| Age | Commit message (Collapse) | Author |
|---|
|
Add a supported_interfaces member to phylib so we know which
interfaces a PHY supports. Currently, set any unconverted driver
to indicate all interfaces are supported.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Provide phy driver start/stop hooks so that the PHY driver knows when
the network driver is starting or stopping. This will be used for the
Marvell 10G driver so that we can sanely refuse to start if the PHYs
firmware is not present, and also so that we can sanely support SFPs
behind the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow phylib drivers to pass the hardware-resolved pause state to MAC
drivers, rather than using the software-based pause resolution code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a method to query the PHY's in-band capabilities for a PHY
interface mode. This can be used to determine for the specified
interface mode whether in-band signalling is supported, and whether
the PHY requires in-band signalling.
When not implemented, or the PHY driver doesn't report any modes
for the interface, LINK_INBAND_VALID will not be set. When set, the
remainder of the flags can be interpreted.
LINK_INBAND_POSSIBLE means that the device can be configured to use
or not use in-band signalling. Later patches may add support to
configure this at the PHY.
LINK_INBAND_REQUIRED means that the device uses in-band signalling
which can not be disabled.
When only LINK_INBAND_VALID has been set, this means that the device
does not support any in-band signalling, and can't be configured to
do so.
"Bypass" mode (where the device may be configured for in-band, but
may still bring the link up if there is no in-band received from the
link partner) is not considered in this patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Device driver structures are shared between all devices that they
match, and thus nothing should never write to the device driver
structure through the phydev->drv pointer. Let's make this pointer
const to catch code that attempts to do so.
Suggested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 32bb4515e34469975abc936deb0a116c4a445817.
This reverts commit d078d480639a4f3b5fc2d56247afa38e0956483a.
This reverts commit fcc4b105caa4b844bf043375bf799c20a9c99db1.
This reverts commit 345237dbc1bdbb274c9fb9ec38976261ff4a40b8.
This reverts commit 7db69ec9cfb8b4ab50420262631fb2d1908b25bf.
This reverts commit 95132a018f00f5dad38bdcfd4180d1af955d46f6.
This reverts commit 63d5eaf35ac36cad00cfb3809d794ef0078c822b.
This reverts commit c29451aefcb42359905d18678de38e52eccb3bb5.
This reverts commit 2ab0edb505faa9ac90dee1732571390f074e8113.
This reverts commit dedd702a35793ab462fce4c737eeba0badf9718e.
This reverts commit 034fcc210349b873ece7356905be5c6ca11eef2a.
This reverts commit 9c5625f559ad6fe9f6f733c11475bf470e637d34.
This reverts commit 02018c544ef113e980a2349eba89003d6f399d22.
Looks like we need more time for reviews, and incremental
changes will be hard to make sense of. So revert.
Link: https://lore.kernel.org/all/ZZP6FV5sXEf+xd58@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit cff9c565e65f3622e8dc1dcc21c1520a083dff35.
Revert based on feedback from Russell.
Link: https://lore.kernel.org/all/ZZPtUIRerqTI2%2Fyh@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the @phy_timer: line to prevent the kernel-doc warning:
include/linux/phy.h:768: warning: Excess struct member 'phy_timer' description in 'phy_device'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: netdev@vger.kernel.org
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __of_mdiobus_register() function was storing the device node in
dev.of_node without increasing its reference count. It implicitly relied
on the caller to maintain the allocated node until the mdiobus was
unregistered.
Now, __of_mdiobus_register() will acquire the node before assigning it,
and of_mdiobus_unregister_callback() will be called at the end of
mdio_unregister().
Drivers can now release the node immediately after MDIO registration.
Some of them are already doing that even before this patch.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHY in PHY package may require to read/write MMD regs to correctly
configure the PHY package.
Add support for these additional required function in both lock and no
lock variant.
It's assumed that the entire PHY package is either C22 or C45. We use
C22 or C45 way of writing/reading to mmd regs based on the passed phydev
whether it's C22 or C45.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current API for PHY package are limited to single address to configure
global settings for the PHY package.
It was found that some PHY package (for example the qca807x, a PHY
package that is shipped with a bundle of 5 PHY) requires multiple PHY
address to configure global settings. An example scenario is a PHY that
have a dedicated PHY for PSGMII/serdes calibrarion and have a specific
PHY in the package where the global PHY mode is set and affects every
other PHY in the package.
Change the API in the following way:
- Change phy_package_join() to take the base addr of the PHY package
instead of the global PHY addr.
- Make __/phy_package_write/read() require an additional arg that
select what global PHY address to use by passing the offset from the
base addr passed on phy_package_join().
Each user of this API is updated to follow this new implementation
following a pattern where an enum is defined to declare the offset of the
addr.
