| Age | Commit message (Collapse) | Author |
|---|
|
Currently the phy reset sequence is as shown below for a
devicetree described mdio phy on boot:
1. Assert the phy_device's reset as part of registering
2. Deassert the phy_device's reset as part of registering
3. Deassert the phy_device's reset as part of phy_probe
4. Deassert the phy_device's reset as part of phy_hw_init
The extra two deasserts include waiting the deassert delay afterwards,
which is adding unnecessary delay.
This applies to both possible types of resets (reset controller
reference and a reset gpio) that can be used.
Here's some snipped tracing output using the following command line
params "trace_event=gpio:* trace_options=stacktrace" illustrating
the reset handling and where its coming from:
/* Assert */
systemd-udevd-283 [002] ..... 6.780434: gpio_value: 544 set 0
systemd-udevd-283 [002] ..... 6.783849: <stack trace>
=> gpiod_set_raw_value_commit
=> gpiod_set_value_nocheck
=> gpiod_set_value_cansleep
=> mdio_device_reset
=> mdiobus_register_device
=> phy_device_register
=> fwnode_mdiobus_phy_device_register
=> fwnode_mdiobus_register_phy
=> __of_mdiobus_register
=> stmmac_mdio_register
=> stmmac_dvr_probe
=> stmmac_pltfr_probe
=> devm_stmmac_pltfr_probe
=> qcom_ethqos_probe
=> platform_probe
/* Deassert */
systemd-udevd-283 [002] ..... 6.802480: gpio_value: 544 set 1
systemd-udevd-283 [002] ..... 6.805886: <stack trace>
=> gpiod_set_raw_value_commit
=> gpiod_set_value_nocheck
=> gpiod_set_value_cansleep
=> mdio_device_reset
=> phy_device_register
=> fwnode_mdiobus_phy_device_register
=> fwnode_mdiobus_register_phy
=> __of_mdiobus_register
=> stmmac_mdio_register
=> stmmac_dvr_probe
=> stmmac_pltfr_probe
=> devm_stmmac_pltfr_probe
=> qcom_ethqos_probe
=> platform_probe
/* Deassert */
systemd-udevd-283 [002] ..... 6.882601: gpio_value: 544 set 1
systemd-udevd-283 [002] ..... 6.886014: <stack trace>
=> gpiod_set_raw_value_commit
=> gpiod_set_value_nocheck
=> gpiod_set_value_cansleep
=> mdio_device_reset
=> phy_probe
=> really_probe
=> __driver_probe_device
=> driver_probe_device
=> __device_attach_driver
=> bus_for_each_drv
=> __device_attach
=> device_initial_probe
=> bus_probe_device
=> device_add
=> phy_device_register
=> fwnode_mdiobus_phy_device_register
=> fwnode_mdiobus_register_phy
=> __of_mdiobus_register
=> stmmac_mdio_register
=> stmmac_dvr_probe
=> stmmac_pltfr_probe
=> devm_stmmac_pltfr_probe
=> qcom_ethqos_probe
=> platform_probe
/* Deassert */
NetworkManager-477 [000] ..... 7.023144: gpio_value: 544 set 1
NetworkManager-477 [000] ..... 7.026596: <stack trace>
=> gpiod_set_raw_value_commit
=> gpiod_set_value_nocheck
=> gpiod_set_value_cansleep
=> mdio_device_reset
=> phy_init_hw
=> phy_attach_direct
=> phylink_fwnode_phy_connect
=> __stmmac_open
=> stmmac_open
There's a lot of paths where the device is getting its reset
asserted and deasserted. Let's track the state and only actually
do the assert/deassert when it changes.
Reported-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231127-net-phy-reset-once-v2-1-448e8658779e@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The quotes symbol in
"EEE "link partner ability 1
should be at the end of the register name
"EEE link partner ability 1"
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following unlocked accessors to complete the set:
__mdiobus_modify()
__mdiodev_read()
__mdiodev_write()
__mdiodev_modify()
__mdiodev_modify_changed()
which we will need for Marvell DSA PCS conversion.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new operations for a mdio device to manage the refcount on the
underlying struct device. This will be used by mdio PCS drivers to
simplify the creation and destruction handling, making it easier for
users to get it correct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper to convert a clause 73 advertisement to an ethtool bitmap.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add replacement for phy_ethtool_get/set_eee() functions.
Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
specification beyond Clause 22. The better place for this code is
phy-c45.c
- currently it is able to do read/write operations on PHYs with
different abilities to not existing registers. It is better to
use stored supported_eee abilities to avoid false read/write
operations.
- the eee_active detection will provide wrong results on not supported
link modes. It is better to validate speed/duplex properties against
supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
EEE link modes...
By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
(Register 1.2295)
Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.
Results of EEE ability detection will be stored into new variable
phydev->supported_eee.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The old way of performing a C45 bus transfer created a special
register value and passed it to the MDIO bus driver, in the hope it
would see the MII_ADDR_C45 bit set, and perform a C45 transfer. Now
that there is a clear separation of C22 and C45, this scheme is no
longer used. Remove all the #defines and helpers, to prevent any code
being added which tries to use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some DSA devices pass through PHY access to the MDIO bus the switch is
on. Add C45 versions of the current C22 helpers for nested accesses to
MDIO busses, so that C22 and C45 can be separated in these DSA
drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that mdiobus_c45_addr() is only used within the MDIO code during
fallback, move the function next to its only users. This function
should not be used any more in drivers, the c45 helpers should be used
in its place, so hiding it away will prevent any new users from being
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently C22 and C45 transactions are mixed over a combined API calls
which make use of a special bit in the reg address to indicate if a
C45 transaction should be performed. This makes it impossible to know
if the bus driver actually supports C45. Additionally, many C22 only
drivers don't return -EOPNOTSUPP when asked to perform a C45
transaction, they mistaking perform a C22 transaction.
