| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into net-next
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch adds the new CQE SHAMPO fields:
- flush: indicates that we must close the current session and pass the SKB
to the network stack.
- match: indicates that the current packet matches the oppened session,
the packet will be merge into the current SKB.
- header_size: the size of the packet headers that written into the headers
buffer.
- header_entry_index: the entry index in the headers buffer.
- data_offset: packets data offset in the WQE.
Also new cqe handler is added to handle SHAMPO packets:
- The new handler uses CQE SHAMPO fields to build the SKB.
CQE's Flush and match fields are not used in this patch, packets are not
merged in this patch.
Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This commit adds the needed definitions for using the klm_umr_wqe.
UMR stands for user-mode memory registration, is a mechanism to alter
address translation properties of MKEY by posting WorkQueueElement
aka WQE on send queue.
MKEY stands for memory key, MKEY are used to describe a region in memory that
can be later used by HW.
KLM stands for {Key, Length, MemVa}, KLM_MKEY is indirect MKEY that enables
to map multiple memory spaces with different sizes in unified MKEY.
klm_umr_wqe is a UMR that use to update a KLM_MKEY.
SHAMPO feature uses KLM_MKEY for memory registration of his header buffer.
Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This commit adds SHAMPO bit to hca_cap and SHAMPO capabilities structure,
SHAMPO related HW spec hardware fields and enumerations.
SHAMPO stands for: split headers and merge payload offload.
SHAMPO new fields:
WQ:
- headers_mkey: mkey that represents the headers buffer, where the packets
headers will be written by the HW.
- shampo_enable: flag to verify if the WQ supports SHAMPO feature.
- log_reservation_size: the log of the reservation size where the data of
the packet will be written by the HW.
- log_max_num_of_packets_per_reservation: log of the maximum number of
packets that can be written to the same reservation.
- log_headers_entry_size: log of the header entry size of the headers buffer.
- log_headers_buffer_entry_num: log of the entries number of the headers buffer.
RQ:
- shampo_no_match_alignment_granularity: the HW alignment granularity
in case the received packet doesn't match the current session.
- shampo_match_criteria_type: the type of match criteria.
- reservation_timeout: the maximum time that the HW will hold the
reservation.
mlx5_ifc_shampo_cap_bits, the capabilities of the SHAMPO feature:
- shampo_log_max_reservation_size: the maximum allowed value of the field
WQ.log_reservation_size.
- log_reservation_size: the minimum allowed value of the field
WQ.log_reservation_size.
- shampo_min_mss_size: the minimum payload size of packet that can open
a new session or be merged to a session.
- shampo_max_log_headers_entry_size: the maximum allowed value of the field
WQ.log_headers_entry_size
Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Enhance health buffer to include:
- assert_var5: expose the 6'th assert variable.
- time: error's time-stamp in seconds (epoch time).
- rfr: Recovery Flow Requiered. When set, indicates that the error
cannot be recovered without flow involving reset.
- severity: error's severity value, ranging from emergency to debug.
Expose them in the health buffer dump (dmesg and devlink fw reporter).
Health buffer in dmesg:
mlx5_core 0000:08:00.0: print_health_info:425:(pid 912): Health issue observed, firmware internal error, severity(3) ERROR:
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[0] 0x08040700
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[1] 0x00000000
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[2] 0x00000000
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[3] 0x00000000
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[4] 0x00000000
mlx5_core 0000:08:00.0: print_health_info:429:(pid 912): assert_var[5] 0x00000000
mlx5_core 0000:08:00.0: print_health_info:432:(pid 912): assert_exit_ptr 0x00aaf800
mlx5_core 0000:08:00.0: print_health_info:434:(pid 912): assert_callra 0x00aaf70c
mlx5_core 0000:08:00.0: print_health_info:436:(pid 912): fw_ver 16.32.492
mlx5_core 0000:08:00.0: print_health_info:437:(pid 912): time 1634819758
mlx5_core 0000:08:00.0: print_health_info:438:(pid 912): hw_id 0x0000020d
mlx5_core 0000:08:00.0: print_health_info:439:(pid 912): rfr 0
mlx5_core 0000:08:00.0: print_health_info:440:(pid 912): severity 3 (ERROR)
mlx5_core 0000:08:00.0: print_health_info:441:(pid 912): irisc_index 9
mlx5_core 0000:08:00.0: print_health_info:442:(pid 912): synd 0x1: firmware internal error
mlx5_core 0000:08:00.0: print_health_info:444:(pid 912): ext_synd 0x802b
mlx5_core 0000:08:00.0: print_health_info:445:(pid 912): raw fw_ver 0x102001ec
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add new port selection flow steering namespace. Flow steering rules in
this namespaceare are used to determine the physical port for egress
packets.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add needed structures and defines for DTOR (default timeouts register).
