| Age | Commit message (Collapse) | Author |
|---|
|
Pass the supported PHY interface types to phylib so that PHY drivers
can select an appropriate host configuration mode for their interface
according to the host capabilities.
This is only done for SFP modules presently.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Provide phy driver start/stop hooks so that the PHY driver knows when
the network driver is starting or stopping. This will be used for the
Marvell 10G driver so that we can sanely refuse to start if the PHYs
firmware is not present, and also so that we can sanely support SFPs
behind the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow phylib drivers to pass the hardware-resolved pause state to MAC
drivers, rather than using the software-based pause resolution code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a new DSA switch operation, phylink_get_interfaces, which should
fill in which PHY_INTERFACE_MODE_* are supported by given port.
Use this before phylink_create to fill phylink's config
supported_interfaces member.
This allows for phylink to determine which PHY_INTERFACE_MODE to use
with SFP modules.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a PHY interface bitmap for the MAC driver to specify which PHY
interfaces are supported to phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A single fix for an issue introduced this development cycle: when
running as a Xen guest on Arm systems the kernel will hang during
boot"
* tag 'for-linus-5.11-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: Don't probe xenbus as part of an early initcall
|
|
After Commit 3499ba8198cad ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org
Fixes: 3499ba8198cad ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Pull networking fixes from David Miller:
"Another pile of networing fixes:
1) ath9k build error fix from Arnd Bergmann
2) dma memory leak fix in mediatec driver from Lorenzo Bianconi.
3) bpf int3 kprobe fix from Alexei Starovoitov.
4) bpf stackmap integer overflow fix from Bui Quang Minh.
5) Add usb device ids for Cinterion MV31 to qmi_qwwan driver, from
Christoph Schemmel.
6) Don't update deleted entry in xt_recent netfilter module, from
Jazsef Kadlecsik.
7) Use after free in nftables, fix from Pablo Neira Ayuso.
8) Header checksum fix in flowtable from Sven Auhagen.
9) Validate user controlled length in qrtr code, from Sabyrzhan
Tasbolatov.
10) Fix race in xen/netback, from Juergen Gross,
11) New device ID in cxgb4, from Raju Rangoju.
12) Fix ring locking in rxrpc release call, from David Howells.
13) Don't return LAPB error codes from x25_open(), from Xie He.
14) Missing error returns in gsi_channel_setup() from Alex Elder.
15) Get skb_copy_and_csum_datagram working properly with odd segment
sizes, from Willem de Bruijn.
16) Missing RFS/RSS table init in enetc driver, from Vladimir Oltean.
17) Do teardown on probe failure in DSA, from Vladimir Oltean.
18) Fix compilation failures of txtimestamp selftest, from Vadim
Fedorenko.
19) Limit rx per-napi gro queue size to fix latency regression, from
Eric Dumazet.
20) dpaa_eth xdp fixes from Camelia Groza.
21) Missing txq mode update when switching CBS off, in stmmac driver,
from Mohammad Athari Bin Ismail.
22) Failover pending logic fix in ibmvnic driver, from Sukadev
Bhattiprolu.
23) Null deref fix in vmw_vsock, from Norbert Slusarek.
24) Missing verdict update in xdp paths of ena driver, from Shay
Agroskin.
25) seq_file iteration fix in sctp from Neil Brown.
26) bpf 32-bit src register truncation fix on div/mod, from Daniel
Borkmann.
27) Fix jmp32 pruning in bpf verifier, from Daniel Borkmann.
28) Fix locking in vsock_shutdown(), from Stefano Garzarella.
29) Various missing index bound checks in hns3 driver, from Yufeng Mo.
30) Flush ports on .phylink_mac_link_down() in dsa felix driver, from
Vladimir Oltean.
31) Don't mix up stp and mrp port states in bridge layer, from Horatiu
Vultur.
32) Fix locking during netif_tx_disable(), from Edwin Peer"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
bpf: Fix 32 bit src register truncation on div/mod
bpf: Fix verifier jmp32 pruning decision logic
bpf: Fix verifier jsgt branch analysis on max bound
vsock: fix locking in vsock_shutdown()
net: hns3: add a check for index in hclge_get_rss_key()
net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
net: hns3: add a check for queue_id in hclge_reset_vf_queue()
net: dsa: felix: implement port flushing on .phylink_mac_link_down
switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
net: watchdog: hold device global xmit lock during tx disable
netfilter: nftables: relax check for stateful expressions in set definition
netfilter: conntrack: skip identical origin tuple in same zone only
vsock/virtio: update credit only if socket is not closed
net: fix iteration for sctp transport seq_files
net: ena: Update XDP verdict upon failure
net/vmw_vsock: improve locking in vsock_connect_timeout()
net/vmw_vsock: fix NULL pointer dereference
ibmvnic: Clear failover_pending if unable to schedule
net: stmmac: set TxQ mode back to DCB after disabling CBS
...
|
|
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <maskray@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes: c284b545900830 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes: c3f26a269c24 ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Prevent device managed IRQ allocation helpers from returning IRQ 0
- A fix for MSI activation of PCI endpoints with multiple MSIs
* tag 'irq_urgent_for_v5.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent [devm_]irq_alloc_desc from returning irq 0
genirq/msi: Activate Multi-MSI early when MSI_FLAG_ACTIVATE_EARLY is set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull syscall entry fixes from Borislav Petkov:
- For syscall user dispatch, separate prctl operation from syscall
redirection range specification before the API has been made official
in 5.11.
