| Age | Commit message (Collapse) | Author |
|---|
|
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 3900f29021f0bc7fe9815aa32f1a993b7dfdd402 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.
The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All accesses to ipvlan->addrs are under rtnl.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding and removing to the 'ipvlans' list is already done using _rcu list
operations.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ipvlan interface with IP addresses attached is brought down and then
deleted, the assigned addresses are deleted twice from the address hash
list, first on the interface down and second on the link deletion.
Similarly, when an address is added while the interface is down, it is added
second time once the interface is brought up.
When the interface is down, the addresses should be kept off the hash list
for performance reasons. Ensure this is true, which also fixes the double add
problem. To fix the double free, check whether the address is hashed before
removing it.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.
This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes sparse warnings introduced in commit e85c9a7abfa407ed ("cxgb4/cxgb4vf: Add
code to calculate T5 BAR2 Offsets for SGE Queue Registers") and
df64e4d38c904dd3 ("cxgb4/cxgb4vf: Use new interfaces to calculate BAR2 SGE Queue
Register addresses") and few old ones
sparse warnings:
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: cast removes
>> address space of expression
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: incorrect type in
>> initializer (different address space)
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1020:40: sparse: incorrect type in
>> argument 1 (different base types)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable interrupts and quiesce rx before unregistering net device to avoid crash
while unloading driver when traffic is flowing through.
Based on original work by Shameem Khalid <shameem@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).
The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.
Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3b4 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
|
|
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes below warning by dynamically allocating memory
All warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c: In function
'cctrl_tbl_show':
>> drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:689:1: warning: the
>> frame
>> size of 1028 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ucc_geth was indicating link up after a port is administratively enabled even
when nothing is plugged in. This causes user-space tools to see a spurious link
up the first time after boot.
Signed-off-by: Cliff Clark <cliff_clark@selinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We occasionally see in procedure mlx4_GEN_EQE that the driver tries
to grab an uninitialized mutex.
This can occur in only one of two ways:
1. We are trying to generate an async event on an uninitialized slave.
2. We are trying to generate an async event on an illegal slave number
( < 0 or > persist->num_vfs) or an inactive slave.
To deal with #1: move the mutex initialization from specific slave init
sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that
the mutex is always initialized for all slaves).
To deal with #2: check in procedure mlx4_GEN_EQE that the slave number
provided is in the proper range and that the slave is active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0ccc5 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.
Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.
This patch makes provision for doing nothing in such cases.
Fixes: 6c7079450071f ("rocker: implement L2 bridge offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-22
this is a pull-request of 7 patches for net/master.
Ahmed S. Darwish fixes another two problems in the kvaser_usb driver. A patch
by Colin Ian King for the gs_usb driver adds a missing check for kzalloc
allocation failures. Two patches by Stephane Grosjean for the peak_usb driver
add missing support for ISO / non-ISO mode switching. Andri Yngvason
contributes a patch to fix the state handling in the flexcan driver. The last
patch by Andreas Werner for the flexcan driver add missing EPROBE_DEFER
handling for the transceiver regulator.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Validate iov ranges before feeding them into iov_iter_init(), from
Al Viro.
2) We changed copy_from_msghdr_from_user() to zero out the msg_namelen
is a NULL pointer is given for the msg_name. Do the same in the
compat code too. From Catalin Marinas.
3) Fix partially initialized tuples in netfilter conntrack helper, from
Ian Wilson.
4) Missing continue; statement in nft_hash walker can lead to crashes,
from Herbert Xu.
5) tproxy_tg6_check looks for IP6T_INV_PROTO in ->flags instead of
->invflags, fix from Pablo Neira Ayuso.
6) Incorrect memory account of TCP FINs can result in negative socket
memory accounting values. Fix from Josh Hunt.
7) Don't allow virtual functions to enable VLAN promiscuous mode in
be2net driver, from Vasundhara Volam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: nft_compat: set IP6T_F_PROTO flag if protocol is set
cx82310_eth: wait for firmware to become ready
net: validate the range we feed to iov_iter_init() in sys_sendto/sys_recvfrom
net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
be2net: use PCI MMIO read instead of config read for errors
be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs
be2net: Prevent VFs from enabling VLAN promiscuous mode
tcp: fix tcp fin memory accounting
ipv6: fix backtracking for throw routes
net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}
ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in udp6_ufo_fragment
netfilter: xt_TPROXY: fix invflags check in tproxy_tg6_check()
netfilter: restore rule tracing via nfnetlink_log
netfilter: nf_tables: allow to change chain policy without hook if it exists
netfilter: Fix potential crash in nft_hash walker
netfilter: Zero the tuple in nfnl_cthelper_parse_tuple()
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
|
|
Pull bugfix for md from Neil Brown:
"One fix for md in 4.0-rc4
Regression in recent patch causes crash on error path"
* tag 'md/4.0-rc4-fix' of git://neil.brown.name/md:
md: fix problems with freeing private data after ->run failure.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
were merged in 4.0-rc1 that cause regressions. So let's revert them
for now and they will be reworked and resent sometime in the future.
All have been tested in linux-next for a while"
* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "pcmcia: add a new resource manager for non ISA systems"
Revert "pcmcia: fix incorrect bracketing on a test"
Revert "pcmcia: add missing include for new pci resource handler"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are four small staging driver fixes, all for the vt6656 and
vt6655 drivers, that resolve some reported issues with them.
All of these patches have been in linux next for a while"
* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
vt6655: Fix late setting of byRFType.
vt6655: RFbSetPower fix missing rate RATE_12M
staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
staging: vt6655: vnt_tx_packet fix dma_idx selection.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fix from Greg KH:
"Here's a single 8250 serial driver that fixes a reported deadlock with
the serial console and the tty driver.
