| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement frequency/CPU invariance and OPP selection for
SCHED_DEADLINE (Juri Lelli)
- Tweak the task migration logic for better multi-tasking
workload scalability (Mel Gorman)
- Misc cleanups, fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Make bandwidth enforcement scale-invariant
sched/cpufreq: Move arch_scale_{freq,cpu}_capacity() outside of #ifdef CONFIG_SMP
sched/cpufreq: Remove arch_scale_freq_capacity()'s 'sd' parameter
sched/cpufreq: Always consider all CPUs when deciding next freq
sched/cpufreq: Split utilization signals
sched/cpufreq: Change the worker kthread to SCHED_DEADLINE
sched/deadline: Move CPU frequency selection triggering points
sched/cpufreq: Use the DEADLINE utilization signal
sched/deadline: Implement "runtime overrun signal" support
sched/fair: Only immediately migrate tasks due to interrupts if prev and target CPUs share cache
sched/fair: Correct obsolete comment about cpufreq_update_util()
sched/fair: Remove impossible condition from find_idlest_group_cpu()
sched/cpufreq: Don't pass flags to sugov_set_iowait_boost()
sched/cpufreq: Initialize sg_cpu->flags to 0
sched/fair: Consider RT/IRQ pressure in capacity_spare_wake()
sched/fair: Use 'unsigned long' for utilization, consistently
sched/core: Rework and clarify prepare_lock_switch()
sched/fair: Remove unused 'curr' parameter from wakeup_gran
sched/headers: Constify object_is_on_stack()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
|
|
Tejun reported the following cpu-hotplug lock (percpu-rwsem) read recursion:
tg_set_cfs_bandwidth()
get_online_cpus()
cpus_read_lock()
cfs_bandwidth_usage_inc()
static_key_slow_inc()
cpus_read_lock()
Reported-by: Tejun Heo <tj@kernel.org>
Tested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180122215328.GP3397@worktop
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Before commit:
e33a9bba85a8 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
delayacct_blkio_end() was called after context-switching into the task which
completed I/O.
This resulted in double counting: the task would account a delay both waiting
for I/O and for time spent in the runqueue.
With e33a9bba85a8, delayacct_blkio_end() is called by try_to_wake_up().
In ttwu, we have not yet context-switched. This is more correct, in that
the delay accounting ends when the I/O is complete.
But delayacct_blkio_end() relies on 'get_current()', and we have not yet
context-switched into the task whose I/O completed. This results in the
wrong task having its delay accounting statistics updated.
Instead of doing that, pass the task_struct being woken to delayacct_blkio_end(),
so that it can update the statistics of the correct task.
Signed-off-by: Josh Snyder <joshs@netflix.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Brendan Gregg <bgregg@netflix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-block@vger.kernel.org
Fixes: e33a9bba85a8 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
Link: http://lkml.kernel.org/r/1513613712-571-1-git-send-email-joshs@netflix.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A Kconfig fix, a build fix and a membarrier bug fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
membarrier: Disable preemption when calling smp_call_function_many()
sched/isolation: Make CONFIG_CPU_ISOLATION=y depend on SMP or COMPILE_TEST
ia64, sched/cputime: Fix build error if CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y
|
|
Apply frequency and CPU scale-invariance correction factor to bandwidth
enforcement (similar to what we already do to fair utilization tracking).
Each delta_exec gets scaled considering current frequency and maximum
CPU capacity; which means that the reservation runtime parameter (that
need to be specified profiling the task execution at max frequency on
biggest capacity core) gets thus scaled accordingly.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-9-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
CONFIG_SMP
Currently, frequency and cpu capacity scaling is only performed on
CONFIG_SMP systems (as CFS PELT signals are only present for such
systems). However, other scheduling classes want to do freq/cpu scaling,
and for !CONFIG_SMP configurations as well.
arch_scale_freq_capacity() is useful to implement frequency scaling even
on !CONFIG_SMP platforms, so we simply move it outside CONFIG_SMP
ifdeffery.
Even if arch_scale_cpu_capacity() is not useful on !CONFIG_SMP platforms,
we make a default implementation available for such configurations anyway
to simplify scheduler code doing CPU scale invariance.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: claudio@evidence.eu.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: luca.abeni@santannapisa.it
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Cc: viresh.kumar@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-8-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The 'sd' parameter is never used in arch_scale_freq_capacity() (and it's hard to
see where information coming from scheduling domains might help doing
frequency invariance scaling).
Remove it; also in anticipation of moving arch_scale_freq_capacity()
outside CONFIG_SMP.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: claudio@evidence.eu.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: luca.abeni@santannapisa.it
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Cc: viresh.kumar@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-7-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
No assumption can be made upon the rate at which frequency updates get
triggered, as there are scheduling policies (like SCHED_DEADLINE) which
don't trigger them so frequently.
Remove such assumption from the code, by always considering
SCHED_DEADLINE utilization signal as not stale.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-6-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
To be able to treat utilization signals of different scheduling classes
in different ways (e.g., CFS signal might be stale while DEADLINE signal
is never stale by design) we need to split sugov_cpu::util signal in two:
util_cfs and util_dl.
This patch does that by also changing sugov_get_util() parameter list.
After this change, aggregation of the different signals has to be performed
by sugov_get_util() users (so that they can decide what to do with the
different signals).
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-5-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Worker kthread needs to be able to change frequency for all other
threads.
Make it special, just under STOP class.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-4-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since SCHED_DEADLINE doesn't track utilization signal (but reserves a
fraction of CPU bandwidth to tasks admitted to the system), there is no
point in evaluating frequency changes during each tick event.
Move frequency selection triggering points to where running_bw changes.
Co-authored-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-3-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
SCHED_DEADLINE tracks active utilization signal with a per dl_rq
variable named running_bw.
Make use of that to drive CPU frequency selection: add up FAIR and
DEADLINE contribution to get the required CPU capacity to handle both
requirements (while RT still selects max frequency).
Co-authored-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: alessio.balsini@arm.com
Cc: bristot@redhat.com
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: mathieu.poirier@linaro.org
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: rjw@rjwysocki.net
Cc: rostedt@goodmis.org
Cc: tkjos@android.com
Cc: tommaso.cucinotta@santannapisa.it
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/20171204102325.5110-2-juri.lelli@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch adds the possibility of getting the delivery of a SIGXCPU
signal whenever there is a runtime overrun. The request is done through
the sched_flags field within the sched_attr structure.
Forward port of https://lkml.org/lkml/2009/10/16/170
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Luca Abeni <luca.abeni@santannapisa.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Link: http://lkml.kernel.org/r/1513077024-25461-1-git-send-email-claudio@evidence.eu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
target CPUs share cache
If waking from an idle CPU due to an interrupt then it's possible that
the waker task will be pulled to wake on the current CPU. Unfortunately,
depending on the type of interrupt and IRQ configuration, there may not
be a strong relationship between the CPU an interrupt was delivered on
and the CPU a task was running on. For example, the interrupts could all
be delivered to CPUs on one particular node due to the machine topology
or IRQ affinity configuration. Another example is an interrupt for an IO
completion which can be delivered to any CPU where there is no guarantee
the data is either cache hot or even local.
