| Age | Commit message (Collapse) | Author |
|---|
|
Some older laptops using cs35l41 use firmware which does not support
the CSPL_MBOX_CMD_SPK_OUT_ENABLE command.
Firmware versions v0.28.0 and older do not support this command.
Fixes: fa3efcc36aac ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The existing code checks for the correct state transition after sending
a command. However, it is possible for the message box to return -1,
which indicates an error, if an error has occurred in the firmware.
We can detect if the error has occurred, and return a different error.
In addition, there is no recovering from a CSPL error, so the retry
mechanism is not needed in this case, and we can return immediately.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231026150558.2105827-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To ensure the chip has correctly reset during probe and system suspend,
we need to force a software reset, in case of systems where the
hardware reset is not available.
The software reset register was labelled as volatile but not readable,
however, it is readable, (just returns 0x0). Adding it to readable
registers means it will be correctly treated as volatile, and thus
will not be cached.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Enabling the active/passive shared boosts requires setting SYNC_EN, but
*not* before receiving the PLL Lock signal.
Due to improper error handling, it was not obvious that waiting for the
completion operation times out and, consequently, the shared boost is
never activated.
Further investigations revealed the signal is triggered while
snd_pcm_start() is executed, right after receiving the
SNDRV_PCM_TRIGGER_START command, which happens long after the
SND_SOC_DAPM_PRE_PMU event handler is invoked as part of
snd_pcm_prepare(). That is where cs35l41_global_enable() is called
from.
Increasing the wait duration doesn't help, as it only causes an
unnecessary delay in the invocation of snd_pcm_start(). Moving the wait
and the subsequent regmap operations to the SNDRV_PCM_TRIGGER_START
callback is not a solution either, since they would be executed in an
IRQ-off atomic context.
Solve the issue by setting the SYNC_EN bit in PWR_CTRL3 register right
after receiving the PLL Lock interrupt.
Additionally, drop the unnecessary writes to PWR_CTRL1 register, part of
the original mdsync_up_seq, which would have toggled GLOBAL_EN with
unwanted consequences on PLL locking behavior.
Fixes: f5030564938b ("ALSA: cs35l41: Add shared boost feature")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: David Rhodes <david.rhodes@cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Shared boost allows two amplifiers to share a single boost circuit by
communicating on the MDSYNC bus.
The passive amplifier does not control the boost and receives data from
the active amplifier.
Shared Boost is not supported in HDA Systems.
Based on David Rhodes shared boost patches.
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Reviewed-by: David Rhodes <david.rhodes@cirrus.com>
Link: https://lore.kernel.org/r/20230223084324.9076-4-lucas.tanure@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.20
This is a big release thus far and there will probably be more changes
to come, it's a combination of a larger than usual crop of new drivers
and some subsysetm wide cleanups from Charles rather than anything
structural. The SOF and Intel DSP code both also continue to be very
actively developed.
- Restructing of the set_fmt() callbacks to be specified in terms of
the device rather than with semantics depending on if the device is
supposed to be a CODEC or SoC, making things clearer in situations
like CODEC to CODEC links.
- Clean up of the way we flag which DAI naming scheme we use to reflect
the progress that's been made modernising things.
- Merge of more of the Intel AVS driver stack, including some board
integrations.
- New version 4 mechanism for communication with SOF DSPs.
- Suppoort for dynamically selecting the PLL to use at runtime on i.MX
platforms.
- Improvements for CODEC to CODEC support in the generic cards.
- Support for AMD Jadeite and various machines, Intel MetorLake DSPs,
Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP
TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments
TAS2780.
|
|
This patch adds support for the CS35L41 DSP.
The DSP allows for extra features, such as running
speaker protection algorithms and hibernations.
To utilize these features, the driver must load
firmware into the DSP, as well as various tuning
files which allow for customization for specific
models.
[ Slightly simplified Kconfig changes by tiwai ]
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-5-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since the CS35L41 HDA driver also support hibernation, it
makes sense to move code from the ASoC driver to enter
hibernation into common code.
Since HDA must support laptops which do not support hibernation
due to lack of external boost GPIO it is necessary to
ensure the function returns an error when an unsupported
boost type is in use.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220525131638.5512-12-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
CS35L41 HDA Driver will support hibernation using DSP firmware,
move the exit hibernate function into shared code so this can
be reused.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220525131638.5512-10-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
|
|
This can then be used by HDA code to configure cs_dsp.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-9-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This sequence is required to setup firmware, and will
be needed for hda driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-8-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This function is used to control the DSP Firmware for cs35l41,
and will be needed by the cs35l41 hda driver, when firmware
support is added.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-7-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CS35L41 can produce interrupts on error.
