| Age | Commit message (Collapse) | Author |
|---|
|
Configure the burst length in Ethernet drivers. This improves
Ethernet performance by 58%. According to the vendor BSP,
8W burst length is supported by ar9 and newer SoCs.
The NAT benchmark results on xRX200 (Down/Up):
* 2W: 330 Mb/s
* 4W: 432 Mb/s 372 Mb/s
* 8W: 520 Mb/s 389 Mb/s
Tested on xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new firmware supports to divides the whole multicast MAC address space
equally to functions of all PFs, and calculates the space size of each PF
according to its function number.
To support this feature, PF driver adds querying multicast MAC address
space size from firmware and limits used number according to space size.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, there are two ways for PF to set the unicast MAC address space
size: specified by config parameters in firmware or set to default value.
That's mean if the config parameters in firmware is zero, driver will
divide the whole unicast MAC address space equally to 8 PFs. However, in
this case, the unicast MAC address space will be wasted a lot when the
hardware actually has less then 8 PFs. And in the other hand, if one PF has
much more VFs than other PFs, then each function of this PF will has much
less address space than other PFs.
In order to ameliorate the above two situations, introduce the third way
of unicast MAC address space assignment: firmware divides the whole unicast
MAC address space equally to functions of all PFs, and calculates the space
size of each PF according to its function number. PF queries the space size
by the querying device specification command when in initialization
process.
The third way assignment is lower priority than specified by config
parameters, only if the config parameters is zero can be used, and if
firmware does not support the third way assignment, then driver still
divides the whole unicast MAC address space equally to 8 PFs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed "stdbool.h" inclusion in iosm_ipc_imem.h
Fixes: 13bb8429ca98 ("net: wwan: iosm: firmware flashing and coredump collection")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and WP
Also correct how initialize_dco_operating_mode is called
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we don't need to support new 5.2 functions but different register
addresses
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not need since TCS firmware file will configure it properlly.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a follow-up to beb401ec5006 ("r8169: deprecate support for
RTL_GIGA_MAC_VER_27") that came with 5.12. Nobody complained, so let's
remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below.
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/netiucv.c:1852: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/lcs.c:2355: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/ctcm_main.c:979: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not used anymore, remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newly introduced PMTDB register is there to provide all needed info
about particular requested port split configuration. Use it instead of
figuring the info out manually in the driver.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PMTDB register allows to query the possible module<->local port
mapping than can be used in PMLP. It does not represent the actual/current
mapping of the local to module. Actual mapping is only defined by PMLP.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on the values coming from the PMLP register, use PLLP
to get the information about port front panel number and split number.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PLLP register returns the mapping from Local Port into Label Port.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During port creation, mlxsw_core_port_init() is called with the front
panel port number and the split port sub-number. Currently, this
information is determined by the driver without firmware assistance.
Subsequent patches are going to query this information from firmware,
but this requires the port to assigned to SWID.
Therefore, move port SWID assignment before mlxsw_core_port_init().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During port creation, mlxsw_core_port_init() is called with the front
panel port number and the split port sub-number. Currently, this
information is determined by the driver without firmware assistance.
Subsequent patches are going to query this information from firmware,
but this requires the port to be mapped to a module.
Therefore, move port mapping before mlxsw_core_port_init().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add latest verified version of Nvidia Spectrum-family switch firmware,
for Spectrum (13.2008.3326), Spectrum-2 (29.2008.3326) and Spectrum-3
(30.2008.3326).
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch brings-in support for M.2 7560 Device firmware flashing &
coredump collection using devlink.
- Driver Registers with Devlink framework.
- Register devlink params callback for configuring device params
required in flashing or coredump flow.
- Implements devlink ops flash_update callback that programs modem
firmware.
- Creates region & snapshot required for device coredump log collection.
