| Age | Commit message (Collapse) | Author |
|---|
|
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077a3 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the firmware API is partial and allows to offload only
the dscp part of the tos, also, ipv6 support isn't there yet.
As such, remove the offloading option of ipv4 dscp till the FW
APIs are more comprehensive.
Fixes: d79b6df6b10a ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.
To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.
Fixes: 7768d1971de6 ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Mohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e49901 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2c8 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull networking fixes from David Miller:
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug on sparc where we may dereference freed stack memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Work around deallocated stack frame reference gcc bug on sparc.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert an ACPICA commit from the 4.11 cycle that causes problems
to happen on some systems and add a protection against possible kernel
crashes due to table reference counter imbalance.
Specifics:
- Revert a 4.11 ACPICA change that made assumptions which are not
satisfied on some systems and caused the enumeration of resources
to fail on them (Rafael Wysocki).
- Add a mechanism to prevent tables from being unmapped prematurely
due to reference counter overflows (Lv Zheng)"
* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Revert "ACPICA: Disassembler: Enhance resource descriptor detection"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These revert a recent cpufreq schedutil governor change that turned
out to be problematic and fix a few minor issues in cpufreq, cpuidle
and the Exynos devfreq drivers.
Specifics:
- Revert a recent cpufreq schedutil governor change that caused some
systems to behave undesirably (Rafael Wysocki).
- Fix a cpufreq conservative governor issue introduced during the
3.10 cycle that prevents it from working as expected in some
situations (Tomasz Wilczyński).
- Fix an error code path in the generic cpuidle driver for DT-based
systems (Christophe Jaillet).
- Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
Krzysztof Kozlowski)"
* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: dt: Add missing 'of_node_put()'
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
- ifdef-based bandaid for a long-standing issue with HID driver
matching, avoiding regressions in cases where specific driver is not
enabled in kernel .config, from Jiri Kosina
* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: let generic driver yield control iff specific driver has been enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build dependency issues at CEC core with randconfigs
- fix an off by one error at vb2
- a race fix at cec core
- driver fixes at tc358743, sir_ir and rainshadow-cec
* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
[media] cec: race fix: don't return -ENONET in cec_receive()
[media] sir_ir: infinite loop in interrupt handler
[media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
[media] cec: improve MEDIA_CEC_RC dependencies
[media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
[media] rainshadow-cec: Fix missing spin_lock_init()
[media] tc358743: fix register i2c_rd/wr function fix
|
|
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* acpica-fixes:
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Revert "ACPICA: Disassembler: Enhance resource descriptor detection"
|
|
* pm-cpufreq:
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
* pm-cpuidle:
cpuidle: dt: Add missing 'of_node_put()'
* pm-devfreq:
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
|
|
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db444629 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 90eff9096c01 ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:
drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's already added by pr_fmt so remove the explicit use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Getting the device version out of the driver really aids debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are many situations where generic HID driver provides some basic level
of support for certain device, but later this support (usually by implementing
vendor-specific extensions of HID protocol) is extended and the support moved
over to a separate (usually per-vendor) specific driver.
This might bring a rather unpleasant suprise for users, as all of a sudden
there is a new config option they have to enable in order to get any support
for their device whatsoever, although previous kernel versions provided basic
support through the generic driver. Which is rightfully seen as a regression.
Fix this by including the entry for a particular device in
hid_have_special_driver[] iff the specific config option has been specified,
and let generic driver handle the device otherwise.
Also make the behavior of hid_scan_report() (where the same decision is being
taken on a per-report level) consistent.
While at it, reshuffle the hid_have_special_driver[] a bit to restore the
alphabetical ordering (first order by config option, and within those
sections order by VID).
This is considered a short-term solution, before generic way of giving
precedence to special drivers and falling back to generic driver is
figured out.
