| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull a few more MIPS updates from Paul Burton:
"Some SGI IP27 specific PCI rework and a batch of fixes:
- A build fix for BMIPS5000 configurations with
CONFIG_HW_PERF_EVENTS=y, which also neatly removes some #ifdefery.
- A fix to report supported ISAs correctly on older Ingenic SoCs
which incorrectly indicate MIPSr2 support in their cop0 Config
register.
- Some PCI modernization for SGI IP27 systems as part of ongoing work
to support some other SGI systems.
- A fix allowing use of appended DTB files with generic kernels.
- DMA mask fixes for SGI IP22 & Alchemy systems"
* tag 'mips_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Alchemy: add DMA masks for on-chip ethernet
MIPS: SGI-IP22: provide missing dma_mask/coherent_dma_mask
generic: fix appended dtb support
MIPS: SGI-IP27: abstract chipset irq from bridge
MIPS: SGI-IP27: use generic PCI driver
MIPS: Fix Ingenic SoCs sometimes reporting wrong ISA
MIPS: perf: Fix build with CONFIG_CPU_BMIPS5000 enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Fix-ups:
- Remove unused BACKLIGHT_LCD_SUPPORT symbol
- Remove unused BACKLIGHT_CLASS_DEVICE dependencies
- Add DT support to lm3630a_bl
Bug Fixes:
- Fix error path issues in lm3630a_bl"
* tag 'backlight-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: lm3630a: Add firmware node support
dt-bindings: backlight: Add lm3630a bindings
backlight: lm3630a: Return 0 on success in update_status functions
video: lcd: Remove useless BACKLIGHT_CLASS_DEVICE dependencies
video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel symbol
|
|
Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Add EC host command support using rpmsg
- Add new CrOS USB PD logging driver
- Transfer spi messages at high priority
- Add support to trace CrOS EC commands
- Minor fixes and cleanups in protocol and debugfs
Wilco EC:
- Standardize Wilco EC mailbox interface
- Add h1_gpio status to debugfs"
* tag 'tag-chrome-platform-for-v5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_proto: Add trace event to trace EC commands
platform/chrome: cros_ec_debugfs: Use cros_ec_cmd_xfer_status helper
platform/chrome: cros_ec: Add EC host command support using rpmsg
platform/chrome: wilco_ec: Add h1_gpio status to debugfs
platform/chrome: wilco_ec: Standardize mailbox interface
platform/chrome: cros_ec_proto: check for NULL transfer function
platform/chrome: Add CrOS USB PD logging driver
platform/chrome: cros_ec_spi: Transfer messages at high priority
platform/chrome: cros_ec_debugfs: no need to check return value of debugfs_create functions
platform/chrome: cros_ec_debugfs: Remove dev_warn when console log is not supported
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
"Gathered pile of patches for Platform Drivers x86. No surprises and no
merge conflicts. Business as usual.
Summary:
- New driver of power button for Basin Cove PMIC.
- ASUS WMI driver has got a Fn lock mode switch support.
- Resolve a never end story with non working Wi-Fi on newer Lenovo
Ideapad computers. Now the black list is replaced with white list.
- New facility to debug S0ix failures on Intel Atom platforms. The
Intel PMC and accompanying drivers are cleaned up.
- Mellanox got a new TmFifo driver. Besides tachometer sensor and
watchdog are enabled on Mellanox platforms.
- The information of embedded controller is now recognized on new
Thinkpads. Bluetooth driver on Thinkpads is blacklisted for some
models.
- Touchscreen DMI driver extended to support 'jumper ezpad 6 pro b'
and Myria MY8307 2-in-1.
- Additionally few small fixes here and there for WMI and ACPI laptop
drivers.
