| Age | Commit message (Collapse) | Author |
|---|
|
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
|
|
The previous commit didn't fix the bug properly. By mistake, it replaces
the pointer of the next skb in the descriptor ring instead of the current
one. As a result, the two descriptors are assigned the same SKB. The error
is seen during the iperf test when skb_put tries to insert a second packet
and exceeds the available buffer.
Fixes: c7718ee96dbc ("net: lantiq: fix memory corruption in RX ring ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the QMI_WWAN_FLAG_PASS_THROUGH is set, netif_rx() is called from
qmi_wwan_rx_fixup(). When the call to netif_rx() is successful (which is
most of the time), usbnet_skb_return() is called (from rx_process()).
usbnet_skb_return() will then call netif_rx() a second time for the same
skb.
Simplify the code and avoid the redundant netif_rx() call by changing
qmi_wwan_rx_fixup() to always return 1 when QMI_WWAN_FLAG_PASS_THROUGH
is set. We then leave it up to the existing infrastructure to call
netif_rx().
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 4d06dd537f95 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511cd ("ptp: validate the requested frequency adjustment.")
Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.
[ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002
....
[ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 2925.037005] pc : inode_permission+0x2c/0x198
[ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8
[ 2925.045903] sp : ffff80001276ba70
[ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000
[ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100
[ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001
[ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000
[ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004
[ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030
[ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420
[ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080
[ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065
[ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188
[ 2925.120671] Call trace:
[ 2925.123119] inode_permission+0x2c/0x198
[ 2925.127042] lookup_one_len_common+0xb0/0xf8
[ 2925.131315] lookup_one_len_unlocked+0x34/0xb0
[ 2925.135764] lookup_positive_unlocked+0x14/0x50
[ 2925.140296] debugfs_lookup+0x68/0xa0
[ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0
[ 2925.148675] dwc3_gadget_exit+0x28/0x78
[ 2925.152518] dwc3_drd_exit+0x100/0x1f8
[ 2925.156267] dwc3_remove+0x11c/0x120
[ 2925.159851] dwc3_shutdown+0x14/0x20
[ 2925.163432] platform_shutdown+0x28/0x38
[ 2925.167360] device_shutdown+0x15c/0x378
[ 2925.171291] kernel_restart_prepare+0x3c/0x48
[ 2925.175650] kernel_restart+0x1c/0x68
[ 2925.179316] __do_sys_reboot+0x218/0x240
[ 2925.183247] __arm64_sys_reboot+0x28/0x30
[ 2925.187262] invoke_syscall+0x48/0x100
[ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8
[ 2925.195726] do_el0_svc+0x28/0x88
[ 2925.199045] el0_svc+0x20/0x30
[ 2925.202104] el0_sync_handler+0xa8/0xb0
[ 2925.205942] el0_sync+0x148/0x180
[ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660)
[ 2925.215372] ---[ end trace 124254d8e485a58b ]---
[ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 2925.227676] Kernel Offset: disabled
[ 2925.231164] CPU features: 0x00001001,20000846
[ 2925.235521] Memory Limit: none
[ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20210608105656.10795-1-peter.chen@kernel.org
(cherry picked from commit 2a042767814bd0edf2619f06fecd374e266ea068)
Link: https://lore.kernel.org/r/20210615080847.GA10432@jackp-linux.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the function prototype of mhi_ndo_xmit to match
ndo_start_xmit. This otherwise leads to run time failures when
CFI is enabled in kernel.
Fixes: 3ffec6a14f24 ("net: Add mhi-net driver")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzbot reported memory leak in tty_init_dev().
The problem was in unputted tty in ldisc_open()
static int ldisc_open(struct tty_struct *tty)
{
...
ser->tty = tty_kref_get(tty);
...
result = register_netdevice(dev);
if (result) {
rtnl_unlock();
free_netdev(dev);
return -ENODEV;
}
...
}
Ser pointer is netdev private_data, so after free_netdev()
this pointer goes away with unputted tty reference. So, fix
it by adding tty_kref_put() before freeing netdev.
Reported-and-tested-by: syzbot+f303e045423e617d2cad@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TID returned during successful filter creation is relative to
the region in which the filter is created. Using it directly always
returns Hi Prio/Normal filter region's entry for the first couple of
entries, even though the rule is actually inserted in Hash region.
Fix by analyzing in which region the filter has been inserted and
save the absolute TID to be used for lookup later.
