| Age | Commit message (Collapse) | Author |
|---|
|
Introduce new netlink attributes for SET_PHY_ATTRS:
* CSMA minimal backoff exponent
* CSMA maximal backoff exponent
* CSMA retry limit
* frame retransmission limit
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.
Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new fields to struct tcp_info, to report sk_pacing_rate
and sk_max_pacing_rate to monitoring applications, as ss from iproute2.
User exported fields are 64bit, even if kernel is currently using 32bit
fields.
lpaa5:~# ss -i
..
skmem:(r0,rb357120,t0,tb2097152,f1584,w1980880,o0,bl0) ts sack cubic
wscale:6,6 rto:400 rtt:0.875/0.75 mss:1448 cwnd:1 ssthresh:12 send
13.2Mbps pacing_rate 3336.2Mbps unacked:15 retrans:1/5448 lost:15
rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Ethernet MACs are connected to a MoCA PHY which will handle the
low-level job of sending Ethernet frames on the coaxial cable, these
Ethernet MACs need to know about it to be properly configured.
Add a new PHY mode "moca" and update the Device Tree parsing logic to
look for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 684bad110757 "tcp: use PRR to reduce cwin in CWR state" removed all
calls to min_cwnd, so we can safely remove it.
Also, remove tcp_reno_min_cwnd because it was only used for min_cwnd.
Signed-off-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an action is bonnd to a filter, there is no point to
remove it outside. Currently we just silently decrease the refcnt,
we should reject this explicitly with EPERM.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For bindcnt and refcnt etc., they are common for all actions,
not need to repeat such operations for their own, they can be unified
now. Actions just need to do its specific cleanup if needed.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we can totally hide it from modules. tcf_hash_*() API's
will operate on struct tc_action, modules don't need to care about
the details.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a boolean property which indicates if the PHY has had any fixup
routine ran on it. We are later going to use that boolean to expose it
as a sysfs property to help troubleshooting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_phy_mode() uses a local array to map phy_interface_t values from
include/linux/net/phy.h to a string which is read from the 'phy-mode' or
'phy-connection-type' property. In preparation for exposing the PHY
interface mode through sysfs, perform the following:
- mode phy_modes from drivers/of/of_net.c to include/linux/phy.h such
that it is right below the phy_interface_t enum
- make it a static inline function returning the string such that we can
use it by just including include/linux/net/phy.h
- add a PHY_INTERFACE_MODE_MAX enum value to guard the iteration in
of_get_phy_mode()
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs out there can be very quirky with respect to how they would
report the auto-negotiation is completed. Allow drivers to override the
generic aneg_done() implementation by providing their own.
Since not all drivers have been updated yet to use genphy_aneg_done() as
aneg_done() callback, we explicitely check that this callback is valid
before calling into it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for allowing PHY drivers to potentially override their
auto-negotiation done callback, move the contents of phy_aneg_done() to
genphy_aneg_done() since that function really is the generic
implementation based on the BMSR_ANEGCOMPLETE status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A colon almost unavoidably starts a new section. The script should be
changed to provide a way to avoid this, but for now reword the
comments to avoid using colons.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel-doc script does not tolerate the macro definition in between.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Various ethtool command structures are declared with zero-length array
at the end which are intended to be variable-length in userland
(relying on lack of compiler bounds checking). However, in the kernel
the structure and array are always allocated and passed to driver
operations separately. Make that explicit.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the inline comments to kernel-doc format.
Explicitly specify that non-zero autoneg is an error if link
autonegotiation is disabled.
Specify that pause capabilities should be advertised dependent on link
autonegotiation, not the autoneg flag here. There is no way to
opt-out of pause frame autonegotiation, and this improves behaviour
when the link partner is configured to follow pause frame
autonegotiation and our interface is not.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the inline comments (and some others below) with a full
explanation of the semantics, in kernel-doc format. Specify which
strings may be empty. Document the relationship with other commands.