On early detection of device in boot rom stage. Driver registers with
Devlink framework and establish transport channel for PSI (Primary Signed
Image) injection. Once PSI is injected to device, the device execution
stage details are read to determine whether device is in flash or
exception mode. The collected information is reported to devlink user
space application & based on this informationi, application proceeds with
either modem firmware flashing or coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nci_skb_alloc() already prints an error message on memory allocation
failure.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfc_mei_phy_alloc() already prints an error message on memory allocation
failure.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfc_mei_phy_alloc() already prints an error message on memory allocation
failure.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print error message with reference to a device.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it was reported and discussed in: https://lore.kernel.org/lkml/CAHk-=whF9F89vsfH8E9TGc0tZA-yhzi2Di8wOtquNB5vRkFX5w@mail.gmail.com/
This patch improves the stack space of qede_config_rx_mode() by
splitting filter_config() to 3 functions and removing the
union qed_filter_type_params.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add Mediatek MT7986 & MT8195 wdt support
- add Maxim MAX63xx
- drop bd70528 support
- rewrite ixp4xx to watchdog framework
- constify static struct watchdog_ops for sl28cpld_wdt, mpc8xxx_wdt and
tqmx86
- introduce watchdog_dev_suspend/resume
- several fixes and improvements
* tag 'linux-watchdog-5.15-rc1' of git://www.linux-watchdog.org/linux-watchdog:
dt-bindings: watchdog: Add compatible for Mediatek MT7986
watchdog: ixp4xx: Rewrite driver to use core
watchdog: Start watchdog in watchdog_set_last_hw_keepalive only if appropriate
watchdog: max63xx_wdt: Add device tree probing
dt-bindings: watchdog: Add Maxim MAX63xx bindings
watchdog: mediatek: mt8195: add wdt support
dt-bindings: reset: mt8195: add toprgu reset-controller header file
watchdog: tqmx86: Constify static struct watchdog_ops
watchdog: mpc8xxx_wdt: Constify static struct watchdog_ops
watchdog: sl28cpld_wdt: Constify static struct watchdog_ops
watchdog: iTCO_wdt: Fix detection of SMI-off case
watchdog: bcm2835_wdt: consider system-power-controller property
watchdog: imx2_wdg: notify wdog core to stop ping worker on suspend
watchdog: introduce watchdog_dev_suspend/resume
watchdog: Fix NULL pointer dereference when releasing cdev
watchdog: only run driver set_pretimeout op if device supports it
watchdog: bd70528 drop bd70528 support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi fix from Jean Delvare.
Unbreak some existing udev/hwdb modalias matches due to misplaced
product_sku field.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Move product_sku info to the end of the modalias
|
|
Pull NTB updates from Jon Mason:
"Bug fixes and clean-ups for Linux v5.15"
* tag 'ntb-5.15' of git://github.com/jonmason/ntb:
NTB: switch from 'pci_' to 'dma_' API
ntb: ntb_pingpong: remove redundant initialization of variables msg_data and spad_data
NTB: perf: Fix an error code in perf_setup_inbuf()
NTB: Fix an error code in ntb_msit_probe()
ntb: intel: remove invalid email address in header comment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- move the crash recovery worker to the freezable work queue to avoid
interaction with other drivers during suspend & resume
- fix a couple of typos in comments
- add support for handling the audio DSP on SDM660
- fix a race between the Qualcomm wireless subsystem driver and the
associated driver for the RF chip
* tag 'rproc-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: q6v5_pas: Add sdm660 ADSP PIL compatible
dt-bindings: remoteproc: qcom: adsp: Add SDM660 ADSP
remoteproc: use freezable workqueue for crash notifications
remoteproc: fix kernel doc for struct rproc_ops
remoteproc: fix an typo in fw_elf_get_class code comments
remoteproc: qcom: wcnss: Fix race with iris probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Fix-ups:
- Improve bootloader/kernel device handover
Bug Fixes:
- Stabilise backlight in ktd253 driver"
* tag 'backlight-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Improve bootloader/kernel device handover
backlight: ktd253: Stabilize backlight