It's been in linux-next for a while now"
* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Fix deadlock in LCR workaround
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here's a number of USB and PHY driver fixes for 4.0-rc5.
The largest thing here is a revert of a gadget function driver patch
that removes 500 lines of code. Other than that, it's a number of
reported bugs fixes and new quirk/id entries.
All have been in linux-next for a while"
* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: common: otg-fsm: only signal connect after switching to peripheral
uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
USB: ehci-atmel: rework clk handling
MAINTAINERS: add entry for USB OTG FSM
usb: chipidea: otg: add a_alt_hnp_support response for B device
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
phy: ti/omap: Fix modalias
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
phy: Find the right match in devm_phy_destroy()
phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
phy: samsung-usb2: Remove NULL terminating entry from phys array
phy: hix5hd2-sata: Check return value of platform_get_resource
phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
Revert "usb: gadget: zero: Add support for interrupt EP"
Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
...
|
|
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull slave dmaengine fixes from Vinod Koul:
"Four fixes for dw, pl08x, imx-sdma and at_hdmac driver. Nothing
unusual here, simple fixes to these drivers"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pl08x: Define capabilities for generic capabilities reporting
dmaengine: dw: append MODULE_ALIAS for platform driver
dmaengine: imx-sdma: switch to dynamic context mode after script loaded
dmaengine: at_hdmac: Fix calculation of the residual bytes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (PCI/ACPI resources and at91
RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
cpuidle fixes (one stable-candidate too).
Specifics:
- Revert a recent PCI commit related to IRQ resources management that
introduced a regression for drivers attempting to bind to devices
whose previous drivers did not balance pci_enable_device() and
pci_disable_device() as expected (Rafael J Wysocki).
- Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
recent commit related to wakeup interrupt handling (Dan Carpenter).
- Allow the power capping RAPL (Running-Average Power Limit) driver
to use different energy units for domains within one CPU package
which is necessary to handle Intel Haswell EP processors correctly
(Jacob Pan).
- Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
updating the target residency and exit latency numbers for those
chips (Sebastien Rannou).
- Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
in a row before cpu_pm_exit() is called on the same CPU which
breaks the core's assumptions regarding the usage of those
functions (Gregory Clement)"
* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
powercap / RAPL: handle domains with different energy units
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
|
|
Pull drm updates from Dave Airlie:
"A bunch of fixes across drivers:
radeon:
disable two ended allocation for now, it breaks some stuff
amdkfd:
misc fixes
nouveau:
fix irq loop problem, add basic support for GM206 (new hw)
i915:
fix some WARNs people were seeing
exynos:
fix some iommu interactions causing boot failures"
* git://people.freedesktop.org/~airlied/linux:
drm/radeon: drop ttm two ended allocation
drm/exynos: fix the initialization order in FIMD
drm/exynos: fix typo config name correctly.
drm/exynos: Check for NULL dereference of crtc
drm/exynos: IS_ERR() vs NULL bug
drm/exynos: remove unused files
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more DeviceTree fixes vfom Rob Herring:
- revert setting stdout-path as preferred console. This caused
regressions in PowerMACs and other systems.
- yet another fix for stdout-path option parsing.
- fix error path handling in of_irq_parse_one
* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Revert "of: Fix premature bootconsole disable with 'stdout-path'"
of: handle both '/' and ':' in path strings
of: unittest: Add option string test case with longer path
of/irq: Fix of_irq_parse_one() returned error codes
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are current target-pending fixes for v4.0-rc5 code that have made
their way into the queue over the last weeks.
The fixes this round include:
- Fix long-standing iser-target logout bug related to early
conn_logout_comp completion, resulting in iscsi_conn use-after-tree
OOpsen. (Sagi + nab)
- Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
handing for DDP hw offload. (DanC)
- Fix incorrect use of unprotected __transport_register_session() in
tcm_qla2xxx + other single local se_node_acl fabrics. (Bart)
- Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
for ack_kref=1 failure path. (Bart)
- Fix pSCSI backend ->get_device_type() statistics OOPs with
un-configured device. (Olaf + nab)
- Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
time. (Claudio + nab)
- Fix FUA write false positive failure regression in v4.0-rc1 code.
(Christophe Vu-Brugier + HCH)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
target: Fix virtual LUN=0 target_configure_device failure OOPs
target/pscsi: Fix NULL pointer dereference in get_device_type
tcm_fc: missing curly braces in ft_invl_hw_context()
target: Fix reference leak in target_get_sess_cmd() error path
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
tcm_qla2xxx: Fix incorrect use of __transport_register_session
iscsi-target: Avoid early conn_logout_comp for iser connections
Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
target: Disallow changing of WRITE cache/FUA attrs after export
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull devicemapper fixes from Mike Snitzer:
"A handful of stable fixes for DM:
- fix thin target to always zero-fill reads to unprovisioned blocks
- fix to interlock device destruction's suspend from internal
suspends
- fix 2 snapshot exception store handover bugs
- fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing"
* tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME
dm snapshot: suspend merging snapshot when doing exception handover
dm snapshot: suspend origin when doing exception handover
dm: hold suspend_lock while suspending device during device deletion
dm thin: fix to consistently zero-fill reads to unprovisioned blocks
|
|
Pull UBI fix from Artem Bityutskiy:
"This fixes a bug introduced during the v4.0 merge window where we
forgot to put braces where they should be"
* tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs:
UBI: fix missing brace control flow
|
|
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
* pm-cpuidle:
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
* powercap:
powercap / RAPL: handle domains with different energy units
* irq-pm:
rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
* acpi-resources:
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
|
|
If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.
However:
md.c calls ->free() even if ->private_data is NULL, which
causes problems in some personalities.
raid0.c frees the data, but doesn't clear ->private_data,
which will become a problem when we fix md.c
So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