This patch was motivated by the observation that an IO workload was
being pulled cross-node on a frequent basis when IO completed. From a
wakeup latency perspective, it's still useful to know that an idle CPU is
immediately available for use but lets only consider an automatic migration
if the CPUs share cache to limit damage due to NUMA migrations. Migrations
may still occur if wake_affine_weight determines it's appropriate.
These are the throughput results for dbench running on ext4 comparing
4.15-rc3 and this patch on a 2-socket machine where interrupts due to IO
completions can happen on any CPU.
4.15.0-rc3 4.15.0-rc3
vanilla lessmigrate
Hmean 1 854.64 ( 0.00%) 865.01 ( 1.21%)
Hmean 2 1229.60 ( 0.00%) 1274.44 ( 3.65%)
Hmean 4 1591.81 ( 0.00%) 1628.08 ( 2.28%)
Hmean 8 1845.04 ( 0.00%) 1831.80 ( -0.72%)
Hmean 16 2038.61 ( 0.00%) 2091.44 ( 2.59%)
Hmean 32 2327.19 ( 0.00%) 2430.29 ( 4.43%)
Hmean 64 2570.61 ( 0.00%) 2568.54 ( -0.08%)
Hmean 128 2481.89 ( 0.00%) 2499.28 ( 0.70%)
Stddev 1 14.31 ( 0.00%) 5.35 ( 62.65%)
Stddev 2 21.29 ( 0.00%) 11.09 ( 47.92%)
Stddev 4 7.22 ( 0.00%) 6.80 ( 5.92%)
Stddev 8 26.70 ( 0.00%) 9.41 ( 64.76%)
Stddev 16 22.40 ( 0.00%) 20.01 ( 10.70%)
Stddev 32 45.13 ( 0.00%) 44.74 ( 0.85%)
Stddev 64 93.10 ( 0.00%) 93.18 ( -0.09%)
Stddev 128 184.28 ( 0.00%) 177.85 ( 3.49%)
Note the small increase in throughput for low thread counts but also
note that the standard deviation for each sample during the test run is
lower. The throughput figures for dbench can be misleading so the benchmark
is actually modified to time the latency of the processing of one load
file with many samples taken. The difference in latency is
4.15.0-rc3 4.15.0-rc3
vanilla lessmigrate
Amean 1 21.71 ( 0.00%) 21.47 ( 1.08%)
Amean 2 30.89 ( 0.00%) 29.58 ( 4.26%)
Amean 4 47.54 ( 0.00%) 46.61 ( 1.97%)
Amean 8 82.71 ( 0.00%) 82.81 ( -0.12%)
Amean 16 149.45 ( 0.00%) 145.01 ( 2.97%)
Amean 32 265.49 ( 0.00%) 248.43 ( 6.42%)
Amean 64 463.23 ( 0.00%) 463.55 ( -0.07%)
Amean 128 933.97 ( 0.00%) 935.50 ( -0.16%)
Stddev 1 1.58 ( 0.00%) 1.54 ( 2.26%)
Stddev 2 2.84 ( 0.00%) 2.95 ( -4.15%)
Stddev 4 6.78 ( 0.00%) 6.85 ( -0.99%)
Stddev 8 16.85 ( 0.00%) 16.37 ( 2.85%)
Stddev 16 41.59 ( 0.00%) 41.04 ( 1.32%)
Stddev 32 111.05 ( 0.00%) 105.11 ( 5.35%)
Stddev 64 285.94 ( 0.00%) 288.01 ( -0.72%)
Stddev 128 803.39 ( 0.00%) 809.73 ( -0.79%)
It's a small improvement which is not surprising given that migrations that
migrate to a different node as not that common. However, it is noticeable
in the CPU migration statistics which are reduced by 24%.
There was a query for v1 of this patch about NAS so here are the results
for C-class using MPI for parallelisation on the same machine
nas-mpi
4.15.0-rc3 4.15.0-rc3
vanilla noirq
Time cg.C 24.25 ( 0.00%) 23.17 ( 4.45%)
Time ep.C 8.22 ( 0.00%) 8.29 ( -0.85%)
Time ft.C 22.67 ( 0.00%) 20.34 ( 10.28%)
Time is.C 1.42 ( 0.00%) 1.47 ( -3.52%)
Time lu.C 55.62 ( 0.00%) 54.81 ( 1.46%)
Time mg.C 7.93 ( 0.00%) 7.91 ( 0.25%)
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
User 3799.96 3748.34
System 672.10 626.15
Elapsed 91.91 79.49
lu.C sees a small gain, ft.C a large gain and ep.C and is.C see small
regressions but in terms of absolute time, the difference is small and
likely within run-to-run variance. System CPU usage is slightly reduced.
schbench from Facebook was also requested. This is a bit of a mixed bag but
it's important to note that this workload should not be heavily impacted
by wakeups from interrupt context.