When the interrupts occur, the driver will report
the error, but errors will only be fixed after playback
finishes.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220509214703.4482-5-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for external boost voltage, where GPIO1 must control a
switch to isolate CS35L41 from the external Boost Voltage
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220413083728.10730-17-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To add support for external boost for ASoC move the HDA external
boost implementation to the shared lib.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-15-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Having CS35L41_PWR_CTRL2 on cs35l41_hda_config overwrites the boost
configuration for internal boost.
So move it to the initialization part and use regmap_update_bits to
only change the correct bits.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-11-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace vspk_always_on by a enum that better characterizes the boost
type, as there is 3 types of boost hardware.
And with the new boost type other parts of the driver can better handle
the configuration of the chip.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-7-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ASoC and HDA can use a single function to configure the chip gpios.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-4-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The driver can receive an empty hw_config, so mark as valid if
successfully read from device tree/ACPI or set by the driver itself.
Platforms not marked with a valid hw config will not be supported.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-3-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Both ASoC and HDA require to configure the GPIOs and Boost, so
create a single shared struct for hardware configuration.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220413083728.10730-2-tanureal@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CS35L41_NUM_OTP_ELEM is 100, but only 99 entries are defined in
the array otp_map_1/2[CS35L41_NUM_OTP_ELEM], this will trigger UBSAN
to report a shift-out-of-bounds warning in the cs35l41_otp_unpack()
since the last entry in the array will result in GENMASK(-1, 0).
UBSAN reports this problem:
UBSAN: shift-out-of-bounds in /home/hwang4/build/jammy/jammy/sound/soc/codecs/cs35l41-lib.c:836:8
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 10 PID: 595 Comm: systemd-udevd Not tainted 5.15.0-23-generic #23
Hardware name: LENOVO \x02MFG_IN_GO/\x02MFG_IN_GO, BIOS N3GET19W (1.00 ) 03/11/2022
Call Trace:
<TASK>
show_stack+0x52/0x58
dump_stack_lvl+0x4a/0x5f
dump_stack+0x10/0x12
ubsan_epilogue+0x9/0x45
__ubsan_handle_shift_out_of_bounds.cold+0x61/0xef
? regmap_unlock_mutex+0xe/0x10
cs35l41_otp_unpack.cold+0x1c6/0x2b2 [snd_soc_cs35l41_lib]
cs35l41_hda_probe+0x24f/0x33a [snd_hda_scodec_cs35l41]
cs35l41_hda_i2c_probe+0x65/0x90 [snd_hda_scodec_cs35l41_i2c]
? cs35l41_hda_i2c_remove+0x20/0x20 [snd_hda_scodec_cs35l41_i2c]
i2c_device_probe+0x252/0x2b0
Fixes: 6450ef559056 ("ASoC: cs35l41: CS35L41 Boosted Smart Amplifier")
Reviewed-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220328123535.50000-2-hui.wang@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cs35l41 supports a low power DSP memory retention mode. Add support
for entering this mode when then device is not in use.
Co-authored-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for the addition of PM runtime support move the test
key out of the register patches themselves. This is necessary to
allow the test key to be held during cache synchronisation, which is
required by the OTP settings which were unpacked from the device and
written by the driver.
Also whilst at it, the driver uses a mixture of accessing the test key
register by name and by address, consistently use the name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will use the same registers to configure
internal boost for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-7-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will use the same register to set channels
for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA systems require the same errata patches, so
move it to the shared code using a function the correctly
applies the patches by revision
Also, move CS35L41_DSP1_CCM_CORE_CTRL write to errata
patch function as is required to be written at boot,
but not in regmap_register_patch sequence as will affect
waking up from hibernation
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-5-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will do the same cs35l41_otp_unpack, so move it
to shared code
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-3-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To support CS35L41 in HDA systems the HDA driver
for CS35L41 would have to duplicate some functions
that already exist on ASoC driver
So instead of duplicate the code, use the new lib
source as a shared resource for both ASoC and HDA
Also, change the way CONFIG_SND_SOC_CS35L41 is
selected, as reported by Intel Kernel test robot,
it is possible to build SND_SOC_CS35L41_SPI/I2C
without the main driver, which would lead to build
failures.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SoC Audio driver for the Cirrus Logic CS35L41 amplifier
Signed-off-by: David Rhodes <drhodes@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210907225719.2018115-2-drhodes@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