- Ensure tasks using the generic syscall code do trap after returning
from a syscall when single-stepping is requested.
* tag 'core_urgent_for_v5.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Use different define for selector variable in SUD
entry: Ensure trap after single-step on system call return
|
|
Michael Kerrisk suggested that, from an API perspective, it is a bad
idea to share the PR_SYS_DISPATCH_ defines between the prctl operation
and the selector variable.
Therefore, define two new constants to be used by SUD's selector variable
and update the corresponding documentation and test cases.
While this changes the API syscall user dispatch has never been part of a
Linux release, it will show up for the first time in 5.11.
Suggested-by: Michael Kerrisk (man-pages) <mtk.manpages@gmail.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210205184321.2062251-1-krisman@collabora.com
|
|
Commit 299155244770 ("entry: Drop usage of TIF flags in the generic syscall
code") introduced a bug on architectures using the generic syscall entry
code, in which processes stopped by PTRACE_SYSCALL do not trap on syscall
return after receiving a TIF_SINGLESTEP.
The reason is that the meaning of TIF_SINGLESTEP flag is overloaded to
cause the trap after a system call is executed, but since the above commit,
the syscall call handler only checks for the SYSCALL_WORK flags on the exit
work.
Split the meaning of TIF_SINGLESTEP such that it only means single-step
mode, and create a new type of SYSCALL_WORK to request a trap immediately
after a syscall in single-step mode. In the current implementation, the
SYSCALL_WORK flag shadows the TIF_SINGLESTEP flag for simplicity.
Update x86 to flip this bit when a tracer enables single stepping.
Fixes: 299155244770 ("entry: Drop usage of TIF flags in the generic syscall code")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kyle Huey <me@kylehuey.com>
Link: https://lore.kernel.org/r/87h7mtc9pr.fsf_-_@collabora.com
|
|
Merge misc fixes from Andrew Morton:
"18 patches.
Subsystems affected by this patch series: mm (hugetlb, compaction,
vmalloc, shmem, memblock, pagecache, kasan, and hugetlb), mailmap,
gcov, ubsan, and MAINTAINERS"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS/.mailmap: use my @kernel.org address
mm: hugetlb: fix missing put_page in gather_surplus_pages()
ubsan: implement __ubsan_handle_alignment_assumption
kasan: make addr_has_metadata() return true for valid addresses
kasan: add explicit preconditions to kasan_report()
mm/filemap: add missing mem_cgroup_uncharge() to __add_to_page_cache_locked()
mailmap: add entries for Manivannan Sadhasivam
mailmap: fix name/email for Viresh Kumar
memblock: do not start bottom-up allocations with kernel_end
mm: thp: fix MADV_REMOVE deadlock on shmem THP
init/gcov: allow CONFIG_CONSTRUCTORS on UML to fix module gcov
mm/vmalloc: separate put pages and flush VM flags
mm, compaction: move high_pfn to the for loop scope
mm: migrate: do not migrate HugeTLB page whose refcount is one
mm: hugetlb: remove VM_BUG_ON_PAGE from page_huge_active
mm: hugetlb: fix a race between isolating and freeing page
mm: hugetlb: fix a race between freeing and dissolving the page
mm: hugetlbfs: fix cannot migrate the fallocated HugeTLB page
|
|
Since commit a85a6c86c25b ("driver core: platform: Clarify that IRQ 0
is invalid"), having a linux-irq with number 0 will trigger a WARN()
when calling platform_get_irq*() to retrieve that linux-irq.
Since [devm_]irq_alloc_desc allocs a single irq and since irq 0 is not used
on some systems, it can return 0, triggering that WARN(). This happens
e.g. on Intel Bay Trail and Cherry Trail devices using the LPE audio engine
for HDMI audio:
0 is an invalid IRQ number
WARNING: CPU: 3 PID: 472 at drivers/base/platform.c:238 platform_get_irq_optional+0x108/0x180
Modules linked in: snd_hdmi_lpe_audio(+) ...
Call Trace:
platform_get_irq+0x17/0x30
hdmi_lpe_audio_probe+0x4a/0x6c0 [snd_hdmi_lpe_audio]
---[ end trace ceece38854223a0b ]---
Change the 'from' parameter passed to __[devm_]irq_alloc_descs() by the
[devm_]irq_alloc_desc macros from 0 to 1, so that these macros will no
longer return 0.