While at it, fixup a missing entry for GFRM driver; thanks to Hans de Geode for
spotting this (and for discovering a few issues in the conversion).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull Xtensa fixes from Max Filippov:
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: don't use linux IRQ #0
xtensa: reduce double exception literal reservation
xtensa: ISS: Use kmalloc_array() in simdisk_init()
xtensa: Use seq_puts() in c_show()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A fix for KVM to avoid kernel oopses in case of host protection
faults due to runtime instrumentation
- A fix for the AP bus to avoid dead devices after unbind / bind
- A fix for a compile warning merged from the vfio_ccw tree
- Updated default configurations
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfig
s390/zcrypt: Fix blocking queue device after unbind/bind.
s390/vfio_ccw: make some symbols static
s390/kvm: do not rely on the ILC on kvm host protection fauls
|
|
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a36 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'of_node_put()' should be called on pointer returned by
'of_parse_phandle()' when done. In this function this is done in all path
except this 'continue', so add it.
Fixes: 97735da074fd (drivers: cpuidle: Add status property to ARM idle states)
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency decrease checking)
Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Considering this case:
1. A program opens a sysfs table file 65535 times, it can increase
validation_count and first increment cause the table to be mapped:
validation_count = 65535
2. AML execution causes "Load" to be executed on the same
table, this time it cannot increase validation_count, so
validation_count remains:
validation_count = 65535
3. The program closes sysfs table file 65535 times, it can decrease
validation_count and the last decrement cause the table to be
unmapped:
validation_count = 0
4. AML code still accessing the loaded table, kernel crash can be
observed.
To prevent that from happening, add a validation_count threashold.
When it is reached, the validation_count can no longer be
incremented/decremented to invalidate the table descriptor (means
preventing table unmappings)
Note that code added in acpi_tb_put_table() is actually a no-op but
changes the warning message into a "warn once" one. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ppmu_events array is accessed only in this compilation unit so it
can be made static.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox mlx5 fixes 2017-06-11
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Added BW check for DIM decision mechanism") kernels >= 4.9
("net/mlx5e: Fix wrong indications in DIM due to counter wraparound") kernels >= 4.9
("net/mlx5: Remove several module events out of ethtool stats") kernels >= 4.10
("net/mlx5: Enable 4K UAR only when page size is bigger than 4K") kernels >= 4.11
*all patches apply with no issue on their -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch also change the mapping functions to devm_ functions
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixing a bug that the driver does not unmask the IO interrupts
in ndo_open():
occasionally, the MSI-X interrupt (for one or more IO queues)
can be masked when ndo_close() was called.
If that is followed by ndo open(),
then the MSI-X will be still masked so no interrupt
will be received by the driver.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current flow to detect admin completion is:
while (command_not_completed) {
if (timeout)
error
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness fixes from Ted Ts'o:
"Improve performance by using a lockless update mechanism suggested by
Linus, and make sure we refresh per-CPU entropy returned get_random_*
as soon as the CRNG is initialized"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: invalidate batched entropy after crng init
random: use lockless method of accessing and updating f->reg_idx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A few overdue GPIO patches for the v4.12 kernel.
- Fix debounce logic on the Aspeed platform.
- Fix the "virtual gpio" things on the Intel Crystal Cove.
- Fix the blink counter selection on the MVEBU platform"
* tag 'gpio-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: fix gpio bank registration when pwm is used
gpio: mvebu: fix blink counter register selection
MAINTAINERS: remove self from GPIO maintainers
gpio: crystalcove: Do not write regular gpio registers for virtual GPIOs
gpio: aspeed: Don't attempt to debounce if disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 4.12-rc5. Nothing major here,
just some small bugfixes found by people testing, and a MAINTAINERS
file update for the genwqe driver.
All have been in linux-next with no reported issues"
[ The cxl driver fix came in through the powerpc tree earlier ]
* tag 'char-misc-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
cxl: Avoid double free_irq() for psl,slice interrupts
mei: make sysfs modalias format similar as uevent modalias
drivers: char: mem: Fix wraparound check to allow mappings up to the end
MAINTAINERS: Change maintainer of genwqe driver
goldfish_pipe: use GFP_ATOMIC under spin lock
firmware: vpd: do not leak kobjects
firmware: vpd: avoid potential use-after-free when destroying section
firmware: vpd: do not leave freed section attributes to the list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"These are mostly all IIO driver fixes, resolving a number of tiny
issues. There's also a ccree and lustre fix in here as well, both fix
problems found in those codebases.
