Age | Commit message (Collapse) | Author |
|
ISO 11898-1 specifies in section 11.3.3 "Transmitter delay
compensation" that "the configuration range for [the] SSP position
shall be at least 0 to 63 minimum time quanta."
Because SSP = TDCV + TDCO, it means that we should allow both TDCV and
TDCO to hold zero value in order to honor SSP's minimum possible
value.
However, current implementation assigned special meaning to TDCV and
TDCO's zero values:
* TDCV = 0 -> TDCV is automatically measured by the transceiver.
* TDCO = 0 -> TDC is off.
In order to allow for those values to really be zero and to maintain
current features, we introduce two new flags:
* CAN_CTRLMODE_TDC_AUTO indicates that the controller support
automatic measurement of TDCV.
* CAN_CTRLMODE_TDC_MANUAL indicates that the controller support
manual configuration of TDCV. N.B.: current implementation failed
to provide an option for the driver to indicate that only manual
mode was supported.
TDC is disabled if both CAN_CTRLMODE_TDC_AUTO and
CAN_CTRLMODE_TDC_MANUAL flags are off, c.f. the helper function
can_tdc_is_enabled() which is also introduced in this patch.
Also, this patch adds three fields: tdcv_min, tdco_min and tdcf_min to
struct can_tdc_const. While we are not convinced that those three
fields could be anything else than zero, we can imagine that some
controllers might specify a lower bound on these. Thus, those minimums
are really added "just in case".
Comments of struct can_tdc and can_tdc_const are updated accordingly.
Finally, the changes are applied to the etas_es58x driver.
Link: https://lore.kernel.org/all/20210918095637.20108-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds some helpers for accessing non-phy MDIO devices. They are
analogous to phy_(read|write|modify), except that they take an mdio_device
and not a phy_device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Lots of simnple overlapping additions.
With a build fix from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ucounts fixes from Eric Biederman:
"There has been one very hard to track down bug in the ucount code that
we have been tracking since roughly v5.14 was released. Alex managed
to find a reliable reproducer a few days ago and then I was able to
instrument the code and figure out what the issue was.
It turns out the sigqueue_alloc single atomic operation optimization
did not play nicely with ucounts multiple level rlimits. It turned out
that either sigqueue_alloc or sigqueue_free could be operating on
multiple levels and trigger the conditions for the optimization on
more than one level at the same time.
To deal with that situation I have introduced inc_rlimit_get_ucounts
and dec_rlimit_put_ucounts that just focuses on the optimization and
the rlimit and ucount changes.
While looking into the big bug I found I couple of other little issues
so I am including those fixes here as well.
When I have time I would very much like to dig into process ownership
of the shared signal queue and see if we could pick a single owner for
the entire queue so that all of the rlimits can count to that owner.
That should entirely remove the need to call get_ucounts and
put_ucounts in sigqueue_alloc and sigqueue_free. It is difficult
because Linux unlike POSIX supports setuid that works on a single
thread"
* 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Move get_ucounts from cred_alloc_blank to key_change_session_keyring
ucounts: Proper error handling in set_cred_ucounts
ucounts: Pair inc_rlimit_ucounts with dec_rlimit_ucoutns in commit_creds
ucounts: Fix signal ucount refcounting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, and can.
We'll have one more fix for a socket accounting regression, it's still
getting polished. Otherwise things look fine.
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv", there are
valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of
init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv abort sessions on
receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg() fix
return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails, prevent
stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues"
* tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
usbnet: sanity check for maxpacket
net: enetc: make sure all traffic classes can send large frames
net: enetc: fix ethtool counter name for PM0_TERR
ptp: free 'vclock_index' in ptp_clock_release()
sfc: Don't use netif_info before net_device setup
sfc: Export fibre-specific supported link modes
net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flags
net/mlx5e: IPsec: Fix a misuse of the software parser's fields
net/mlx5e: Fix vlan data lost during suspend flow
net/mlx5: E-switch, Return correct error code on group creation failure
net/mlx5: Lag, change multipath and bonding to be mutually exclusive
ice: Add missing E810 device ids
igc: Update I226_K device ID
e1000e: Fix packet loss on Tiger Lake and later
e1000e: Separate TGP board type from SPT
ptp: Fix possible memory leak in ptp_clock_register()
net: stmmac: Fix E2E delay mechanism
nfc: st95hf: Make spi remove() callback return zero
net: hns3: disable sriov before unload hclge layer
net: hns3: fix vf reset workqueue cannot exit
...
|
|
Pass a single argument to dsa_8021q_rx_vid and dsa_8021q_tx_vid that
contains the necessary information from the two arguments that are
currently provided: the switch and the port number.