Fixes: a85a6c86c25b ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201221185647.226146-1-hdegoede@redhat.com
|
|
Patch series "kasan: Fix metadata detection for KASAN_HW_TAGS", v5.
With the introduction of KASAN_HW_TAGS, kasan_report() currently assumes
that every location in memory has valid metadata associated. This is
due to the fact that addr_has_metadata() returns always true.
As a consequence of this, an invalid address (e.g. NULL pointer
address) passed to kasan_report() when KASAN_HW_TAGS is enabled, leads
to a kernel panic.
Example below, based on arm64:
BUG: KASAN: invalid-access in 0x0
Read at addr 0000000000000000 by task swapper/0/1
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
...
Call trace:
mte_get_mem_tag+0x24/0x40
kasan_report+0x1a4/0x410
alsa_sound_last_init+0x8c/0xa4
do_one_initcall+0x50/0x1b0
kernel_init_freeable+0x1d4/0x23c
kernel_init+0x14/0x118
ret_from_fork+0x10/0x34
Code: d65f03c0 9000f021 f9428021 b6cfff61 (d9600000)
---[ end trace 377c8bb45bdd3a1a ]---
hrtimer: interrupt took 48694256 ns
note: swapper/0[1] exited with preempt_count 1
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
SMP: stopping secondary CPUs
Kernel Offset: 0x35abaf140000 from 0xffff800010000000
PHYS_OFFSET: 0x40000000
CPU features: 0x0a7e0152,61c0a030
Memory Limit: none
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
This series fixes the behavior of addr_has_metadata() that now returns
true only when the address is valid.
This patch (of 2):
With the introduction of KASAN_HW_TAGS, kasan_report() accesses the
metadata only when addr_has_metadata() succeeds.
Add a comment to make sure that the preconditions to the function are
explicitly clarified.
Link: https://lkml.kernel.org/r/20210126134409.47894-1-vincenzo.frascino@arm.com
Link: https://lkml.kernel.org/r/20210126134409.47894-2-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: "Paul E . McKenney" <paulmck@kernel.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When VM_MAP_PUT_PAGES was added, it was defined with the same value as
VM_FLUSH_RESET_PERMS. This doesn't seem like it will cause any big
functional problems other than some excess flushing for VM_MAP_PUT_PAGES
allocations.
Redefine VM_MAP_PUT_PAGES to have its own value. Also, rearrange things
so flags are less likely to be missed in the future.
Link: https://lkml.kernel.org/r/20210122233706.9304-1-rick.p.edgecombe@intel.com
Fixes: b944afc9d64d ("mm: add a VM_MAP_PUT_PAGES flag for vmap")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Axtens <dja@axtens.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a new hugetlb page is allocated during fallocate it will not be
marked as active (set_page_huge_active) which will result in a later
isolate_huge_page failure when the page migration code would like to
move that page. Such a failure would be unexpected and wrong.
Only export set_page_huge_active, just leave clear_page_huge_active as
static. Because there are no external users.
Link: https://lkml.kernel.org/r/20210115124942.46403-3-songmuchun@bytedance.com
Fixes: 70c3547e36f5 (hugetlbfs: add hugetlbfs_fallocate())
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Fix a possible NULL-ptr dereference in dev_iommu_priv_get() which is
too easy to accidentially trigger from IOMMU drivers.
In the current case the AMD IOMMU driver triggered it on some machines
in the IO-page-fault path, so fix it once and for all"
* tag 'iommu-fixes-v5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Check dev->iommu in dev_iommu_priv_get() before dereferencing it
|
|
Pull drm fixes from Dave Airlie:
"Fixes for rc7, bit bigger than I'd like at this stage, but most of the
i915 stuff and some amdgpu is destined for staging and I'd rather not
hold it up, the i915 changes also pulled in a few precusor code
movement patches to make things cleaner, but nothing seems that
horrible, and I've checked over all of it.
Otherwise there is a nouveau dma-api warning regression, and a ttm
page allocation warning fix, and some fixes for a bridge chip,
ttm:
- fix huge page warning regression
i915:
- Skip vswing programming for TBT
- Power up combo PHY lanes for HDMI
- Fix double YUV range correction on HDR planes
- Fix the MST PBN divider calculation
- Fix LTTPR vswing/pre-emp setting in non-transparent mode
- Move the breadcrumb to the signaler if completed upon cancel
- Close race between enable_breadcrumbs and cancel_breadcrumbs
- Drop lru bumping on display unpinning
amdgpu:
- Fix retry in gem create
- Vangogh fixes
- Fix for display from shared buffers
- Various display fixes
amdkfd:
- Fix regression in buffer free
nouveau:
- fix DMA API warning regression
drm/bridge/lontium-lt9611uxc:
- EDID fixes
- Don't handle hotplug events in IRQ handler"
* tag 'drm-fixes-2021-02-05-1' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/nouveau: fix dma syncing warning with debugging on.
