| Age | Commit message (Collapse) | Author |
|---|
|
Fix clamping to match register field size
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
pflip interrupt order are mapped 1 to 1 to otg id.
e.g. if irq_src=26 corresponds to otg0 then 27->otg1, 28->otg2...
Linux DM registers pflip interrupts per number of crtcs.
In fused pipe case crtc numbers can be less than otg id.
e.g. if one pipe out of 3(otg#0-2) is fused adev->mode_info.num_crtc=2
so DM only registers irq_src 26,27.
This is a bug since if pipe#2 remains unfused DM never gets
otg2 pflip interrupt (irq_src=28)
That may results in gfx failure due to pflip timeout.
[How]
Register pflip interrupts per max num of otg instead of num_crtc
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Confirmed with hardware team, there is harvesting for gc 10.3.1.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A number of BIOS versions have a problem with the watermarks table not
being configured properly. This manifests as a very scary looking warning
during resume from s0i3. This should be harmless in most cases and is well
understood, so decrease the assertion to a clearer warning about the problem.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 24e516049360 ("ACPI/IORT: Add support for PMCG")
Cc: <stable@vger.kernel.org> # 5.2.x
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix two regressions:
- Potential boot failure due to missing cryptomgr on initramfs
- Stack overflow in octeontx2"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Move cryptomgr soft dependency into algapi
crypto: octeontx2 - Avoid stack variable overflow
|
|
AER is not backed by a real request, hence we should not incorrectly
assume that when failing to send a nvme command, it is a normal request
but rather check if this is an aer and if so complete the aer (similar
to the normal completion path).
Cc: stable@vger.kernel.org
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add NVMe request completion trace in nvme_complete_batch_req() because
nvme:nvme_complete_req tracepoint is missing in case of request batched
completion.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Hardware interrupts are enabled during the pci probe, however,
they are not disabled during pci removal.
Disable all hardware interrupts during pci removal to avoid any
issues.
Fixes: e75377404726 ("amd-xgbe: Update PCI support to use new IRQ functions")
Suggested-by: Selwin Sebastian <Selwin.Sebastian@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix loading of the driver when built as a module.
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
veth being NETIF_F_LLTX enabled, we need to be more careful
whenever we read/write rq->rx_notify_masked.
BUG: KCSAN: data-race in veth_xmit / veth_xmit
write to 0xffff888133d9a9f8 of 1 bytes by task 23552 on cpu 0:
__veth_xdp_flush drivers/net/veth.c:269 [inline]
veth_xmit+0x307/0x470 drivers/net/veth.c:350
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
NF_HOOK include/linux/netfilter.h:307 [inline]
br_forward_finish net/bridge/br_forward.c:66 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
__br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
br_dev_xmit+0x8b6/0x960
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
neigh_hh_output include/net/neighbour.h:525 [inline]
neigh_output include/net/neighbour.h:539 [inline]
ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:451 [inline]
ip_local_out net/ipv4/ip_output.c:126 [inline]
ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888133d9a9f8 of 1 bytes by task 23563 on cpu 1:
__veth_xdp_flush drivers/net/veth.c:268 [inline]
veth_xmit+0x2d6/0x470 drivers/net/veth.c:350
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
NF_HOOK include/linux/netfilter.h:307 [inline]
br_forward_finish net/bridge/br_forward.c:66 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
__br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
br_dev_xmit+0x8b6/0x960
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
neigh_hh_output include/net/neighbour.h:525 [inline]
neigh_output include/net/neighbour.h:539 [inline]
ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:451 [inline]
ip_local_out net/ipv4/ip_output.c:126 [inline]
ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23563 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00064-gc36c04c2e132 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 948d4f214fde ("veth: Add driver XDP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always assign the default device name as the chip_label in hog
structures which makes it impossible to assign hogs to chips. Let's
first check if a custom label was set and then copy it instead of the
default device name.
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT
that gets set if nfp_flower_is_supported_bridge is true is not taken
into account. Consequently the path that should release the ida_index
in cleanup is never triggered, causing messages like:
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to
new tunnel flows not being offloaded.
Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if
the port is of type OTHER.
Fixes: 2e0bc7f3cb55 ("nfp: flower: encode mac indexes with pre-tunnel rule check")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LiteX driver uses devm io function API which
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: ee7da21ac4c3 ("net: Add driver for LiteX's LiteETH network interface")
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220208013308.6563-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If __ibmvnic_open() encounters an error such as when setting link state,
it calls release_resources() which frees the napi structures needlessly.