- The following is an automated git shortlog grouped by driver:
- alienware-wmi:
- printing the wrong error code
- fix kfree on potentially uninitialized pointer
- asus-wmi:
- Add fn-lock mode switch support
- dell-laptop:
- fix rfkill functionality
- dell-rbtn:
- Add missing #include
- ideapad-laptop:
- Remove no_hw_rfkill_list
- intel_pmc_core:
- Allow to dump debug registers on S0ix failure
- Convert to a platform_driver
- Mark local function static
- intel_pmc_ipc:
- Don't map non-used optional resources
- Apply same width for offset definitions
- Use BIT() macro
- adding error handling
- intel_punit_ipc:
- Revert "Fix resource ioremap warning"
- mlx-platform:
- Add mlx-wdt platform driver activation
- Add support for tachometer speed register
- Add TmFifo driver for Mellanox BlueField Soc
- sony-laptop:
- Fix unintentional fall-through
- thinkpad_acpi:
- cleanup for Thinkpad ACPI led
- Mark expected switch fall-throughs
- fix spelling mistake "capabilites" -> "capabilities"
- Read EC information on newer models
- Disable Bluetooth for some machines
- touchscreen_dmi:
- Add info for 'jumper ezpad 6 pro b' touchscreen
- Add info for Myria MY8307 2-in-1"
* tag 'platform-drivers-x86-v5.2-1' of git://git.infradead.org/linux-platform-drivers-x86: (26 commits)
platform/x86: Add support for Basin Cove power button
platform/x86: asus-wmi: Add fn-lock mode switch support
platform/x86: ideapad-laptop: Remove no_hw_rfkill_list
platform/x86: touchscreen_dmi: Add info for 'jumper ezpad 6 pro b' touchscreen
platform/x86: thinkpad_acpi: cleanup for Thinkpad ACPI led
platform/x86: thinkpad_acpi: Mark expected switch fall-throughs
platform/x86: sony-laptop: Fix unintentional fall-through
platform/x86: alienware-wmi: printing the wrong error code
platform/x86: intel_pmc_core: Allow to dump debug registers on S0ix failure
platform/x86: intel_pmc_core: Convert to a platform_driver
platform/x86: mlx-platform: Add mlx-wdt platform driver activation
platform/x86: mlx-platform: Add support for tachometer speed register
platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc
platform/x86: thinkpad_acpi: fix spelling mistake "capabilites" -> "capabilities"
platform/x86: intel_punit_ipc: Revert "Fix resource ioremap warning"
platform/x86: intel_pmc_ipc: Don't map non-used optional resources
platform/x86: intel_pmc_ipc: Apply same width for offset definitions
platform/x86: intel_pmc_ipc: Use BIT() macro
platform/x86: alienware-wmi: fix kfree on potentially uninitialized pointer
platform/x86: dell-laptop: fix rfkill functionality
...
|
|
Converted bridge code to a platform driver using the PCI generic driver
framework and use adding platform devices during xtalk scan. This allows
easier sharing bridge driver for other SGI platforms like IP30 (Octane) and
IP35 (Origin 3k, Fuel, Tezro).
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
[paul.burton@mips.com:
- Leave __phys_to_dma(), __dma_to_phys() & pcibus_to_node() in
arch/mips/pci/pci-ip27.c since the motivation for moving them
disappeared when the driver stopped being moved to drivers/pci.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- API for late atomic transfers (e.g. to shut down via PMIC). We have a
seperate callback now which is called under clearly defined
conditions. In-kernel users are converted, too.
- new driver for the AMD PCIe MP2 I2C controller
- large refactoring for at91 and bcm-iproc (both gain slave support due
to this)
- and a good share of various driver improvements anf fixes
* 'i2c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (57 commits)
dt-bindings: i2c: riic: document r7s9210 support
i2c: imx-lpi2c: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
i2c-piix4: Add Hygon Dhyana SMBus support
i2c: core: apply 'is_suspended' check for SMBus, too
i2c: core: ratelimit 'transfer when suspended' errors
i2c: iproc: Change driver to use 'BIT' macro
i2c: riic: Add Runtime PM support
i2c: mux: demux-pinctrl: use struct_size() in devm_kzalloc()
i2c: mux: pca954x: allow management of device idle state via sysfs
i2c: mux: pca9541: remove support for unused platform data
i2c: mux: pca954x: remove support for unused platform data
dt-bindings: i2c: i2c-mtk: add support for MT8516
i2c: axxia: use auto cmd for last message
i2c: gpio: flag atomic capability if possible
i2c: algo: bit: add flag to whitelist atomic transfers
i2c: stu300: use xfer_atomic callback to bail out early
i2c: ocores: enable atomic xfers
i2c: ocores: refactor setup for polling
i2c: tegra-bpmp: convert to use new atomic callbacks
i2c: omap: Add the master_xfer_atomic hook
...
|
|
Some of latest ASUS laptops support new fn-lock mode switching.
