| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea521e6 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the LE Direct Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the LE Extended Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the LE Advertising Report events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the Extended Inquiry Result events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the Inquiry Result with RSSI events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the Inquiry Result events received
have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the Number of Complete Packets events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This uses skb_pull_data to check the BR/EDR events received have the
minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
num_keys is actually 2 octects not 1:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1989:
Num_Keys_Deleted:
Size: 2 octets
0xXXXX Number of Link Keys Deleted
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Both max_num_keys and num_key are 2 octects:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1985:
Max_Num_Keys:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Num_Keys_Read:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This event is received when the controller stops advertising,
specifically for these three reasons:
(a) Connection is successfully created (success).
(b) Timeout is reached (error).
(c) Number of advertising events is reached (error).
(*) This event is NOT generated when the host stops the advertisement.
Refer to the BT spec ver 5.3 vol 4 part E sec 7.7.65.18. Note that the
section was revised from BT spec ver 5.0 vol 2 part E sec 7.7.65.18
which was ambiguous about (*).
Some chips (e.g. RTL8822CE) send this event when the host stops the
advertisement with status = HCI_ERROR_CANCELLED_BY_HOST (due to (*)
above). This is treated as an error and the advertisement will be
removed and userspace will be informed via MGMT event.
On suspend, we are supposed to temporarily disable advertisements,
and continue advertising on resume. However, due to the behavior
above, the advertisements are removed instead.
This patch returns early if HCI_ERROR_CANCELLED_BY_HOST is received.
Btmon snippet of the unexpected behavior:
@ MGMT Command: Remove Advertising (0x003f) plen 1
Instance: 1
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
Extended advertising: Disabled (0x00)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x01
Duration: 0 ms (0x00)
Max ext adv events: 0
> HCI Event: LE Meta Event (0x3e) plen 6
LE Advertising Set Terminated (0x12)
Status: Operation Cancelled by Host (0x44)
Handle: 1
Connection handle: 0
Number of completed extended advertising events: 5
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
Status: Success (0x00)
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
For HFP offload use case, codec needs to be configured
before opening SCO connection. This patch sends
HCI_CONFIGURE_DATA_PATH command to configure doec before
opening SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
< HCI Command: Enhanced Setup Synchronous Connection (0x01|0x003d) plen 59
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
Retransmission effort: Optimize for link quality (0x02)
> HCI Event: Command Status (0x0f) plen 4
Enhanced Setup Synchronous Connection (0x01|0x003d) ncmd 1
Status: Success (0x00)
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Success (0x00)
Handle: 257
Address: CC:98:8B:92:04:FD (SONY Visual Products Inc.)
Link type: eSCO (0x02)
Transmission interval: 0x0c
Retransmission window: 0x06
RX packet length: 60
TX packet length: 60
Air mode: Transparent (0x03)
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add BT_CODEC option for getsockopt systemcall to get the details
of offload codecs supported over SCO socket
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use V2 version of read local supported command is controller
supports
snoop:
> HCI Event: Command Complete (0x0e) plen 20
Read Local Supported Codecs V2 (0x04|0x000d) ncmd 1
Status: Success (0x00)
Number of supported codecs: 7
Codec: u-law log (0x00)
Logical Transport Type: 0x02
Codec supported over BR/EDR SCO and eSCO
Codec: A-law log (0x01)
Logical Transport Type: 0x02
Codec supported over BR/EDR SCO and eSCO
Codec: CVSD (0x02)
Logical Transport Type: 0x02
Codec supported over BR/EDR SCO and eSCO
Codec: Transparent (0x03)
Logical Transport Type: 0x02
Codec supported over BR/EDR SCO and eSCO
Codec: Linear PCM (0x04)
Logical Transport Type: 0x02
Codec supported over BR/EDR SCO and eSCO
Codec: Reserved (0x08)
Logical Transport Type: 0x03
Codec supported over BR/EDR ACL
Codec supported over BR/EDR SCO and eSCO
Codec: mSBC (0x05)
Logical Transport Type: 0x03
Codec supported over BR/EDR ACL
Codec supported over BR/EDR SCO and eSCO
Number of vendor codecs: 0
......
< HCI Command: Read Local Suppor.. (0x04|0x000e) plen 7
Codec: mSBC (0x05)
Logical Transport Type: 0x00
Direction: Input (Host to Controller) (0x00)
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Codec Capabilities (0x04|0x000e) ncmd 1
Status: Success (0x00)
Number of codec capabilities: 1
Capabilities #0:
00 00 11 15 02 33
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move reading of supported local codecs into a separate init function,
query codecs capabilities and cache the data
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch allows a user space process to enable/disable the quality
report events dynamically through the set experimental feature mgmt
interface.
Since the quality report feature needs to invoke the callback function
provided by the driver, i.e., hdev->set_quality_report, a valid
controller index is required.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
These command do have variable length and the length can go up to 251,
so this changes the struct to not use a fixed size and then when
creating the PDU only the actual length of the data send to the
controller.
Fixes: a0fb3726ba551 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
blacklist -> reject list
whitelist -> accept list
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced when describing the
connectionless peripheral broadcast feature:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
These attributes are not used elsewhere in the code.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During command status or command complete event, the controller may set
ncmd=0 indicating that it is not accepting any more commands. In such a
case, host holds off sending any more commands to the controller. If the
controller doesn't recover from such condition, host will wait forever,
until the user decides that the Bluetooth is broken and may power cycles
the Bluetooth.
This patch triggers the hardware error to reset the controller and
driver when it gets into such state as there is no other wat out.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During suspend, there are a few scan enable and set event filter
commands that don't need to be sent unless there are actual BR/EDR
devices capable of waking the system. Check the HCI_PSCAN bit before
writing scan enable and use a new dev flag, HCI_EVENT_FILTER_CONFIGURED
to control whether to clear the event filter.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.
These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.
This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.
This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba258ae (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This change adds the relevant driver and quirk to allow drivers to
report the le_states as being trustworthy.
This has historically been disabled as controllers did not reliably
support this. In particular, this will be used to relax this condition
for controllers that have been well tested and reliable.
/* Most controller will fail if we try to create new connections
* while we have an existing one in slave role.
*/
if (hdev->conn_hash.le_num_slave > 0)
return NULL;
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The list of LE features constants has gotten a bit confused. It lost the
order and gained duplicated. Clean this up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch assigns the next free HCI device identifier to Bluetooth
devices based on VIRTIO devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch provides a mechanism for MGMT interface client to query the
capability of the controller to support WBS.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This change simply fixes a few typos in the quirk definitions.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.
As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).
So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
These adds the HCI definitions for handling CIS connections along with
ISO data packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This handles LE PHY Update Complete event and store both tx_phy and
rx_phy into hci_conn.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.
As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