Also rename those functions so that they have a dsa_port_* prefix, since
they operate on a struct dsa_port *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Recursion fix for tracing.
While cleaning up some of the tracing recursion protection logic, I
discovered a scenario that the current design would miss, and would
allow an infinite recursion. Removing an optimization trick that
opened the hole fixes the issue and cleans up the code as well"
* tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have all levels of checks prevent recursion
|
|
We have 5 drivers which offset base MAC addr by port id.
Create a helper for them.
This helper takes care of overflows, which some drivers
did not do, please complain if that's going to break
anything!
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for a NULL page->mapping before dereferencing the mapping in
page_is_secretmem(), as the page's mapping can be nullified while gup()
is running, e.g. by reclaim or truncation.
BUG: kernel NULL pointer dereference, address: 0000000000000068
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 4173897 Comm: CPU 3/KVM Tainted: G W
RIP: 0010:internal_get_user_pages_fast+0x621/0x9d0
Code: <48> 81 7a 68 80 08 04 bc 0f 85 21 ff ff 8 89 c7 be
RSP: 0018:ffffaa90087679b0 EFLAGS: 00010046
RAX: ffffe3f37905b900 RBX: 00007f2dd561e000 RCX: ffffe3f37905b934
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffe3f37905b900
...
CR2: 0000000000000068 CR3: 00000004c5898003 CR4: 00000000001726e0
Call Trace:
get_user_pages_fast_only+0x13/0x20
hva_to_pfn+0xa9/0x3e0
try_async_pf+0xa1/0x270
direct_page_fault+0x113/0xad0
kvm_mmu_page_fault+0x69/0x680
vmx_handle_exit+0xe1/0x5d0
kvm_arch_vcpu_ioctl_run+0xd81/0x1c70
kvm_vcpu_ioctl+0x267/0x670
__x64_sys_ioctl+0x83/0xa0
do_syscall_64+0x56/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Link: https://lkml.kernel.org/r/20211007231502.3552715-1-seanjc@google.com
Fixes: 1507f51255c9 ("mm: introduce memfd_secret system call to create "secret" memory areas")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reported-by: Darrick J. Wong <djwong@kernel.org>
Reported-by: Stephen <stephenackerman16@gmail.com>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 6e7b64b9dd6d ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
[akpm@linux-foundation.org: fix um/x86_64, per Catalin]
Link: https://lkml.kernel.org/r/20211006181119.2851441-1-catalin.marinas@arm.com
Link: https://lkml.kernel.org/r/YV6pejGzLy5ppEpt@arm.com
Link: https://lkml.kernel.org/r/20211006082209.417-1-lukas.bulwahn@gmail.com
Fixes: 6e7b64b9dd6d ("elfcore: fix building with clang")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Barret Rhoden <brho@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The node demotion order needs to be updated during CPU hotplug. Because
whether a NUMA node has CPU may influence the demotion order. The
update function should be called during CPU online/offline after the
node_states[N_CPU] has been updated. That is done in
CPUHP_AP_ONLINE_DYN during CPU online and in CPUHP_MM_VMSTAT_DEAD during
CPU offline. But in commit 884a6e5d1f93 ("mm/migrate: update node
demotion order on hotplug events"), the function to update node demotion
order is called in CPUHP_AP_ONLINE_DYN during CPU online/offline. This
doesn't satisfy the order requirement.
