed: fix ast2600 bank properties
gpio: dwapb: Fix missing conversion to GPIO-lib-based IRQ-chip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- tmio: Fixup support for reset
- sdhci-of-esdhc: Extend erratum for pulse width to more broken HWs
- renesas_sdhi: Fix re-binding of drivers
* tag 'mmc-v5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
Revert "mmc: renesas_sdhi: workaround a regression when reinserting SD cards"
mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF
mmc: tmio: when resetting, reset DMA controller, too
mmc: sdhci-of-esdhc: Handle pulse width detection erratum for more SoCs
mmc: renesas_sdhi_core: Add missing tmio_mmc_host_free() at remove
|
|
Pull drm fixes from Dave Airlie:
"Nearly didn't send you a PR this week at all, but a few things
trickled in over the day, not a huge amount here, some i915, amdgpu
and a bunch of misc fixes. I have a couple of nouveau fixes
outstanding due to the PR having the wrong base, I'll figure it out
next week.
amdgpu:
- Pageflip fix for DCN3
- Declare TA firmware for green sardine
- Headless navi fix
i915:
- Pull phys pread/pwrite implementations to the backend
- Correctly set SFC capability for video engines
bridge:
- cdns Kconfig fix
hyperv_fb:
- fix missing include
gma500:
- oob access fix
mcde:
- unbalanced regulator fix"
* tag 'drm-fixes-2020-11-13' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: enable DCN for navi10 headless SKU
drm/amdgpu: add ta firmware load for green-sardine
drm/i915: Correctly set SFC capability for video engines
drm/i915/gem: Pull phys pread/pwrite implementations to the backend
drm/i915/gem: Allow backends to override pread implementation
drm/mcde: Fix unbalanced regulator
drm/gma500: Fix out-of-bounds access to struct drm_device.vblank[]
video: hyperv_fb: include vmalloc.h
drm: bridge: cdns: Kconfig: Switch over dependency to ARCH_K3
drm/amd/display: Add missing pflip irq
|
|
This patch limits the visibility to owner and groups only for the
energy counters exposed through the hwmon based amd_energy driver.
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20201112172159.8781-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Renesas R-Car and RZ/G SoCs have a firmware download mode over USB.
However, on reset a banner string is transmitted out which is not expected
to be echoed back and will corrupt the protocol.
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20201111131209.3977903-1-chris.brandt@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the ucsi power supply goes online/offline, and when the
power levels change, the power supply class needs to be
notified so it can inform the user space.
Fixes: 992a60ed0d5e ("usb: typec: ucsi: register with power_supply class")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vladimir Yerilov <openmindead@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201110120547.67922-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. We should decrease the usage count
whetever it succeeded or failed(maybe runtime of the device has
error, or device is in inaccessible state, or other error state).
If we do not call put operation to decrease the reference, it will
result in reference leak in xhci_histb_probe. Moreover, this
device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by jumping to error handling
branch.
Fixes: c508f41da0788 ("xhci: hisilicon: support HiSilicon STB xHCI host controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106122221.2304528-1-zhangqilong3@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2d30e408a2a6b3443d3232593e3d472584a3e9f8.
On Beaglebone Black, where each interface has 2 children:
musb-dsps 47401c00.usb: can't request region for resource [mem 0x47401800-0x474019ff]
musb-hdrc musb-hdrc.1: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.1 failed with error -16
musb-dsps 47401400.usb: can't request region for resource [mem 0x47401000-0x474011ff]
musb-hdrc musb-hdrc.0: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.0 failed with error -16
Before, devm_ioremap_resource() was called on "dev" ("musb-hdrc.0" or
"musb-hdrc.1"), after it is called on "&pdev->dev" ("47401400.usb" or
"47401c00.usb"), leading to a duplicate region request, which fails.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 2d30e408a2a6 ("usb: musb: convert to devm_platform_ioremap_resource_byname")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201112135900.3822599-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
AMD-TEE driver bug fixes
AMD-TEE driver keeps track of shared memory buffers and their
corresponding buffer id's in a global linked list. These buffers are
used to share data between x86 and AMD Secure Processor. This pull
request fixes issues related to maintaining mapped buffers in a shared
linked list.
* tag 'amdtee-fixes-for-5.10' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
Link: https://lore.kernel.org/r/20201109080809.GA3862873@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The recent changes to store the MSI irqdomain pointer in struct device
missed that Intel DMAR does not register virtual function devices. Due to
that a VF device gets the plain PCI-MSI domain assigned and then issues
compat MSI messages which get caught by the interrupt remapping unit.