We also drop the check if shared is defined as any user of the
phy_package_read/write is expected to use phy_package_join first. Misuse
of this will correctly trigger a kernel panic for NULL pointer
exception.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch addr type in phy_package_shared struct to u8.
The value is already checked to be non negative and to be less than
PHY_MAX_ADDR, hence u8 is better suited than using int.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move part of the genphy_c45_pma_read_abilities() code to a separate
function.
Some PHYs do not implement PMA/PMD status 2 register (Register 1.8) but
do implement PMA/PMD extended ability register (Register 1.11). To make
use of it, we need to be able to access this part of code separately.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a possible_interfaces member to struct phy_device to indicate which
interfaces a clause 45 PHY may switch between depending on the media.
This must be populated by the PHY driver by the time the .config_init()
method completes according to the PHYs host-side configuration.
For example, the Marvell 88x3310 PHY can switch between 10GBASE-R,
5GBASE-R, 2500BASE-X, and SGMII on the host side depending on the media
side speed, so all these interface modes are set in the
possible_interfaces member.
This allows phylib users (such as phylink) to know in advance which
interface modes to expect, which allows them to appropriately restrict
the advertised link modes according to the capabilities of other parts
of the link.
Tested-by: Luo Jie <quic_luoj@quicinc.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1r6VHk-00DDLN-I7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revert following commits:
commit acec05fb78ab ("net_tstamp: Add TIMESTAMPING SOFTWARE and HARDWARE mask")
commit 11d55be06df0 ("net: ethtool: Add a command to expose current time stamping layer")
commit bb8645b00ced ("netlink: specs: Introduce new netlink command to get current timestamp")
commit d905f9c75329 ("net: ethtool: Add a command to list available time stamping layers")
commit aed5004ee7a0 ("netlink: specs: Introduce new netlink command to list available time stamping layers")
commit 51bdf3165f01 ("net: Replace hwtstamp_source by timestamping layer")
commit 0f7f463d4821 ("net: Change the API of PHY default timestamp to MAC")
commit 091fab122869 ("net: ethtool: ts: Update GET_TS to reply the current selected timestamp")
commit 152c75e1d002 ("net: ethtool: ts: Let the active time stamping layer be selectable")
commit ee60ea6be0d3 ("netlink: specs: Introduce time stamping set command")
They need more time for reviews.
Link: https://lore.kernel.org/all/20231118183529.6e67100c@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility I
introduce a default_timestamp flag in phy_device that is set by the phy
driver to know we are using the old API behavior.
The phy_set_timestamp function is called at each call of phy_attach_direct.
In case of MAC driver using phylink this function is called when the
interface is turned up. Then if the interface goes down and up again the
last choice of timestamp will be overwritten by the default choice.
A solution could be to cache the timestamp status but it can bring other
issues. In case of SFP, if we change the module, it doesn't make sense to
blindly re-set the timestamp back to PHY, if the new module has a PHY with
mediocre timestamping capabilities.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHYs hwtstamp callback are still getting the timestamp config from
ifreq and using copy_from/to_user.
Get rid of these functions by using timestamp configuration in parameter.
This also allow to move on to kernel_hwtstamp_config and be similar to
net devices using the new ndo_hwstamp_get/set.
This adds the possibility to manipulate the timestamp configuration
from the kernel which was not possible with the copy_from/to_user.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6:cd:11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0a9 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The PSGMII interface is similar to QSGMII. The main difference
is that the PSGMII interface combines five SGMII lines into a
single link while in QSGMII only four lines are combined.
Similarly to the QSGMII, this interface mode might also needs
special handling within the MAC driver.
It is commonly used by Qualcomm with their QCA807x PHY series and
modern WiSoC-s.
Add definitions for the PHY layer to allow to express this type
of connection between the MAC and PHY.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux LEDs can be requested to perform hardware accelerated blinking
to indicate link, RX, TX etc. Pass the rules for blinking to the PHY
driver, if it implements the ops needed to determine if a given
pattern can be offloaded, to offload it, and what the current offload
is. Additionally implement the op needed to get what device the LED is
for.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-3-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1e2dc14509fd ("net: ethtool: Add helpers for reporting test results")
declared but never implemented these function.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230808144610.19096-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net/core/dev_ioctl.c (built-in code) will want to call phy_mii_ioctl()
for hardware timestamping purposes. This is not directly possible,
because phy_mii_ioctl() is a symbol provided under CONFIG_PHYLIB.
Do something similar to what was done in DSA in commit 5a17818682cf
("net: dsa: replace NETDEV_PRE_CHANGE_HWTSTAMP notifier with a stub"),
and arrange some indirect calls to phy_mii_ioctl() through a stub
structure containing function pointers, that's provided by phylib as
built-in even when CONFIG_PHYLIB=m, and which phy_init() populates at
runtime (module insertion).