drm/amd/display: Decrement refcount of dc_sink before reassignment
drm/amd/display: Free atomic state after drm_atomic_commit
drm/amd/display: Fix dc_sink kref count in emulated_link_detect
drm/amd/display: Release DSC before acquiring
drm/amd/display: Revert "Fix EDID parsing after resume from suspend"
drm/amd/display: Add more Clock Sources to DCN2.1
drm/amd/display: reuse current context instead of recreating one
drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVAL
drm/amdgpu: enable freesync for A+A configs
drm/amd/pm: fill in the data member of v2 gpu metrics table for vangogh
drm/amdgpu/gfx10: update CGTS_TCC_DISABLE and CGTS_USER_TCC_DISABLE register offsets for VGH
drm/amdkfd: fix null pointer panic while free buffer in kfd
drm/amdgpu: fix the issue that retry constantly once the buffer is oversize
drm/i915/dp: Fix LTTPR vswing/pre-emp setting in non-transparent mode
drm/i915/dp: Move intel_dp_set_signal_levels() to intel_dp_link_training.c
drm/i915: Fix the MST PBN divider calculation
drm/dp/mst: Export drm_dp_get_vc_payload_bw()
drm/i915/gem: Drop lru bumping on display unpinning
drm/i915/gt: Close race between enable_breadcrumbs and cancel_breadcrumbs
...
|
|
When iteratively computing a checksum with csum_block_add, track the
offset "pos" to correctly rotate in csum_block_add when offset is odd.
The open coded implementation of skb_copy_and_csum_datagram did this.
With the switch to __skb_datagram_iter calling csum_and_copy_to_iter,
pos was reinitialized to 0 on each call.
Bring back the pos by passing it along with the csum to the callback.
Changes v1->v2
- pass csum value, instead of csump pointer (Alexander Duyck)
Link: https://lore.kernel.org/netdev/20210128152353.GB27281@optiplex/
Fixes: 950fcaecd5cc ("datagram: consolidate datagram copy to iter helpers")
Reported-by: Oliver Graute <oliver.graute@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210203192952.1849843-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Initialize tracing-graph-pause at task creation, not start of
function tracing, to avoid corrupting the pause counter.
- Set "pause-on-trace" for latency tracers as that option breaks their
output (regression).
- Fix the wrong error return for setting kretprobes on future modules
(before they are loaded).
- Fix re-registering the same kretprobe.
- Add missing value check for added RCU variable reload.
* tag 'trace-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracepoint: Fix race between tracing and removing tracepoint
kretprobe: Avoid re-registration of the same kretprobe earlier
tracing/kprobe: Fix to support kretprobe events on unloaded modules
tracing: Use pause-on-trace with the latency tracers
fgraph: Initialize tracing_graph_pause at task creation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.11-rc7, including fixes from bpf and mac80211
trees.
Current release - regressions:
- ip_tunnel: fix mtu calculation
- mlx5: fix function calculation for page trees
Previous releases - regressions:
- vsock: fix the race conditions in multi-transport support
- neighbour: prevent a dead entry from updating gc_list
- dsa: mv88e6xxx: override existent unicast portvec in port_fdb_add
Previous releases - always broken:
- bpf, cgroup: two copy_{from,to}_user() warn_on_once splats for BPF
cgroup getsockopt infra when user space is trying to race against
optlen, from Loris Reiff.
- bpf: add missing fput() in BPF inode storage map update helper
- udp: ipv4: manipulate network header of NATed UDP GRO fraglist
- mac80211: fix station rate table updates on assoc
- r8169: work around RTL8125 UDP HW bug
- igc: report speed and duplex as unknown when device is runtime
suspended
- rxrpc: fix deadlock around release of dst cached on udp tunnel"
* tag 'net-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
net: hsr: align sup_multicast_addr in struct hsr_priv to u16 boundary
net: ipa: fix two format specifier errors
net: ipa: use the right accessor in ipa_endpoint_status_skip()
net: ipa: be explicit about endianness
net: ipa: add a missing __iomem attribute
net: ipa: pass correct dma_handle to dma_free_coherent()
r8169: fix WoL on shutdown if CONFIG_DEBUG_SHIRQ is set
net/rds: restrict iovecs length for RDS_CMSG_RDMA_ARGS
net: mvpp2: TCAM entry enable should be written after SRAM data
net: lapb: Copy the skb before sending a packet
net/mlx5e: Release skb in case of failure in tc update skb
net/mlx5e: Update max_opened_tc also when channels are closed
net/mlx5: Fix leak upon failure of rule creation
net/mlx5: Fix function calculation for page trees
docs: networking: swap words in icmp_errors_use_inbound_ifaddr doc
udp: ipv4: manipulate network header of NATed UDP GRO fraglist
net: ip_tunnel: fix mtu calculation
vsock: fix the race conditions in multi-transport support
net: sched: replaced invalid qdisc tree flush helper in qdisc_replace
ibmvnic: device remove has higher precedence over reset
...
|
|
This function will be needed by the next patch where the driver
calculates the BW based on driver specific parameters, so export it.