Cure that by inheriting the irq domain from the physical function
device.
Ideally the irqdomain would be associated to the bus, but DMAR can have
multiple units and therefore irqdomains on a single bus. The VF 'bus' could
of course inherit the domain from the PF, but that'd be yet another x86
oddity.
Fixes: 85a8dfc57a0b ("iommm/vt-d: Store irq domain in struct device")
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Link: https://lore.kernel.org/r/draft-87eekymlpz.fsf@nanos.tec.linutronix.de
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.10-2020-11-12:
amdgpu:
- Pageflip fix for DCN3
- Declare TA firmware for green sardine
- Headless navi fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201113055512.3963-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Pull phys pread/pwrite implementations to the backend (Chris)
- Correctly set SFC capability for video engines (Venkata)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201113052551.GA1319429@intel.com
|
|
There is a NULL pointer crash when DCN disabled on headless SKU.
On normal SKU, the variable adev->ddev.mode_config.funcs is
initialized in dm_hw_init(), and it is fine to access it in
amdgpu_device_resume(). But on headless SKU, DCN is disabled,
the funcs variable is not initialized, then crash arises.
Enable DCN to fix this issue.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In preparation to enabling hdcp on green sardine.
[How]
Add green-sardine ta f/w loading in psp_v12
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One Kconfig fix for bridge/cdns, a missing include for hypervb_fb, an
out-of-bound access fix for gma500 and a unbalanced regulator fix for
mcde.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201112130726.qwtryqvgspmljkax@gilmour.lan
|
|
SFC capability of video engines is not set correctly because i915
is testing for incorrect bits.
Fixes: c5d3e39caa45 ("drm/i915: Engine discovery query")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106011842.36203-1-daniele.ceraolospurio@intel.com
(cherry picked from commit ad18fa0f5f052046cad96fee762b5c64f42dd86a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Move the specialised interactions with the physical GEM object from the
pread/pwrite ioctl handler into the phys backend.
Currently, if one is able to exhaust the entire aperture and then try to
pwrite into an object not backed by struct page, we accidentally invoked
the phys pwrite handler on a non-phys object; calamitous.
Fixes: c6790dc22312 ("drm/i915: Wean off drm_pci_alloc/drm_pci_free")
Testcase: igt/gem_pwrite/exhaustion
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20201105154934.16022-2-chris@chris-wilson.co.uk
(cherry picked from commit 852e1b3644817f071427b83859b889c788a0cf69)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
As there are more and more complicated interactions between the different
backing stores and userspace, push the control into the backends rather
than accumulate them all inside the ioctl handlers.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105154934.16022-1-chris@chris-wilson.co.uk
(cherry picked from commit 0049b688459b846f819b6e51c24cd0781fcfde41)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for
ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- fix out-of-order UDP packets when forwarding with UDP GSO fraglists
turned on:
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter
rules"
* tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
lan743x: fix use of uninitialized variable
net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO
net: udp: fix UDP header access on Fast/frag0 UDP GRO
devlink: Avoid overwriting port attributes of registered port
vrf: Fix fast path output packet handling with async Netfilter rules
cosa: Add missing kfree in error path of cosa_write
net: switch to the kernel.org patchwork instance
ch_ktls: stop the txq if reaches threshold
ch_ktls: tcb update fails sometimes
ch_ktls/cxgb4: handle partial tag alone SKBs
ch_ktls: don't free skb before sending FIN
ch_ktls: packet handling prior to start marker
ch_ktls: Correction in middle record handling
ch_ktls: missing handling of header alone
ch_ktls: Correction in trimmed_len calculation
cxgb4/ch_ktls: creating skbs causes panic
ch_ktls: Update cheksum information
ch_ktls: Correction in finding correct length
cxgb4/ch_ktls: decrypted bit is not enough
net/x25: Fix null-ptr-deref in x25_connect
...
|
|
Commit 716ad0986cbd ("loop: Switch to set_capacity_revalidate_and_notify")
causes an occasional drop of loop device uevent, which are no longer
triggered in loop_set_size() but in a different part of code.
Bug is reproducible with LTP test uevent01 [1]:
i=0; while true; do
i=$((i+1)); echo "== $i =="
lsmod |grep -q loop && rmmod -f loop
./uevent01 || break
done
Put back triggering through code called in loop_set_size().