Fixes: db43b30cd89c ("cxgb4: add ethtool n-tuple filter deletion")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: e87ad5539343 ("netxen: support pci error handlers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 451724c821c1 ("qlcnic: aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The purpose of the loop using u64_stats_fetch_*_irq() is to ensure
statistics on a given CPU are collected atomically. If one of the
statistics values gets updated within the begin/retry window, the
loop will run again.
Currently the statistics totals are updated inside that window.
This means that if the loop ever retries, the statistics for the
CPU will be counted more than once.
Fix this by taking a snapshot of a CPU's statistics inside the
protected window, and then updating the counters with the snapshot
values after exiting the loop.
(Also add a newline at the end of this file...)
Fixes: 192c4b5d48f2a ("net: qualcomm: rmnet: Add support for 64 bit stats")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 4c38f2df71c8e33c0b64865992d693f5022eeaad.
There are few races in the frequency invariance support for CPPC driver,
namely the driver doesn't stop the kthread_work and irq_work on policy
exit during suspend/resume or CPU hotplug.
A proper fix won't be possible for the 5.13-rc, as it requires a lot of
changes. Lets revert the patch instead for now.
Fixes: 4c38f2df71c8 ("cpufreq: CPPC: Add support for frequency invariance")
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four reasonably small fixes to the core for scsi host allocation
failure paths.
The root problem is that we're not freeing the memory allocated by
dev_set_name(), which involves a rejig of may of the free on error
paths to do put_device() instead of kfree which, in turn, has several
other knock on ramifications and inspection turned up a few other
lurking bugs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Only put parent device if host state differs from SHOST_CREATED
scsi: core: Put .shost_dev in failure path if host state changes to RUNNING
scsi: core: Fix failure handling of scsi_add_host_with_dma()
scsi: core: Fix error handling of scsi_host_alloc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes for 5.13-rc6.
There are more than I would normally like, but there's been a bunch of
people banging on the gadget and dwc3 and typec code recently for I
think an Android release, which has resulted in a number of small
fixes. It's nice to see companies send fixes upstream for this type of
work, a notable change from years ago.
Anyway, fixes in here are:
- usb-serial device id updates
- usb-serial cp210x driver fixes for broken firmware versions
- typec fixes for crazy charging devices and other reported problems
- dwc3 fixes for reported problems found
- gadget fixes for reported problems
- tiny xhci fixes
- other small fixes for reported issues.
- revert of a problem fix found by linux-next testing
All of these have passed 0-day and linux-next testing with no reported
problems (the revert for the found linux-next build problem included)"
* tag 'usb-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (44 commits)
Revert "usb: gadget: fsl: Re-enable driver for ARM SoCs"
usb: typec: mux: Fix copy-paste mistake in typec_mux_match
usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path
usb: gadget: fsl: Re-enable driver for ARM SoCs
usb: typec: wcove: Use LE to CPU conversion when accessing msg->header
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
usb: misc: brcmstb-usb-pinmap: check return value after calling platform_get_resource()
usb: dwc3: ep0: fix NULL pointer exception
usb: gadget: eem: fix wrong eem header operation
usb: typec: intel_pmc_mux: Put ACPI device using acpi_dev_put()
usb: typec: intel_pmc_mux: Add missed error check for devm_ioremap_resource()
usb: typec: intel_pmc_mux: Put fwnode in error case during ->probe()
usb: typec: tcpm: Do not finish VDM AMS for retrying Responses
usb: fix various gadget panics on 10gbps cabling
usb: fix various gadgets null ptr deref on 10gbps cabling.
usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir
usb: f_ncm: only first packet of aggregate needs to start timer
USB: f_ncm: ncm_bitrate (speed) is unsigned
MAINTAINERS: usb: add entry for isp1760
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"A single 8250_exar serial driver fix for a reported problem with a
change that happened in 5.13-rc1.