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
Lat 50.00th-qrtle-1 41.00 ( 0.00%) 41.00 ( 0.00%)
Lat 75.00th-qrtle-1 42.00 ( 0.00%) 42.00 ( 0.00%)
Lat 90.00th-qrtle-1 43.00 ( 0.00%) 44.00 ( -2.33%)
Lat 95.00th-qrtle-1 44.00 ( 0.00%) 46.00 ( -4.55%)
Lat 99.00th-qrtle-1 57.00 ( 0.00%) 58.00 ( -1.75%)
Lat 99.50th-qrtle-1 59.00 ( 0.00%) 59.00 ( 0.00%)
Lat 99.90th-qrtle-1 67.00 ( 0.00%) 78.00 ( -16.42%)
Lat 50.00th-qrtle-2 40.00 ( 0.00%) 51.00 ( -27.50%)
Lat 75.00th-qrtle-2 45.00 ( 0.00%) 56.00 ( -24.44%)
Lat 90.00th-qrtle-2 53.00 ( 0.00%) 59.00 ( -11.32%)
Lat 95.00th-qrtle-2 57.00 ( 0.00%) 61.00 ( -7.02%)
Lat 99.00th-qrtle-2 67.00 ( 0.00%) 71.00 ( -5.97%)
Lat 99.50th-qrtle-2 69.00 ( 0.00%) 74.00 ( -7.25%)
Lat 99.90th-qrtle-2 83.00 ( 0.00%) 77.00 ( 7.23%)
Lat 50.00th-qrtle-4 51.00 ( 0.00%) 51.00 ( 0.00%)
Lat 75.00th-qrtle-4 57.00 ( 0.00%) 56.00 ( 1.75%)
Lat 90.00th-qrtle-4 60.00 ( 0.00%) 59.00 ( 1.67%)
Lat 95.00th-qrtle-4 62.00 ( 0.00%) 62.00 ( 0.00%)
Lat 99.00th-qrtle-4 73.00 ( 0.00%) 72.00 ( 1.37%)
Lat 99.50th-qrtle-4 76.00 ( 0.00%) 74.00 ( 2.63%)
Lat 99.90th-qrtle-4 85.00 ( 0.00%) 78.00 ( 8.24%)
Lat 50.00th-qrtle-8 54.00 ( 0.00%) 58.00 ( -7.41%)
Lat 75.00th-qrtle-8 59.00 ( 0.00%) 62.00 ( -5.08%)
Lat 90.00th-qrtle-8 65.00 ( 0.00%) 66.00 ( -1.54%)
Lat 95.00th-qrtle-8 67.00 ( 0.00%) 70.00 ( -4.48%)
Lat 99.00th-qrtle-8 78.00 ( 0.00%) 79.00 ( -1.28%)
Lat 99.50th-qrtle-8 81.00 ( 0.00%) 80.00 ( 1.23%)
Lat 99.90th-qrtle-8 116.00 ( 0.00%) 83.00 ( 28.45%)
Lat 50.00th-qrtle-16 65.00 ( 0.00%) 64.00 ( 1.54%)
Lat 75.00th-qrtle-16 77.00 ( 0.00%) 71.00 ( 7.79%)
Lat 90.00th-qrtle-16 83.00 ( 0.00%) 82.00 ( 1.20%)
Lat 95.00th-qrtle-16 87.00 ( 0.00%) 87.00 ( 0.00%)
Lat 99.00th-qrtle-16 95.00 ( 0.00%) 96.00 ( -1.05%)
Lat 99.50th-qrtle-16 99.00 ( 0.00%) 103.00 ( -4.04%)
Lat 99.90th-qrtle-16 104.00 ( 0.00%) 122.00 ( -17.31%)
Lat 50.00th-qrtle-32 71.00 ( 0.00%) 73.00 ( -2.82%)
Lat 75.00th-qrtle-32 91.00 ( 0.00%) 92.00 ( -1.10%)
Lat 90.00th-qrtle-32 108.00 ( 0.00%) 107.00 ( 0.93%)
Lat 95.00th-qrtle-32 118.00 ( 0.00%) 115.00 ( 2.54%)
Lat 99.00th-qrtle-32 134.00 ( 0.00%) 129.00 ( 3.73%)
Lat 99.50th-qrtle-32 138.00 ( 0.00%) 133.00 ( 3.62%)
Lat 99.90th-qrtle-32 149.00 ( 0.00%) 146.00 ( 2.01%)
Lat 50.00th-qrtle-39 83.00 ( 0.00%) 81.00 ( 2.41%)
Lat 75.00th-qrtle-39 105.00 ( 0.00%) 102.00 ( 2.86%)
Lat 90.00th-qrtle-39 120.00 ( 0.00%) 119.00 ( 0.83%)
Lat 95.00th-qrtle-39 129.00 ( 0.00%) 128.00 ( 0.78%)
Lat 99.00th-qrtle-39 153.00 ( 0.00%) 149.00 ( 2.61%)
Lat 99.50th-qrtle-39 166.00 ( 0.00%) 156.00 ( 6.02%)
Lat 99.90th-qrtle-39 12304.00 ( 0.00%) 12848.00 ( -4.42%)
When heavily loaded (e.g. 99.50th-qrtle-39 indicates 39 threads), there
are small gains in many cases. Otherwise it depends on the quartile used
where it can be bad -- e.g. 75.00th-qrtle-2. However, even these results
are probably a co-incidence. For this workload, much depends on what node
the threads get placed on and their relative locality and not wakeups from
interrupt context. A larger component on how it behaves would be automatic
NUMA balancing where a fault incurred to measure locality would be a much
larger contributer to latency than the wakeup path.
This is the results from an almost identical machine that happened to run
the same test. They only differ in terms of storage which is irrelevant
for this test.
4.15.0-rc3 4.15.0-rc3
vanilla noirq-v1r1
Lat 50.00th-qrtle-1 41.00 ( 0.00%) 41.00 ( 0.00%)
Lat 75.00th-qrtle-1 42.00 ( 0.00%) 42.00 ( 0.00%)
Lat 90.00th-qrtle-1 44.00 ( 0.00%) 43.00 ( 2.27%)
Lat 95.00th-qrtle-1 53.00 ( 0.00%) 45.00 ( 15.09%)
Lat 99.00th-qrtle-1 59.00 ( 0.00%) 58.00 ( 1.69%)
Lat 99.50th-qrtle-1 60.00 ( 0.00%) 59.00 ( 1.67%)
Lat 99.90th-qrtle-1 86.00 ( 0.00%) 61.00 ( 29.07%)
Lat 50.00th-qrtle-2 52.00 ( 0.00%) 41.00 ( 21.15%)
Lat 75.00th-qrtle-2 57.00 ( 0.00%) 46.00 ( 19.30%)
Lat 90.00th-qrtle-2 60.00 ( 0.00%) 53.00 ( 11.67%)
Lat 95.00th-qrtle-2 62.00 ( 0.00%) 57.00 ( 8.06%)
Lat 99.00th-qrtle-2 73.00 ( 0.00%) 68.00 ( 6.85%)
Lat 99.50th-qrtle-2 74.00 ( 0.00%) 71.00 ( 4.05%)
Lat 99.90th-qrtle-2 90.00 ( 0.00%) 75.00 ( 16.67%)
Lat 50.00th-qrtle-4 57.00 ( 0.00%) 52.00 ( 8.77%)
Lat 75.00th-qrtle-4 60.00 ( 0.00%) 58.00 ( 3.33%)
Lat 90.00th-qrtle-4 62.00 ( 0.00%) 62.00 ( 0.00%)
Lat 95.00th-qrtle-4 65.00 ( 0.00%) 65.00 ( 0.00%)
Lat 99.00th-qrtle-4 76.00 ( 0.00%) 75.00 ( 1.32%)
Lat 99.50th-qrtle-4 77.00 ( 0.00%) 77.00 ( 0.00%)
Lat 99.90th-qrtle-4 87.00 ( 0.00%) 81.00 ( 6.90%)
Lat 50.00th-qrtle-8 59.00 ( 0.00%) 57.00 ( 3.39%)
Lat 75.00th-qrtle-8 63.00 ( 0.00%) 62.00 ( 1.59%)
Lat 90.00th-qrtle-8 66.00 ( 0.00%) 67.00 ( -1.52%)
Lat 95.00th-qrtle-8 68.00 ( 0.00%) 70.00 ( -2.94%)
Lat 99.00th-qrtle-8 79.00 ( 0.00%) 80.00 ( -1.27%)
Lat 99.50th-qrtle-8 80.00 ( 0.00%) 84.00 ( -5.00%)
Lat 99.90th-qrtle-8 84.00 ( 0.00%) 90.00 ( -7.14%)
Lat 50.00th-qrtle-16 65.00 ( 0.00%) 65.00 ( 0.00%)
Lat 75.00th-qrtle-16 77.00 ( 0.00%) 75.00 ( 2.60%)
Lat 90.00th-qrtle-16 84.00 ( 0.00%) 83.00 ( 1.19%)
Lat 95.00th-qrtle-16 88.00 ( 0.00%) 87.00 ( 1.14%)
Lat 99.00th-qrtle-16 97.00 ( 0.00%) 96.00 ( 1.03%)
Lat 99.50th-qrtle-16 100.00 ( 0.00%) 104.00 ( -4.00%)
Lat 99.90th-qrtle-16 110.00 ( 0.00%) 126.00 ( -14.55%)
Lat 50.00th-qrtle-32 70.00 ( 0.00%) 71.00 ( -1.43%)
Lat 75.00th-qrtle-32 92.00 ( 0.00%) 94.00 ( -2.17%)
Lat 90.00th-qrtle-32 110.00 ( 0.00%) 110.00 ( 0.00%)
Lat 95.00th-qrtle-32 121.00 ( 0.00%) 118.00 ( 2.48%)
Lat 99.00th-qrtle-32 135.00 ( 0.00%) 137.00 ( -1.48%)
Lat 99.50th-qrtle-32 140.00 ( 0.00%) 146.00 ( -4.29%)
Lat 99.90th-qrtle-32 150.00 ( 0.00%) 160.00 ( -6.67%)
Lat 50.00th-qrtle-39 80.00 ( 0.00%) 71.00 ( 11.25%)
