| Age | Commit message (Collapse) | Author |
|---|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report taprio offload status. This includes per txq and global
counters of window_drops and tx_overruns.
Window_drops count include count of frames dropped because of
queueMaxSDU setting and HLBF error. Transmission overrun counter
inform the user application whether any packets are currently being
transmitted on a particular queue during a gate-close event.DWMAC IPs
takes care Transmission overrun won't happen hence this is always 0.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep per Tx-queue error count on Head-Of-Line Blocking due to frame
size(HLBF) error. The MAC raises HLBF error on one or more queues
when none of the time Intervals of open-gates in the GCL is greater
than or equal to the duration needed for frame transmission and by
default drops those packets that causes HLBF error. EST_FRM_SZ_ERR
register provides the One Hot encoded Queue numbers that have the
Frame Size related error.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring queueMaxSDU. As DWMAC IPs doesn't support
queueMaxSDU table handle this in the SW. The maximum 802.3 frame size
that is allowed to be transmitted by any queue is queueMaxSDU +
16 bytes (i.e. 6 bytes SA + 6 bytes DA + 4 bytes FCS).
Inspired from intel i225 driver.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a missing quirk to enable support for the StarFive JH7100 SoC.
Additionally, for greater flexibility in operation, allow using the
rgmii-rxid and rgmii-txid phy modes.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Class-based I2C probing requires detect() and address_list to be
set in the I2C client driver, see checks in i2c_detect().
It's misleading to declare I2C_CLASS_HWMON support if this
precondition isn't met.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/77b5ab8e-20f2-4310-bd89-57db99e2f53b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlxsw driver uses 'unsigned int' for reference counters in several
structures. Instead, use refcount_t type which allows us to catch overflow
and underflow issues. Change the type of the counters and use the
appropriate API.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
mlxsw_sp stores an array of LAGs. When a port joins a LAG, in case that
this LAG is already in use, we only have to increase the reference counter.
Otherwise, we have to search for an unused LAG ID and configure it in
hardware. When a port leaves a LAG, we have to destroy it only for the last
user. This code can be simplified, for such requirements we usually add
get() and put() functions which create and destroy the object.
Add mlxsw_sp_lag_{get,put}() and use them. These functions take care of
the reference counter and hardware configuration if needed. Change the
reference counter to refcount_t type which catches overflow and underflow
issues.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the function mlxsw_sp_lag_index_get() is called twice - first
as part of NETDEV_PRECHANGEUPPER event and later as part of
NETDEV_CHANGEUPPER. This function will be changed in the next patch. To
simplify the code, call it only once as part of NETDEV_CHANGEUPPER
event and set an error message using 'extack' in case of failure.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The maximum number of LAGs is queried from core several times. It is
used to allocate LAG array, and then to iterate over it. In addition, it
is used for PGT initialization. To simplify the code, instead of
querying it several times, store the value as part of 'mlxsw_sp' and use
it.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A next patch will add mlxsw_sp_lag_{get,put}() functions to handle LAG
reference counting and create/destroy it only for first user/last user.
Remove mlxsw_sp_lag_get() function and access LAG array directly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The structure mlxsw_sp_upper is used only as LAG. Rename it to
mlxsw_sp_lag and move it to spectrum.c file, as it is used only there.
Move the function mlxsw_sp_lag_get() with the structure.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When setting or getting PHC time, the higher bits of the second time (>32
bits) they were ignored. Meaning that setting some time in the future like
year 2150, it was failing to set this.
The issue can be reproduced like this:
# phc_ctl /dev/ptp1 set 10000000000
phc_ctl[12.290]: set clock time to 10000000000.000000000 or Sat Nov 20 17:46:40 2286
# phc_ctl /dev/ptp1 get
phc_ctl[15.309]: clock time is 1410065411.018055420 or Sun Sep 7 04:50:11 2014
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240126073042.1845153-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the inline function reciprocal_scale rather than open coding
the scale optimization. Also, remove unnecessary initializations.
Resulting compiled code is unchanged (according to godbolt).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240126002550.169608-1-stephen@networkplumber.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice driver currently attempts to destroy and re-initialize the Tx
timestamp tracker during the reset flow. The release of the Tx tracker
only happened during CORE reset or GLOBAL reset. The ice_ptp_rebuild()
function always calls the ice_ptp_init_tx function which will allocate
a new tracker data structure, resulting in memory leaks during PF reset.
Certainly the driver should not be allocating a new tracker without
removing the old tracker data, as this results in a memory leak.
