| Age | Commit message (Collapse) | Author |
|---|
|
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phy_write_paged() in m88e1118_config_init() to set the MSCR value.
We leave the other paged write for the LEDs in case the DT register
parsing is relying on this page.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Locally generated packets ingress the device through its CPU port. When
the CPU port is congested and there are not enough credits in its
headroom buffer, packets can be dropped.
While this might be acceptable for data packets that traverse the
network, configuration packets exchanged between the host and the device
(EMADs) should not be subjected to this flow control.
The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the
host to instruct the device to treat packets sent on this queue as
"local processing" and always process them, regardless of the state of
the CPU port's headroom.
Add the definition of this bit and set it for the dedicated SDQ reserved
for the transmission of EMAD packets. This makes the "local processing"
bit in the WQE (Work Queue Element) redundant, so clear it.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-01-05
this is a pull request of 15 patches for net-next/master.
The first patch is by me and removed an unused variable from the
usb_8dev driver.
Andy Shevchenko contributes a patch for the mcp251x driver, which
removes an unneeded assignment.
Jimmy Assarsson's patch for the kvaser_usb makes use of units.h in the
assignment of frequencies.
Lad Prabhakar provides 2 patches, converting the ti_hecc and the
sja1000 driver to make use of platform_get_irq().
The 10 remaining patches are by Vincent Mailhol. First the etas_es58x
driver populates the net_device::dev_port. The next 5 patches cleanup
the handling of CAN error and CAN RTR messages of all drivers. The
remaining 4 patches enhance the CAN controller mode flag handling and
export it via netlink to user space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently PF and VF use two sets of command code for modules to interact
with firmware. These codes values are same espect the macro names. It is
redundent to keep two sets of command code for same functions between PF
and VF.
So this patch firstly creates a unified command code for PF and VF module.
We keep the macro name same with the PF command code name to avoid too many
meaningless modifications. Secondly the new common command codes are used
to replace the old ones in VF and deletes the old ones.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch firstly uses new tqp struct(hclge_comm_tqp) and removes the
old VF tqp struct(hclgevf_tqp). All the tqp stats members used in VF module
are modified according to the new hclge_comm_tqp.
Secondly VF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch firstly uses new tqp struct(hclge_comm_tqp) and deletes the
old PF tqp struct(hclge_tqp). All the tqp stats members used in PF module
are modified according to the new hclge_comm_tqp.
Secondly PF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates new set of common tqp stats structures and APIs for PF
and VF tqp stats module. Subfunctions such as get tqp stats, update tqp
stats and reset tqp stats are inclued in this patch.
These new common tqp stats APIs will be used to replace the old PF and VF
tqp stats APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses common rss init APIs to replace the old APIs in VF rss
module and removes the old VF rss init APIs. Several related Subfunctions
and macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses common rss init APIs to replace the old APIs in PF rss
module and deletes the old PF rss init APIs. Some related subfunctions and
macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates new set of common rss init APIs for PF and VF rss
module. Subfunctions called by rss init process are also created include
rss tuple configuration and rss indirect table configuration.
These new common rss init APIs will be used to replace the old PF and VF
rss init APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses new common rss set APIs to replace the old APIs in VF rss
module and removes those old rss set APIs. The related macros in VF are
also modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses new common rss set APIs to replace the old APIs in PF rss
module and deletes the old rss set APIs. The related macros are also
modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hns3 PF and VF rss module have two sets of rss set APIs to
configure rss. There is no need to keep two sets of these same APIs.
So this patch creates new set of common rss set APIs for PF and VF reuse.
These new APIs will be used to unify old APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclgevf_dev and deletes the original child rss parameter
member(hclgevf_rss_cfg). All the rss parameter members used in VF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly VF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclge_dev and deletes the original child rss parameter
members in vport. All the vport child rss parameter members used in PF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly PF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PF and VF rss get APIs are almost the same espect the suffixes of API
names. These same impementions bring double development and bugfix work.
So this patch creates new common rss get APIs for PF and VF rss module.
Subfunctions called by rss query process are also created(e.g. rss tuple
conversion APIs).
These new common rss get APIs will be used to replace PF and VF old rss
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, there are two different sets of special command codes in PF and
VF cmdq modules, this is because VF driver only uses small part of all the
command codes. In other words, these not used command codes in VF are also
sepcial command codes theoretically.