Lat 75.00th-qrtle-39 102.00 ( 0.00%) 91.00 ( 10.78%)
Lat 90.00th-qrtle-39 118.00 ( 0.00%) 108.00 ( 8.47%)
Lat 95.00th-qrtle-39 128.00 ( 0.00%) 117.00 ( 8.59%)
Lat 99.00th-qrtle-39 149.00 ( 0.00%) 133.00 ( 10.74%)
Lat 99.50th-qrtle-39 160.00 ( 0.00%) 139.00 ( 13.12%)
Lat 99.90th-qrtle-39 13808.00 ( 0.00%) 4920.00 ( 64.37%)
Despite being nearly identical, it showed a variety of major gains so
I'm not convinced that heavy emphasis should be placed on this particular
workload in terms of evaluating this particular patch. Further evidence of
this is the fact that testing on a UMA machine showed small gains/losses
even though the patch should be a no-op on UMA.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171219085947.13136-2-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the remote cpufreq callback work, the cpufreq_update_util() call can happen
from remote CPUs. The comment about local CPUs is thus obsolete. Update it
accordingly.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Android Kernel <kernel-team@android.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: EAS Dev <eas-dev@lists.linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rohit Jain <rohit.k.jain@oracle.com>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/20171215153944.220146-2-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
find_idlest_group_cpu() goes through CPUs of a group previous selected by
find_idlest_group(). find_idlest_group() returns NULL if the local group is the
selected one and doesn't execute find_idlest_group_cpu if the group to which
'cpu' belongs to is chosen. So we're always guaranteed to call
find_idlest_group_cpu() with a group to which 'cpu' is non-local.
This makes one of the conditions in find_idlest_group_cpu() an impossible one,
which we can get rid off.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Android Kernel <kernel-team@android.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: EAS Dev <eas-dev@lists.linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rohit Jain <rohit.k.jain@oracle.com>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171215153944.220146-3-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We are already passing sg_cpu as argument to sugov_set_iowait_boost()
helper and the same can be used to retrieve the flags value. Get rid of
the redundant argument.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: juri.lelli@redhat.com
Cc: morten.rasmussen@arm.com
Cc: tkjos@android.com
Link: http://lkml.kernel.org/r/4ec5562b1a87e146ebab11fb5dde1ca9c763a7fb.1513158452.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Initializing sg_cpu->flags to SCHED_CPUFREQ_RT has no obvious benefit.
The flags field wouldn't be used until the utilization update handler is
called for the first time, and once that is called we will overwrite
flags anyway.
Initialize it to 0.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: dietmar.eggemann@arm.com
Cc: joelaf@google.com
Cc: morten.rasmussen@arm.com
Cc: tkjos@android.com
Link: http://lkml.kernel.org/r/763feda6424ced8486b25a0c52979634e6104478.1513158452.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
capacity_spare_wake() in the slow path influences choice of idlest groups,
as we search for groups with maximum spare capacity. In scenarios where
RT pressure is high, a sub optimal group can be chosen and hurt
performance of the task being woken up.
Fix this by using capacity_of() instead of capacity_orig_of() in capacity_spare_wake().
Tests results from improvements with this change are below. More tests
were also done by myself and Matt Fleming to ensure no degradation in
different benchmarks.
1) Rohit ran barrier.c test (details below) with following improvements:
------------------------------------------------------------------------
This was Rohit's original use case for a patch he posted at [1] however
from his recent tests he showed my patch can replace his slow path
changes [1] and there's no need to selectively scan/skip CPUs in
find_idlest_group_cpu in the slow path to get the improvement he sees.
barrier.c (open_mp code) as a micro-benchmark. It does a number of
iterations and barrier sync at the end of each for loop.
Here barrier,c is running in along with ping on CPU 0 and 1 as:
'ping -l 10000 -q -s 10 -f hostX'
barrier.c can be found at:
http://www.spinics.net/lists/kernel/msg2506955.html
Following are the results for the iterations per second with this
micro-benchmark (higher is better), on a 44 core, 2 socket 88 Threads
Intel x86 machine:
+--------+------------------+---------------------------+
|Threads | Without patch | With patch |
| | | |
+--------+--------+---------+-----------------+---------+
| | Mean | Std Dev | Mean | Std Dev |
+--------+--------+---------+-----------------+---------+
|1 | 539.36 | 60.16 | 572.54 (+6.15%) | 40.95 |
|2 | 481.01 | 19.32 | 530.64 (+10.32%)| 56.16 |
|4 | 474.78 | 22.28 | 479.46 (+0.99%) | 18.89 |
|8 | 450.06 | 24.91 | 447.82 (-0.50%) | 12.36 |
|16 | 436.99 | 22.57 | 441.88 (+1.12%) | 7.39 |
|32 | 388.28 | 55.59 | 429.4 (+10.59%)| 31.14 |
|64 | 314.62 | 6.33 | 311.81 (-0.89%) | 11.99 |
+--------+--------+---------+-----------------+---------+
2) ping+hackbench test on bare-metal sever (by Rohit)
-----------------------------------------------------
Here hackbench is running in threaded mode along
with, running ping on CPU 0 and 1 as:
'ping -l 10000 -q -s 10 -f hostX'
This test is running on 2 socket, 20 core and 40 threads Intel x86
machine:
Number of loops is 10000 and runtime is in seconds (Lower is better).