At the same time sanitize the function params, passing the more natural
link rate instead of the encoding of the same rate.
v2:
- Fix function documentation. (Lyude)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-1-imre.deak@intel.com
(cherry picked from commit a321fc2b4e60fc1b39517d26c8104351636a6062)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The dev_iommu_priv_get() needs a similar check to
dev_iommu_fwspec_get() to make sure no NULL-ptr is dereferenced.
Fixes: 05a0542b456e1 ("iommu/amd: Store dev_data as device iommu private data")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20210202145419.29143-1-joro@8bytes.org
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=211241
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When executing a tracepoint, the tracepoint's func is dereferenced twice -
in __DO_TRACE() (where the returned pointer is checked) and later on in
__traceiter_##_name where the returned pointer is dereferenced without
checking which leads to races against tracepoint_removal_sync() and
crashes.
This adds a check before referencing the pointer in tracepoint_ptr_deref.
Link: https://lkml.kernel.org/r/20210202072326.120557-1-aik@ozlabs.ru
Cc: stable@vger.kernel.org
Fixes: d25e37d89dd2f ("tracepoint: Optimize using static_call()")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
UDP/IP header of UDP GROed frag_skbs are not updated even after NAT
forwarding. Only the header of head_skb from ip_finish_output_gso ->
skb_gso_segment is updated but following frag_skbs are not updated.
A call path skb_mac_gso_segment -> inet_gso_segment ->
udp4_ufo_fragment -> __udp_gso_segment -> __udp_gso_segment_list
does not try to update UDP/IP header of the segment list but copy
only the MAC header.
Update port, addr and check of each skb of the segment list in
__udp_gso_segment_list. It covers both SNAT and DNAT.
Fixes: 9fd1ff5d2ac7 (udp: Support UDP fraglist GRO/GSO.)
Signed-off-by: Dongseok Yi <dseok.yi@samsung.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Link: https://lore.kernel.org/r/1611962007-80092-1-git-send-email-dseok.yi@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit e5f0e8f8e456 ("net: sched: introduce and use qdisc tree flush/purge helpers")
introduced qdisc tree flush/purge helpers, but erroneously used flush helper
instead of purge helper in qdisc_replace function.
This issue was found in our CI, that tests various qdisc setups by configuring
qdisc and sending data through it. Call of invalid helper sporadically leads
to corruption of vt_tree/cf_tree of hfsc_class that causes kernel oops:
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.11.0-8f6859df #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:rb_insert_color+0x18/0x190
Code: c3 31 c0 c3 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 48 8b 07 48 85 c0 0f 84 05 01 00 00 48 8b 10 f6 c2 01 0f 85 34 01 00 00 <48> 8b 4a 08 49 89 d0 48 39 c1 74 7d 48 85 c9 74 32 f6 01 01 75 2d
RSP: 0018:ffffc900000b8bb0 EFLAGS: 00010246
RAX: ffff8881ef4c38b0 RBX: ffff8881d956e400 RCX: ffff8881ef4c38b0
RDX: 0000000000000000 RSI: ffff8881d956f0a8 RDI: ffff8881d956e4b0
RBP: 0000000000000000 R08: 000000d5c4e249da R09: 1600000000000000
R10: ffffc900000b8be0 R11: ffffc900000b8b28 R12: 0000000000000001
R13: 000000000000005a R14: ffff8881f0905000 R15: ffff8881f0387d00
FS: 0000000000000000(0000) GS:ffff8881f8b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 00000001f4796004 CR4: 0000000000060ee0
Call Trace:
<IRQ>
init_vf.isra.19+0xec/0x250 [sch_hfsc]
hfsc_enqueue+0x245/0x300 [sch_hfsc]
? fib_rules_lookup+0x12a/0x1d0
? __dev_queue_xmit+0x4b6/0x930
? hfsc_delete_class+0x250/0x250 [sch_hfsc]
__dev_queue_xmit+0x4b6/0x930
? ip6_finish_output2+0x24d/0x590
ip6_finish_output2+0x24d/0x590
? ip6_output+0x6c/0x130
ip6_output+0x6c/0x130
? __ip6_finish_output+0x110/0x110
mld_sendpack+0x224/0x230
mld_ifc_timer_expire+0x186/0x2c0
? igmp6_group_dropped+0x200/0x200
call_timer_fn+0x2d/0x150
run_timer_softirq+0x20c/0x480
? tick_sched_do_timer+0x60/0x60
? tick_sched_timer+0x37/0x70
__do_softirq+0xf7/0x2cb
irq_exit+0xa0/0xb0
smp_apic_timer_interrupt+0x74/0x150
apic_timer_interrupt+0xf/0x20
</IRQ>
Fixes: e5f0e8f8e456 ("net: sched: introduce and use qdisc tree flush/purge helpers")
Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru>
Reported-by: Alexander Kuznetsov <wwfq@yandex-team.ru>
Acked-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru>
Acked-by: Dmitry Yakunin <zeil@yandex-team.ru>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20210201200049.299153-1-ovov@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"The rockship rkisp1 driver will be promoted from staging in 5.11.