Additionally, there's no reason to remove the tracker memory during a
reset. Remove this logic from the reset and rebuild flow. Instead of
releasing the Tx tracker, flush outstanding timestamps just before we
reset the PHY timestamp block in ice_ptp_cfg_phy_interrupt().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_reset() function uses a goto to skip past clock owner
operations if performing a PF reset or if the device is not the clock
owner. This is a bit confusing. Factor this out into
ice_ptp_rebuild_owner() instead.
The ice_ptp_reset() function is called by ice_rebuild() to restore PTP
functionality after a device reset. Follow the convention set by the
ice_main.c file and rename this function to ice_ptp_rebuild(), in the
same way that we have ice_prepare_for_reset() and
ice_ptp_prepare_for_reset().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_tx_cfg_intr() function sends a control queue message to
configure the PHY timestamp interrupt block. This is a very similar name
to a function which is used to configure the MAC Other Interrupt Cause
Enable register.
Rename this function to ice_ptp_cfg_phy_interrupt in order to make it
more obvious to the reader what action it performs, and distinguish it
from other similarly named functions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
E810 hardware does not have a Tx timestamp ready bitmap. Don't check
has_ready_bitmap in E810-specific functions.
Add has_ready_bitmap check in ice_ptp_process_tx_tstamp() to stop
relying on the fact that ice_get_phy_tx_tstamp_ready() returns all 1s.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The tx->verify_cached flag is used to inform the Tx timestamp tracking
code whether it needs to verify the cached Tx timestamp value against
a previous captured value. This is necessary on E810 hardware which does
not have a Tx timestamp ready bitmap.
In addition, we currently rely on the fact that the
ice_get_phy_tx_tstamp_ready() function returns all 1s for E810 hardware.
Instead of introducing a brand new flag, rename and verify_cached to
has_ready_bitmap, inverting the relevant checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_prepare_for_reset() and ice_ptp_reset() functions currently
check the pf->flags ICE_FLAG_PFR_REQ bit to determine if the current
reset is a PF reset or not.
This is problematic, because it is possible that a PF reset and a higher
level reset (CORE reset, GLOBAL reset, EMP reset) are requested
simultaneously. In that case, the driver performs the highest level
reset requested. However, the ICE_FLAG_PFR_REQ flag will still be set.
The main driver reset functions take an enum ice_reset_req indicating
which reset is actually being performed. Pass this data into the PTP
functions and rely on this instead of relying on the driver flags.
This ensures that the PTP code performs the proper level of reset that
the driver is actually undergoing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add PTP state machine so that the driver can correctly identify PTP
state around resets.
When the driver got information about ungraceful reset, PTP was not
prepared for reset and it returned error. When this situation occurs,
prepare PTP before rebuilding its structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There's no need to run all the code on mt7530_setup_port5() if port 5 is
disabled. The only case for calling mt7530_setup_port5() from
mt7530_setup() is when PHY muxing is enabled. That is because port 5 is not
defined as a port on the devicetree, therefore, it cannot be controlled by
phylink.
Because of this, run mt7530_setup_port5() if priv->p5_intf_sel is
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4. Remove the P5_DISABLED case from
mt7530_setup_port5().
Stop initialising the interface variable as the remaining cases will always
call mt7530_setup_port5() with it initialised.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-7-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Running mt7530_setup_port5() from mt7530_setup() used to handle all cases
of configuring port 5, including phylink.
Setting priv->p5_interface under mt7530_setup_port5() makes sure that
mt7530_setup_port5() from mt753x_phylink_mac_config() won't run.
The commit ("net: dsa: mt7530: improve code path for setting up port 5")
makes so that mt7530_setup_port5() from mt7530_setup() runs only on
non-phylink cases.
Get rid of unnecessarily setting priv->p5_interface under
mt7530_setup_port5() as port 5 phylink configuration will be done by
running mt7530_setup_port5() from mt753x_phylink_mac_config() now.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-6-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no logic to numerically order the CPU ports. Just state the port
number instead.
Remove the irrelevant PHY muxing information from
mt7530_mac_port_get_caps(). Explain the supported MII modes instead.
Remove the out of place PHY muxing information from
mt753x_phylink_mac_config(). The function is for MT7530, MT7531, and the
switch on the MT7988 SoC but there's no PHY muxing on MT7531 or the switch
on the MT7988 SoC.
These comments were gradually introduced with the commits below.
commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
commit 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
commit 88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding
a new hardware")
commit c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-4-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce the p5_sgmii field to store the information for whether port 5
has got SGMII or not. Instead of reading the MT7531_TOP_SIG_SR register
multiple times, the register will be read once and the value will be
stored on the p5_sgmii field. This saves unnecessary reads of the
register.