All have been in linux-next with no reported issues"
* tag 'staging-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ccree: fix buffer copy
staging/lustre/lov: remove set_fs() call from lov_getstripe()
staging: ccree: add CRYPTO dependency
iio: adc: sun4i-gpadc-iio: fix parent device being used in devm function
iio: light: ltr501 Fix interchanged als/ps register field
iio: adc: bcm_iproc_adc: swap primary and secondary isr handler's
iio: trigger: fix NULL pointer dereference in iio_trigger_write_current()
iio: adc: max9611: Fix attribute measure unit
iio: adc: ti_am335x_adc: allocating too much in probe
iio: adc: sun4i-gpadc-iio: Fix module autoload when OF devices are registered
iio: adc: sun4i-gpadc-iio: Fix module autoload when PLATFORM devices are registered
iio: proximity: as3935: fix iio_trigger_poll issue
iio: proximity: as3935: fix AS3935_INT mask
iio: adc: Max9611: checking for ERR_PTR instead of NULL in probe
iio: proximity: as3935: recalibrate RCO after resume
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.12-rc5
They are for some reported issues in the chipidea and gadget drivers.
Nothing major. All have been in linux-next for a while with no
reported issues"
* tag 'usb-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc: renesas_usb3: Fix PN_INT_ENA disabling timing
usb: gadget: udc: renesas_usb3: lock for PN_ registers access
usb: gadget: udc: renesas_usb3: fix deadlock by spinlock
usb: gadget: udc: renesas_usb3: fix pm_runtime functions calling
usb: gadget: f_mass_storage: Serialize wake and sleep execution
usb: dwc2: add support for the DWC2 controller on Meson8 SoCs
phy: qualcomm: phy-qcom-qmp: fix application of sizeof to pointer
usb: musb: dsps: keep VBUS on for host-only mode
usb: chipidea: core: check before accessing ci_role in ci_role_show
usb: chipidea: debug: check before accessing ci_role
phy: qcom-qmp: fix return value check in qcom_qmp_phy_create()
usb: chipidea: udc: fix NULL pointer dereference if udc_start failed
usb: chipidea: imx: Do not access CLKONOFF on i.MX51
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of user visible fixes (excepting one format string
change).
Four of the qla2xxx fixes only affect the firmware dump path, but it's
still important to the enterprise. The rest are various NULL pointer
crash conditions or outright driver hangs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: libcxgbi: in error case RST tcp conn
scsi: scsi_debug: Avoid PI being disabled when TPGS is enabled
scsi: qla2xxx: Fix extraneous ref on sp's after adapter break
scsi: lpfc: prevent potential null pointer dereference
scsi: lpfc: Avoid NULL pointer dereference in lpfc_els_abort()
scsi: lpfc: nvmet_fc: fix format string
scsi: qla2xxx: Fix crash due to NULL pointer dereference of ctx
scsi: qla2xxx: Fix mailbox pointer error in fwdump capture
scsi: qla2xxx: Set bit 15 for DIAG_ECHO_TEST MBC
scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues
scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue
scsi: qla2xxx: Fix NULL pointer access due to redundant fc_host_port_name call
scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive
scsi: bnx2fc: fix race condition in bnx2fc_get_host_stats()
scsi: qla2xxx: don't disable a not previously enabled PCI device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"We expanded the device-dax fs type in 4.12 to be a generic provider of
a struct dax_device with an embedded inode. However, Sasha found some
basic negative testing was not run to verify that this fs cleanly
handles being mounted directly.
Note that the fresh rebase was done to remove an unnecessary Cc:
<stable> tag, but this commit otherwise had a build success
notification from the 0day robot."
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix 'dax' device filesystem inode destruction crash
|
|
When the page size isn't bigger than 4K, there is no added value of enabling 4K
UAR feature in the Firmware.
Modified the condition of enabling the 4K UAR accordingly.
Fixes: f502d834950a ("net/mlx5: Activate support for 4K UARs")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
