| Age | Commit message (Collapse) | Author |
|---|
|
Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.
X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.
Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:
- Store it in the irq descriptors affinity mask
- Update the effective affinity to reflect that so user space has
a consistent view
- Don't call into the irq chip driver
This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.
Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.
For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.
Remove the X86 workaround as it is not longer required.
Fixes: 02edee152d6e ("x86/apic/vector: Ignore set_affinity call for inactive interrupts")
Reported-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ali Saidi <alisaidi@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com
Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A few new drivers for the Loongson MIPS platform (HTVEC, PIC, MSI)
- A cleanup of the __irq_domain_add() API
- A cleanup of the IRQ simulator to actually use some of
the irq infrastructure
- Some fixes for the Sifive PLIC when used in a multi-controller
context
- Fixes for the GICv3 ITS to spread interrupts according to the
load of each CPU, and to honor managed interrupts
- Numerous cleanups and documentation fixes
|
|
irq_data_get_irq_chip() can return NULL, however it is expected that this
never happens. If a buggy driver leads to NULL being returned from
irq_data_get_irq_chip(), warn about it instead of crashing the machine.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-arm-kernel@lists.infradead.org
|
|
In some cases we need to have an IRQ domain created out of software node.
One of such cases is DesignWare GPIO driver when it's instantiated from
half-baked ACPI table (alas, we can't fix it for devices which are few years
on market) and thus using software nodes to quirk this. But the driver
is using IRQ domains based on per GPIO port firmware nodes, which are in
the above case software ones. This brings a warning message to be printed
[ 73.957183] irq: Invalid fwnode type for irqdomain
and creates an anonymous IRQ domain without a debugfs entry.
Allowing software nodes to be valid for IRQ domains rids us of the warning
and debugs gets correctly populated.
% ls -1 /sys/kernel/debug/irq/domains/
...
intel-quark-dw-apb-gpio:portA
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[maz: refactored commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200520164927.39090-3-andriy.shevchenko@linux.intel.com
|
|
Now that __irq_domain_add() is able to better deals with generic
fwnodes, there is no need to special-case ACPI anymore.
Get rid of the special treatment for ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200520164927.39090-2-andriy.shevchenko@linux.intel.com
|
|
__irq_domain_add() relies in some places on the fact that the fwnode
can be only of type OF. This prevents refactoring of the code to support
other types of fwnode. Make it less OF-dependent by switching it
to use the fwnode directly where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200520164927.39090-1-andriy.shevchenko@linux.intel.com
|
|
The interrupt simulator API exposes a lot of custom data structures and
functions and doesn't reuse the interfaces already exposed by the irq
subsystem. This patch tries to address it.
We hide all the simulator-related data structures from users and instead
rely on the well-known irq domain. When creating the interrupt simulator
the user receives a pointer to a newly created irq_domain and can use it
to create mappings for simulated interrupts.
It is also possible to pass a handle to fwnode when creating the simulator
domain and retrieve it using irq_find_matching_fwnode().
The irq_sim_fire() function is dropped as well. Instead we implement the
irq_get/set_irqchip_state interface.
We modify the two modules that use the simulator at the same time as
adding these changes in order to reduce the intermediate bloat that would
result when trying to migrate the drivers in separate patches.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for IIO
Link: https://lore.kernel.org/r/20200514083901.23445-3-brgl@bgdev.pl
|
|
irq_domain_reset_irq_data() doesn't modify the parent data, so it can be
made available even if irq domain hierarchy is not being built. We'll
subsequently use it in irq_sim code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200514083901.23445-2-brgl@bgdev.pl
|
|
Now that all the users of setup_irq() & remove_irq() have been replaced by
request_irq() & free_irq() respectively, delete them.
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lkml.kernel.org/r/0aa8771ada1ac8e1312f6882980c9c08bd023148.1585320721.git.afzal.mohd.ma@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 entry code updates from Thomas Gleixner:
- Convert the 32bit syscalls to be pt_regs based which removes the
requirement to push all 6 potential arguments onto the stack and
consolidates the interface with the 64bit variant
- The first small portion of the exception and syscall related entry
code consolidation which aims to address the recently discovered
issues vs. RCU, int3, NMI and some other exceptions which can
interrupt any context. The bulk of the changes is still work in
progress and aimed for 5.8.