This is the first step to cleanly separate C22 from C45. To maintain
backwards compatibility until all drivers which are capable of
performing C45 are converted to this new API, the helper functions
will fall back to the older API if the new API is not
supported. Eventually this fallback will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a couple of helpers and definitions to extract the clause 45 regad
and devad fields from the regnum passed into MDIO drivers.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds some helpers for accessing non-phy MDIO devices. They are
analogous to phy_(read|write|modify), except that they take an mdio_device
and not a phy_device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726e9 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
container_of() macro hides a local variable '__mptr' inside. This
becomes a problem when several container_of() are nested in each
other within single line or plain macros.
As C preprocessor doesn't support generating random variable names,
the sole solution is to avoid defining macros that consist only of
container_of() calls, or they will self-shadow '__mptr' each time:
In file included from ./include/linux/bitmap.h:10,
from drivers/net/phy/phy_device.c:12:
drivers/net/phy/phy_device.c: In function ‘phy_device_release’:
./include/linux/kernel.h:693:8: warning: declaration of ‘__mptr’ shadows a previous local [-Wshadow]
693 | void *__mptr = (void *)(ptr); \
| ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~
./include/linux/mdio.h:52:27: note: in expansion of macro ‘container_of’
52 | #define to_mdio_device(d) container_of(d, struct mdio_device, dev)
| ^~~~~~~~~~~~
./include/linux/phy.h:647:39: note: in expansion of macro ‘to_mdio_device’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
217 | kfree(to_phy_device(dev));
| ^~~~~~~~~~~~~
./include/linux/kernel.h:693:8: note: shadowed declaration is here
693 | void *__mptr = (void *)(ptr); \
| ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
217 | kfree(to_phy_device(dev));
| ^~~~~~~~~~~~~
As they are declared in header files, these warnings are highly
repetitive and very annoying (along with the one from linux/pci.h).
Convert the related macros from linux/{mdio,phy}.h to static inlines
to avoid self-shadowing and potentially improve bug-catching.
No functional changes implied.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210116161246.67075-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing parameter documentation, or fixup wrong parameter names.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the locked variant of the clause 45 mdiobus write accessor -
mdiobus_c45_write().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This header refers to struct reset_control but doesn't include any reset
header. The structure definition is probably somehow indirectly pulled in
since no warnings are reported but for the sake of correctness add the
forward declaration for struct reset_control.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead. Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add set/get drv_data helpers for mdio device.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the existing helpers for the Clause 22 registers add helper
mii_10gbt_stat_mod_linkmode_lpa_t.
Note that this helper is defined in linux/mdio.h, not like the
Clause 22 helpers in linux/mii.h. Reason is that the Clause 45 register
constants are defined in uapi/linux/mdio.h. And uapi/linux/mdio.h
includes linux/mii.h before defining the C45 register constants.
v2:
- remove helpers that don't have users in this series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper linkmode_adv_to_mii_10gbt_adv_t(), similar to
linkmode_adv_to_mii_adv_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation of MDIO bus PM ops doesn't actually implement
bus-specific PM ops but just calls PM ops defined on a device level
what doesn't seem to be fully in line with the core PM model.
When looking e.g. at __device_suspend() the PM core looks for PM ops
of a device in a specific order:
1. device PM domain
2. device type
3. device class
4. device bus
I think it has good reason that there's no PM ops on device level.
Now that a device type representation of PHY's as special type of MDIO
devices was added (only user of MDIO bus PM ops), the MDIO bus
PM ops can be removed including member pm of struct mdio_device.
If for some other type of MDIO device PM ops are needed, it should be
modeled as struct device_type as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As suggested by Rob Herring [1] rename the previously introduced
reset-{,post-}delay-us bindings to the clearer reset-{,de}assert-us
[1] https://patchwork.kernel.org/patch/10104905/
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The module boilerplate macro is named mdio_module_driver and not
module_mdio_driver, fix that.
Fixes: a9049e0c513c ("mdio: Add support for mdio drivers.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a function in mdio for the old ethtool api gset.
We add a new function mdio45_ethtool_ksettings_get for the
new ethtool api glinksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO devices can be stacked upon each other. The current code supports
two levels, which until recently has been enough for a DSA mdio bus on
top of another bus. Now we have hardware which has an MDIO mux in the
middle.
Define an MDIO MUTEX class with three levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are logically MDIO operations, not phy operations, so move them
into the mdio header.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use it or lose it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
|
The helper functions which translate IEEE MDIO Manageable Device (MMD)
Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from
the comparable ethtool supported/advertised settings will be needed by
drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch).
In the same fashion as similar translation functions in linux/mii.h, move
these functions from the PHYLIB core to the linux/mdio.h header file so the
code will not have to be duplicated in each driver needing MMD-to-ethtool
(and vice-versa) translations. The function and some variable names have
been renamed to be more descriptive.
Not tested on the only hardware that currently calls the related functions,
stmmac, because I don't have access to any. Has been compile tested and
the translations have been tested on a locally modified version of e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).
An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.
In the end, this patch also adds the EEE ethtool support implementing:
o phy_ethtool_set_eee
o phy_ethtool_get_eee
v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
values according to ethtool API (thanks to Ben's feedback).
Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
Fixed the phy_init_eee function: we need to check which link mode
was autonegotiated and then the corresponding bits in 7.60 and 7.61
registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes:
/home/davem/src/GIT/net-next/usr/include/linux/mdio.h:271: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