Replace the 'deprecation' of some fields with a proper explanation of
the conversion to generalised string sets, as userland programs may
not be able to assume that ETHTOOL_GSSET_INFO is available.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ethtool_cmd has very limited documentation; it contains
several obscure or obsolete fields and several with non-obvious
interpretation.
Replace the inline comments (and some others below) with a full
explanation of the semantics as well as I understand them, in
kernel-doc format. Formally deprecate some fields that seem to be of
historical use only.
Extend the comment about 32/64-bit compatibility to cover all
ethtool structures.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
|
|
Use what we already do for arch_disable_smp_support() to fix these:
arch/x86/kernel/smpboot.c:1155:6: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
arch/x86/kernel/smpboot.c:1160:6: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
kernel/cpu.c:512:13: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
kernel/cpu.c:516:13: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder. The O_SYNC bug is fairly
old..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a kmap leak in virtio_console
fix O_SYNC|O_APPEND syncing the wrong range on write()
|
|
from net/ipx/af_ipx.c
Move prototype declaration of function to header file
include/net/net_namespace.h from net/ipx/af_ipx.c because they are used
by more than one file.
This eliminates the following warning in net/ipx/sysctl_net_ipx.c:
net/ipx/sysctl_net_ipx.c:33:6: warning: no previous prototype for ‘ipx_register_sysctl’ [-Wmissing-prototypes]
net/ipx/sysctl_net_ipx.c:38:6: warning: no previous prototype for ‘ipx_unregister_sysctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipx/af_ipx.c
Move prototype declarations of function to header file
include/net/datalink.h from net/ipx/af_ipx.c because they are used by
more than one file.
This eliminates the following warning in net/ipx/pe2.c:
net/ipx/pe2.c:20:24: warning: no previous prototype for ‘make_EII_client’ [-Wmissing-prototypes]
net/ipx/pe2.c:32:6: warning: no previous prototype for ‘destroy_EII_client’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipx/af_ipx.c
Move prototype declaration of functions to header file include/net/ipx.h
from net/ipx/af_ipx.c because they are used by more than one file.
This eliminates the following warning in
net/ipx/ipx_route.c:33:19: warning: no previous prototype for ‘ipxrtr_lookup’ [-Wmissing-prototypes]
net/ipx/ipx_route.c:52:5: warning: no previous prototype for ‘ipxrtr_add_route’ [-Wmissing-prototypes]
net/ipx/ipx_route.c:94:6: warning: no previous prototype for ‘ipxrtr_del_routes’ [-Wmissing-prototypes]
net/ipx/ipx_route.c:149:5: warning: no previous prototype for ‘ipxrtr_route_skb’ [-Wmissing-prototypes]
net/ipx/ipx_route.c:171:5: warning: no previous prototype for ‘ipxrtr_route_packet’ [-Wmissing-prototypes]
net/ipx/ipx_route.c:261:5: warning: no previous prototype for ‘ipxrtr_ioctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move prototype definition of function to header file include/net/ipx.h
from net/ipx/ipx_route.c because they are used by more than one file.
This eliminates the following warning from net/ipx/af_ipx.c:
net/ipx/af_ipx.c:193:23: warning: no previous prototype for ‘ipxitf_find_using_net’ [-Wmissing-prototypes]
net/ipx/af_ipx.c:577:5: warning: no previous prototype for ‘ipxitf_send’ [-Wmissing-prototypes]
net/ipx/af_ipx.c:1219:8: warning: no previous prototype for ‘ipx_cksum’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/decnet/af_decnet.c
Move prototype declaration of functions to header file include/net/dn.h
from net/decnet/af_decnet.c because they are used by more than one file.
This eliminates the following warning in net/decnet/af_decnet.c:
net/decnet/sysctl_net_decnet.c:354:6: warning: no previous prototype for ‘dn_register_sysctl’ [-Wmissing-prototypes]
net/decnet/sysctl_net_decnet.c:359:6: warning: no previous prototype for ‘dn_unregister_sysctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
decnet/af_decnet.c
Move prototype declaration of functions to header file include/net/dn_route.h
from net/decnet/af_decnet.c because it is used by more than one file.