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for registering devices via MFD cells to Simple MFD (I2C)
New Drivers:
- Add support for Renesas Synchronization Management Unit (SMU)
New Device Support:
- Add support for N5010 to Intel M10 BMC
- Add support for Cannon Lake to Intel LPSS ACPI
- Add support for Samsung SSG{1,2} to ST-Ericsson's U8500 family
- Add support for TQMx110EB and TQMxE40x to TQ-Systems PLD TQMx86
New Functionality:
- Add support for GPIO to Intel LPC ICH
- Add support for Reset to Texas Instruments TPS65086
Fix-ups:
- Trivial, sorting, whitespace, renaming, etc; mt6360-core, db8500-prcmu-regs, tqmx86
- Device Tree fiddling; syscon, axp20x, qcom,pm8008, ti,tps65086, brcm,cru
- Use proper APIs for IRQ map resolution; ab8500-core, stmpe, tc3589x, wm8994-irq
- Pass 'supplied-from' property through axp288_fuel_gauge via swnode
- Remove unused file entry; MAINTAINERS
- Make interrupt line optional; tps65086
- Rename db8500-cpuidle driver symbol; db8500-prcmu
- Remove support for unused hardware; tqmx86
- Provide a standard LPC clock frequency for unknown boards; tqmx86
- Remove unused code; ti_am335x_tscadc
- Use of_iomap() instead of ioremap(); syscon
Bug Fixes:
- Clear GPIO IRQ resource flags when no IRQ is set; tqmx86
- Fix incorrect/misleading frequencies; db8500-prcmu
- Mitigate namespace clash with other GPIOBASE users"
* tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (31 commits)
mfd: lpc_sch: Rename GPIOBASE to prevent build error
mfd: syscon: Use of_iomap() instead of ioremap()
dt-bindings: mfd: Add Broadcom CRU
mfd: ti_am335x_tscadc: Delete superfluous error message
mfd: tqmx86: Assume 24MHz LPC clock for unknown boards
mfd: tqmx86: Add support for TQ-Systems DMI IDs
mfd: tqmx86: Add support for TQMx110EB and TQMxE40x
mfd: tqmx86: Fix typo in "platform"
mfd: tqmx86: Remove incorrect TQMx90UC board ID
mfd: tqmx86: Clear GPIO IRQ resource when no IRQ is set
mfd: simple-mfd-i2c: Add support for registering devices via MFD cells
mfd/cpuidle: ux500: Rename driver symbol
mfd: tps65086: Add cell entry for reset driver
mfd: tps65086: Make interrupt line optional
dt-bindings: mfd: Convert tps65086.txt to YAML
MAINTAINERS: Adjust ARM/NOMADIK/Ux500 ARCHITECTURES to file renaming
mfd: db8500-prcmu: Handle missing FW variant
mfd: db8500-prcmu: Rename register header
mfd: axp20x: Add supplied-from property to axp288_fuel_gauge cell
mfd: Don't use irq_create_mapping() to resolve a mapping
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We mostly have various improvements and refactoring all over the place
but also some interesting new features - like the virtio GPIO driver
that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
driver for rockchip - this one has been split out of the pinctrl
driver.
Summary:
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the
driver and use generic device property interfaces, improve property
sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO
banks per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent
within its header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in
gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers"
* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
gpio: viperboard: remove platform_set_drvdata() call in probe
gpio: virtio: Add missing mailings lists in MAINTAINERS entry
gpio: virtio: Fix sparse warnings
gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
gpio: max730x: Use the right include
gpio: Add virtio-gpio driver
gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
gpio: mlxbf2: Use devm_platform_ioremap_resource()
gpio: mlxbf2: Drop wrong use of ACPI_PTR()
gpio: mlxbf2: Convert to device PM ops
gpio: dwapb: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
gpio: dwapb: Read GPIO base from gpio-base property
gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
gpiolib: Deduplicate forward declaration in the consumer.h header
MAINTAINERS: update gpio-zynq.yaml reference
gpio: tegra186: Add ACPI support
...
|
|
We can reproduce this issue with below steps:
1) enable WoL on the host
2) host system suspended
3) remote client send out wakeup packets
We can see that host system resume back, but can't work, such as ping failed.
After a bit digging, this issue is introduced by the commit 46f69ded988d
("net: stmmac: Use resolved link config in mac_link_up()"), which use
the finalised link parameters in mac_link_up() rather than the
parameters in mac_config().