For example, there are 4 CPUs (P0, P1, P2, P3) in 2 sockets (P0, P1 in S0
and P2, P3 in S1), the demotion order is
- S0 -> NUMA_NO_NODE
- S1 -> NUMA_NO_NODE
After P2 and P3 is offlined, because S1 has no CPU now, the demotion
order should have been changed to
- S0 -> S1
- S1 -> NO_NODE
but it isn't changed, because the order updating callback for CPU
hotplug doesn't see the new nodemask. After that, if P1 is offlined,
the demotion order is changed to the expected order as above.
So in this patch, we added CPUHP_AP_MM_DEMOTION_ONLINE and
CPUHP_MM_DEMOTION_DEAD to be called after CPUHP_AP_ONLINE_DYN and
CPUHP_MM_VMSTAT_DEAD during CPU online and offline, and register the
update function on them.
Link: https://lkml.kernel.org/r/20210929060351.7293-1-ying.huang@intel.com
Fixes: 884a6e5d1f93 ("mm/migrate: update node demotion order on hotplug events")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Wei Xu <weixugc@google.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Once upon a time, the node demotion updates were driven solely by memory
hotplug events. But now, there are handlers for both CPU and memory
hotplug.
However, the #ifdef around the code checks only memory hotplug. A
system that has HOTPLUG_CPU=y but MEMORY_HOTPLUG=n would miss CPU
hotplug events.
Update the #ifdef around the common code. Add memory and CPU-specific
#ifdefs for their handlers. These memory/CPU #ifdefs avoid unused
function warnings when their Kconfig option is off.
[arnd@arndb.de: rework hotplug_memory_notifier() stub]
Link: https://lkml.kernel.org/r/20211013144029.2154629-1-arnd@kernel.org
Link: https://lkml.kernel.org/r/20210924161255.E5FE8F7E@davehans-spike.ostc.intel.com
Fixes: 884a6e5d1f93 ("mm/migrate: update node demotion order on hotplug events")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Wei Xu <weixugc@google.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The uplink destination type should be used in rules to steer the
packet to the uplink when the device is in steering based LAG mode.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Introduce new APIs to create and destroy flow matcher
for given format id.
Flow match definer object is used for defining the fields and
mask used for the hash calculation. User should mask the desired
fields like done in the match criteria.
This object is assigned to flow group of type hash. In this flow
group type, packets lookup is done based on the hash result.
This patch also adds the required bits to create such flow group.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add new port selection flow steering namespace. Flow steering rules in
this namespaceare are used to determine the physical port for egress
packets.
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/
Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Jisheng Zhang <jszhang@kernel.org>
Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
In commit fda31c50292a ("signal: avoid double atomic counter
increments for user accounting") Linus made a clever optimization to
how rlimits and the struct user_struct. Unfortunately that
optimization does not work in the obvious way when moved to nested
rlimits. The problem is that the last decrement of the per user
namespace per user sigpending counter might also be the last decrement
of the sigpending counter in the parent user namespace as well. Which
means that simply freeing the leaf ucount in __free_sigqueue is not
enough.
Maintain the optimization and handle the tricky cases by introducing
inc_rlimit_get_ucounts and dec_rlimit_put_ucounts.
By moving the entire optimization into functions that perform all of
the work it becomes possible to ensure that every level is handled
properly.
The new function inc_rlimit_get_ucounts returns 0 on failure to
increment the ucount. This is different than inc_rlimit_ucounts which
increments the ucounts and returns LONG_MAX if the ucount counter has
exceeded it's maximum or it wrapped (to indicate the counter needs to
decremented).
I wish we had a single user to account all pending signals to across
all of the threads of a process so this complexity was not necessary
Cc: stable@vger.kernel.org
Fixes: d64696905554 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
v1: https://lkml.kernel.org/r/87mtnavszx.fsf_-_@disp2133
Link: https://lkml.kernel.org/r/87fssytizw.fsf_-_@disp2133
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Tested-by: Rune Kleveland <rune.kleveland@infomedia.dk>
Tested-by: Yu Zhao <yuzhao@google.com>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS for net-next:
1) Add new run_estimation toggle to IPVS to stop the estimation_timer
logic, from Dust Li.
2) Relax superfluous dynset check on NFT_SET_TIMEOUT.
3) Add egress hook, from Lukas Wunner.