Instead, have __ibmvnic_open() only clean up the work it did so far (i.e.
disable napi and irqs) and leave the rest to the callers.
If caller of __ibmvnic_open() is ibmvnic_open(), it should release the
resources immediately. If the caller is do_reset() or do_hard_reset(),
they will release the resources on the next reset.
This fixes following crash that occurred when running the drmgr command
several times to add/remove a vnic interface:
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[6] irq
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[7] irq
[102056] ibmvnic 30000003 env3: Replenished 8 pools
Kernel attempted to read user page (10) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000010
Faulting instruction address: 0xc000000000a3c840
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
CPU: 9 PID: 102056 Comm: kworker/9:2 Kdump: loaded Not tainted 5.16.0-rc5-autotest-g6441998e2e37 #1
Workqueue: events_long __ibmvnic_reset [ibmvnic]
NIP: c000000000a3c840 LR: c0080000029b5378 CTR: c000000000a3c820
REGS: c0000000548e37e0 TRAP: 0300 Not tainted (5.16.0-rc5-autotest-g6441998e2e37)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28248484 XER: 00000004
CFAR: c0080000029bdd24 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0
GPR00: c0080000029b55d0 c0000000548e3a80 c0000000028f0200 0000000000000000
...
NIP [c000000000a3c840] napi_enable+0x20/0xc0
LR [c0080000029b5378] __ibmvnic_open+0xf0/0x430 [ibmvnic]
Call Trace:
[c0000000548e3a80] [0000000000000006] 0x6 (unreliable)
[c0000000548e3ab0] [c0080000029b55d0] __ibmvnic_open+0x348/0x430 [ibmvnic]
[c0000000548e3b40] [c0080000029bcc28] __ibmvnic_reset+0x500/0xdf0 [ibmvnic]
[c0000000548e3c60] [c000000000176228] process_one_work+0x288/0x570
[c0000000548e3d00] [c000000000176588] worker_thread+0x78/0x660
[c0000000548e3da0] [c0000000001822f0] kthread+0x1c0/0x1d0
[c0000000548e3e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
7d2948f8 792307e0 4e800020 60000000 3c4c01eb 384239e0 f821ffd1 39430010
38a0fff6 e92d1100 f9210028 39200000 <e9030010> f9010020 60420000 e9210020
---[ end trace 5f8033b08fd27706 ]---
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220208001918.900602-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This caused a significant performance degredation when using generic XDP
with multiple queues.
Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Tao Liu <xliutaox@google.com>
Link: https://lore.kernel.org/r/20220207175901.2486596-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 7707f7227f09 ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f09. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f09 ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
|
|
The driver returns an error when devm_phy_optional_get() fails leaving
the previously enabled clock turned on. Change order and enable the
clock only after the phy has been acquired.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126145549.617165-3-s.hauer@pengutronix.de
|
|
Fix this kernel test robot warning:
drivers/video/fbdev/core/fbcon.c: In function 'fbcon_init':
drivers/video/fbdev/core/fbcon.c:1028:6: warning: variable 'cap' set but not used [-Wunused-but-set-variable]
The cap variable is only used when CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
is enabled. Drop the temporary variable and use info->flags instead.
Fixes: 87ab9f6b7417 ("Revert "fbcon: Disable accelerated scrolling")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YgFB4xqI+As196FR@p100
|
|
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c9d ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
d97a9d7aea04 ("staging/speakup: Add inflection synth parameter")
introduced the inflection parameter, but happened to drop the pitch
parameter from the dectlk driver. This restores it.
Cc: stable@vger.kernel.org
Fixes: d97a9d7aea04 ("staging/speakup: Add inflection synth parameter")
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20220206015626.aesbhvvdkmqsrbaw@begin
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Setting the output of a GPIO to 1 using gpiod_set_value(), followed by
reading the same GPIO using gpiod_get_value(), will currently yield an
incorrect result.
This is because the SiFive GPIO device stores the output values in reg_set,
not reg_dat.
Supply the flag BGPIOF_READ_OUTPUT_REG_SET to bgpio_init() so that the
generic driver reads the correct register.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Bartosz: added the Fixes tag]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Currently it's possible that character device interface may return
the error codes which are not supposed to be seen by user space.