This commit detect whether if the fn-lock option is enabled in
BIOS setting, and toggle the fn-lock mode via a new WMI DEVID
0x00100023 when the corresponding notify code captured.
The ASUS fn-lock mode switch is activated by pressing Fn+Esc.
When on, keys F1 to F12 behave as applicable, with meanings
defined by the application being used at the time. When off,
F1 to F12 directly triggers hardware features, well known audio
volume up/down, brightness up/down...etc, which were triggered
by holding down Fn key and F-keys.
Because there's no way to retrieve the fn-lock mode via existing
WMI methods per ASUS spec, driver need to initialize and keep the
fn-lock mode by itself.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"One small feature was added this release but the bulk of the diffstat
and the changelog comes from the fact that several older drivers got
some fairly hefty reworks and a couple of new drivers were added:
- Support for detailed control of timing around chip selects from
Sowjanya Komatineni.
- A big set of fixes and imrovements for the Tegra114 driver from
Sowjanya Komatineni.
- A big simplification of the GPIO driver from Andrey Smirnov.
- DMA support and fixes for the Freescale LPSPI driver from Clark
Wang.
- Fixes and optimizations for the bcm2835aux from Martin Sparl.
- New drivers for Mediatek MT7621 (graduated from staging) and Zynq
QSPI"
[ This is a so-called "evil merge" that additionally removes a warning
due to an unused variable 'i' introduced by commit 1dfbf334f123 ("spi:
ep93xx: Convert to use CS GPIO descriptors") - Linus ]
* tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (127 commits)
spi: rspi: Fix handling of QSPI code when transmit and receive
spi: atmel-quadspi: fix crash while suspending
spi: stm32: return the get_irq error
spi: tegra114: fix PIO transfer
spi: pxa2xx: fix SCR (divisor) calculation
spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select
spi: ep93xx: Convert to use CS GPIO descriptors
spi: AD ASoC: declare missing of table
spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl
spi: stm32-qspi: manage the get_irq error case
spi/spi-bcm2835: Split transfers that exceed DLEN
spi: expand mode support
dt-bindings: spi: spi-mt65xx: add support for MT8516
spi: pxa2xx: Add support for Intel Comet Lake
spi/trace: Cap buffer contents at 64 bytes
spi: Release spi_res after finalizing message
spi: Remove warning in spi_split_transfers_maxsize()
spi: Remove one needless transfer speed fall back case
spi: sh-msiof: Document r8a77470 bindings
spi: pxa2xx: use a module softdep for dw_dmac
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add driver for Intersil ISL68137 PWM Controller
- Add driver for Lochnagar 2
- Add driver for Infineon IR38064 Voltage Regulator
- Add support for TMP75B to lm75 driver
- Convert documentation to ReST format
- Use request_muxed_region for Super-IO accesses in several drivers
- Add 'samples' attribute to ABI, and start using it
- Add support for custom sysfs attributes to pmbus drivers (used in
ISL68137 driver)
- Introduce HWMON_CHANNEL_INFO macro
- Automated changes:
- Use permission specific [SENSOR_][DEVICE_]ATTR variants
- Fix build warnings due to unused of_device_id structures
- Use HWMON_CHANNEL_INFO macro
- Various minor improvements and fixes
* tag 'hwmon-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (125 commits)
hwmon: (lm75) Add support for TMP75B
dt-bindings: hwmon: Add tmp75b to lm75.txt
hwmon: (s3c) Use dev_get_drvdata()
hwmon: (max6650) Drop call to thermal_cdev_update
docs: hwmon: remove the extension from .rst files
docs: hwmon: convert three docs to ReST format
hwmon: (max6650) add thermal cooling device capability
hwmon: (ina3221) Add voltage conversion time settings
hwmon: (ina3221) Do not read-back to cache reg_config
docs: hwmon: Add an index file and rename docs to *.rst
docs: hwmon: convert remaining files to ReST format
docs: hwmon: misc files: convert to ReST format
docs: hwmon: pmbus files: convert to ReST format
docs: hwmon: k8temp, w83793: convert to ReST format
docs: hwmon: da9052, da9055: convert to ReST format
docs: hwmon: wm831x, wm8350: convert to ReST format
docs: hwmon: dme1737, vt1211: convert to ReST format
docs: hwmon: ads1015: convert to ReST format
docs: hwmon: asc7621: convert to ReST format
docs: hwmon: ibmpowernv: convert to ReST format
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
|
|
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.
EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We can communicate the clock rate using platform data rather than setting
a flag to use a particular value in the driver, which is cleaner and
avoids the dependency.
No platform in the kernel currently defines the ep93xx keypad device
structure, so this is a rather pointless excercise. Any out of tree
users are probably dead now, but if not, they have to change their
platform code to match the new platform_data structure.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The header file is the only thing preventing us from building the
driver in a cross-platform configuration, so move the structure
we are interested in to the global platform_data location
and enable compile testing.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
PM changes for am335x and am437x
This series adds support for am437x RTC-only mode in suspend. In the
RTC-only mode suspend, everything is shut down except the RTC. This
makes the power consumption very low for suspend mode.
To support RTC-only mode, we need to export omap_rtc_power_off_program()
from the rtc driver and improve PM code to save and restore the wkup
domain context. As RTC-only mode depends on the device being wired
properly for things like memory, we need to also check for the machine
type before we allow it. We also need to run DDR3 hardware leveling on
resume.
Note that there is a trivial merge conflict between the RTC branch
and these changes where the RTC branch makes tm2bcd() a void function
and the error handling parts can be just dropped.
* tag 'omap-for-v5.2/am4-pm-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: sleep43xx: Run EMIF HW leveling on resume path
memory: ti-emif-sram: Add ti_emif_run_hw_leveling for DDR3 hardware leveling
soc: ti: pm33xx: AM437X: Add rtc_only with ddr in self-refresh support
soc: ti: pm33xx: Move the am33xx_push_sram_idle to the top
ARM: OMAP2+: pm33xx: Add support for rtc+ddr in self refresh mode
rtc: OMAP: Add support for rtc-only mode
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Driver changes for ti-sysc for v5.2 merge window
This series of changes for ti-sysc interconnect target module driver
gets us to the point where we can actually drop legacy platform data
for many devices in favor of device tree data.
To do this, we improve ti-sysc driver not to rely on platform data
callbacks to manage module clocks, and handle more quirks needed for
some devices. Also few minor fixes are needed, but were considered
not needed to be sent separately as they only show up with this series.
Then we drop several thousands of lines of legacy platform data for
omap4, omap5, dra7, am335x and am437x. We drop platform data for mmc,
i2c, gpio and uart devices to start with as those are typically
easily tested on all devices. In case of unexpected issues, we can just
add back the legacy platform data for a single device type if needed.
Finally we add initial support for enabling and disabling some devices
without legacy platform data callbacks. I was planning on sending the
dropping of legacy platform data as a separate series, but already
applied Roger's patch on top and pushed it out.
Note that this series depends on related SoC and is based on those.