- A few lockdep namespace cleanups which have been applied into this
branch to keep the prerequisites for the ongoing work confined.
* tag 'x86-entry-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
x86/entry: Fix build error x86 with !CONFIG_POSIX_TIMERS
lockdep: Rename trace_{hard,soft}{irq_context,irqs_enabled}()
lockdep: Rename trace_softirqs_{on,off}()
lockdep: Rename trace_hardirq_{enter,exit}()
x86/entry: Rename ___preempt_schedule
x86: Remove unneeded includes
x86/entry: Drop asmlinkage from syscalls
x86/entry/32: Enable pt_regs based syscalls
x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments
x86/entry/32: Rename 32-bit specific syscalls
x86/entry/32: Clean up syscall_32.tbl
x86/entry: Remove ABI prefixes from functions in syscall tables
x86/entry/64: Add __SYSCALL_COMMON()
x86/entry: Remove syscall qualifier support
x86/entry/64: Remove ptregs qualifier from syscall table
x86/entry: Move max syscall number calculation to syscallhdr.sh
x86/entry/64: Split X32 syscall table into its own file
x86/entry/64: Move sys_ni_syscall stub to common.c
x86/entry/64: Use syscall wrappers for x32_rt_sigreturn
x86/entry: Refactor SYS_NI macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
|
|
The handling of notify->work did not properly maintain notify->kref in two
cases:
1) where the work was already scheduled, another irq_set_affinity_locked()
would get the ref and (no-op-ly) schedule the work. Thus when
irq_affinity_notify() ran, it would drop the original ref but not the
additional one.
2) when cancelling the (old) work in irq_set_affinity_notifier(), if there
was outstanding work a ref had been got for it but was never put.
Fix both by checking the return values of the work handling functions
(schedule_work() for (1) and cancel_work_sync() for (2)) and put the
extra ref if the return value indicates preexisting work.
Fixes: cd7eab44e994 ("genirq: Add IRQ affinity notifiers")
Fixes: 59c39840f5ab ("genirq: Prevent use-after-free and work list corruption")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Link: https://lkml.kernel.org/r/24f5983f-2ab5-e83a-44ee-a45b5f9300f5@solarflare.com
|
|
Extend lockdep to validate lock wait-type context.
The current wait-types are:
LD_WAIT_FREE, /* wait free, rcu etc.. */
LD_WAIT_SPIN, /* spin loops, raw_spinlock_t etc.. */
LD_WAIT_CONFIG, /* CONFIG_PREEMPT_LOCK, spinlock_t etc.. */
LD_WAIT_SLEEP, /* sleeping locks, mutex_t etc.. */
Where lockdep validates that the current lock (the one being acquired)
fits in the current wait-context (as generated by the held stack).
This ensures that there is no attempt to acquire mutexes while holding
spinlocks, to acquire spinlocks while holding raw_spinlocks and so on. In
other words, its a more fancy might_sleep().
Obviously RCU made the entire ordeal more complex than a simple single
value test because RCU can be acquired in (pretty much) any context and
while it presents a context to nested locks it is not the same as it
got acquired in.
Therefore its necessary to split the wait_type into two values, one
representing the acquire (outer) and one representing the nested context
(inner). For most 'normal' locks these two are the same.
[ To make static initialization easier we have the rule that:
.outer == INV means .outer == .inner; because INV == 0. ]
It further means that its required to find the minimal .inner of the held
stack to compare against the outer of the new lock; because while 'normal'
RCU presents a CONFIG type to nested locks, if it is taken while already
holding a SPIN type it obviously doesn't relax the rules.
Below is an example output generated by the trivial test code:
raw_spin_lock(&foo);
spin_lock(&bar);
spin_unlock(&bar);
raw_spin_unlock(&foo);
[ BUG: Invalid wait context ]
-----------------------------
swapper/0/1 is trying to lock:
ffffc90000013f20 (&bar){....}-{3:3}, at: kernel_init+0xdb/0x187
other info that might help us debug this:
1 lock held by swapper/0/1:
#0: ffffc90000013ee0 (&foo){+.+.}-{2:2}, at: kernel_init+0xd1/0x187
The way to read it is to look at the new -{n,m} part in the lock
description; -{3:3} for the attempted lock, and try and match that up to
the held locks, which in this case is the one: -{2,2}.