In this case it's EPROBE_DEFER.
Wrap it to return -ENODEV instead as sysfs does.
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Reported-by: Suresh Balakrishnan <suresh.balakrishnan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Add a checking code when it gets -EPROBE_DEFER while getting a clock
resource. In this case, it doesn't need to print out an error message
because the probing will be re-visited.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20211104173709.222912-1-jae.hyun.yoo@intel.com
Link: https://lore.kernel.org/r/20220201070118.196372-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/fixes
Samsung fixes for v5.17
1. Typo in CONFIG_EXYNOS_USI description.
2. Add Alim Akhtar as a reviewer for Samsung Exynos platform.
* tag 'samsung-fixes-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: Fix typo in CONFIG_EXYNOS_USI description
MAINTAINERS: add reviewer entry for Samsung/Exynos platform
Link: https://lore.kernel.org/r/20220129115442.13474-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
OP-TE fixes for v5.17
- Adds error checking in optee_ffa_do_call_with_arg()
- Reintroduces an accidentally lost fix for a memref size check
- Uses bitmap_free() to free memory obtained with bitmap_zalloc()
* tag 'optee-fixes-for-v5.17' of git://git.linaro.org/people/jens.wiklander/linux-tee:
optee: add error checks in optee_ffa_do_call_with_arg()
tee: optee: do not check memref size on return from Secure World
optee: Use bitmap_free() to free bitmap
Link: https://lore.kernel.org/r/20220126102609.GA1516258@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Use the %u format for unsigned int parameters handling with sscanf() and
sysfs_emit() to avoid compilation warnings. In
fsl_sata_rx_watermark_store(), the call to sscanf() to parse a single
argument is replaced with a call to kstrtouint().
While at it, also replace the printk(KERN_ERR) calls with dev_err()
calls and fix blank lines in fsl_sata_rx_watermark_store().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Messages around firmware download were incorrectly tagged as being related
to discovery trace events. Thus, firmware download status ended up dumping
the trace log as well as the firmware update message. As there were a
couple of log messages in this state, the trace log was dumped multiple
times.
Resolve this by converting from trace events to SLI events.
Link: https://lore.kernel.org/r/20220207180442.72836-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver is initiating NVMe PRLIs to determine device NVMe support. This
should not be occurring if CONFIG_NVME_FC support is disabled.
Correct this by changing the default value for FC4 support. Currently it
defaults to FCP and NVMe. With change, when NVME_FC support is not enabled
in the kernel, the default value is just FCP.
Link: https://lore.kernel.org/r/20220207180516.73052-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
"A single patch from me, to fix a bug that is causing boot issues in
the field (reports of problems with Fedora 35).
The bug affects mostly old-ish drives that have issues with read log
page command handling"
* tag 'ata-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: Fix ata_dev_config_cpr()
|
|
After commit e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while
suspended to idle") made acpi_ec_dispatch_gpe() check
pm_wakeup_pending(), but that is before canceling the SCI wakeup,
so pm_wakeup_pending() is always true. This causes the loop in
acpi_ec_dispatch_gpe() to always terminate after one iteration which
may not be correct.
Address this issue by canceling the SCI wakeup earlier, from
acpi_ec_dispatch_gpe() itself.
Fixes: 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while suspended to idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Testing on various upcoming OEM systems shows commit 7b167c4cb48e ("ACPI:
PM: Only mark EC GPE for wakeup on Intel systems") was short
sighted and the symptoms were indicative of other problems. Some OEMs
do have the dedicated GPIOs for the power button but also rely upon
an interrupt to the EC SCI to let the lid work.
The original commit showed spurious activity on Lenovo systems:
* On both Lenovo T14 and P14s the keyboard wakeup doesn't work, and
sometimes the power button event doesn't work.
This was confirmed on my end at that time.
However further development in the kernel showed that the issue was
actually the IRQ for the GPIO controller was also shared with the EC SCI.
This was actually fixed by commit 2d54067fcd23 ("pinctrl: amd: Fix
wakeups when IRQ is shared with SCI").