This eliminates the following warning in net/decnet/dn_route.c:
net/decnet/dn_route.c:629:5: warning: no previous prototype for ‘dn_route_rcv’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/nftables/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes, mostly nftables
fixes, most relevantly they are:
* Fix a crash in the h323 conntrack NAT helper due to expectation list
corruption, from Alexey Dobriyan.
* A couple of RCU race fixes for conntrack, one manifests by hitting BUG_ON
in nf_nat_setup_info() and the destroy path, patches from Andrey Vagin and
me.
* Dump direction attribute in nft_ct only if it is set, from Arturo
Borrero.
* Fix IPVS bug in its own connection tracking system that may lead to
copying only 4 bytes of the IPv6 address when initializing the
ip_vs_conn object, from Michal Kubecek.
* Fix -EBUSY errors in nftables when deleting the rules, chain and tables
in a row due mixture of asynchronous and synchronous object releasing,
from me.
* Three fixes for the nf_tables set infrastructure when using intervals and
mappings, from me.
* Four patches to fixing the nf_tables log, reject and ct expressions from
the new inet table, from Patrick McHardy.
* Fix memory overrun in the map that is used to dynamically allocate names
from anonymous sets, also from Patrick.
* Fix a potential oops if you dump a set with NFPROTO_UNSPEC and a table
name, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It actually goes back to 2004 ([PATCH] Concurrent O_SYNC write support)
when sync_page_range() had been introduced; generic_file_write{,v}() correctly
synced
pos_after_write - written .. pos_after_write - 1
but generic_file_aio_write() synced
pos_before_write .. pos_before_write + written - 1
instead. Which is not the same thing with O_APPEND, obviously.
A couple of years later correct variant had been killed off when
everything switched to use of generic_file_aio_write().
All users of generic_file_aio_write() are affected, and the same bug
has been copied into other instances of ->aio_write().
The fix is trivial; the only subtle point is that generic_write_sync()
ought to be inlined to avoid calculations useless for the majority of
calls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Quite a varied little collection of fixes. Most of them are
relatively small or isolated; the biggest one is Mel Gorman's fixes
for TLB range flushing.
A couple of AMD-related fixes (including not crashing when given an
invalid microcode image) and fix a crash when compiled with gcov"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Unify valid container checks
x86, hweight: Fix BUG when booting with CONFIG_GCOV_PROFILE_ALL=y
x86/efi: Allow mapping BGRT on x86-32
x86: Fix the initialization of physnode_map
x86, cpu hotplug: Fix stack frame warning in check_irq_vectors_for_cpu_disable()
x86/intel/mid: Fix X86_INTEL_MID dependencies
arch/x86/mm/srat: Skip NUMA_NO_NODE while parsing SLIT
mm, x86: Revisit tlb_flushall_shift tuning for page flushes except on IvyBridge
x86: mm: change tlb_flushall_shift for IvyBridge
x86/mm: Eliminate redundant page table walk during TLB range flushing
x86/mm: Clean up inconsistencies when flushing TLB ranges
mm, x86: Account for TLB flushes only when debugging
x86/AMD/NB: Fix amd_set_subcaches() parameter type
x86/quirks: Add workaround for AMD F16h Erratum792
x86, doc, kconfig: Fix dud URL for Microcode data
|
|
* Avoid WARN_ON() when mapping BGRT on Baytrail (EFI 32-bit).
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Commit cfd280c91253 ("net: sync some IP headers with glibc") changed a set of
define's to an enum (with no explanation why) which introduced a bug
in module mip6 where aliases are generated using the IPPROTO_* defines;
mip6 doesn't load if require_module called with the aliases from
xfrm_get_type().
Reverting this change back to define's to fix the aliases.
modinfo mip6 (before this change)
alias: xfrm-type-10-IPPROTO_DSTOPTS
alias: xfrm-type-10-IPPROTO_ROUTING
modinfo mip6 (after this change)
alias: xfrm-type-10-43
alias: xfrm-type-10-60
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