+--------------+-----------------+--------------------------+
|Task Groups | Without patch | With patch |
| +-------+---------+----------------+---------+
|(Groups of 40)| Mean | Std Dev | Mean | Std Dev |
+--------------+-------+---------+----------------+---------+
|1 | 0.851 | 0.007 | 0.828 (+2.77%)| 0.032 |
|2 | 1.083 | 0.203 | 1.087 (-0.37%)| 0.246 |
|4 | 1.601 | 0.051 | 1.611 (-0.62%)| 0.055 |
|8 | 2.837 | 0.060 | 2.827 (+0.35%)| 0.031 |
|16 | 5.139 | 0.133 | 5.107 (+0.63%)| 0.085 |
|25 | 7.569 | 0.142 | 7.503 (+0.88%)| 0.143 |
+--------------+-------+---------+----------------+---------+
[1] https://patchwork.kernel.org/patch/9991635/
Matt Fleming also ran several different hackbench tests and cyclic test
to santiy-check that the patch doesn't harm other usecases.
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Tested-by: Rohit Jain <rohit.k.jain@oracle.com>
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Atish Patra <atish.patra@oracle.com>
Cc: Brendan Jackman <brendan.jackman@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Ramussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Saravana Kannan <skannan@quicinc.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171214212158.188190-1-joelaf@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Utilization and capacity are tracked as 'unsigned long', however some
functions using them return an 'int' which is ultimately assigned back to
'unsigned long' variables.
Since there is not scope on using a different and signed type,
consolidate the signature of functions returning utilization to always
use the native type.
This change improves code consistency, and it also benefits
code paths where utilizations should be clamped by avoiding
further type conversions or ugly type casts.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Redpath <chris.redpath@arm.com>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@android.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20171205171018.9203-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The prepare_lock_switch() function has an unused parameter, and also the
function name was not descriptive. To improve readability and remove
the extra parameter, do the following changes:
* Move prepare_lock_switch() from kernel/sched/sched.h to
kernel/sched/core.c, rename it to prepare_task(), and remove the
unused parameter.
* Split the smp_store_release() out from finish_lock_switch() to a
function named finish_task.
* Comments ajdustments.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171215140603.gxe5i2y6fg5ojfpp@smtp.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
smp_call_function_many() requires disabling preemption around the call.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: <stable@vger.kernel.org> # v4.14+
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171215192310.25293-1-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's two cross-release leftover facilities:
- the crossrelease_hist_*() irq-tracing callbacks (NOPs currently)
- the complete_release_commit() callback (NOP as well)
Remove them.
Cc: David Sterba <dsterba@suse.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull RCU updates from Paul E. McKenney:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and
in kernel/torture.c). Also a couple of fixes to avoid sending
IPIs to offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends()
and read_barrier_depends().
- Miscellaneous fixes.
- Torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since the recent remote cpufreq callback work, its possible that a cpufreq
update is triggered from a remote CPU. For single policies however, the current
code uses the local CPU when trying to determine if the remote sg_cpu entered
idle or is busy. This is incorrect. To remedy this, compare with the nohz tick
idle_calls counter of the remote CPU.
Fixes: 674e75411fc2 (sched: cpufreq: Allow remote cpufreq callbacks)
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Joel Fernandes <joelaf@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Daniel Wagner reported a crash on the BeagleBone Black SoC.
This is a single CPU architecture, and does not have a functional
arch_send_call_function_single_ipi() implementation which can crash
the kernel if that is called.
As it only has one CPU, it shouldn't be called, but if the kernel is
compiled for SMP, the push/pull RT scheduling logic now calls it for
irq_work if the one CPU is overloaded, it can use that function to call
itself and crash the kernel.
Ideally, we should disable the SCHED_FEAT(RT_PUSH_IPI) if the system
only has a single CPU. But SCHED_FEAT is a constant if sched debugging
is turned off. Another fix can also be used, and this should also help
with normal SMP machines. That is, do not initiate the pull code if
there's only one RT overloaded CPU, and that CPU happens to be the
current CPU that is scheduling in a lower priority task.
Even on a system with many CPUs, if there's many RT tasks waiting to
run on a single CPU, and that CPU schedules in another RT task of lower
priority, it will initiate the PULL logic in case there's a higher
priority RT task on another CPU that is waiting to run. But if there is
no other CPU with waiting RT tasks, it will initiate the RT pull logic
on itself (as it still has RT tasks waiting to run). This is a wasted
effort.
Not only does this help with SMP code where the current CPU is the only
one with RT overloaded tasks, it should also solve the issue that
Daniel encountered, because it will prevent the PULL logic from
executing, as there's only one CPU on the system, and the check added
here will cause it to exit the RT pull code.
Reported-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-rt-users <linux-rt-users@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 4bdced5c9 ("sched/rt: Simplify the IPI based RT balancing logic")
Link: http://lkml.kernel.org/r/20171202130454.4cbbfe8d@vmware.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix the following kernel-doc warnings after code restructuring:
../kernel/sched/core.c:5113: warning: No description found for parameter 't'
../kernel/sched/core.c:5113: warning: Excess function parameter 'interval' description in 'sched_rr_get_interval'
get rid of set_fs()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: abca5fc535a3e ("sched_rr_get_interval(): move compat to native,
Link: http://lkml.kernel.org/r/995c6ded-b32e-bbe4-d9f5-4d42d121aff1@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The first parameter of wakeup_gran(), 'curr', is unnecessary now.
Signed-off-by: Cheng Jian <cj.chengjian@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: huawei.libin@huawei.com
Cc: xiexiuqi@huawei.com
Link: http://lkml.kernel.org/r/1512653443-179848-1-git-send-email-cj.chengjian@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Unlike running, the runnable part can't be directly propagated through
the hierarchy when we migrate a task. The main reason is that runnable
time can be shared with other sched_entities that stay on the rq and
this runnable time will also remain on prev cfs_rq and must not be
removed.
Instead, we can estimate what should be the new runnable of the prev
cfs_rq and check that this estimation stay in a possible range. The
prop_runnable_sum is a good estimation when adding runnable_sum but
fails most often when we remove it. Instead, we could use the formula
below instead:
gcfs_rq's runnable_sum = gcfs_rq->avg.load_sum / gcfs_rq->load.weight
which assumes that tasks are equally runnable which is not true but
easy to compute.
Beside these estimates, we have several simple rules that help us to filter
out wrong ones:
- ge->avg.runnable_sum <= than LOAD_AVG_MAX
- ge->avg.runnable_sum >= ge->avg.running_sum (ge->avg.util_sum << LOAD_AVG_MAX)
- ge->avg.runnable_sum can't increase when we detach a task
The effect of these fixes is better cgroups balancing.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Link: http://lkml.kernel.org/r/1510842112-21028-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The following cleanup commit:
50816c48997a ("sched/wait: Standardize internal naming of wait-queue entries")
... unintentionally changed the behavior of add_wait_queue() from
inserting the wait entry at the head of the wait queue to the tail
of the wait queue.