It has been in linux-next with no reported problems"
* tag 'tty-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_exar: Avoid NULL pointer dereference at ->exit()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Two tiny staging driver fixes:
- ralink-gdma driver authorship information fixed up
- rtl8723bs driver fix for reported regression
Both have been in linux-next for a while with no reported problems"
* tag 'staging-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ralink-gdma: Remove incorrect author information
staging: rtl8723bs: Fix uninitialized variables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small misc driver fixes for 5.13-rc6 that fix some
reported problems:
- Tiny phy driver fixes for reported issues
- rtsx regression for when the device suspended
- mhi driver fix for a use-after-free
All of these have been in linux-next for a few days with no reported
issues"
* tag 'char-misc-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: rtsx: separate aspm mode into MODE_REG and MODE_CFG
bus: mhi: pci-generic: Fix hibernation
bus: mhi: pci_generic: Fix possible use-after-free in mhi_pci_remove()
bus: mhi: pci_generic: T99W175: update channel name from AT to DUN
phy: Sparx5 Eth SerDes: check return value after calling platform_get_resource()
phy: ralink: phy-mt7621-pci: drop 'of_match_ptr' to fix -Wunused-const-variable
phy: ti: Fix an error code in wiz_probe()
phy: phy-mtk-tphy: Fix some resource leaks in mtk_phy_init()
phy: cadence: Sierra: Fix error return code in cdns_sierra_phy_probe()
phy: usb: Fix misuse of IS_ENABLED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix some documentation warnings for Allwinner
- Fix duplicated GPIO groups on Qualcomm SDX55
- Fix a double enablement bug in the Ralink driver
- Fix the Qualcomm SC8180x Kconfig so the driver can be selected.
* tag 'pinctrl-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Make it possible to select SC8180x TLMM
pinctrl: ralink: rt2880: avoid to error in calls is pin is already enabled
pinctrl: qcom: Fix duplication in gpio_groups
pinctrl: aspeed: Fix minor documentation error
|
|
Pull block fixes from Jens Axboe:
"A few fixes that should go into 5.13:
- Fix a regression deadlock introduced in this release between open
and remove of a bdev (Christoph)
- Fix an async_xor md regression in this release (Xiao)
- Fix bcache oversized read issue (Coly)"
* tag 'block-5.13-2021-06-12' of git://git.kernel.dk/linux-block:
block: loop: fix deadlock between open and remove
async_xor: check src_offs is not NULL before updating it
bcache: avoid oversized read request in cache missing code path
bcache: remove bcache device self-defined readahead
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"Fix a shift-out-of-bounds error in gpio-wcd934x"
* tag 'gpio-fixes-for-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: wcd934x: Fix shift-out-of-bounds error
|
|
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Another week of fixes, nothing too crazy, but a few all over the
place.
Two locking fixes in the core/ttm area, a couple of small driver fixes
(radeon, sun4i, mcde, vc4). Then msm and amdgpu have a set of fixes
each, mostly for smaller things, though the msm has a DSI fix for a
black screen.
I haven't seen any intel fixes this week so they may have a few that
may or may not wait for next week.
drm:
- auth locking fix
ttm:
- locking fix
amdgpu:
- Use kvzmalloc in amdgu_bo_create
- Use drm_dbg_kms for reporting failure to get a GEM FB
- Fix some register offsets for Sienna Cichlid
- Fix fall-through warning
radeon:
- memcpy_to/from_io fixes
msm:
- NULL ptr deref fix
- CP_PROTECT reg programming fix
- incorrect register shift fix
- DSI blank screen fix
sun4i:
- hdmi output probing fix
mcde:
- DSI pipeline calc fix
vc4:
- out of bounds fix"
* tag 'drm-fixes-2021-06-11' of git://anongit.freedesktop.org/drm/drm:
drm/msm/dsi: Stash away calculated vco frequency on recalc
drm: Lock pointer access in drm_master_release()
drm/mcde: Fix off by 10^3 in calculation
drm/msm/a6xx: avoid shadow NULL reference in failure path
drm/msm/a6xx: fix incorrectly set uavflagprd_inv field for A650
drm/msm/a6xx: update/fix CP_PROTECT initialization
radeon: use memcpy_to/fromio for UVD fw upload
drm/amd/pm: Fix fall-through warning for Clang
drm/amdgpu: Fix incorrect register offsets for Sienna Cichlid
drm/amdgpu: Use drm_dbg_kms for reporting failure to get a GEM FB
drm/amdgpu: switch kzalloc to kvzalloc in amdgpu_bo_create
drm/msm: Init mm_list before accessing it for use_vram path
drm: Fix use-after-free read in drm_getunique()
drm/vc4: fix vc4_atomic_commit_tail() logic
drm/ttm: fix deref of bo->ttm without holding the lock v2
drm/sun4i: dw-hdmi: Make HDMI PHY into a platform device
|
|
When using firmware-assisted PHY firmware image write to flash,
halt the chip before beginning the flash write operation to allow
the running firmware to store the image persistently. Otherwise,
the running firmware will only store the PHY image in local on-chip
RAM, which will be lost after next reset.