This tells that the acquiring lock requires a more relaxed environment than
presented by the lock stack.
Currently only the normal locks and RCU are converted, the rest of the
lockdep users defaults to .inner = INV which is ignored. More conversions
can be done when desired.
The check for spinlock_t nesting is not enabled by default. It's a separate
config option for now as there are known problems which are currently
addressed. The config option allows to identify these problems and to
verify that the solutions found are indeed solving them.
The config switch will be removed and the checks will permanently enabled
once the vast majority of issues has been addressed.
[ bigeasy: Move LD_WAIT_FREE,… out of CONFIG_LOCKDEP to avoid compile
failure with CONFIG_DEBUG_SPINLOCK + !CONFIG_LOCKDEP]
[ tglx: Add the config option ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113242.427089655@linutronix.de
|
|
irq_domain_alloc_irqs_hierarchy() has 3 call sites in the compilation unit
but only one of them checks for the pointer which is being dereferenced
inside the called function. Move the check into the function. This allows
for catching the error instead of the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at 0x0
LR is at gpiochip_hierarchy_irq_domain_alloc+0x11f/0x140
...
[<c06c23ff>] (gpiochip_hierarchy_irq_domain_alloc)
[<c0462a89>] (__irq_domain_alloc_irqs)
[<c0462dad>] (irq_create_fwspec_mapping)
[<c06c2251>] (gpiochip_to_irq)
[<c06c1c9b>] (gpiod_to_irq)
[<bf973073>] (gpio_irqs_init [gpio_irqs])
[<bf974048>] (gpio_irqs_exit+0xecc/0xe84 [gpio_irqs])
Code: bad PC value
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200306174720.82604-1-alexander.sverdlin@nokia.com
|
|
Error injection mechanisms need a half ways safe way to inject interrupts as
invoking generic_handle_irq() or the actual device interrupt handler
directly from e.g. a debugfs write is not guaranteed to be safe.
On x86 generic_handle_irq() is unsafe due to the hardware trainwreck which
is the base of x86 interrupt delivery and affinity management.
Move the irq debugfs injection code into a separate function which can be
used by error injection code as well.
The implementation prevents at least that state is corrupted, but it cannot
close a very tiny race window on x86 which might result in a stale and not
serviced device interrupt under very unlikely circumstances.
This is explicitly for debugging and testing and not for production use or
abuse in random driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.990928309@linutronix.de
|
|
The code sets IRQS_REPLAY unconditionally whether the resend happens or
not. That doesn't have bad side effects right now, but inconsistent state
is always a latent source of problems.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.882129117@linutronix.de
|
|
In preparation for an interrupt injection interface which can be used
safely by error injection mechanisms. e.g. PCI-E/ AER, add a return value
to check_irq_resend() so errors can be propagated to the caller.
Split out the software resend code so the ugly #ifdef in check_irq_resend()
goes away and the whole thing becomes readable.
Fix up the caller in debugfs. The caller in irq_startup() does not care
about the return value as this is unconditionally invoked for all
interrupts and the resend is best effort anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.775200917@linutronix.de
|
|
In general calling generic_handle_irq() with interrupts disabled from non
interrupt context is harmless. For some interrupt controllers like the x86
trainwrecks this is outright dangerous as it might corrupt state if an
interrupt affinity change is pending.
Add infrastructure which allows to mark interrupts as unsafe and catch such
usage in generic_handle_irq().
Reported-by: sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.590923677@linutronix.de
|
|
Interrupts cannot be injected when the interrupt is not activated and when
a replay is already in progress.
Fixes: 536e2e34bd00 ("genirq/debugfs: Triggering of interrupts from userspace")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200306130623.500019114@linutronix.de
|
|
The function got renamed at some point, but the kernel-doc was not updated.
Signed-off-by: luanshi <zhangliguang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1583200125-58806-1-git-send-email-zhangliguang@linux.alibaba.com
|
|
Qian Cai reported that the WARN_ON() in the x86/msi affinity setting code,
which catches cases where the affinity setting is not done on the CPU which
is the current target of the interrupt, triggers during CPU hotplug stress
testing.
It turns out that the warning which was added with the commit addressing
the MSI affinity race unearthed yet another long standing bug.