Note: maybe the ownership of the ethtool_phy_ops singleton is backwards,
and the methods exposed by that should be later merged into phylib_stubs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a separate function to read the BASE-T1 abilities. Some PHYs do not
indicate the availability of the extended BASE-T1 ability register, so
this function must be called separately.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Dan Carpenter reported a signedness bug in genphy_loopback(). Andrew
reports that:
"It is common to get this wrong in general with PHY drivers. Dan
regularly posts fixes like this soon after a PHY driver patch it
merged. I really wish we could somehow get the compiler to warn when
the result from phy_read() is stored into a unsigned type. It would
save Dan a lot of work."
Let's make phy_read*_poll_timeout() immune to further issues when "val"
is an unsigned type by storing the read function's result in a signed
int as well as "val", and using the signed variable both to check for
an error and for propagating that error to the caller.
The advantage of this method is we don't change where the cast from
the signed return code to the user's variable occurs - so users will
see no change.
Previously Heiner changed phy_read_poll_timeout() to check for an error
before evaluating the user supplied condition, but didn't update
phy_read_mmd_poll_timeout(). Make that change there too.
Link: https://lore.kernel.org/r/d7bb312e-2428-45f6-b9b3-59ba544e8b94@kili.mountain
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q4kX6-00BNuM-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When taking a network interface down (or removing a SFP module) after
the PHY has encountered an error, phy_stop() complains incorrectly
that it was called from HALTED state.
The reason this is incorrect is that the network driver will have
called phy_start() when the interface was brought up, and the fact
that the PHY has a problem bears no relationship to the administrative
state of the interface. Taking the interface administratively down
(which calls phy_stop()) is always the right thing to do after a
successful phy_start() call, whether or not the PHY has encountered
an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98cafc ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mdio_bus_init() is either used as a local module_init() entry,
or it gets called in phy_device.c. In the former case, there
is no declaration, which causes a warning:
drivers/net/phy/mdio_bus.c:1371:12: error: no previous prototype for 'mdio_bus_init' [-Werror=missing-prototypes]
Remove the #ifdef around the declaration to avoid the warning..
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516194625.549249-4-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().
This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.
In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.
If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fwnode_get_phy_node() does not motify the fwnode structure, so make
the argument const,
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cond sometimes is (val & MASK) what may result in a false positive
if val is a negative errno. We shouldn't evaluate cond if val < 0.
This has no functional impact here, but it's not nice.
Therefore switch order of the checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/6d8274ac-4344-23b4-d9a3-cad4c39517d4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With following patches:
commit 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
commit 5827b168125d ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
we set the advertisement to potentially supported values. This behavior
may introduce new regressions on systems where EEE was disabled by
default (BIOS or boot loader configuration or by other ways.)
At same time, with this patches, we would overwrite EEE advertisement
configuration made over ethtool.
To avoid this issues, we need to cache initial and ethtool advertisement
configuration and store it for later use.
Fixes: 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Fixes: 5827b168125d ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
Fixes: 022c3f87f88e ("net: phy: add genphy_c45_ethtool_get/set_eee() support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add new genphy_c45_an_config_eee_aneg() function and replace some of
genphy_c45_write_eee_adv() calls. This will be needed by the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add replacement for phy_ethtool_get/set_eee() functions.
Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
specification beyond Clause 22. The better place for this code is
phy-c45.c
- currently it is able to do read/write operations on PHYs with
different abilities to not existing registers. It is better to
use stored supported_eee abilities to avoid false read/write
operations.
- the eee_active detection will provide wrong results on not supported
link modes. It is better to validate speed/duplex properties against
supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
EEE link modes...
By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
(Register 1.2295)
Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.
Results of EEE ability detection will be stored into new variable
phydev->supported_eee.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some C22 PHYs do bad things when there are C45 transactions on the
bus. In order to handle this, the bus needs to be scanned first for
C22 at all addresses, and then C45 scanned for all addresses.
The Marvell pxa168 driver scans a specific address on the bus to find
its PHY. This is a C22 only device, so update it to use the c22
helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring the PLCA Reconciliation Sublayer on
multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g.,
10BASE-T1S). This patch adds the appropriate netlink interface
to ethtool.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently C22 and C45 transactions are mixed over a combined API calls
which make use of a special bit in the reg address to indicate if a
C45 transaction should be performed. This makes it impossible to know
if the bus driver actually supports C45. Additionally, many C22 only
drivers don't return -EOPNOTSUPP when asked to perform a C45
transaction, they mistaking perform a C22 transaction.
This is the first step to cleanly separate C22 from C45. To maintain
backwards compatibility until all drivers which are capable of
performing C45 are converted to this new API, the helper functions
will fall back to the older API if the new API is not
supported. Eventually this fallback will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