There are two scenarios for MAC suspend/resume in STMMAC driver:
1) MAC suspend with WoL inactive, stmmac_suspend() call
phylink_mac_change() to notify phylink machine that a change in MAC
state, then .mac_link_down callback would be invoked. Further, it will
call phylink_stop() to stop the phylink instance. When MAC resume back,
firstly phylink_start() is called to start the phylink instance, then
call phylink_mac_change() which will finally trigger phylink machine to
invoke .mac_config and .mac_link_up callback. All is fine since
configuration in these two callbacks will be initialized, that means MAC
can restore the state.
2) MAC suspend with WoL active, phylink_mac_change() will put link
down, but there is no phylink_stop() to stop the phylink instance, so it
will link up again, that means .mac_config and .mac_link_up would be
invoked before system suspended. After system resume back, it will do
DMA initialization and SW reset which let MAC lost the hardware setting
(i.e MAC_Configuration register(offset 0x0) is reset). Since link is up
before system suspended, so .mac_link_up would not be invoked after
system resume back, lead to there is no chance to initialize the
configuration in .mac_link_up callback, as a result, MAC can't work any
longer.
After discussed with Russell King [1], we confirm that phylink framework
have not take WoL into consideration yet. This patch calls
phylink_suspend()/phylink_resume() functions which is newly introduced
by Russell King to fix this issue.
[1] https://lore.kernel.org/netdev/20210901090228.11308-1-qiangqing.zhang@nxp.com/
Fixes: 46f69ded988d ("net: stmmac: Use resolved link config in mac_link_up()")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The parameter bond_params is a relatively large 192 byte sized
struct so pass it by reference rather than by value to reduce
copying.
Addresses-Coverity: ("Big parameter passed by value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
linux-can-fixes-for-5.15-20210907
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.15
First set of fixes for v5.15 and only iwlwifi patches this time. Most
important being support for new hardware and new firmware API.
I had already earlier applied a fix which also Linus applied to this
tree as commit 1476ff21abb4 ("iwl: fix debug printf format strings"),
but this doesn't seem to cause any conflicts so I left it there.
iwlwifi
* add support for firmware API 66
* add support for Samsung Galaxy Book Flex2 Alpha
* fix a leak happening every time module is loaded
* fix a printk compiler warning
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing the driver module w/o bringing an interface up before
the error below occurs. Reason seems to be that cancel_work_sync() is
called in t3_sge_stop() for a queue that hasn't been initialized yet.
[10085.941785] ------------[ cut here ]------------
[10085.941799] WARNING: CPU: 1 PID: 5850 at kernel/workqueue.c:3074 __flush_work+0x3ff/0x480
[10085.941819] Modules linked in: vfat snd_hda_codec_hdmi fat snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio led_class ee1004 iTCO_
wdt intel_tcc_cooling x86_pkg_temp_thermal coretemp aesni_intel crypto_simd cryptd snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hda_core r
8169 snd_pcm realtek mdio_devres snd_timer snd i2c_i801 i2c_smbus libphy i915 i2c_algo_bit cxgb3(-) intel_gtt ttm mdio drm_kms_helper mei_me s
yscopyarea sysfillrect sysimgblt mei fb_sys_fops acpi_pad sch_fq_codel crypto_user drm efivarfs ext4 mbcache jbd2 crc32c_intel
[10085.941944] CPU: 1 PID: 5850 Comm: rmmod Not tainted 5.14.0-rc7-next-20210826+ #6
[10085.941974] Hardware name: System manufacturer System Product Name/PRIME H310I-PLUS, BIOS 2603 10/21/2019
[10085.941992] RIP: 0010:__flush_work+0x3ff/0x480