If user space writes a bogus affinity mask, i.e. it contains no online CPUs,
then it calls irq_select_affinity_usr(). This was introduced for ALPHA in
eee45269b0f5 ("[PATCH] Alpha: convert to generic irq framework (generic part)")
and subsequently made available for all architectures in
18404756765c ("genirq: Expose default irq affinity mask (take 3)")
which introduced the circumvention of the affinity setting restrictions for
interrupt which cannot be moved in process context.
The whole exercise is bogus in various aspects:
1) If the interrupt is already started up then there is absolutely
no point to honour a bogus interrupt affinity setting from user
space. The interrupt is already assigned to an online CPU and it
does not make any sense to reassign it to some other randomly
chosen online CPU.
2) If the interupt is not yet started up then there is no point
either. A subsequent startup of the interrupt will invoke
irq_setup_affinity() anyway which will chose a valid target CPU.
So the only correct solution is to just return -EINVAL in case user space
wrote an affinity mask which does not contain any online CPUs, except for
ALPHA which has it's own magic sauce for this.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Qian Cai <cai@lca.pw>
Link: https://lkml.kernel.org/r/878sl8xdbm.fsf@nanos.tec.linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
|
|
There's some confusion around if an irq that's disabled with disable_irq()
can still wake the system from sleep states such as "suspend to RAM".
Clarify this in the kernel documentation for irq_set_irq_wake() so that
it's clear that an irq can be disabled and still wake the system if it has
been marked for wakeup.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/20200206191521.94559-1-swboyd@chromium.org
|
|
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.
Conversion rule is:
llseek => proc_lseek
unlocked_ioctl => proc_ioctl
xxx => proc_xxx
delete ".owner = THIS_MODULE" line
[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Conversion of the SiFive PLIC to hierarchical domains
- New SiFive GPIO irqchip driver
- New Aspeed SCI irqchip driver
- New NXP INTMUX irqchip driver
- Additional support for the Meson A1 GPIO irqchip
- First part of the GICv4.1 support
- Assorted fixes
|
|
The affinity of managed interrupts is completely handled in the kernel and
cannot be changed via the /proc/irq/* interfaces from user space. As the
kernel tries to spread out interrupts evenly accross CPUs on x86 to prevent
vector exhaustion, it can happen that a managed interrupt whose affinity
mask contains both isolated and housekeeping CPUs is routed to an isolated
CPU. As a consequence IO submitted on a housekeeping CPU causes interrupts
on the isolated CPU.
Add a new sub-parameter 'managed_irq' for 'isolcpus' and the corresponding
logic in the interrupt affinity selection code.
The subparameter indicates to the interrupt affinity selection logic that
it should try to avoid the above scenario.
This isolation is best effort and only effective if the automatically
assigned interrupt mask of a device queue contains isolated and
housekeeping CPUs. If housekeeping CPUs are online then such interrupts are
directed to the housekeeping CPU so that IO submitted on the housekeeping
CPU cannot disturb the isolated CPU.
If a queue's affinity mask contains only isolated CPUs then this parameter
has no effect on the interrupt routing decision, though interrupts are only
happening when tasks running on those isolated CPUs submit IO. IO submitted
on housekeeping CPUs has no influence on those queues.
If the affinity mask contains both housekeeping and isolated CPUs, but none
of the contained housekeeping CPUs is online, then the interrupt is also
routed to an isolated CPU. Interrupts are only delivered when one of the
isolated CPUs in the affinity mask submits IO. If one of the contained
housekeeping CPUs comes online, the CPU hotplug logic migrates the
interrupt automatically back to the upcoming housekeeping CPU. Depending on
the type of interrupt controller, this can require that at least one
interrupt is delivered to the isolated CPU in order to complete the
migration.
[ tglx: Removed unused parameter, added and edited comments/documentation
and rephrased the changelog so it contains more details. ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200120091625.17912-1-ming.lei@redhat.com
|
|
Fix a memory leak reported by kmemleak:
unreferenced object 0xffff000bc6f50e80 (size 128):
comm "kworker/23:2", pid 201, jiffies 4294894947 (age 942.132s)
hex dump (first 32 bytes):
00 00 00 00 41 00 00 00 86 c0 03 00 00 00 00 00 ....A...........