Fix required to add yet another parameter to
set_capacity_revalidate_and_notify().
[1] https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/uevents/uevent01.c
[hch: rebased on a different change to the prototype of
set_capacity_revalidate_and_notify]
Cc: stable@vger.kernel.org # v5.9
Fixes: 716ad0986cbd ("loop: Switch to set_capacity_revalidate_and_notify")
Reported-by: <ltp@lists.linux.it>
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are mostly docmentation fixes and janitorial changes plus some
new device IDs and a new quirk.
Specifics:
- Fix documentation regarding GPIO properties (Andy Shevchenko)
- Fix spelling mistakes in ACPI documentation (Flavio Suligoi)
- Fix white space inconsistencies in ACPI code (Maximilian Luz)
- Fix string formatting in the ACPI Generic Event Device (GED) driver
(Nick Desaulniers)
- Add Intel Alder Lake device IDs to the ACPI drivers used by the
Dynamic Platform and Thermal Framework (Srinivas Pandruvada)
- Add lid-related DMI quirk for Medion Akoya E2228T to the ACPI
button driver (Hans de Goede)"
* tag 'acpi-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: DPTF: Support Alder Lake
Documentation: ACPI: fix spelling mistakes
ACPI: button: Add DMI quirk for Medion Akoya E2228T
ACPI: GED: fix -Wformat
ACPI: Fix whitespace inconsistencies
ACPI: scan: Fix acpi_dma_configure_id() kerneldoc name
Documentation: firmware-guide: gpio-properties: Clarify initial output state
Documentation: firmware-guide: gpio-properties: active_low only for GpioIo()
Documentation: firmware-guide: gpio-properties: Fix factual mistakes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Make the intel_pstate driver behave as expected when it operates in
the passive mode with HWP enabled and the 'powersave' governor on top
of it"
* tag 'pm-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Take CPUFREQ_GOV_STRICT_TARGET into account
cpufreq: Add strict_target to struct cpufreq_policy
cpufreq: Introduce CPUFREQ_GOV_STRICT_TARGET
cpufreq: Introduce governor flags
|
|
When no devicetree is present, the driver will use an
uninitialized variable.
Fix by initializing this variable.
Fixes: 902a66e08cea ("lan743x: correctly handle chips with internal PHY")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112152513.1941-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-11-10
This series contains updates to i40e and igc drivers and the MAINTAINERS
file.
Slawomir fixes updating VF MAC addresses to fix various issues related
to reporting and setting of these addresses for i40e.
Dan Carpenter fixes a possible used before being initialized issue for
i40e.
Vinicius fixes reporting of netdev stats for igc.
Tony updates repositories for Intel Ethernet Drivers.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
MAINTAINERS: Update repositories for Intel Ethernet Drivers
igc: Fix returning wrong statistics
i40e, xsk: uninitialized variable in i40e_clean_rx_irq_zc()
i40e: Fix MAC address setting for a VF via Host/VM
====================
Link: https://lore.kernel.org/r/20201111001955.533210-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VRF devices use an optimized direct path on output if a default qdisc
is involved, calling Netfilter hooks directly. This path, however, does
not consider Netfilter rules completing asynchronously, such as with
NFQUEUE. The Netfilter okfn() is called for asynchronously accepted
packets, but the VRF never passes that packet down the stack to send
it out over the slave device. Using the slower redirect path for this
seems not feasible, as we do not know beforehand if a Netfilter hook
has asynchronously completing rules.
Fix the use of asynchronously completing Netfilter rules in OUTPUT and
POSTROUTING by using a special completion function that additionally
calls dst_output() to pass the packet down the stack. Also, slightly
adjust the use of nf_reset_ct() so that is called in the asynchronous
case, too.
Fixes: dcdd43c41e60 ("net: vrf: performance improvements for IPv4")
Fixes: a9ec54d1b0cd ("net: vrf: performance improvements for IPv6")
Signed-off-by: Martin Willi <martin@strongswan.org>
Link: https://lore.kernel.org/r/20201106073030.3974927-1-martin@strongswan.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
* acpi-scan:
ACPI: scan: Fix acpi_dma_configure_id() kerneldoc name
* acpi-misc:
ACPI: GED: fix -Wformat
ACPI: Fix whitespace inconsistencies
* acpi-button:
ACPI: button: Add DMI quirk for Medion Akoya E2228T
* acpi-dptf:
ACPI: DPTF: Support Alder Lake
|