So this patch unifes the special command codes and deletes the bool param
is_pf of hclge_comm_send. All the related functions are refactored
according to the new hclge_comm_send function prototype.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently PF stores its rss parameters in vport structure. VF stores rss
configurations in hclgevf_rss_cfg structure. Actually hns3 rss parameters
are same beween PF and VF. The two set of rss parameters are redundent and
may add extra bugfix work.
So this patch creates new common rss parameter struct(hclge_comm_rss_cfg)
to unify PF and VF rss configurations.
These new structures will be used to unify rss configurations in PF and VF
rss APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend lan966x driver with mdb support by implementing the switchdev
calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB.
It is allowed to add both ipv4/ipv6 entries and l2 entries. To add
ipv4/ipv6 entries is not required to use the PGID table while for l2
entries it is required. The PGID table is much smaller than MAC table
so only fewer l2 entries can be added.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first entries in the PGID table are used by the front ports while
the last entries are used for different purposes like flooding mask,
copy to CPU, etc. So add these macros to define which entries can be
used for general purpose.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend mac functionality with the function lan966x_mac_ip_learn. This
function adds an entry in the MAC table for IP multicast addresses.
These entries can copy a frame to the CPU but also can forward on the
front ports.
This functionality is needed for mdb support. In case the CPU and some
of the front ports subscribe to an IP multicast address.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement read and write access to IEEE 802.3 Clause 45 Ethernet
phy registers while making use of new mdiobus_c45_regad and
mdiobus_c45_devad helpers.
Tested on the Ubiquiti UniFi 6 LR access point featuring
MediaTek MT7622BV WiSoC with Aquantia AQR112C.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of returning -1 (-EPERM) when MDIO bus is stuck busy
while writing or 0xffff if it happens while reading, return the
appropriate -ETIMEDOUT. Also fix return type to int instead of u32.
Refactor functions to use bitfield helpers instead of having various
masking and shifting constants in the code, which also results in the
register definitions in the header file being more obviously related
to what is stated in the MediaTek's Reference Manual.
Fixes: 656e705243fd0 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the CAN netlink interface provides no easy ways to check
the capabilities of a given controller. The only method from the
command line is to try each CAN_CTRLMODE_* individually to check
whether the netlink interface returns an -EOPNOTSUPP error or not
(alternatively, one may find it easier to directly check the source
code of the driver instead...)
This patch introduces a method for the user to check both the
supported and the static capabilities. The proposed method introduces
a new IFLA nest: IFLA_CAN_CTRLMODE_EXT which extends the current
IFLA_CAN_CTRLMODE. This is done to guaranty a full forward and
backward compatibility between the kernel and the user land
applications.
The IFLA_CAN_CTRLMODE_EXT nest contains one single entry:
IFLA_CAN_CTRLMODE_SUPPORTED. Because this entry is only used in one
direction: kernel to userland, no new struct nla_policy are
introduced.
Below table explains how IFLA_CAN_CTRLMODE_SUPPORTED (hereafter:
"supported") and can_ctrlmode::flags (hereafter: "flags") allow us to
identify both the supported and the static capabilities, when masked
with any of the CAN_CTRLMODE_* bit flags:
supported & flags & Controller capabilities
CAN_CTRLMODE_* CAN_CTRLMODE_*
-----------------------------------------------------------------------
false false Feature not supported (always disabled)
false true Static feature (always enabled)
true false Feature supported but disabled
true true Feature supported and enabled
Link: https://lore.kernel.org/all/20211213160226.56219-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Previous patch removed can_priv::ctrlmode_static to replace it with
can_get_static_ctrlmode().
A condition sine qua non for this to work is that the controller
static modes should never be set in can_priv::ctrlmode_supported
(c.f. the comment on can_priv::ctrlmode_supported which states that it
is for "options that can be *modified* by netlink"). Also, this
condition is already correctly fulfilled by all existing drivers
which rely on the ctrlmode_static feature.
Nonetheless, we added an extra safeguard in can_set_static_ctrlmode()
to return an error value and to warn the developer who would be
adventurous enough to set to static a given feature that is already
set to supported.
The drivers which rely on the static controller mode are then updated
to check the return value of can_set_static_ctrlmode().