While not too late, do a few uAPI changes which are needed to better
support its functionalities"
* tag 'media/v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rockchip: rkisp1: extend uapi array sizes
media: rockchip: rkisp1: carry ip version information
media: rockchip: rkisp1: reduce number of histogram grid elements in uapi
media: rkisp1: stats: mask the hist_bins values
media: rkisp1: stats: remove a wrong cast to u8
media: rkisp1: uapi: change hist_bins array type from __u16 to __u32
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
"A single fix for objtool to generate proper unwind info for newer
toolchains which do not generate section symbols anymore. And a
cleanup ontop.
This was originally going to go during the next merge window but
people can already trigger a build error with binutils-2.36 which
doesn't emit section symbols - something which objtool relies on - so
let's expedite it"
* tag 'x86_entry_for_v5.11_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry: Remove put_ret_addr_in_rdi THUNK macro argument
x86/entry: Emit a symbol for register restoring thunk
|
|
Pull NFS client fixes from Trond Myklebust:
- SUNRPC: Handle 0 length opaque XDR object data properly
- Fix a layout segment leak in pnfs_layout_process()
- pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn
- pNFS/NFSv4: Improve rejection of out-of-order layouts
- pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()
* tag 'nfs-for-5.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Handle 0 length opaque XDR object data properly
SUNRPC: Move simple_get_bytes and simple_get_netobj into private header
pNFS/NFSv4: Improve rejection of out-of-order layouts
pNFS/NFSv4: Update the layout barrier when we schedule a layoutreturn
pNFS/NFSv4: Try to return invalid layout in pnfs_layout_process()
pNFS/NFSv4: Fix a layout segment leak in pnfs_layout_process()
|
|
When MSI_FLAG_ACTIVATE_EARLY is set (which is the case for PCI),
__msi_domain_alloc_irqs() performs the activation of the interrupt (which
in the case of PCI results in the endpoint being programmed) as soon as the
interrupt is allocated.
But it appears that this is only done for the first vector, introducing an
inconsistent behaviour for PCI Multi-MSI.
Fix it by iterating over the number of vectors allocated to each MSI
descriptor. This is easily achieved by introducing a new
"for_each_msi_vector" iterator, together with a tiny bit of refactoring.
Fixes: f3b0946d629c ("genirq/msi: Make sure PCI MSIs are activated early")
Reported-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210123122759.1781359-1-maz@kernel.org
|
|
Fix kprobe_on_func_entry() returns error code instead of false so that
register_kretprobe() can return an appropriate error code.
append_trace_kprobe() expects the kprobe registration returns -ENOENT
when the target symbol is not found, and it checks whether the target
module is unloaded or not. If the target module doesn't exist, it
defers to probe the target symbol until the module is loaded.
However, since register_kretprobe() returns -EINVAL instead of -ENOENT
in that case, it always fail on putting the kretprobe event on unloaded
modules. e.g.
Kprobe event:
/sys/kernel/debug/tracing # echo p xfs:xfs_end_io >> kprobe_events
[ 16.515574] trace_kprobe: This probe might be able to register after target module is loaded. Continue.
Kretprobe event: (p -> r)
/sys/kernel/debug/tracing # echo r xfs:xfs_end_io >> kprobe_events
sh: write error: Invalid argument
/sys/kernel/debug/tracing # cat error_log
[ 41.122514] trace_kprobe: error: Failed to register probe event
Command: r xfs:xfs_end_io
^
To fix this bug, change kprobe_on_func_entry() to detect symbol lookup
failure and return -ENOENT in that case. Otherwise it returns -EINVAL
or 0 (succeeded, given address is on the entry).
Link: https://lkml.kernel.org/r/161176187132.1067016.8118042342894378981.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: 59158ec4aef7 ("tracing/kprobes: Check the probe on unloaded module correctly")
Reported-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes including fixes from can, xfrm, wireless,
wireless-drivers and netfilter trees. Nothing scary, Intel
WiFi-related fixes seemed most notable to the users.