Fixes: 4ee339e1e92a ("cxgb4: add support to flash PHY image")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before writing new PHY firmware to on-chip memory, driver queries
firmware for current running PHY firmware version, which can result
in sleep waiting for reply. So, move spinlock closer to the actual
on-chip memory write operation, instead of taking it at the callers.
Fixes: 5fff701c838e ("cxgb4: always sync access when flashing PHY firmware")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Boot images are copied to memory and updated with current underlying
device ID before flashing them to adapter. Ensure the updated images
are always flashed in Big Endian to allow the firmware to read the
new images during boot properly.
Fixes: 550883558f17 ("cxgb4: add support to flash boot image")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: ab69bde6b2e9 ("alx: add a simple AR816x/AR817x device driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a problematic recent commit and fix a regression
introduced during the 5.12 development cycle.
Specifics:
- Revert recent commit that attempted to fix the FACS table reference
counting but introduced a problem with accessing the hardware
signature after hibernation (Zhang Rui).
- Fix regression in the _OSC handling that broke the loading of ACPI
tables on some systems (Mika Westerberg)"
* tag 'acpi-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Pass the same capabilities to the _OSC regardless of the query flag
Revert "ACPI: sleep: Put the FACS table after using it"
|
|
Commit c76f48eb5c08 ("block: take bd_mutex around delete_partitions in
del_gendisk") adds disk->part0->bd_mutex in del_gendisk(), this way
causes the following AB/BA deadlock between removing loop and opening
loop:
1) loop_control_ioctl(LOOP_CTL_REMOVE)
-> mutex_lock(&loop_ctl_mutex)
-> del_gendisk
-> mutex_lock(&disk->part0->bd_mutex)
2) blkdev_get_by_dev
-> mutex_lock(&disk->part0->bd_mutex)
-> lo_open
-> mutex_lock(&loop_ctl_mutex)
Add a new Lo_deleting state to remove the need for clearing
->private_data and thus holding loop_ctl_mutex in the ioctl
LOOP_CTL_REMOVE path.
Based on an analysis and earlier patch from
Ming Lei <ming.lei@redhat.com>.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: c76f48eb5c08 ("block: take bd_mutex around delete_partitions in del_gendisk")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210605140950.5800-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Current logic is performing hard reset and causing the programmed
registers to be wiped out.
as per datasheet: https://www.ti.com/lit/ds/symlink/dp83867cr.pdf
8.6.26 Control Register (CTRL)
do SW_RESTART to perform a reset not including the registers,
If performed when link is already present,
it will drop the link and trigger re-auto negotiation.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Geet Modi <geet.modi@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fixes for tps23861, scpi-hwmon, and corsair-psu drivers, plus a
bindings fix for TI ADS7828"
* tag 'hwmon-for-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (tps23861) correct shunt LSB values
hwmon: (tps23861) set current shunt value
hwmon: (tps23861) define regmap max register
hwmon: (scpi-hwmon) shows the negative temperature properly
hwmon: (corsair-psu) fix suspend behavior
dt-bindings: hwmon: Fix typo in TI ADS7828 bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes to the Renesas SDHI driver:
- Fix HS400 on R-Car M3-W+
- Abort tuning when timeout detected"
* tag 'mmc-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: Fix HS400 on R-Car M3-W+
mmc: renesas_sdhi: abort tuning when timeout detected
|
|
* acpi-bus:
ACPI: Pass the same capabilities to the _OSC regardless of the query flag
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.13-rc6
Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.
Both have been in linux-next over night and with no reported issues.
* tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
|
|
This reverts commit e0e8b6abe8c862229ba00cdd806e8598cdef00bb.
Turns out this breaks the build. We had numerous reports of problems
from linux-next and 0-day about this not working properly, so revert it
for now until it can be figured out properly.