00 a0 b2 c6 0b 00 ff ff 40 51 fd 10 00 80 ff ff ........@Q......
backtrace:
[<00000000e62d2240>] kmem_cache_alloc_trace+0x1a4/0x320
[<00000000279143c9>] irq_domain_push_irq+0x7c/0x188
[<00000000d9f4c154>] thunderx_gpio_probe+0x3ac/0x438
[<00000000fd09ec22>] pci_device_probe+0xe4/0x198
[<00000000d43eca75>] really_probe+0xdc/0x320
[<00000000d3ebab09>] driver_probe_device+0x5c/0xf0
[<000000005b3ecaa0>] __device_attach_driver+0x88/0xc0
[<000000004e5915f5>] bus_for_each_drv+0x7c/0xc8
[<0000000079d4db41>] __device_attach+0xe4/0x140
[<00000000883bbda9>] device_initial_probe+0x18/0x20
[<000000003be59ef6>] bus_probe_device+0x98/0xa0
[<0000000039b03d3f>] deferred_probe_work_func+0x74/0xa8
[<00000000870934ce>] process_one_work+0x1c8/0x470
[<00000000e3cce570>] worker_thread+0x1f8/0x428
[<000000005d64975e>] kthread+0xfc/0x128
[<00000000f0eaa764>] ret_from_fork+0x10/0x18
Fixes: 495c38d3001f ("irqdomain: Add irq_domain_{push,pop}_irq() functions")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200120043547.22271-1-haokexin@gmail.com
|
|
Add a new function irq_domain_translate_onecell() that is to be used as
the translate function in struct irq_domain_ops.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1575976274-13487-2-git-send-email-yash.shah@sifive.com
|
|
Add __must_hold() annotation to address the following sparse warning:
warning: context imbalance in irq_wait_for_poll - unexpected unlock
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191216144208.29852-2-jbi.octave@gmail.com
|
|
Add __releases() annotation to address the following sparse warning:
warning: context imbalance in __irq_put_desc_unlock() - unexpected unlock
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191216144208.29852-1-jbi.octave@gmail.com
|
|
Requesting a threaded IRQ with handler=NULL and !ONESHOT fails, but the
error message does not include the IRQ line name, which makes it harder to
find the offending driver.
Print the IRQ line name to clarify where the error comes from. Use the same
format as the other pr_err() above in the same function.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191105140854.27893-1-luca@lucaceresoli.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
- Various cleanups
|
|
On certain QTI chipsets some GPIOs are direct-connect interrupts to the
GIC to be used as regular interrupt lines. When the GPIOs are not used
for interrupt generation the interrupt line is disabled. But disabling
the interrupt at GIC does not prevent the interrupt to be reported as
pending at GIC_ISPEND. Later, when drivers call enable_irq() on the
interrupt, an unwanted interrupt occurs.
Introduce get and set methods for irqchip's parent to clear it's pending
irq state. This then can be invoked by the GPIO interrupt controller on
the parents in it hierarchy to clear the interrupt before enabling the
interrupt.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-7-git-send-email-ilina@codeaurora.org
[updated commit text and minor code fixes]
|
|
The function got renamed at some point, but the kernel-doc was not updated.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1573656093-8643-1-git-send-email-zhangliguang@linux.alibaba.com
|
|
A recent commit changed a parameter of __irq_domain_alloc_fwnode(), but
did not update the documentation comment. Fix it up.
Fixes: b977fcf477c1 ("irqdomain/debugfs: Use PAs to generate fwnode names")
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1571476047-29463-1-git-send-email-wang.yi59@zte.com.cn
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core irq updates from Thomas Gleixner:
"Updates from the irq departement:
- Update the interrupt spreading code so it handles numa node with
different CPU counts properly.
- A large overhaul of the ARM GiCv3 driver to support new PPI and SPI
ranges.
- Conversion of all alloc_fwnode() users to use physical addresses
instead of virtual addresses so the virtual addresses are not
leaked. The physical address is sufficient to identify the
associated interrupt chip.
- Add support for Marvel MMP3, Amlogic Meson SM1 interrupt chips.
- Enforce interrupt threading at compile time if RT is enabled.