Beyond a negative performance impact this change in behavior
theoretically also breaks wait queues which mix exclusive and
non-exclusive waiters, as non-exclusive waiters will not be
woken up if they are queued behind enough exclusive waiters.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-team@fb.com
Fixes: ("sched/wait: Standardize internal naming of wait-queue entries")
Link: http://lkml.kernel.org/r/a16c8ccffd39bd08fdaa45a5192294c784b803a7.1512544324.git.osandov@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The rcutorture test suite occasionally provokes a splat due to invoking
rt_mutex_lock() which needs to boost the priority of a task currently
sitting on a runqueue that belongs to an offline CPU:
WARNING: CPU: 0 PID: 12 at /home/paulmck/public_git/linux-rcu/arch/x86/kernel/smp.c:128 native_smp_send_reschedule+0x37/0x40
Modules linked in:
CPU: 0 PID: 12 Comm: rcub/7 Not tainted 4.14.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff9ed3de5f8cc0 task.stack: ffffbbf80012c000
RIP: 0010:native_smp_send_reschedule+0x37/0x40
RSP: 0018:ffffbbf80012fd10 EFLAGS: 00010082
RAX: 000000000000002f RBX: ffff9ed3dd9cb300 RCX: 0000000000000004
RDX: 0000000080000004 RSI: 0000000000000086 RDI: 00000000ffffffff
RBP: ffffbbf80012fd10 R08: 000000000009da7a R09: 0000000000007b9d
R10: 0000000000000001 R11: ffffffffbb57c2cd R12: 000000000000000d
R13: ffff9ed3de5f8cc0 R14: 0000000000000061 R15: ffff9ed3ded59200
FS: 0000000000000000(0000) GS:ffff9ed3dea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000080686f0 CR3: 000000001b9e0000 CR4: 00000000000006f0
Call Trace:
resched_curr+0x61/0xd0
switched_to_rt+0x8f/0xa0
rt_mutex_setprio+0x25c/0x410
task_blocks_on_rt_mutex+0x1b3/0x1f0
rt_mutex_slowlock+0xa9/0x1e0
rt_mutex_lock+0x29/0x30
rcu_boost_kthread+0x127/0x3c0
kthread+0x104/0x140
? rcu_report_unblock_qs_rnp+0x90/0x90
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x22/0x30
Code: f0 00 0f 92 c0 84 c0 74 14 48 8b 05 34 74 c5 00 be fd 00 00 00 ff 90 a0 00 00 00 5d c3 89 fe 48 c7 c7 a0 c6 fc b9 e8 d5 b5 06 00 <0f> ff 5d c3 0f 1f 44 00 00 8b 05 a2 d1 13 02 85 c0 75 38 55 48
But the target task's priority has already been adjusted, so the only
purpose of switched_to_rt() invoking resched_curr() is to wake up the
CPU running some task that needs to be preempted by the boosted task.
But the CPU is offline, which presumably means that the task must be
migrated to some other CPU, and that this other CPU will undertake any
needed preemption at the time of migration. Because the runqueue lock
is held when resched_curr() is invoked, we know that the boosted task
cannot go anywhere, so it is not necessary to invoke resched_curr()
in this particular case.
This commit therefore makes switched_to_rt() refrain from invoking
resched_curr() when the target CPU is offline.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
The rcutorture test suite occasionally provokes a splat due to invoking
resched_cpu() on an offline CPU:
WARNING: CPU: 2 PID: 8 at /home/paulmck/public_git/linux-rcu/arch/x86/kernel/smp.c:128 native_smp_send_reschedule+0x37/0x40
Modules linked in:
CPU: 2 PID: 8 Comm: rcu_preempt Not tainted 4.14.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff902ede9daf00 task.stack: ffff96c50010c000
RIP: 0010:native_smp_send_reschedule+0x37/0x40
RSP: 0018:ffff96c50010fdb8 EFLAGS: 00010096
RAX: 000000000000002e RBX: ffff902edaab4680 RCX: 0000000000000003
RDX: 0000000080000003 RSI: 0000000000000000 RDI: 00000000ffffffff
RBP: ffff96c50010fdb8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 00000000299f36ae R12: 0000000000000001
R13: ffffffff9de64240 R14: 0000000000000001 R15: ffffffff9de64240
FS: 0000000000000000(0000) GS:ffff902edfc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f7d4c642 CR3: 000000001e0e2000 CR4: 00000000000006e0
Call Trace:
resched_curr+0x8f/0x1c0
resched_cpu+0x2c/0x40
rcu_implicit_dynticks_qs+0x152/0x220
force_qs_rnp+0x147/0x1d0
? sync_rcu_exp_select_cpus+0x450/0x450
rcu_gp_kthread+0x5a9/0x950
kthread+0x142/0x180
? force_qs_rnp+0x1d0/0x1d0
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x27/0x40
Code: 14 01 0f 92 c0 84 c0 74 14 48 8b 05 14 4f f4 00 be fd 00 00 00 ff 90 a0 00 00 00 5d c3 89 fe 48 c7 c7 38 89 ca 9d e8 e5 56 08 00 <0f> ff 5d c3 0f 1f 44 00 00 8b 05 52 9e 37 02 85 c0 75 38 55 48
---[ end trace 26df9e5df4bba4ac ]---
This splat cannot be generated by expedited grace periods because they
always invoke resched_cpu() on the current CPU, which is good because
expedited grace periods require that resched_cpu() unconditionally
succeed. However, other parts of RCU can tolerate resched_cpu() acting
as a no-op, at least as long as it doesn't happen too often.
This commit therefore makes resched_cpu() invoke resched_curr() only if
the CPU is either online or is the current CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull compat and uaccess updates from Al Viro:
- {get,put}_compat_sigset() series
- assorted compat ioctl stuff
- more set_fs() elimination
- a few more timespec64 conversions
- several removals of pointless access_ok() in places where it was
followed only by non-__ variants of primitives
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
coredump: call do_unlinkat directly instead of sys_unlink
fs: expose do_unlinkat for built-in callers
ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
ipmi: get rid of pointless access_ok()
pi433: sanitize ioctl
cxlflash: get rid of pointless access_ok()
mtdchar: get rid of pointless access_ok()
r128: switch compat ioctls to drm_ioctl_kernel()
selection: get rid of field-by-field copyin
VT_RESIZEX: get rid of field-by-field copyin
i2c compat ioctls: move to ->compat_ioctl()
sched_rr_get_interval(): move compat to native, get rid of set_fs()
mips: switch to {get,put}_compat_sigset()
sparc: switch to {get,put}_compat_sigset()
s390: switch to {get,put}_compat_sigset()
ppc: switch to {get,put}_compat_sigset()
parisc: switch to {get,put}_compat_sigset()
get_compat_sigset()
get rid of {get,put}_compat_itimerspec()
io_getevents: Use timespec64 to represent timeouts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS updates from David Howells:
"kAFS filesystem driver overhaul.