* tag 'omap-for-v5.2/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
bus: ti-sysc: Add generic enable/disable functions
ARM: OMAP2+: Drop mcspi platform data for omap4
ARM: OMAP2+: Drop uart platform data for dra7
ARM: OMAP2+: Drop gpio platform data for dra7
ARM: OMAP2+: Drop i2c platform data for dra7
ARM: OMAP2+: Drop mmc platform data for dra7
ARM: OMAP2+: Drop uart platform data for omap5
ARM: OMAP2+: Drop gpio platform data for omap5
ARM: OMAP2+: Drop i2c platform data for omap5
ARM: OMAP2+: Drop mmc platform data for omap5
ARM: OMAP2+: Drop uart platform data for am33xx and am43xx
ARM: OMAP2+: Drop gpio platform data for am33xx and am43xx
ARM: OMAP2+: Drop i2c platform data for am33xx and am43xx
ARM: OMAP2+: Drop mmc platform data for am330x and am43xx
ARM: OMAP2+: Drop uart platform data for omap4
ARM: OMAP2+: Drop gpio platform data for omap4
ARM: OMAP2+: Drop i2c platform data for omap4
ARM: OMAP2+: Drop mmc platform data for omap4
Documentation: bus: ti-sysc: fix spelling mistakes "multipe" and "interconnet"
bus: ti-sysc: Detect DMIC for debugging
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds a new slightly rewritten timer driver for the
Intel IXP4xx clocksource, clockevent and delay timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are no in-tree users of the platform data, so remove it to
simplify the code slightly.
Remove the now unused pca954x.h platform data header.
Signed-off-by: Robert Shearman <robert.shearman@att.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The current API for the wilco EC mailbox interface is bad.
It assumes that most messages sent to the EC follow a similar structure,
with a command byte in MBOX[0], followed by a junk byte, followed by
actual data. This doesn't happen in several cases, such as setting the
RTC time, using the raw debugfs interface, and reading or writing
properties such as the Peak Shift policy (this last to be submitted soon).
Similarly for the response message from the EC, the current interface
assumes that the first byte of data is always 0, and the second byte
is unused. However, in both setting and getting the RTC time, in the
debugfs interface, and for reading and writing properties, this isn't
true.
The current way to resolve this is to use WILCO_EC_FLAG_RAW* flags to
specify when and when not to skip these initial bytes in the sent and
received message. They are confusing and used so much that they are
normal, and not exceptions. In addition, the first byte of
response in the debugfs interface is still always skipped, which is
weird, since this raw interface should be giving the entire result.
Additionally, sent messages assume the first byte is a command, and so
struct wilco_ec_message contains the "command" field. In setting or
getting properties however, the first byte is not a command, and so this
field has to be filled with a byte that isn't actually a command. This
is again inconsistent.
wilco_ec_message contains a result field as well, copied from
wilco_ec_response->result. The message result field should be removed:
if the message fails, the cause is already logged, and the callers are
alerted. They will never care about the actual state of the result flag.
These flags and different cases make the wilco_ec_transfer() function,
used in wilco_ec_mailbox(), really gross, dealing with a bunch of
different cases. It's difficult to figure out what it is doing.
Finally, making these assumptions about the structure of a message make
it so that the messages do not correspond well with the specification
for the EC's mailbox interface. For instance, this interface
specification may say that MBOX[9] in the received message contains
some information, but the calling code needs to remember that the first
byte of response is always skipped, and because it didn't set the
RESPONSE_RAW flag, the next byte is also skipped, so this information
is actually contained within wilco_ec_message->response_data[7]. This
makes it difficult to maintain this code in the future.
To fix these problems this patch standardizes the mailbox interface by:
- Removing the WILCO_EC_FLAG_RAW* flags
- Removing the command and reserved_raw bytes from wilco_ec_request
- Removing the mbox0 byte from wilco_ec_response
- Simplifying wilco_ec_transfer() because of these changes
- Gives the callers of wilco_ec_mailbox() the responsibility of exactly
and consistently defining the structure of the mailbox request and
response
- Removing command and result from wilco_ec_message.
This results in the reduction of total code, and makes it much more
maintainable and understandable.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's more than a handful of clk driver fixes for changes that came
in during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Fix PLL_1416X not rounding rates
clk: mediatek: fix clk-gate flag setting
platform/x86: pmc_atom: Drop __initconst on dmi table
clk: x86: Add system specific quirk to mark clocks as critical
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
clk: at91: fix programmable clock for sama5d2
|
|
The GPIO block can enter idle independently of the CPU power management
calls via smart-idle. When the GPIO block enters idle, level detection
stops working due to clocks being shut off, and an alternative form of
edge detection is used. However, this needs the edge detection
registers set to mark the appropriate edges.