This will be used to get timeouts values from FW instead of hard coded
values in the driver code thus enabling support for slower devices which
need longer timeouts.
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add additional flow steering priorities in the RDMA namespace.
This allows adding flow counters to count filtered RDMA traffic and then
continue processing in the regular RDMA steering flow.
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Currently mlx5_core_dev contains array of capabilities. It contains 19
valid capabilities of the device, 2 reserved entries and 12 holes.
Due to this for 14 unused entries, mlx5_core_dev allocates 14 * 8K = 112K
bytes of memory which is never used. Due to this mlx5_core_dev structure
size is 270Kbytes odd. This allocation further aligns to next power of 2
to 512Kbytes.
By skipping non-existent entries,
(a) 112Kbyte is saved,
(b) mlx5_core_dev reduces to 8KB with alignment
(c) 350KB saved in alignment
In future individual capability allocation can be used to skip its
allocation when such capability is disabled at the device level. This
patch prepares mlx5_core_dev to hold capability using a pointer instead
of inline array.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In the current code, the current and maximal capabilities are
maintained in separate arrays which are both per type. In order to
allow the creation of such a basic structure as a dynamically
allocated array, we move curr and max fields to a unified
structure so that specific capabilities can be allocated as one unit.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Fix typo:
*vectores ==> vectors
*realeased ==> released
*erros ==> errors
*namepsace ==> namespace
*trafic ==> traffic
*proccessed ==> processed
*retore ==> restore
*Currenlty ==> Currently
*crated ==> created
*chane ==> change
*cannnot ==> cannot
*usuallly ==> usually
*failes ==> fails
*importent ==> important
*reenabled ==> re-enabled
*alocation ==> allocation
*recived ==> received
*tanslation ==> translation
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add support for HCA caps 2 that contains capabilities for the new
insert/remove header actions.
Added the required definitions for supporting the new reformat type:
added packet reformat parameters, reformat anchors and definitions
to allow copy/set into the inserted EMD (Embedded MetaData) tag.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Striding RQ attributes below are mutually dependent. An unaware
change to one might take the others out of the valid range derived
by the HW caps:
- The MPWQE size in bytes
- The number of strides in a MPWQE
- The stride size
Add checks to verify they are valid and comply to the HW spec
and SW assumptions/requirements.
This is not a fix, no particular issue exists today.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Support matching on ICMPv4/6 type and code parameters using misc3
section of match parameters.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
pull-request: mlx5-next 2021-02-16
The patches in this pr are already submitted and reviewed through the
netdev and rdma mailing lists.
The series includes mlx5 HW bits and definitions for mlx5 real time clock
translation and handling in the mlx5 driver clock module to enable and
support such mode [1]
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210212223042.449816-7-saeed@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add needed structure layouts and defines for MTUTC (Management UTC)
register. MTUTC will be used for cyc2time HW translation.
In addition, add cyc2time modify capability bit and init segment HCA
real time address.
Finally, add capability bits indicating which time-stamping format is
supported per SQ and RQ. Add ts_format in the queue's context layout to
allow configuration.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Introduce mlx5e_trap which includes a dedicated RQ and NAPI for trapped
packets. Trap-RQ processes packets that were destined to be dropped,
but for debug and visibility sake these packets are trapped and reported
to devlink.
Trap-RQ connects between the HW and the driver and is not a part of a
channel. Open mlx5e_create_rq() and mlx5_core_destroy_rq() as API and
add dedicate RQ handlers which report to devlink of trapped packets.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to allow mlx5 core driver to trigger synchronous operations to
its consumers, add a blocking events handler. Add wrappers to
blocking_notifier_[call_chain/chain_register/chain_unregister]. Add trap
callback for action set and notify about this change. Following patches
in the set add a listener for this event.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the hardware interface definitions to query and modify vhca
state, related EQE and event code.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add misc4 match params to enable matching on prog_sample_fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add CQE compression support for completions of packets that span
multiple strides in a Striding RQ, per the HW capability.