The major points of the overhaul are:
(1) Preliminary groundwork is laid for supporting network-namespacing
of kAFS. The remainder of the namespacing work requires some way
to pass namespace information to submounts triggered by an
automount. This requires something like the mount overhaul that's
in progress.
(2) sockaddr_rxrpc is used in preference to in_addr for holding
addresses internally and add support for talking to the YFS VL
server. With this, kAFS can do everything over IPv6 as well as
IPv4 if it's talking to servers that support it.
(3) Callback handling is overhauled to be generally passive rather
than active. 'Callbacks' are promises by the server to tell us
about data and metadata changes. Callbacks are now checked when
we next touch an inode rather than actively going and looking for
it where possible.
(4) File access permit caching is overhauled to store the caching
information per-inode rather than per-directory, shared over
subordinate files. Whilst older AFS servers only allow ACLs on
directories (shared to the files in that directory), newer AFS
servers break that restriction.
To improve memory usage and to make it easier to do mass-key
removal, permit combinations are cached and shared.
(5) Cell database management is overhauled to allow lighter locks to
be used and to make cell records autonomous state machines that
look after getting their own DNS records and cleaning themselves
up, in particular preventing races in acquiring and relinquishing
the fscache token for the cell.
(6) Volume caching is overhauled. The afs_vlocation record is got rid
of to simplify things and the superblock is now keyed on the cell
and the numeric volume ID only. The volume record is tied to a
superblock and normal superblock management is used to mediate
the lifetime of the volume fscache token.
(7) File server record caching is overhauled to make server records
independent of cells and volumes. A server can be in multiple
cells (in such a case, the administrator must make sure that the
VL services for all cells correctly reflect the volumes shared
between those cells).
Server records are now indexed using the UUID of the server
rather than the address since a server can have multiple
addresses.
(8) File server rotation is overhauled to handle VMOVED, VBUSY (and
similar), VOFFLINE and VNOVOL indications and to handle rotation
both of servers and addresses of those servers. The rotation will
also wait and retry if the server says it is busy.
(9) Data writeback is overhauled. Each inode no longer stores a list
of modified sections tagged with the key that authorised it in
favour of noting the modified region of a page in page->private
and storing a list of keys that made modifications in the inode.
This simplifies things and allows other keys to be used to
actually write to the server if a key that made a modification
becomes useless.
(10) Writable mmap() is implemented. This allows a kernel to be build
entirely on AFS.
Note that Pre AFS-3.4 servers are no longer supported, though this can
be added back if necessary (AFS-3.4 was released in 1998)"
* tag 'afs-next-20171113' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (35 commits)
afs: Protect call->state changes against signals
afs: Trace page dirty/clean
afs: Implement shared-writeable mmap
afs: Get rid of the afs_writeback record
afs: Introduce a file-private data record
afs: Use a dynamic port if 7001 is in use
afs: Fix directory read/modify race
afs: Trace the sending of pages
afs: Trace the initiation and completion of client calls
afs: Fix documentation on # vs % prefix in mount source specification
afs: Fix total-length calculation for multiple-page send
afs: Only progress call state at end of Tx phase from rxrpc callback
afs: Make use of the YFS service upgrade to fully support IPv6
afs: Overhaul volume and server record caching and fileserver rotation
afs: Move server rotation code into its own file
afs: Add an address list concept
afs: Overhaul cell database management
afs: Overhaul permit caching
afs: Overhaul the callback handling
afs: Rename struct afs_call server member to cm_server
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"Cgroup2 cpu controller support is finally merged.
- Basic cpu statistics support to allow monitoring by default without
the CPU controller enabled.
- cgroup2 cpu controller support.
- /sys/kernel/cgroup files to help dealing with new / optional
features"
* 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: export list of cgroups v2 features using sysfs
cgroup: export list of delegatable control files using sysfs
cgroup: mark @cgrp __maybe_unused in cpu_stat_show()
MAINTAINERS: relocate cpuset.c
cgroup, sched: Move basic cpu stats from cgroup.stat to cpu.stat
sched: Implement interface for cgroup unified hierarchy
sched: Misc preps for cgroup unified hierarchy interface
sched/cputime: Add dummy cputime_adjust() implementation for CONFIG_VIRT_CPU_ACCOUNTING_NATIVE
cgroup: statically initialize init_css_set->dfl_cgrp
cgroup: Implement cgroup2 basic CPU usage accounting
cpuacct: Introduce cgroup_account_cputime[_field]()
sched/cputime: Expose cputime_adjust()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main updates in this cycle were:
- Group balancing enhancements and cleanups (Brendan Jackman)
- Move CPU isolation related functionality into its separate
kernel/sched/isolation.c file, with related 'housekeeping_*()'
namespace and nomenclature et al. (Frederic Weisbecker)
- Improve the interactive/cpu-intense fairness calculation (Josef
Bacik)
- Improve the PELT code and related cleanups (Peter Zijlstra)
- Improve the logic of pick_next_task_fair() (Uladzislau Rezki)
- Improve the RT IPI based balancing logic (Steven Rostedt)
- Various micro-optimizations:
- better !CONFIG_SCHED_DEBUG optimizations (Patrick Bellasi)
- better idle loop (Cheng Jian)
- ... plus misc fixes, cleanups and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/core: Optimize sched_feat() for !CONFIG_SCHED_DEBUG builds
sched/sysctl: Fix attributes of some extern declarations
sched/isolation: Document isolcpus= boot parameter flags, mark it deprecated
sched/isolation: Add basic isolcpus flags
sched/isolation: Move isolcpus= handling to the housekeeping code
sched/isolation: Handle the nohz_full= parameter
sched/isolation: Introduce housekeeping flags
sched/isolation: Split out new CONFIG_CPU_ISOLATION=y config from CONFIG_NO_HZ_FULL
sched/isolation: Rename is_housekeeping_cpu() to housekeeping_cpu()
sched/isolation: Use its own static key
sched/isolation: Make the housekeeping cpumask private
sched/isolation: Provide a dynamic off-case to housekeeping_any_cpu()
sched/isolation, watchdog: Use housekeeping_cpumask() instead of ad-hoc version
sched/isolation: Move housekeeping related code to its own file
sched/idle: Micro-optimize the idle loop
sched/isolcpus: Fix "isolcpus=" boot parameter handling when !CONFIG_CPUMASK_OFFSTACK
x86/tsc: Append the 'tsc=' description for the 'tsc=unstable' boot parameter
sched/rt: Simplify the IPI based RT balancing logic
block/ioprio: Use a helper to check for RT prio
sched/rt: Add a helper to test for a RT task
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle are:
- Documentation updates
- RCU CPU stall-warning updates
- Torture-test updates
- Miscellaneous fixes
Size wise the biggest updates are to documentation. Excluding
documentation most of the code increase comes from a single commit
which expands debugging"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
srcu: Add parameters to SRCU docbook comments
doc: Rewrite confusing statement about memory barriers
memory-barriers.txt: Fix typo in pairing example
rcu/segcblist: Include rcupdate.h
rcu: Add extended-quiescent-state testing advice
rcu: Suppress lockdep false-positive ->boost_mtx complaints
rcu: Do not include rtmutex_common.h unconditionally
torture: Provide TMPDIR environment variable to specify tmpdir
rcutorture: Dump writer stack if stalled
rcutorture: Add interrupt-disable capability to stall-warning tests
rcu: Suppress RCU CPU stall warnings while dumping trace
rcu: Turn off tracing before dumping trace
rcu: Make RCU CPU stall warnings check for irq-disabled CPUs
sched,rcu: Make cond_resched() provide RCU quiescent state
sched: Make resched_cpu() unconditional
irq_work: Map irq_work_on_queue() to irq_work_on() in !SMP
rcu: Create call_rcu_tasks() kthread at boot time
rcu: Fix up pending cbs check in rcu_prepare_for_idle
memory-barriers: Rework multicopy-atomicity section
memory-barriers: Replace uses of "transitive"
...