Arrange to configure the edge detection enables along with the level
detection to ensure that any transition to active interrupt state that
occurs while the block is idle is detected as a wake-up event.
Since we enable the edge detection when configuring the IRQ, both
omap2_gpio_enable_level_quirk() nor omap2_gpio_disable_level_quirk()
become redundant, which also means OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER
can be removed. This can be now done without regressions as patch
"gpio: gpio-omap: fix level interrupt idling" allows level interrupts
to idle on omap4 without a workaround.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: update description for the fix dependency]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit 648e921888ad ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the pmc_plt_clocks of the Bay Trail SoC are
unconditionally gated off. Unfortunately this will break systems where these
clocks are used for external purposes beyond the kernel's knowledge. Fix it
by implementing a system specific quirk to mark the necessary pmc_plt_clks as
critical.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: David Müller <dave.mueller@gmx.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for rtc+ddr in self refresh mode. Add addtional
pm hooks for save/restore and rtc suspend/resume.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The symbol that is being used in the #if/#endif block is not the one
which is mentioned at the bottom.
Fixes: 93af53b8633c ("nand: omap2: Remove horrible ifdefs to fix module probe")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.
For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.
Let's also group the idle defines together and update the binding
documentation for it.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
spdxcheck.py complains:
include/linux/platform_data/gpio/gpio-amd-fch.h: 1:28 Invalid License ID: GPL+
which is correct because GPL+ is not a valid identifier. Of course this
could have been caught by checkpatch.pl _before_ submitting or merging the
patch.
WARNING: 'SPDX-License-Identifier: GPL+ */' is not supported in LICENSES/...
#271: FILE: include/linux/platform_data/gpio/gpio-amd-fch.h:1:
+/* SPDX-License-Identifier: GPL+ */
Fix it under the assumption that the author meant GPL-2.0+, which makes
sense as the corresponding C file is using that identifier.
Fixes: e09d168f13f0 ("gpio: AMD G-Series PCH gpio driver")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
- SPDX identifier cleanup for platform/chrome
- Cleanup series between mfd and chrome/platform, moving cros-ec
attributes from mfd/cros_ec_dev to sub-drivers in platform/chrome
- Wilco EC driver
- Maintainership change to new group repository
* tag 'tag-chrome-platform-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: fix wilco-ec dependencies
platform/chrome: wilco_ec: Add RTC driver
platform/chrome: wilco_ec: Add support for raw commands in debugfs
platform/chrome: Add new driver for Wilco EC
platform/chrome: cros_ec: Remove cros_ec dependency in lpc_mec
MAINTAINERS: chrome-platform: change the git tree to a chrome-platform group git tree
platform/chrome: cros_ec_sysfs: remove pr_fmt() define
platform/chrome: cros_ec_lightbar: remove pr_fmt() define
platform/chrome: cros_kbd_led_backlight: switch to SPDX identifier
platform/chrome: cros_ec_spi: switch to SPDX identifier
platform/chrome: cros_ec_proto: switch to SPDX identifier
platform/chrome: cros_ec_lpc: switch to SPDX identifier
platform/chrome: cros_ec_i2c: switch to SPDX identifier
platform/chrome: cros_ec_vbc: switch to SPDX identifier
platform/chrome: cros_ec_sysfs: switch to SPDX identifier
platform/chrome: cros_ec_lightbar: switch to SPDX identifier
platform/chrome: cros_ec_debugfs: switch to SPDX identifier
platform/chrome: cromeos_pstore: switch to SPDX identifier
|
|
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- a new watchdog driver for the Mellanox systems
- renesas-wdt: Document r8a77470 support
- numerous 'Mark expected switch fall-throughs'
- qcom: Add suspend/resume support
- some small fixes and documentation updates
* tag 'linux-watchdog-5.1-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: w83877f_wdt: Mark expected switch fall-through
watchdog: sc520_wdt: Mark expected switch fall-through
watchdog: sbc60xxwdt: Mark expected switch fall-through
watchdog: smsc37b787_wdt: Mark expected switch fall-through
watchdog: sc1200: Mark expected switch fall-through
watchdog: pc87413: Mark expected switch fall-through
Documentation/watchdog: Add documentation mlx-wdt driver
watchdog: mlx-wdt: introduce a watchdog driver for Mellanox systems.