In our memory model, we use small strides (256B as of today) for the
non-linear SKB mode. This feature allows CQE compression to work also
for multiple strides packets. In this case decompressing the mini CQE
array will use stride index provided by HW as part of the mini CQE.
Before this feature, compression was possible only for single-strided
packets, i.e. for packets of size up to 256 bytes when in non-linear
mode, and the index was maintained by SW.
This feature is supported for ConnectX-5 and above.
Feature performance test:
This was whitebox-tested, we reduced the PCI speed from 125Gb/s to
62.5Gb/s to overload pci and manipulated mlx5 driver to drop incoming
packets before building the SKB to achieve low cpu utilization.
Outcome is low cpu utilization and bottleneck on pci only.
Test setup:
Server: Intel(R) Xeon(R) Silver 4108 CPU @ 1.80GHz server, 32 cores
NIC: ConnectX-6 DX.
Sender side generates 300 byte packets at full pci bandwidth.
Receiver side configuration:
Single channel, one cpu processing with one ring allocated. Cpu utilization
is ~20% while pci bandwidth is fully utilized.
For the generated traffic and interface MTU of 4500B (to activate the
non-linear SKB mode), packet rate improvement is about 19% from ~17.6Mpps
to ~21Mpps.
Without this feature, counters show no CQE compression blocks for
this setup, while with the feature, counters show ~20.7Mpps compressed CQEs
in ~500K compression blocks.
Signed-off-by: Ofer Levi <oferle@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Up to ConnectX-7 UMR is not used when user passes relaxed ordering access
flag. ConnectX-7 supports setting relaxed ordering read/write mkey
attribute by UMR, indicated by new HCA capabilities.
With ConnectX-7 driver uses UMR when user set relaxed ordering access
flag, in contrast to previous silicon models. Specifically it includes
setting relvant flags of mkey context mask in UMR control segment, and
relaxed ordering write and read flags in UMR mkey context segment.
Link: https://lore.kernel.org/r/20200716105248.1423452-4-leon@kernel.org
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Use generic mlx5 structure defined in mlx5_ifc.h to represent ConnectX
device data structures instead of using structure defined specifically for
mlx5_ib module.
Link: https://lore.kernel.org/r/20200716105248.1423452-3-leon@kernel.org
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Rename mlx5_ifc_device_virtio_emulation_cap_bits to
mlx5_ifc_virtio_emulation_cap_bits to match names produced by the
tools producing these auto generated files.
In addition missing capabilities that will be required by VDPA
implementation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add explicit WQE segment structures for the TLS static and progress
params.
According to the HW spec, TISN is not part of the progress params context,
take it out of it.
Rename the control segment tisn field as it could hold either a TIS or
a TIR number.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add TLS RX offload related IFC hardware fields and enumerations.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add needed structure layouts and defines for pci sync for fw update
event. The downstream patches will include event handlers for this event
type.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The imm_inval_pkey field can hold four different types of data,
depends on the usage, the data could be one of the below:
- Immediate field of the received message
- Invalidate rkey
- Pkey of the packet
- Flow table metadata
Current implementation doesn't reflect the intended usage of the
field at usage time.
Reflect the different types by replace this field with a union,
modify code where this field is used to reflect its intended
usage.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add IPsec offload related IFC structs, layouts and enumerations.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add new RDMA TX flow steering namespace. Flow steering rules in
this namespace are used to filter transmitted RDMA traffic.
Link: https://lore.kernel.org/r/20200324061425.1570190-2-leon@kernel.org
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
On load, Driver caches MCAM (Management Capabilities Mask Register)
registers. in addition to the only MCAM register group (0) the driver
already reads, here we add support for reading groups 1 and 2.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose vDPA emulation device capabilities from the core layer.
It includes reading the capabilities from the firmware and exposing
helper functions to access the data.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Shahaf Shuler <shahafs@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Pull RDMA subsystem updates from Jason Gunthorpe:
"This cycle mainly saw lots of bug fixes and clean up code across the
core code and several drivers, few new functional changes were made.