4) Nowadays, almost all hook functions in x_table land just call the hook
evaluation loop. Remove remaining hook wrappers from iptables and IPVS.
From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Qdisc::running sequence counter has two uses:
1. Reliably reading qdisc's tc statistics while the qdisc is running
(a seqcount read/retry loop at gnet_stats_add_basic()).
2. As a flag, indicating whether the qdisc in question is running
(without any retry loops).
For the first usage, the Qdisc::running sequence counter write section,
qdisc_run_begin() => qdisc_run_end(), covers a much wider area than what
is actually needed: the raw qdisc's bstats update. A u64_stats sync
point was thus introduced (in previous commits) inside the bstats
structure itself. A local u64_stats write section is then started and
stopped for the bstats updates.
Use that u64_stats sync point mechanism for the bstats read/retry loop
at gnet_stats_add_basic().
For the second qdisc->running usage, a __QDISC_STATE_RUNNING bit flag,
accessed with atomic bitops, is sufficient. Using a bit flag instead of
a sequence counter at qdisc_run_begin/end() and qdisc_is_running() leads
to the SMP barriers implicitly added through raw_read_seqcount() and
write_seqcount_begin/end() getting removed. All call sites have been
surveyed though, and no required ordering was identified.
Now that the qdisc->running sequence counter is no longer used, remove
it.
Note, using u64_stats implies no sequence counter protection for 64-bit
architectures. This can lead to the qdisc tc statistics "packets" vs.
"bytes" values getting out of sync on rare occasions. The individual
values will still be valid.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to directly set a u64_stats_t value which is used to provide an init
function which sets it directly to zero intead of memset() the value.
Add u64_stats_set() to the u64_stats API.
[bigeasy: commit message. ]
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"Bigger than usual for this point in time, the majority is fixing some
issues around BDI lifetimes with the move from the request_queue to
the disk in this release. In detail:
- Series on draining fs IO for del_gendisk() (Christoph)
- NVMe pull request via Christoph:
- fix the abort command id (Keith Busch)
- nvme: fix per-namespace chardev deletion (Adam Manzanares)
- brd locking scope fix (Tetsuo)
- BFQ fix (Paolo)"
* tag 'block-5.15-2021-10-17' of git://git.kernel.dk/linux-block:
block, bfq: reset last_bfqq_created on group change
block: warn when putting the final reference on a registered disk
brd: reduce the brd_devices_mutex scope
kyber: avoid q->disk dereferences in trace points
block: keep q_usage_counter in atomic mode after del_gendisk
block: drain file system I/O on del_gendisk
block: split bio_queue_enter from blk_queue_enter
block: factor out a blk_try_enter_queue helper
block: call submit_bio_checks under q_usage_counter
nvme: fix per-namespace chardev deletion
block/rnbd-clt-sysfs: fix a couple uninitialized variable bugs
nvme-pci: Fix abort command id
|
|
Instead of delaying draining of file system I/O related items like the
blk-qos queues, the integrity read workqueue and timeouts only when the
request_queue is removed, do that when del_gendisk is called. This is
important for SCSI where the upper level drivers that control the gendisk
are separate entities, and the disk can be freed much earlier than the
request_queue, or can even be unbound without tearing down the queue.
Fixes: edb0872f44ec ("block: move the bdi from the request_queue to the gendisk")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-5-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Using "native_port_num" can support more NICs.
Fallback to PCIe IDs if "native_port_num" query fails.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Downstream patches.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, when a user disables roce via the devlink param, this change
isn't passed down to the device.
If device allows disabling RoCE at device level, make use of it. This
instructs the device to skip memory allocations related to RoCE
functionality which otherwise is done by the device.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Replace hard coded timeouts with values stored in firmware's init
segment. Timeouts are read from init segment during driver load. If init
segment timeouts are not supported then fallback to hard coded defaults
instead. Also move pre initialization timeouts which cannot be read from
firmware to the new mechanism.
Signed-off-by: Amir Tzin <amirtz@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add needed structures and defines for DTOR (default timeouts register).
This will be used to get timeouts values from FW instead of hard coded
values in the driver code thus enabling support for slower devices which
need longer timeouts.