The build errors are:
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize'
arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release'
fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init'
fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e0e8b6abe8c8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Leo Li <leoyang.li@nxp.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.13-2021-06-09:
amdgpu:
- Use kvzmalloc in amdgu_bo_create
- Use drm_dbg_kms for reporting failure to get a GEM FB
- Fix some register offsets for Sienna Cichlid
- Fix fall-through warning
radeon:
- memcpy_to/from_io fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610035631.3943-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One fix for snu4i that prevents it from probing, two locking fixes for
ttm and drm_auth, one off-by-x1000 fix for mcde and a fix for vc4 to
prevent an out-of-bounds access.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610171653.lqsoadxrhdk73cdy@gilmour
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
- NULL ptr deref fix
- CP_PROTECT reg programming fix
- incorrect register shift fix
- DSI blank screen fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvbcz0=QxGYnX9u7cD1SCvFSx20dzrZuOccjtRRBTJd5Q@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2021-06-09
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful. Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.
Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.
FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad8600 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.
This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:
arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y
To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the
ARM platforms, and with COMPILE_TEST.
Fixes: a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210610034957.93376-1-joel@jms.id.au
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As LKP noticed the Sparse is not happy about strict type handling:
.../typec/tcpm/wcove.c:380:50: sparse: expected unsigned short [usertype] header
.../typec/tcpm/wcove.c:380:50: sparse: got restricted __le16 const [usertype] header
Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
"A mixture of small bug fixes and a small security issue:
- WARN_ON when IPoIB is automatically moved between namespaces
- Long standing bug where mlx5 would use the wrong page for the
doorbell recovery memory if fork is used
- Security fix for mlx4 that disables the timestamp feature
- Several crashers for mlx5
- Plug a recent mlx5 memory leak for the sig_mr"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix initializing CQ fragments buffer
RDMA/mlx5: Delete right entry from MR signature database
RDMA: Verify port when creating flow rule
RDMA/mlx5: Block FDB rules when not in switchdev mode
RDMA/mlx4: Do not map the core_clock page to user space unless enabled
RDMA/mlx5: Use different doorbell memory for different processes
RDMA/ipoib: Fix warning caused by destroying non-initial netns
|
|
Current shunt LSB values got reversed during in the
original driver commit.
So, correct the current shunt LSB values according to
the datasheet.
This caused reading slightly skewed current values.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-3-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TPS23861 has a configuration bit for setting of the
current shunt value used on the board.
Its bit 0 of the General Mask 1 register.
According to the datasheet bit values are:
0 for 255 mOhm (Default)
1 for 250 mOhm
So, configure the bit before registering the hwmon
device according to the value passed in the DTS or
default one if none is passed.
This caused potentially reading slightly skewed values
due to max current value being 1.02A when 250mOhm shunt
is used instead of 1.0A when 255mOhm is used.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Define the max register address the device supports.
This allows reading the whole register space via
regmap debugfs, without it only register 0x0 is visible.
This was forgotten in the original driver commit.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-1-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c96a ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc33875 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc33875 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The function init_cq_frag_buf() can be called to initialize the current CQ
fragments buffer cq->buf, or the temporary cq->resize_buf that is filled
during CQ resize operation.
However, the offending commit started to use function get_cqe() for
getting the CQEs, the issue with this change is that get_cqe() always
returns CQEs from cq->buf, which leads us to initialize the wrong buffer,
and in case of enlarging the CQ we try to access elements beyond the size
of the current cq->buf and eventually hit a kernel panic.
[exception RIP: init_cq_frag_buf+103]
[ffff9f799ddcbcd8] mlx5_ib_resize_cq at ffffffffc0835d60 [mlx5_ib]
[ffff9f799ddcbdb0] ib_resize_cq at ffffffffc05270df [ib_core]
[ffff9f799ddcbdc0] llt_rdma_setup_qp at ffffffffc0a6a712 [llt]
[ffff9f799ddcbe10] llt_rdma_cc_event_action at ffffffffc0a6b411 [llt]
[ffff9f799ddcbe98] llt_rdma_client_conn_thread at ffffffffc0a6bb75 [llt]
[ffff9f799ddcbec8] kthread at ffffffffa66c5da1
[ffff9f799ddcbf50] ret_from_fork_nospec_begin at ffffffffa6d95ddd
Fix it by getting the needed CQE by calling mlx5_frag_buf_get_wqe() that
takes the correct source buffer as a parameter.
Fixes: 388ca8be0037 ("IB/mlx5: Implement fragmented completion queue (CQ)")
Link: https://lore.kernel.org/r/90a0e8c924093cfa50a482880ad7e7edb73dc19a.1623309971.git.leonro@nvidia.com
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
