| Age | Commit message (Collapse) | Author |
|---|
|
RTL8723DS comes in two variant and each of them has their own SDIO ID:
- 0xd723 can connect two antennas. The WiFi part is still 1x1 so the
second antenna can be dedicated to Bluetooth
- 0xd724 can only connect one antenna so it's shared between WiFi and
Bluetooth
Add a new entry for the single antenna RTL8723DS (0xd724) which can be
found on the MangoPi MQ-Quad. Also rename the existing RTL8723DS entry
(0xd723) so it's name reflects that it's the variant with support for
two antennas.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-4-martin.blumenstingl@googlemail.com
|
|
Add SDIO ids for use with the muRata 1YN (Cypress CYW43439).
The odd thing about this is that the previous 1YN populated
on M.2 card for evaluation purposes had BRCM SDIO vendor ID,
while the chip populated on real hardware has a Cypress one.
The device ID also differs between the two devices. But they
are both 43439 otherwise, so add the IDs for both.
On-device 1YN (43439), the new one, chip label reads "1YN":
```
/sys/.../mmc_host/mmc2/mmc2:0001 # cat vendor device
0x04b4
0xbd3d
```
EA M.2 evaluation board 1YN (43439), the old one, chip label reads "1YN ES1.4":
```
/sys/.../mmc_host/mmc0/mmc0:0001/# cat vendor device
0x02d0
0xa9a6
```
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230407203752.128539-1-marex@denx.de
|
|
Add the SDIO vendor ID for Realtek and some device IDs extracted from
their GPL vendor driver. This will be useful in the future when the
rtw88 driver gains support for these chips.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-7-martin.blumenstingl@googlemail.com
|
|
The Marvell SD8978 (aka NXP IW416) uses identical registers as SD8987,
so reuse the existing mwifiex_reg_sd8987 definition.
Note that mwifiex_reg_sd8977 and mwifiex_reg_sd8997 are likewise
identical, save for the fw_dump_ctrl register: They define it as 0xf0
whereas mwifiex_reg_sd8987 defines it as 0xf9. I've verified that
0xf9 is the correct value on SD8978. NXP's out-of-tree driver uses
0xf9 for all of them, so there's a chance that 0xf0 is not correct
in the mwifiex_reg_sd8977 and mwifiex_reg_sd8997 definitions. I cannot
test that for lack of hardware, hence am leaving it as is.
NXP has only released a firmware which runs Bluetooth over UART.
Perhaps Bluetooth over SDIO is unsupported by this chipset.
Consequently, only an "sdiouart" firmware image is referenced, not an
alternative "sdsd" image.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de
|
|
Add HW and SDIO ids for use with the muRata 1YN (Cypress CYW43439).
Add the firmware mapping structures for the CYW43439 chipset.
The 43439 needs some things setup similar to the 43430 chipset.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220827024903.617294-1-marex@denx.de
|
|
The MT7961 SDIO identifier for MediaTek Bluetooth devices were being
referred in the MediaTek Bluetooth driver.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add HW and SDIO ids for use with the SparkLan AP6275S
Add the firmware mapping structures for the BRCM43752 chipset.
The 43752 needs some things setup similar to the 43012 chipset.
The WATERMARK shows better performance when initialized to the 4373 value.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812165218.2508258-2-angus@akkea.ca
|
|
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
|
|
Moved macros used for Vendor/Device ID from wilc1000 driver to common
header file and changed macro name for consistency with other macros.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717051134.19160-1-ajay.kathat@microchip.com
|
|
Define appropriate macro names for consistency with other macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200629072144.24351-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix ordering of SDIO IDs to conform to the comment above, which says vendor
first, device next.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-12-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Define appropriate macro names for consistency with other macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-10-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Check for "AR6003 or later" is slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath6kl.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-8-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Define appropriate macro names for consistency with other Siano macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-7-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Define appropriate macro names for consistency with other macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200522144412.19712-6-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
|
|
Define appropriate macro names for consistency with other Marvell macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-5-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
|
|
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
|
|
Add underscore as separator in Marvell 8688 macro names for better
readability and consistency.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-3-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
|
|
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
BCM4359 is a 2x2 802.11 abgn+ac Dual-Band HT80 combo chip and it
supports Real Simultaneous Dual Band feature.
Based on a similar patch by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
v4.11-rc1 did introduce a patch series that rearranged the
sdio quirks into a header file. Unfortunately this did forget
to handle SDIO_VENDOR_ID_TI differently between wl1251 and
wl1271 with the result that although the wl1251 was found on
the sdio bus, the firmware did not load any more and there was
no interface registration.
This patch defines separate constants to be used by sdio quirks
and drivers.
Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDIO identifier for MediaTek Bluetooth devices were defined in the
MediaTek Bluetooth driver. Moving the definitions in MMC header file
seems common sense.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
|
|
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
|
|
Consolidate all the sdio devices' IDs into sdio_ids.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
BCM43455 is a more recent revision of the BCM4345. Some of the BCM43455
got a dedicated SDIO device ID which is currently not supported by
brcmfmac.
Adding the new sdio_device_id to brcmfmac is enough to get the BCM43455
supported because the chip itself is already supported (due to BCM4345
support in the driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: Steve deRosier <derosier@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds support for the 4356-sdio wireless chip.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These changes add support for BCM4345 SDIO chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Syed Asifful Dayyan <syedd@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for the bcm43340 and bcm43341 wireless
chipsets. These two chipsets are identical from wireless parts
perspective. As such they use the same firmware image.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rob Herring <rob.herring@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
[arend@broadcom.com: squash to single commit, remove 43341 chipid]
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The SDIO identifier for Broadcom WLAN devices were defined in the
brcmfmac SDIO driver. Moving the definitions in MMC header file
seems common sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Different sdio device IDs are designated to support different intel
wimax silicon sku. The new macro SDIO_DEVICE_ID_IWMC3200_WIMAX_2G5(0x1407)
is added to support iwmc3200 2.5GHz sku. The existing
SDIO_DEVICE_ID_IWMC3200_WIMAX(0x1402) is for iwmc3200 general sku.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
receivers
sdio: add cards id for sms (Siano Mobile Silicon) MDTV receivers
Add SDIO vendor ID, and multiple device IDs for
various SMS-based MDTV SDIO adapters.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add driver for Marvell's Libertas 8385 and 8686 wifi chips.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Dan Williams <dcbw@redhat.com>
|
|
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