Current release - regressions:
- dsa: microchip: ksz8795: fix KSZ8794 port map again to program the
CPU port correctly
Current release - new code bugs:
- iwlwifi: pcie: reschedule in long-running memory reads
Previous releases - regressions:
- iwlwifi: dbg: don't try to overwrite read-only FW data
- iwlwifi: provide gso_type to GSO packets
- octeontx2: make sure the buffer is 128 byte aligned
- tcp: make TCP_USER_TIMEOUT accurate for zero window probes
- xfrm: fix wraparound in xfrm_policy_addr_delta()
- xfrm: fix oops in xfrm_replay_advance_bmp due to a race between
CPUs in presence of packet reorder
- tcp: fix TLP timer not set when CA_STATE changes from DISORDER to
OPEN
- wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Previous releases - always broken:
- igc: fix link speed advertising
- stmmac: configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA
addressing
- team: protect features update by RCU to avoid deadlock
- xfrm: fix disable_xfrm sysctl when used on xfrm interfaces
themselves
- fec: fix temporary RMII clock reset on link up
- can: dev: prevent potential information leak in can_fill_info()
Misc:
- mrp: fix bad packing of MRP test packet structures
- uapi: fix big endian definition of ipv6_rpl_sr_hdr
- add David Ahern to IPv4/IPv6 maintainers"
* tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
rxrpc: Fix memory leak in rxrpc_lookup_local
mlxsw: spectrum_span: Do not overwrite policer configuration
selftests: forwarding: Specify interface when invoking mausezahn
stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing
net: usb: cdc_ether: added support for Thales Cinterion PLSx3 modem family.
ibmvnic: Ensure that CRQ entry read are correctly ordered
MAINTAINERS: add missing header for bonding
net: decnet: fix netdev refcount leaking on error path
net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP
can: dev: prevent potential information leak in can_fill_info()
net: fec: Fix temporary RMII clock reset on link up
net: lapb: Add locking to the lapb module
team: protect features update by RCU to avoid deadlock
MAINTAINERS: add David Ahern to IPv4/IPv6 maintainers
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
...
|
|
Pull rdma fixes from Jason Gunthorpe:
"Several recent regressions and some bug fixes:
- Typo corrupting the max_recv_sge for cxgb4
- Regression from re-using kernel enums as a HW AbI in vmw_pvrdma
- Sleeping inside a spinlock in hns
- Revert the attempt to fix devlink deadlocks as the fix is more buggy
- Typo in sysfs_emit_at conversions
- Revert the removal of VLAN support in rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
Revert "RDMA/rxe: Remove VLAN code leftovers from RXE"
RDMA/usnic: Fix misuse of sysfs_emit_at
Revert "RDMA/mlx5: Fix devlink deadlock on net namespace deletion"
RDMA/hns: Use mutex instead of spinlock for ida allocation
RDMA/vmw_pvrdma: Fix network_hdr_type reported in WC
RDMA/cxgb4: Fix the reported max_recv_sge value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a V4L2 core regression at videobuf2 when checking for single-plane
dmabuf
- a change at uAPI header v4l2-subdev.h, fixing a breakage as BIT()
macro is not available in userspace
- fix some regressions at RC core due to the usage of microseconds
everywhere on it
- a fix for a race condition at RC core
- a rename on a newly-introduced kAPI symbol (v4l2_get_link_rate),
currently used only by a single driver
- Regression fixes for rcar-vin, cedrus, ite-cir, hantro, css, venus,
and cec drivers.
* tag 'media/v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hantro: Fix reset_raw_fmt initialization
media: cec: add stm32 driver
media: cedrus: Fix H264 decoding
media: v4l2-subdev.h: BIT() is not available in userspace
media: Revert "media: videobuf2: Fix length check for single plane dmabuf queueing"
media: rc: ite-cir: fix min_timeout calculation
media: venus: core: Fix platform driver shutdown
media: rc: fix timeout handling after switch to microsecond durations
media: v4l: common: Fix naming of v4l2_get_link_rate
media: rcar-vin: fix return, use ret instead of zero
media: ccs: Get static data version minor correctly
media: ccs-pll: Fix link frequency for C-PHY
media: rc: ensure that uevent can be read directly after rc device register
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Although the incoming fixes haven't settled down yet, all changes here
are small and mostly device-specific fixes, so nothing look worrisome.
- Yet another USB-audio regression fixes
- HD-audio ID fix and device-specific quirks
- SOF Intel / SoundWire fixes including topology
- ASoC Qualcomm and Mediatek fixes"
* tag 'sound-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda/via: Apply the workaround generically for Clevo machines
ASoC: Intel: sof_sdw: set proper flags for Dell TGL-H SKU 0A5E
ASoC: qcom: lpass: Fix out-of-bounds DAI ID lookup
ASoC: mediatek: mt8192-mt6359: add format constraints for RT5682
ASoC: ak4458: correct reset polarity
ASoC: SOF: SND_INTEL_DSP_CONFIG dependency
ASoC: SOF: Intel: soundwire: fix select/depend unmet dependencies
ALSA: hda: intel-dsp-config: add PCI id for TGL-H
ALSA: usb-audio: workaround for iface reset issue
ALSA: pcm: One more dependency for hw constraints
ALSA: hda/realtek: Enable headset of ASUS B1400CEPE with ALC256
ASoC: Intel: Skylake: Zero snd_ctl_elem_value
ASoC: Intel: Skylake: skl-topology: Fix OOPs ib skl_tplg_complete
ASoC: qcom: Fix number of HDMI RDMA channels on sc7180
ASoC: mediatek: mt8183-da7219: ignore TDM DAI link by default
ASoC: mediatek: mt8183-mt6358: ignore TDM DAI link by default
ASoC: topology: Properly unregister DAI on removal
ASoC: topology: Fix memory corruption in soc_tplg_denum_create_values()
ASoC: qcom: lpass-ipq806x: fix bitwidth regmap field
ASoC: AMD Renoir - refine DMI entries for some Lenovo products
...