- Small updates and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices
irqchip/uniphier-aidet: Use devm_platform_ioremap_resource()
irqdomain: Add the missing assignment of domain->fwnode for named fwnode
irqchip/mmp: Coexist with GIC root IRQ controller
irqchip/mmp: Mask off interrupts from other cores
irqchip/mmp: Add missing chained_irq_{enter,exit}()
irqchip/mmp: Do not use of_address_to_resource() to get mux regs
irqchip/meson-gpio: Add support for meson sm1 SoCs
dt-bindings: interrupt-controller: New binding for the meson sm1 SoCs
genirq/affinity: Remove const qualifier from node_to_cpumask argument
genirq/affinity: Spread vectors on node according to nr_cpu ratio
genirq/affinity: Improve __irq_build_affinity_masks()
irqchip: Remove dev_err() usage after platform_get_irq()
irqchip: Add include guard to irq-partition-percpu.h
irqchip/mmp: Do not call irq_set_default_host() on DT platforms
irqchip/gic-v3-its: Remove the redundant set_bit for lpi_map
irqchip/gic-v3: Add quirks for HIP06/07 invalid GICD_TYPER erratum 161010803
irqchip/gic: Skip DT quirks when evaluating IIDR-based quirks
irqchip/gic-v3: Warn about inconsistent implementations of extended ranges
irqchip/gic-v3: Add EPPI range support
...
|
|
* pm-sleep: (29 commits)
ACPI: PM: s2idle: Always set up EC GPE for system wakeup
ACPI: PM: s2idle: Avoid rearming SCI for wakeup unnecessarily
PM / wakeup: Unexport wakeup_source_sysfs_{add,remove}()
PM / wakeup: Register wakeup class kobj after device is added
PM / wakeup: Fix sysfs registration error path
PM / wakeup: Show wakeup sources stats in sysfs
PM / wakeup: Use wakeup_source_register() in wakelock.c
PM / wakeup: Drop wakeup_source_init(), wakeup_source_prepare()
PM: sleep: Replace strncmp() with str_has_prefix()
PM: suspend: Fix platform_suspend_prepare_noirq()
intel-hid: Disable button array during suspend-to-idle
intel-hid: intel-vbtn: Avoid leaking wakeup_mode set
ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices
ACPI: EC: PM: Make acpi_ec_dispatch_gpe() print debug message
ACPI: EC: PM: Consolidate some code depending on PM_SLEEP
ACPI: PM: s2idle: Eliminate acpi_sleep_no_ec_events()
ACPI: PM: s2idle: Switch EC over to polling during "noirq" suspend
ACPI: PM: s2idle: Add acpi.sleep_no_lps0 module parameter
ACPI: PM: s2idle: Rearrange lps0_device_attach()
PM/sleep: Expose suspend stats in sysfs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- MAINTAINERS: Add Mark Rutland as perf submaintainer, Juri Lelli and
Vincent Guittot as scheduler submaintainers. Add Dietmar Eggemann,
Steven Rostedt, Ben Segall and Mel Gorman as scheduler reviewers.
As perf and the scheduler is getting bigger and more complex,
document the status quo of current responsibilities and interests,
and spread the review pain^H^H^H^H fun via an increase in the Cc:
linecount generated by scripts/get_maintainer.pl. :-)
- Add another series of patches that brings the -rt (PREEMPT_RT) tree
closer to mainline: split the monolithic CONFIG_PREEMPT dependencies
into a new CONFIG_PREEMPTION category that will allow the eventual
introduction of CONFIG_PREEMPT_RT. Still a few more hundred patches
to go though.
- Extend the CPU cgroup controller with uclamp.min and uclamp.max to
allow the finer shaping of CPU bandwidth usage.
- Micro-optimize energy-aware wake-ups from O(CPUS^2) to O(CPUS).
- Improve the behavior of high CPU count, high thread count
applications running under cpu.cfs_quota_us constraints.
- Improve balancing with SCHED_IDLE (SCHED_BATCH) tasks present.
- Improve CPU isolation housekeeping CPU allocation NUMA locality.
- Fix deadline scheduler bandwidth calculations and logic when cpusets
rebuilds the topology, or when it gets deadline-throttled while it's
being offlined.
- Convert the cpuset_mutex to percpu_rwsem, to allow it to be used from
setscheduler() system calls without creating global serialization.
Add new synchronization between cpuset topology-changing events and
the deadline acceptance tests in setscheduler(), which were broken
before.