[10085.942003] Code: c0 74 6b 65 ff 0d d1 bd 78 75 e8 bc 2f 06 00 48 c7 c6 68 b1 88 8a 48 c7 c7 e0 5f b4 8b 45 31 ff e8 e6 66 04 00 e9 4b fe ff ff <0f> 0b 45 31 ff e9 41 fe ff ff e8 72 c1 79 00 85 c0 74 87 80 3d 22
[10085.942036] RSP: 0018:ffffa1744383fc08 EFLAGS: 00010246
[10085.942048] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000923
[10085.942062] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff91c901710a88
[10085.942076] RBP: ffffa1744383fce8 R08: 0000000000000001 R09: 0000000000000001
[10085.942090] R10: 00000000000000c2 R11: 0000000000000000 R12: ffff91c901710a88
[10085.942104] R13: 0000000000000000 R14: ffff91c909a96100 R15: 0000000000000001
[10085.942118] FS: 00007fe417837740(0000) GS:ffff91c969d00000(0000) knlGS:0000000000000000
[10085.942134] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10085.942146] CR2: 000055a8d567ecd8 CR3: 0000000121690003 CR4: 00000000003706e0
[10085.942160] Call Trace:
[10085.942166] ? __lock_acquire+0x3af/0x22e0
[10085.942177] ? cancel_work_sync+0xb/0x10
[10085.942187] __cancel_work_timer+0x128/0x1b0
[10085.942197] ? __pm_runtime_resume+0x5b/0x90
[10085.942208] cancel_work_sync+0xb/0x10
[10085.942217] t3_sge_stop+0x2f/0x50 [cxgb3]
[10085.942234] remove_one+0x26/0x190 [cxgb3]
[10085.942248] pci_device_remove+0x39/0xa0
[10085.942258] __device_release_driver+0x15e/0x240
[10085.942269] driver_detach+0xd9/0x120
[10085.942278] bus_remove_driver+0x53/0xd0
[10085.942288] driver_unregister+0x2c/0x50
[10085.942298] pci_unregister_driver+0x31/0x90
[10085.942307] cxgb3_cleanup_module+0x10/0x18c [cxgb3]
[10085.942324] __do_sys_delete_module+0x191/0x250
[10085.942336] ? syscall_enter_from_user_mode+0x21/0x60
[10085.942347] ? trace_hardirqs_on+0x2a/0xe0
[10085.942357] __x64_sys_delete_module+0x13/0x20
[10085.942368] do_syscall_64+0x40/0x90
[10085.942377] entry_SYSCALL_64_after_hwframe+0x44/0xae
[10085.942389] RIP: 0033:0x7fe41796323b
Fixes: 5e0b8928927f ("net:cxgb3: replace tasklets with works")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d3a ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This automatically selects between ioremap() and ioremap_np() on
platforms that require it, such as Apple SoCs.
Signed-off-by: Hector Martin <marcan@marcan.st>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The pdev maybe not a platform device, e.g. c_can_pci device, in this
case, calling to_platform_device() would not make sense. Also, per the
comment in drivers/net/can/c_can/c_can_ethtool.c, @bus_info should
match dev_name() string, so I am replacing this with dev_name() to fix
this issue.
[ 1.458583] BUG: unable to handle page fault for address: 0000000100000000
[ 1.460921] RIP: 0010:strnlen+0x1a/0x30
[ 1.466336] ? c_can_get_drvinfo+0x65/0xb0 [c_can]
[ 1.466597] ethtool_get_drvinfo+0xae/0x360
[ 1.466826] dev_ethtool+0x10f8/0x2970
[ 1.467880] sock_ioctl+0xef/0x300
Fixes: 2722ac986e93 ("can: c_can: add ethtool support")
Link: https://lore.kernel.org/r/20210906233704.1162666-1-ztong0001@gmail.com
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since commit
| dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
the rcar_canfd driver can be compile tested on all architectures. On
non OF enabled archs, or archs where OF is optional (and disabled in
the .config) the compilation throws the following warning:
| drivers/net/can/rcar/rcar_canfd.c:2020:34: warning: unused variable 'rcar_canfd_of_table' [-Wunused-const-variable]
| static const struct of_device_id rcar_canfd_of_table[] = {
| ^
This patch fixes the warning by marking the variable
rcar_canfd_of_table as __maybe_unused.
Fixes: ac4224087312 ("can: rcar: Kconfig: Add helper dependency on COMPILE_TEST")
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Link: https://lore.kernel.org/all/20210907064537.1054268-1-mkl@pengutronix.de
Cc: linux-renesas-soc@vger.kernel.org
Cc: Cai Huoqing <caihuoqing@baidu.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