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few small fixes.
Mostly driver specific but there's one in the core which fixes a
deadlock when adding devices on spi-mux that's triggered because
spi-mux is a SPI device which is itself a SPI controller and so can
instantiate devices when registered.
We were using a global lock to protect against reusing chip selects
but they're a per controller thing so moving the lock per controller
resolves that"
* tag 'spi-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi-mux: Fix false-positive lockdep splats
spi: Fix deadlock when adding SPI controllers on SPI buses
spi: bcm-qspi: clear MSPI spifie interrupt during probe
spi: spi-nxp-fspi: don't depend on a specific node name erratum workaround
spi: mediatek: skip delays if they are 0
spi: atmel: Fix PDC transfer setup bug
spi: spidev: Add SPI ID table
spi: Use 'flash' node name instead of 'spi-flash' in example
|
|
As the 32-bit arch with 64-bit DMA seems to rare those days,
and page pool might carry a lot of code and complexity for
systems that possibly.
So disable dma mapping support for such systems, if drivers
really want to work on such systems, they have to implement
their own DMA-mapping fallback tracking outside page_pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Moving the of_net code from drivers/of/ to net/core means we
no longer stub out the helpers when networking is disabled,
which leads to a randconfig build failure with at least one
ARM platform that calls this from non-networking code:
arm-linux-gnueabi-ld: arch/arm/mach-mvebu/kirkwood.o: in function `kirkwood_dt_eth_fixup':
kirkwood.c:(.init.text+0x54): undefined reference to `of_get_mac_address'
Restore the way this worked before by changing that #ifdef
check back to testing for both CONFIG_OF and CONFIG_NET.
Fixes: e330fb14590c ("of: net: move of_net under net/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014090055.2058949-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
|
|
This is possible now that the xt_table structure is passed via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is possible now that the xt_table structure is passed via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is possible now that the xt_table structure is passed in via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is possible now that the xt_table structure is passed in via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Support classifying packets with netfilter on egress to satisfy user
requirements such as:
* outbound security policies for containers (Laura)
* filtering and mangling intra-node Direct Server Return (DSR) traffic
on a load balancer (Laura)
* filtering locally generated traffic coming in through AF_PACKET,
such as local ARP traffic generated for clustering purposes or DHCP
(Laura; the AF_PACKET plumbing is contained in a follow-up commit)
* L2 filtering from ingress and egress for AVB (Audio Video Bridging)
and gPTP with nftables (Pablo)
* in the future: in-kernel NAT64/NAT46 (Pablo)
The egress hook introduced herein complements the ingress hook added by
commit e687ad60af09 ("netfilter: add netfilter ingress hook after
handle_ing() under unique static key"). A patch for nftables to hook up
egress rules from user space has been submitted separately, so users may
immediately take advantage of the feature.
Alternatively or in addition to netfilter, packets can be classified
with traffic control (tc). On ingress, packets are classified first by
tc, then by netfilter. On egress, the order is reversed for symmetry.
Conceptually, tc and netfilter can be thought of as layers, with
netfilter layered above tc.
Traffic control is capable of redirecting packets to another interface
(man 8 tc-mirred). E.g., an ingress packet may be redirected from the
host namespace to a container via a veth connection:
tc ingress (host) -> tc egress (veth host) -> tc ingress (veth container)
In this case, netfilter egress classifying is not performed when leaving
the host namespace! That's because the packet is still on the tc layer.
If tc redirects the packet to a physical interface in the host namespace
such that it leaves the system, the packet is never subjected to
netfilter egress classifying. That is only logical since it hasn't
passed through netfilter ingress classifying either.
Packets can alternatively be redirected at the netfilter layer using
nft fwd. Such a packet *is* subjected to netfilter egress classifying
since it has reached the netfilter layer.
Internally, the skb->nf_skip_egress flag controls whether netfilter is
invoked on egress by __dev_queue_xmit(). Because __dev_queue_xmit() may
be called recursively by tunnel drivers such as vxlan, the flag is
reverted to false after sch_handle_egress(). This ensures that
netfilter is applied both on the overlay and underlying network.