The original commit also showed problems with AC adapter:
* On HP 635 G7 detaching or attaching AC during suspend will cause
the system not to wakeup
* On Asus vivobook to prevent detaching AC causing resume problems
* On Lenovo 14ARE05 to prevent detaching AC causing resume problems
* On HP ENVY x360 to prevent detaching AC causing resume problems
Detaching AC adapter causing problems appears to have been a problem
because the EC SCI went off to notify the OS of the power adapter change
but the SCI was ignored and there was no other way to wake up this system
since GPIO controller wasn't properly enabled. The wakeups were fixed by
enabling the GPIO controller in commit acd47b9f28e5 ("pinctrl: amd: Handle
wake-up interrupt").
I've confirmed on a variety of OEM notebooks with the following test
1) echo 1 | sudo tee /sys/power/pm_debug_messages
2) sudo systemctl suspend
3) unplug AC adapter, make sure system is still asleep
4) wake system from lid (which is provided by ACPI SCI on some of them)
5) dmesg
a) see the EC GPE dispatched, timekeeping for X seconds (matching ~time
until AC adapter plug out)
b) see timekeeping for Y seconds until woke (matching ~time from AC
adapter until lid event)
6) Look at /sys/kernel/debug/amd_pmc/s0ix_stats
"Time (in us) in S0i3" = X + Y - firmware processing time
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix support for SD Power off notification
MMC host:
- moxart: Fix potential use-after-free on remove path
- sdhci-of-esdhc: Fix error path when setting dma mask
- sh_mmcif: Fix potential NULL pointer dereference"
* tag 'mmc-v5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
moxart: fix potential use-after-free on remove path
mmc: core: Wait for command setting 'Power Off Notification' bit to complete
mmc: sh_mmcif: Check for null res pointer
mmc: sdhci-of-esdhc: Check for error num after setting mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
A series of fixes for omap variants for minor issues, and a fix for a timer
regression for some omap3 beagleboard versions.
The timer fix needs to patch both the dts and the timer code because
otherwise the timer quirk handling for old dtbs will prevent the dts fix
from working.
The other changes are for issues found by automated analysis, a macasp
typo fix, and two cosmetic fixes for clocks.
* tag 'omap-for-v5.17/fixes-for-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Don't use legacy clock defines for dra7 clkctrl
clk: ti: Move dra7 clock devices out of the legacy section
ARM: dts: Fix timer regression for beagleboard revision c
ARM: dts: am335x-wega: Fix typo in mcasp property rx-num-evt
ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of
ARM: OMAP2+: hwmod: Add of_node_put() before break
Link: https://lore.kernel.org/r/pull-1641801310-149268@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
OP-TEE fix shutdown problems
* tag 'optee-fix-for-v5.17' of git://git.linaro.org/people/jens.wiklander/linux-tee:
optee: use driver internal tee_context for some rpc
Link: https://lore.kernel.org/r/20220203132323.GA4132001@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The concurrent positioning ranges log page 47h is a general purpose log
page and not a subpage of the indentify device log. Using
ata_identify_page_supported() to test for concurrent positioning ranges
support is thus wrong. ata_log_supported() must be used.
Furthermore, unlike other advanced ATA features (e.g. NCQ priority),
accesses to the concurrent positioning ranges log page are not gated by
a feature bit from the device IDENTIFY data. Since many older drives
react badly to the READ LOG EXT and/or READ LOG DMA EXT commands isued
to read device log pages, avoid problems with older drives by limiting
the concurrent positioning ranges support detection to drives
implementing at least the ACS-4 ATA standard (major version 11). This
additional condition effectively turns ata_dev_config_cpr() into a nop
for older drives, avoiding problems in the field.
Fixes: fe22e1c2f705 ("libata: support concurrent positioning ranges log")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215519
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Abderraouf Adjal <adjal.arf@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Fix the following warning from "make htmldocs":
drivers/gpu/drm/drm_privacy_screen.c:270:
WARNING: Inline emphasis start-string without end-string.
Fixes: 8a12b170558a ("drm/privacy-screen: Add notifier support (v2)")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://lore.kernel.org/r/20220207130407.389585-1-hdegoede@redhat.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220207130407.389585-1-hdegoede@redhat.com
|
|
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb3975a8c2366e3883337e252bb0eee5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
During readout we cannot assume the planes are actually using the
slices they are supposed to use. The BIOS may have misprogrammed
things and put the planes onto the wrong dbuf slices. So let's
do the readout more carefully to make sure we really know which
dbuf slices are actually in use by the pipe at the time.
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit b3dcc6dc0f32612d04839c2fb32e94d0ebf92c98)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