Link: https://lore.kernel.org/all/20211213160226.56219-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The statically enabled features of a CAN controller can be retrieved
using below formula:
| u32 ctrlmode_static = priv->ctrlmode & ~priv->ctrlmode_supported;
As such, there is no need to store this information. This patch remove
the field ctrlmode_static of struct can_priv and provides, in
replacement, the inline function can_get_static_ctrlmode() which
returns the same value.
Link: https://lore.kernel.org/all/20211213160226.56219-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.
The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.
This patch fixes all the CAN drivers.
Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).
[1] commit ed3320cec279 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")
Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The field dev_port of struct net_device indicates the port number of a
network device [1]. This patch populates this field.
This field can be helpful to distinguish between the two network
interfaces of a dual channel device (i.e. ES581.4 or ES582.1). Indeed,
at the moment, all the network interfaces of a same device share the
same static udev attributes c.f. output of:
| udevadm info --attribute-walk /sys/class/net/canX
The dev_port attribute can then be used to write some udev rules to,
for example, assign a permanent name to each network interface based
on the serial/dev_port pair (which is convenient when you have a test
bench with several CAN devices connected simultaneously and wish to
keep consistent interface names upon reboot).
[1] https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net
Link: https://lore.kernel.org/all/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Suggested-by: Lukas Magel <lukas.magel@escrypt.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It is preferred that drivers use platform_get_irq() instead of
irq_of_parse_and_map(), so replace.
Link: https://lore.kernel.org/all/20211221200016.13459-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the MEGA define plus the comment /* Hz */ when assigning
frequencies.
Link: https://lore.kernel.org/all/20211210075803.343841-1-mkl@pengutronix.de
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the unused memberecho_skb from the struct
usb_8dev_priv.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220104230753.956520-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Depending on BIOS configuration IOSM driver exchanges
protocol required for putting device into D3L2 or D3L1.2.
ipc_pcie_suspend_s2idle() is implemented to put device to D3L1.2.
This patch forces PCI core know this device should stay at D0.
- pci_save_state()is expensive since it does a lot of slow PCI
config reads.
The reported issue is not observed on x86 platform. The supurios
wake on AMD platform needs to be futher debugged with orignal patch
submitter [1]. Also the impact of adding pci_save_state() needs to be
assessed by testing it on other platforms.
This reverts commit f4dd5174e273("net: wwan: iosm: Keep device
at D0 for s2idle case").
[1] https://lore.kernel.org/all/20211224081914.345292-2-kai.heng.feng@canonical.com/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20220104150213.1894-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return value from efx_mcdi_rpc() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes: e63a02348958 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/7c03768d-d948-c935-a7ab-b1f963ac7eed@linux.vnet.ibm.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for scatter gather DMA. DMA in PMAC splits
the packet into several buffers when the MTU on the CPU port is
less than the MTU of the switch. The first buffer starts at an
offset of NET_IP_ALIGN. In subsequent buffers, dma ignores the
offset. Thanks to this patch, the user can still connect to the
device in such a situation. For normal configurations, the patch
has no effect on performance.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for external timestamp and periodic signal output.
TJA1103 have one periodic signal and one external time stamp signal that
can be multiplexed on all 11 gpio pins.
The periodic signal can be only enabled or disabled. Have no start time
and if is enabled will be generated with a period of one second in sync
with the LTC seconds counter. The phase change is possible only with a
half of a second.
The external timestamp signal has no interrupt and no valid bit and
that's why the timestamps are handled by polling in .do_aux_work.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get originating device from tuple offload metadata match ingress_ifindex,
and set flow_source hint to either LOCAL for vf/sf reps, UPLINK for
uplink/wire/tunnel devices/bond, or ANY (as before this patch)
for all others.
This allows lower layer (software steering or firmware) to insert the tuple
rule only in one table (either rx or tx) instead of two (rx and tx).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'high_dma' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including a now
useless parameter to vxge_device_register().
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'dma_flag' can only be 'true' after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including the now
useless 'high_dma_flag' field in 'struct s2io_nic'.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sorry for being rude but new vendors/drivers are supposed to be disabled
by default, otherwise we will have to manually keep track of all vendors
we are not interested in building.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
CC: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pcs-lynx.c used lynx_pcs and lynx as a variable name within the same file.
This standardizes all internal variables to just "lynx"
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