Interaction between tc and netfilter is possible by setting and querying
skb->mark.
If netfilter egress classifying is not enabled on any interface, it is
patched out of the data path by way of a static_key and doesn't make a
performance difference that is discernible from noise:
Before: 1537 1538 1538 1537 1538 1537 Mb/sec
After: 1536 1534 1539 1539 1539 1540 Mb/sec
Before + tc accept: 1418 1418 1418 1419 1419 1418 Mb/sec
After + tc accept: 1419 1424 1418 1419 1422 1420 Mb/sec
Before + tc drop: 1620 1619 1619 1619 1620 1620 Mb/sec
After + tc drop: 1616 1624 1625 1624 1622 1619 Mb/sec
When netfilter egress classifying is enabled on at least one interface,
a minimal performance penalty is incurred for every egress packet, even
if the interface it's transmitted over doesn't have any netfilter egress
rules configured. That is caused by checking dev->nf_hooks_egress
against NULL.
Measurements were performed on a Core i7-3615QM. Commands to reproduce:
ip link add dev foo type dummy
ip link set dev foo up
modprobe pktgen
echo "add_device foo" > /proc/net/pktgen/kpktgend_3
samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh -i foo -n 400000000 -m "11:11:11:11:11:11" -d 1.1.1.1
Accept all traffic with tc:
tc qdisc add dev foo clsact
tc filter add dev foo egress bpf da bytecode '1,6 0 0 0,'
Drop all traffic with tc:
tc qdisc add dev foo clsact
tc filter add dev foo egress bpf da bytecode '1,6 0 0 2,'
Apply this patch when measuring packet drops to avoid errors in dmesg:
https://lore.kernel.org/netdev/a73dda33-57f4-95d8-ea51-ed483abd6a7a@iogearbox.net/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Laura García Liébana <nevola@gmail.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Prepare for addition of a netfilter egress hook by generalizing the
ingress hook include file.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Prepare for addition of a netfilter egress hook by renaming
<linux/netfilter_ingress.h> to <linux/netfilter_netdev.h>.
The egress hook also necessitates a refactoring of the include file,
but that is done in a separate commit to ease reviewing.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
random_ether_addr() was the original name of the helper which
was kept for backward compatibility (?) after the rename in
commit 0a4dd594982a ("etherdevice: Rename random_ether_addr
to eth_random_addr").
We have a single random_ether_addr() caller left in tree
while there are 70 callers of eth_random_addr().
Time to drop this define.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211013205450.328092-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The implement of function netdev_all_upper_get_next_dev_rcu has been
removed in:
commit f1170fd462c6 ("net: Remove all_adj_list and its references")
so delete redundant declaration in header file.
Fixes: f1170fd462c6 ("net: Remove all_adj_list and its references")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Link: https://lore.kernel.org/r/20211013094702.3931071-1-chenwandun@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-10-12
* tag 'mlx5-fixes-2021-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors
net/mlx5e: Mutually exclude RX-FCS and RX-port-timestamp
net/mlx5e: Switchdev representors are not vlan challenged
net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error path
net/mlx5e: Allow only complete TXQs partition in MQPRIO channel mode
net/mlx5: Fix cleanup of bridge delayed work
====================
Link: https://lore.kernel.org/r/20211012205323.20123-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Building an allmodconfig kernel arm64 kernel, the following build error
shows up:
In file included from drivers/crypto/marvell/octeontx2/cn10k_cpt.c:4:
include/linux/soc/marvell/octeontx2/asm.h:38:15: error: unknown type name 'u64'
38 | static inline u64 otx2_atomic64_fetch_add(u64 incr, u64 *ptr)
| ^~~
Include linux/types.h in asm.h so the compiler knows what the type
'u64' are.
Fixes: af3826db74d1 ("octeontx2-pf: Use hardware register for CQE count")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20211013135743.3826594-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__dev_addr_set() and dev_addr_mod() and pretty low level,
let the arguments be void, there's no chance for confusion
in callers converted to use them. Keep u8 in dev_addr_set()
because some of the callers are converted from a loop
and we want to make sure assignments are not from an array
of a different type.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|