platform_data/mlxreg: additions for Mellanox watchdog driver.
watchdog: Update sysfs documentation.
watchdog: dw: remove useless pr_fmt
watchdog: pika_wdt: drop pointless static qualifier in pikawdt_init
watchdog/hpwdt: Update Kconfig documentation
dt-bindings: watchdog: renesas-wdt: Document r8a77470 support
watchdog: qcom: Add suspend/resume support
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- use MODULE_DEVICE_TABLE across several wmi drivers, keeping
wmi_device_id and MODULE_ALIAS() declarations in sync
- add several Ideapad models to the no_hw_rfkill list
- add support for new Mellanox platforms, including new fan and LED
functionality
- address Dell keyboard backlight change event and power button release
issues
- update dell_rbu to use appropriate memory allocation mechanisms
- several small fixes and Ice Lake support for intel_pmc_core
- fix a suspend regression for Cherry Trail based devices in
intel_int0002_vgpio
- a few other routine fixes
* tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86: (50 commits)
MAINTAINERS: Include mlxreg.h in Mellanox Platform Driver files
platform/x86: ideapad-laptop: Add S130-14IGM to no_hw_rfkill list
platform/x86: mlx-platform: Fix access mode for fan_dir attribute
platform/x86: mlx-platform: Add UID LED for the next generation systems
platform/x86: mlx-platform: Add extra CPLD for next generation systems
platform/x86: wmi-bmof: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: intel-wmi-thunderbolt: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: huawei-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi-descriptor: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-smbios-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: wmi: add WMI support to MODULE_DEVICE_TABLE()
platform/x86: wmi: move struct wmi_device_id to mod_devicetable.h
modpost: file2alias: define size of alias
platform/x86: touchscreen_dmi: Add info for the CHUWI Hi10 Air tablet
platform/x86: ideapad-laptop: Add Ideapad 530S-14ARR to no_hw_rfkill list
platform/x86: ideapad-laptop: Add Yoga C930 to no_hw_rfkill_list
platform/x86: intel_pmc_core: Quirk to ignore XTAL shutdown
platform/x86: intel_pmc_core: Add Package cstates residency info
platform/x86: intel_pmc_core: Add ICL platform support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove sensor drivers that got converted from soc_camera
- remaining soc_camera drivers got moved to staging
- some documentation cleanups and improvements
- the imx staging driver now supports imx7
- the ov9640, mt9m001 and mt9m111 got converted from soc_camera
- the vim2m driver now does what a m2m convert driver expects to do
- epoll() fixes on media subsystems
- several drivers fixes, typos, cleanups and improvements
* tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (346 commits)
media: dvb/earth-pt1: fix wrong initialization for demod blocks
media: vim2m: Address some coding style issues
media: vim2m: don't use BUG()
media: vim2m: speedup passthrough copy
media: vim2m: add an horizontal scaler
media: vim2m: don't accept YUYV anymore as output format
media: vim2m: add vertical linear scaler
media: vim2m: better handle cap/out buffers with different sizes
media: vim2m: use different framesizes for bayer formats
media: vim2m: add support for VIDIOC_ENUM_FRAMESIZES
media: vim2m: ensure that width is multiple of two
media: vim2m: improve debug messages
media: vim2m: add bayer capture formats
media: a few more typos at staging, pci, platform, radio and usb
media: Documentation: fix several typos
media: staging: fix several typos
media: include: fix several typos
media: common: fix several typos
media: v4l2-core: fix several typos
media: usb: fix several typos
...
|