Move the comment about MT7531AE and MT7531BE to mt7531_setup(), where the
switch is identified.
Get rid of mt7531_dual_sgmii_supported() now that priv->p5_sgmii stores the
information. Address the code where mt7531_dual_sgmii_supported() is used.
Get rid of mt7531_is_rgmii_port() which just prints the opposite of
priv->p5_sgmii.
Instead of calling mt7531_pll_setup() then returning, do not call it if
port 5 is SGMII.
Remove P5_INTF_SEL_GMAC5_SGMII. The p5_interface_select enum is supposed to
represent the mode that port 5 is being used in, not the hardware
information of port 5. Set p5_intf_sel to P5_INTF_SEL_GMAC5 instead, if
port 5 is not dsa_is_unused_port().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-3-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the p5_interface_select enumeration as the data type for the
p5_intf_sel field. This ensures p5_intf_sel can only take the values
defined in the p5_interface_select enumeration.
Remove the explicit assignment of 0 to P5_DISABLED as the first enum item
is automatically assigned 0.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-2-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the MT7530 switch, the CPU_PORT field indicates which CPU port to trap
frames to, regardless of the affinity of the inbound user port.
When multiple CPU ports are in use, if the DSA conduit interface is down,
trapped frames won't be passed to the conduit interface.
To make trapping frames work including this case, implement
ds->ops->conduit_state_change() on this subdriver and set the CPU_PORT
field to the numerically smallest CPU port whose conduit interface is up.
Introduce the active_cpu_ports field to store the information of the active
CPU ports. Correct the macros, CPU_PORT is bits 4 through 6 of the
register.
Add a comment to explain frame trapping for this switch.
Currently, the driver doesn't support the use of multiple CPU ports so this
is not necessarily a bug fix.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-1-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RENESAS FemtoClock3 Wireless is a high-performance jitter attenuator,
frequency translator, and clock synthesizer. The device is comprised of 3
digital PLLs (DPLL) to track CLKIN inputs and three independent low phase
noise fractional output dividers (FOD) that output low phase noise clocks.
FemtoClock3 supports one Time Synchronization (Time Sync) channel to enable
an external processor to control the phase and frequency of the Time Sync
channel and to take phase measurements using the TDC. Intended applications
are synchronization using the precision time protocol (PTP) and
synchronization with 0.5 Hz and 1 Hz signals from GNSS.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change is for the PHC devices that can measure the phase offset
between PHC signal and the external signal, such as the 1PPS signal of
GNSS. Reporting PTP_CLOCK_EXTOFF to user space will be piggy-backed to
the existing ptp_extts_event so that application such as ts2phc can
poll the external offset the same way as extts. Hence, ts2phc can use
the offset to achieve the alignment between PHC and the external signal
by the help of either SW or HW filters.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to arcnet module.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Lynx, XPCS and LynxI PCS drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Beckhoff CX5020 EtherCAT Ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the TI CPSW switch module.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the STMicro DWMAC for Altera SOCs.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Qualcom rmnet and emac drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the SMSC 91x/911x/9420 Ethernet drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Ocelot SoCs (VSC7514) helpers driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Microchip ENCX24J600 helpers driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds hardware profile supports for extracting packet headers.
It makes sure that hardware is capabale of extracting ICMP, CPT, ERSPAN
headers.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8873
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-01-26
We've added 107 non-merge commits during the last 4 day(s) which contain
a total of 101 files changed, 6009 insertions(+), 1260 deletions(-).
The main changes are:
1) Add BPF token support to delegate a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application. With addressed changes from Christian
and Linus' reviews, from Andrii Nakryiko.
2) Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops type,
from Kui-Feng Lee.
3) Add support for retrieval of cookies for perf/kprobe multi links,
from Jiri Olsa.
4) Bigger batch of prep-work for the BPF verifier to eventually support
preserving boundaries and tracking scalars on narrowing fills,
from Maxim Mikityanskiy.
5) Extend the tc BPF flavor to support arbitrary TCP SYN cookies to help
with the scenario of SYN floods, from Kuniyuki Iwashima.
6) Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF objects,
from Hou Tao.
7) Extend BPF verifier to track aligned ST stores as imprecise spilled
registers, from Yonghong Song.
8) Several fixes to BPF selftests around inline asm constraints and
unsupported VLA code generation, from Jose E. Marchesi.
9) Various updates to the BPF IETF instruction set draft document such
as the introduction of conformance groups for instructions,
from Dave Thaler.
10) Fix BPF verifier to make infinite loop detection in is_state_visited()
exact to catch some too lax spill/fill corner cases,
from Eduard Zingerman.