- Many cleanup and bug fixes for hns
- Various small bug fixes and cleanups in hfi1, mlx5, usnic, qed,
bnxt_re, efa
- Share the query_port code between all the iWarp drivers
- General rework and cleanup of the ODP MR umem code to fit better
with the mmu notifier get/put scheme
- Support rdma netlink in non init_net name spaces
- mlx5 support for XRC devx and DC ODP"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
RDMA: Fix double-free in srq creation error flow
RDMA/efa: Fix incorrect error print
IB/mlx5: Free mpi in mp_slave mode
IB/mlx5: Use the original address for the page during free_pages
RDMA/bnxt_re: Fix spelling mistake "missin_resp" -> "missing_resp"
RDMA/hns: Package operations of rq inline buffer into separate functions
RDMA/hns: Optimize cmd init and mode selection for hip08
IB/hfi1: Define variables as unsigned long to fix KASAN warning
IB/{rdmavt, hfi1, qib}: Add a counter for credit waits
IB/hfi1: Add traces for TID RDMA READ
RDMA/siw: Relax from kmap_atomic() use in TX path
IB/iser: Support up to 16MB data transfer in a single command
RDMA/siw: Fix page address mapping in TX path
RDMA: Fix goto target to release the allocated memory
RDMA/usnic: Avoid overly large buffers on stack
RDMA/odp: Add missing cast for 32 bit
RDMA/hns: Use devm_platform_ioremap_resource() to simplify code
Documentation/infiniband: update name of some functions
RDMA/cma: Fix false error message
RDMA/hns: Fix wrong assignment of qp_access_flags
...
|
|
To resolve dependencies in following patches
mlx5_ib.h conflict resolved by keeing both hunks
Linux 5.3-rc8
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
counters
Map capability bit indicating that HCA supports port buffer's congestion
counters. Also map registers with the corresponding counters.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Merge mlx5-next patches needed for upcoming mlx5 software steering.
1) Alex adds HW bits and definitions required for SW steering
2) Ariel moves device memory management to mlx5_core (From mlx5_ib)
3) Maor, Cleanups and fixups for eswitch mode and RoCE
4) Mark, Set only stag for match untagged packets
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the required Software Steering hardware definitions and
bits to mlx5_ifc.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Klitenik <kliten@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add two events that were defined in the device specification but were
not exposed in the driver list.
Post this patch those events can be read over the DEVX events interface
once be reported by the firmware.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Edward Srouji <edwards@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190808084358.29517-4-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Fix the used constants for TLS TIS opmods, per the HW specification.
Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Misc updates from mlx5-next branch:
1) Add the required HW definitions and structures for upcoming TLS
support.
2) Add support for MCQI and MCQS hardware registers for fw version query.
3) Added hardware bits and structures definitions for sub-functions
4) Small code cleanup and improvement for PF pci driver.
5) Bluefield (ECPF) updates and refactoring for better E-Switch
management on ECPF embedded CPU NIC:
5.1) Consolidate querying eswitch number of VFs
5.2) Register event handler at the correct E-Switch init stage
5.3) Setup PF's inline mode and vlan pop when the ECPF is the
E-Swtich manager ( the host PF is basically a VF ).
5.4) Handle Vport UC address changes in switchdev mode.
6) Cleanup the rep and netdev reference when unloading IB rep.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
i# All conflicts fixed but you are still merging.
|
|
Add TLS offload related IFC structs, layouts and enumerations.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use the reported device capabilities for the supported user events (i.e.
affiliated and un-affiliated) to set the EQ mask.
As the event mask can be up to 256 defined by 4 entries of u64 change
the applicable code to work accordingly.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To support sriov on a E-Switch manager, num_vfs are queried
to the firmware whenever E-Switch manager is notified by
esw_functions_changed event.
Replace host_params event with esw_functions_changed event that reflects
more appropriate naming.
While at it, also correct num_vfs type from int to u16 as expected by
the function mlx5_esw_query_functions().
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Handle event of power state change in the PCIE slot. When the event
occurs, check if query power state and PCI power fields is supported. If
so, read these fields from MPEIN (management PCIE info) register and
issue a corresponding message.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