|
|
Later variants of the rkisp1 block use more entries in some arrays:
RKISP1_CIF_ISP_AE_MEAN_MAX 25 -> 81
RKISP1_CIF_ISP_HIST_BIN_N_MAX 16 -> 32
RKISP1_CIF_ISP_GAMMA_OUT_MAX_SAMPLES 17 -> 34
RKISP1_CIF_ISP_HISTOGRAM_WEIGHT_GRIDS_SIZE 25 -> 81
and we can still extend the uapi during the 5.11-rc cycle, so do that
now to be on the safe side.
V10 and V11 only need the smaller sizes, while V12 and V13 needed
the larger sizes.
When adding the bigger sizes make sure, values filled from hardware
values and transmitted to userspace don't leak kernel data by zeroing
them beforehand.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The IP block evolved from its rk3288/rk3399 base and the vendor
designates them with a numerical version. rk3399 for example
is designated V10 probably meaning V1.0.
There doesn't seem to be an actual version register we could read that
information from, so allow the match_data to carry that information
for future differentiation.
Also carry that information in the hw_revision field of the media-
controller API, so that userspace also has access to that.
The added versions are:
- V10: at least rk3288 + rk3399
- V11: seemingly unused as of now, but probably appeared in some soc
- V12: at least rk3326 + px30
- V13: at least rk1808
[fix checkpatch warning don't use multiple blank lines]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The uapi right now specifies an array size of 28 but the actual number
of elements is only 25 with the last 3 being unused.
Reduce the array size to the correct number of elements and change
the params code to iterate the array 25 times.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Each entry in the array is a 20 bits value composed of 16 bits unsigned
integer and 4 bits fractional part. So the type should change to __u32.
In addition add a documentation of how the measurements are done.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Honor stateful expressions defined in the set from the dynset
extension. The set definition provides a stateful expression
that must be used by the dynset expression in case it is specified.
2) Missing timeout extension in the set element in the dynset
extension leads to inconsistent ruleset listing, not allowing
the user to restore timeout and expiration on ruleset reload.
3) Do not dump the stateful expression from the dynset extension
if it coming from the set definition.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nft_dynset: dump expressions when set definition contains no expressions
netfilter: nft_dynset: add timeout extension to template
netfilter: nft_dynset: honor stateful expressions in set definition
====================
Link: https://lore.kernel.org/r/20210127132512.5472-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the lapb module, the timers may run concurrently with other code in
this module, and there is currently no locking to prevent the code from
racing on "struct lapb_cb". This patch adds locking to prevent racing.
1. Add "spinlock_t lock" to "struct lapb_cb"; Add "spin_lock_bh" and
"spin_unlock_bh" to APIs, timer functions and notifier functions.
2. Add "bool t1timer_stop, t2timer_stop" to "struct lapb_cb" to make us
able to ask running timers to abort; Modify "lapb_stop_t1timer" and
"lapb_stop_t2timer" to make them able to abort running timers;
Modify "lapb_t2timer_expiry" and "lapb_t1timer_expiry" to make them
abort after they are stopped by "lapb_stop_t1timer", "lapb_stop_t2timer",
and "lapb_start_t1timer", "lapb_start_t2timer".
3. Let lapb_unregister wait for other API functions and running timers
to stop.
4. The lapb_device_event function calls lapb_disconnect_request. In
order to avoid trying to hold the lock twice, add a new function named
"__lapb_disconnect_request" which assumes the lock is held, and make
it called by lapb_disconnect_request and lapb_device_event.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20210126040939.69995-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The main thing here is a change to make sure that we don't try to
double resolve the supply of a regulator if we have two probes going
on simultaneously, plus an incremental fix on top of that to resolve a
lockdep issue it introduced.
There's also a patch from Dmitry Osipenko adding stubs for some
functions to avoid build issues in consumers in some configurations"
* tag 'regulator-fix-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix lockdep warning resolving supplies
regulator: consumer: Add missing stubs to regulator/consumer.h
regulator: core: avoid regulator_resolve_supply() race condition
|
|
The BIT macro is not available in userspace, so replace BIT(0) by
0x00000001.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 6446ec6cbf46 ("media: v4l2-subdev: add VIDIOC_SUBDEV_QUERYCAP ioctl")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