- Rework the active_mm state machine to be less confusing and more
optimal.
- Rework (simplify) the pick_next_task() slowpath.
- Improve load-balancing on AMD EPYC systems.
- ... and misc cleanups, smaller fixes and improvements - please see
the Git log for more details.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
sched/psi: Correct overly pessimistic size calculation
sched/fair: Speed-up energy-aware wake-ups
sched/uclamp: Always use 'enum uclamp_id' for clamp_id values
sched/uclamp: Update CPU's refcount on TG's clamp changes
sched/uclamp: Use TG's clamps to restrict TASK's clamps
sched/uclamp: Propagate system defaults to the root group
sched/uclamp: Propagate parent clamps
sched/uclamp: Extend CPU's cgroup controller
sched/topology: Improve load balancing on AMD EPYC systems
arch, ia64: Make NUMA select SMP
sched, perf: MAINTAINERS update, add submaintainers and reviewers
sched/fair: Use rq_lock/unlock in online_fair_sched_group
cpufreq: schedutil: fix equation in comment
sched: Rework pick_next_task() slow-path
sched: Allow put_prev_task() to drop rq->lock
sched/fair: Expose newidle_balance()
sched: Add task_struct pointer to sched_class::set_curr_task
sched: Rework CPU hotplug task selection
sched/{rt,deadline}: Fix set_next_task vs pick_next_task
sched: Fix kerneldoc comment for ia64_set_curr_task
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for Linux 5.4 from Marc Zyngier:
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
|
|
The following crash was observed:
Unable to handle kernel NULL pointer dereference at 0000000000000158
Internal error: Oops: 96000004 [#1] SMP
pc : resend_irqs+0x68/0xb0
lr : resend_irqs+0x64/0xb0
...
Call trace:
resend_irqs+0x68/0xb0
tasklet_action_common.isra.6+0x84/0x138
tasklet_action+0x2c/0x38
__do_softirq+0x120/0x324
run_ksoftirqd+0x44/0x60
smpboot_thread_fn+0x1ac/0x1e8
kthread+0x134/0x138
ret_from_fork+0x10/0x18
The reason for this is that the interrupt resend mechanism happens in soft
interrupt context, which is a asynchronous mechanism versus other
operations on interrupts. free_irq() does not take resend handling into
account. Thus, the irq descriptor might be already freed before the resend
tasklet is executed. resend_irqs() does not check the return value of the
interrupt descriptor lookup and derefences the return value
unconditionally.
1):
__setup_irq
irq_startup
check_irq_resend // activate softirq to handle resend irq
2):
irq_domain_free_irqs
irq_free_descs
free_desc
call_rcu(&desc->rcu, delayed_free_desc)
3):
__do_softirq
tasklet_action
resend_irqs
desc = irq_to_desc(irq)
desc->handle_irq(desc) // desc is NULL --> Ooops
Fix this by adding a NULL pointer check in resend_irqs() before derefencing
the irq descriptor.
Fixes: a4633adcdbc1 ("[PATCH] genirq: add genirq sw IRQ-retrigger")
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1630ae13-5c8e-901e-de09-e740b6a426a7@huawei.com
|
|
Recently device pass-through stops working for Linux VM running on Hyper-V.
git-bisect shows the regression is caused by the recent commit
467a3bb97432 ("PCI: hv: Allocate a named fwnode ..."), but the root cause
is that the commit d59f6617eef0 forgets to set the domain->fwnode for
IRQCHIP_FWNODE_NAMED*, and as a result:
1. The domain->fwnode remains to be NULL.
2. irq_find_matching_fwspec() returns NULL since "h->fwnode == fwnode" is
false, and pci_set_bus_msi_domain() sets the Hyper-V PCI root bus's
msi_domain to NULL.
3. When the device is added onto the root bus, the device's dev->msi_domain
is set to NULL in pci_set_msi_domain().
4. When a device driver tries to enable MSI-X, pci_msi_setup_msi_irqs()
calls arch_setup_msi_irqs(), which uses the native MSI chip (i.e.
arch/x86/kernel/apic/msi.c: pci_msi_controller) to set up the irqs, but
actually pci_msi_setup_msi_irqs() is supposed to call
msi_domain_alloc_irqs() with the hbus->irq_domain, which is created in
hv_pcie_init_irq_domain() and is associated with the Hyper-V chip
hv_msi_irq_chip. Consequently, the irq line is not properly set up, and
the device driver can not receive any interrupt.
Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only")
Fixes: 467a3bb97432 ("PCI: hv: Allocate a named fwnode instead of an address-based one")
Reported-by: Lili Deng <v-lide@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/PU1P153MB01694D9AF625AC335C600C5FBFBE0@PU1P153MB0169.APCP153.PROD.OUTLOOK.COM
|
|
When CONFIG_CPUMASK_OFFSTACK isn't enabled, 'cpumask_var_t' is as
'typedef struct cpumask cpumask_var_t[1]',
so the argument 'node_to_cpumask' alloc_nodes_vectors() can't be declared
as 'const cpumask_var_t *'
Fixes the following warning:
kernel/irq/affinity.c: In function '__irq_build_affinity_masks':
alloc_nodes_vectors(numvecs, node_to_cpumask, cpu_mask,
^
kernel/irq/affinity.c:128:13: note: expected 'const struct cpumask (*)[1]' but argument is of type 'struct cpumask (*)[1]'
static void alloc_nodes_vectors(unsigned int numvecs,
^
Fixes: b1a5a73e64e9 ("genirq/affinity: Spread vectors on node according to nr_cpu ratio")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190828085815.19931-1-ming.lei@redhat.com
|
|
Now __irq_build_affinity_masks() spreads vectors evenly per node, but there
is a case that not all vectors have been spread when each numa node has a
different number of CPUs which triggers the warning in the spreading code.
Improve the spreading algorithm by
- assigning vectors according to the ratio of the number of CPUs on a node
to the number of remaining CPUs.
- running the assignment from smaller nodes to bigger nodes to guarantee
that every active node gets allocated at least one vector.
This ensures that all vectors are spread out. Asided of that the spread
becomes more fair if the nodes have different number of CPUs.
For example, on the following machine:
CPU(s): 16
On-line CPU(s) list: 0-15
Thread(s) per core: 1
Core(s) per socket: 8
Socket(s): 2
NUMA node(s): 2
...
NUMA node0 CPU(s): 0,1,3,5-9,11,13-15
NUMA node1 CPU(s): 2,4,10,12
When a driver requests to allocate 8 vectors, the following spread results:
irq 31, cpu list 2,4
irq 32, cpu list 10,12
irq 33, cpu list 0-1
irq 34, cpu list 3,5
irq 35, cpu list 6-7
irq 36, cpu list 8-9
irq 37, cpu list 11,13
irq 38, cpu list 14-15
So Node 0 has now 6 and Node 1 has 2 vectors assigned. The original
algorithm assigned 4 vectors on each node which was unfair versus Node 0.
[ tglx: Massaged changelog ]
Reported-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Link: https://lkml.kernel.org/r/20190816022849.14075-3-ming.lei@redhat.com
|
|
One invariant of __irq_build_affinity_masks() is that all CPUs in the
specified masks (cpu_mask AND node_to_cpumask for each node) should be
covered during the spread. Even though all requested vectors have been
reached, it's still required to spread vectors among remained CPUs. A
similar policy has been taken in case of 'numvecs <= nodes' already.
So remove the following check inside the loop:
if (done >= numvecs)
break;
Meantime assign at least 1 vector for remaining nodes if 'numvecs' vectors
have been handled already.
Also, if the specified cpumask for one numa node is empty, simply do not
spread vectors on this node.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190816022849.14075-2-ming.lei@redhat.com
|
|
If alloc_descs() fails before irq_sysfs_init() has run, free_desc() in the
cleanup path will call kobject_del() even though the kobject has not been
added with kobject_add().
Fix this by making the call to kobject_del() conditional on whether
irq_sysfs_init() has run.
This problem surfaced because commit aa30f47cf666 ("kobject: Add support
for default attribute groups to kobj_type") makes kobject_del() stricter
about pairing with kobject_add(). If the pairing is incorrrect, a WARNING
and backtrace occur in sysfs_remove_group() because there is no parent.
[ tglx: Add a comment to the code and make it work with CONFIG_SYSFS=n ]
Fixes: ecb3f394c5db ("genirq: Expose interrupt information through sysfs")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1564703564-4116-1-git-send-email-mikelley@microsoft.com
|