11) Refactor the BPF verifier pointer ALU check to allow ALU explicitly
instead of implicitly for various register types, from Hao Sun.
12) Fix the flaky tc_redirect_dtime BPF selftest due to slowness
in neighbor advertisement at setup time, from Martin KaFai Lau.
13) Change BPF selftests to skip callback tests for the case when the
JIT is disabled, from Tiezhu Yang.
14) Add a small extension to libbpf which allows to auto create
a map-in-map's inner map, from Andrey Grafin.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (107 commits)
selftests/bpf: Add missing line break in test_verifier
bpf, docs: Clarify definitions of various instructions
bpf: Fix error checks against bpf_get_btf_vmlinux().
bpf: One more maintainer for libbpf and BPF selftests
selftests/bpf: Incorporate LSM policy to token-based tests
selftests/bpf: Add tests for LIBBPF_BPF_TOKEN_PATH envvar
libbpf: Support BPF token path setting through LIBBPF_BPF_TOKEN_PATH envvar
selftests/bpf: Add tests for BPF object load with implicit token
selftests/bpf: Add BPF object loading tests with explicit token passing
libbpf: Wire up BPF token support at BPF object level
libbpf: Wire up token_fd into feature probing logic
libbpf: Move feature detection code into its own file
libbpf: Further decouple feature checking logic from bpf_object
libbpf: Split feature detectors definitions from cached results
selftests/bpf: Utilize string values for delegate_xxx mount options
bpf: Support symbolic BPF FS delegation mount options
bpf: Fail BPF_TOKEN_CREATE if no delegation option was set on BPF FS
bpf,selinux: Allocate bpf_security_struct per BPF token
selftests/bpf: Add BPF token-enabled tests
libbpf: Add BPF token support to bpf_prog_load() API
...
====================
Link: https://lore.kernel.org/r/20240126215710.19855-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add LED support for QCA8081 PHY.
Documentation for this LEDs PHY is very scarce even with NDA access
to Documentation for OEMs. Only the blink pattern are documented and are
very confusing most of the time. No documentation is present about
forcing the LED on/off or to always blink.
Those settings were reversed by poking the regs and trying to find the
correct bits to trigger these modes. Some bits mode are not clear and
maybe the documentation option are not 100% correct. For the sake of LED
support the reversed option are enough to add support for current LED
APIs.
Supported HW control modes are:
- tx
- rx
- link_10
- link_100
- link_1000
- link_2500
- half_duplex
- full_duplex
Also add support for LED polarity set to set LED polarity to active
high or low. QSDK sets this value to high by default but PHY reset value
doesn't have this enabled by default.
QSDK also sets 2 additional bits but their usage is not clear, info about
this is added in the header. It was verified that for correct function
of the LED if active high is needed, only BIT 6 is needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for PHY LEDs polarity modes. Some PHY require LED to be set
to active low to be turned ON. Adds support for this by declaring
active-low property in DT.
PHY driver needs to declare .led_polarity_set() to configure LED
polarity modes. Function will pass the index with the LED index and a
bitmap with all the required modes to set.
Current supported modes are:
- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low
to turn it ON.
- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE.
LED is set to high impedance to turn it OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A potential string truncation was reported in bnx2x_fill_fw_str(),
when a long bp->fw_ver and a long phy_fw_ver might coexist, but seems
unlikely with real-world hardware.
Use scnprintf() to indicate the intent that truncations are tolerated.
While reading this code, I found a collection of various buffer size
counting issues. None looked like they might lead to a buffer overflow
with current code (the small buffers are 20 bytes and might only ever
consume 10 bytes twice with a trailing %NUL). However, early truncation
(due to a %NUL in the middle of the string) might be happening under
likely rare conditions. Regardless fix the formatters and related
functions:
- Switch from a separate strscpy() to just adding an additional "%s" to
the format string that immediately follows it in bnx2x_fill_fw_str().
- Use sizeof() universally instead of using unbound defines.
- Fix bnx2x_7101_format_ver() and bnx2x_null_format_ver() to report the
number of characters written, not including the trailing %NUL (as
already done with the other firmware formatting functions).
- Require space for at least 1 byte in bnx2x_get_ext_phy_fw_version()
for the trailing %NUL.
- Correct the needed buffer size in bnx2x_3_seq_format_ver().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401260858.jZN6vD1k-lkp@intel.com/
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240126041044.work.220-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
> ./drivers/ptp/ptp_sysfs.c:27:8-16: WARNING: please use sysfs_emit
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240125015329.123023-1-lizhijian@fujitsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