|
|
Make wait_on_atomic_t() pass the TASK_* mode onto its action function as an
extra argument and make it 'unsigned int throughout.
Also, consolidate a bunch of identical action functions into a default
function that can do the appropriate thing for the mode.
Also, change the argument name in the bit_wait*() function declarations to
reflect the fact that it's the mode and not the bit number.
[Peter Z gives this a grudging ACK, but thinks that the whole atomic_t wait
should be done differently, though he's not immediately sure as to how]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
cc: Ingo Molnar <mingo@kernel.org>
|
|
* pm-cpufreq-sched:
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
* pm-opp:
PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Support updating performance state of device's power domain
PM / OPP: add missing of_node_put() for of_get_cpu_node()
PM / OPP: Rename dev_pm_opp_register_put_opp_helper()
PM / OPP: Add missing of_node_put(np)
PM / OPP: Move error message to debug level
PM / OPP: Use snprintf() to avoid kasprintf() and kfree()
PM / OPP: Move the OPP directory out of power/
|
|
When the kernel is compiled with !CONFIG_SCHED_DEBUG support, we expect that
all SCHED_FEAT are turned into compile time constants being propagated
to support compiler optimizations.
Specifically, we expect that code blocks like this:
if (sched_feat(FEATURE_NAME) [&& <other_conditions>]) {
/* FEATURE CODE */
}
are turned into dead-code in case FEATURE_NAME defaults to FALSE, and thus
being removed by the compiler from the finale image.
For this mechanism to properly work it's required for the compiler to
have full access, from each translation unit, to whatever is the value
defined by the sched_feat macro. This macro is defined as:
#define sched_feat(x) (sysctl_sched_features & (1UL << __SCHED_FEAT_##x))
and thus, the compiler can optimize that code only if the value of
sysctl_sched_features is visible within each translation unit.
Since:
029632fbb ("sched: Make separate sched*.c translation units")
the scheduler code has been split into separate translation units
however the definition of sysctl_sched_features is part of
kernel/sched/core.c while, for all the other scheduler modules, it is
visible only via kernel/sched/sched.h as an:
extern const_debug unsigned int sysctl_sched_features
Unfortunately, an extern reference does not allow the compiler to apply
constants propagation. Thus, on !CONFIG_SCHED_DEBUG kernel we still end up
with code to load a memory reference and (eventually) doing an unconditional
jump of a chunk of code.
This mechanism is unavoidable when sched_features can be turned on and off at
run-time. However, this is not the case for "production" kernels compiled with
!CONFIG_SCHED_DEBUG. In this case, sysctl_sched_features is just a constant value
which cannot be changed at run-time and thus memory loads and jumps can be
avoided altogether.
This patch fixes the case of !CONFIG_SCHED_DEBUG kernel by declaring a local version
of the sysctl_sched_features constant for each translation unit. This will
ultimately allow the compiler to perform constants propagation and dead-code
pruning.
Tests have been done, with !CONFIG_SCHED_DEBUG on a v4.14-rc8 with and without
the patch, by running 30 iterations of:
perf bench sched messaging --pipe --thread --group 4 --loop 50000
on a 40 cores Intel(R) Xeon(R) CPU E5-2690 v2 @ 3.00GHz using the
powersave governor to rule out variations due to frequency scaling.
Statistics on the reported completion time:
count mean std min 99% max
v4.14-rc8 30.0 15.7831 0.176032 15.442 16.01226 16.014
v4.14-rc8+patch 30.0 15.5033 0.189681 15.232 15.93938 15.962
... show a 1.8% speedup on average completion time and 0.5% speedup in the
99 percentile.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/20171108184101.16006-1-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
* pm-cpufreq-sched:
cpufreq: schedutil: Examine the correct CPU when we update util
|
|
'cached_raw_freq' is used to get the next frequency quickly but should
always be in sync with sg_policy->next_freq. There is a case where it is
not and in such cases it should be reset to avoid switching to incorrect
frequencies.
Consider this case for example:
- policy->cur is 1.2 GHz (Max)
- New request comes for 780 MHz and we store that in cached_raw_freq.
- Based on 780 MHz, we calculate the effective frequency as 800 MHz.
- We then see the CPU wasn't idle recently and choose to keep the next
freq as 1.2 GHz.
- Now we have cached_raw_freq is 780 MHz and sg_policy->next_freq is
1.2 GHz.
- Now if the utilization doesn't change in then next request, then the
next target frequency will still be 780 MHz and it will match with
cached_raw_freq. But we will choose 1.2 GHz instead of 800 MHz here.
Fixes: b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.12+ <stable@vger.kernel.org> # 4.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use lockdep to check that IRQs are enabled or disabled as expected. This
way the sanity check only shows overhead when concurrency correctness
debug code is enabled.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David S . Miller <davem@davemloft.net>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1509980490-4285-12-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
After commit 674e75411fc2 (sched: cpufreq: Allow remote cpufreq
callbacks) we stopped to always read the utilization for the CPU we
are running the governor on, and instead we read it for the CPU
which we've been told has updated utilization. This is stored in
sugov_cpu->cpu.
The value is set in sugov_register() but we clear it in sugov_start()
which leads to always looking at the utilization of CPU0 instead of
the correct one.
Fix this by consolidating the initialization code into sugov_start().
Fixes: 674e75411fc2 (sched: cpufreq: Allow remote cpufreq callbacks)
Signed-off-by: Chris Redpath <chris.redpath@arm.com>
Reviewed-by: Patrick Bellasi <patrick.bellasi@arm.com>
Reviewed-by: Brendan Jackman <brendan.jackman@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
