| Age | Commit message (Collapse) | Author |
|---|
|
Split the logic for getting next timer interrupt (no matter of recalculated
or already stored in base->next_expiry) into a separate function named
next_timer_interrupt(). Make it available to local call sites only.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-10-anna-maria@linutronix.de
|
|
The logic for raising a softirq the way it is implemented right now, is
readable for two timer bases. When increasing the number of timer bases,
code gets harder to read. With the introduction of the timer migration
hierarchy, there will be three timer bases.
Therefore restructure the code to use a loop. No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-9-anna-maria@linutronix.de
|
|
When adding a timer to the timer wheel using add_timer_on(), it is an
implicitly pinned timer. With the timer pull at expiry time model in place,
the TIMER_PINNED flag is required to make sure timers end up in proper
base.
Set the TIMER_PINNED flag unconditionally when add_timer_on() is executed.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-8-anna-maria@linutronix.de
|
|
A timer might be used as a pinned timer (using add_timer_on()) and later on
as non-pinned timer using add_timer(). When the "NOHZ timer pull at expiry
model" is in place, the TIMER_PINNED flag is required to be used whenever a
timer needs to expire on a dedicated CPU. Otherwise the flag must not be
set if expiration on a dedicated CPU is not required.
add_timer_on()'s behavior will be changed during the preparation patches
for the "NOHZ timer pull at expiry model" to unconditionally set the
TIMER_PINNED flag. To be able to clear/ set the flag when queueing a
timer, two variants of add_timer() are introduced.
This is a preparatory step and has no functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-6-anna-maria@linutronix.de
|
|
When tick is stopped also the timer base is_idle flag is set. When
reentering timer_base_try_to_set_idle() with the tick stopped, there is no
need to check whether the timer base needs to be set idle again. When a
timer was enqueued in the meantime, this is already handled by the
tick_nohz_next_event() call which was executed before
tick_nohz_stop_tick().
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-5-anna-maria@linutronix.de
|
|
The timer base is marked idle when get_next_timer_interrupt() is
executed. But the decision whether the tick will be stopped and whether the
system is able to go idle is done later. When the timer bases is marked
idle and a new first timer is enqueued remote an IPI is raised. Even if it
is not required because the tick is not stopped and the timer base is
evaluated again at the next tick.
To prevent this, the timer base is marked idle in tick_nohz_stop_tick() and
get_next_timer_interrupt() is streamlined by only looking for the next timer
interrupt. All other work is postponed to timer_base_try_to_set_idle() which is
called by tick_nohz_stop_tick(). timer_base_try_to_set_idle() never resets
timer_base::is_idle state. This is done when the tick is restarted via
tick_nohz_restart_sched_tick().
With this, tick_sched::tick_stopped and timer_base::is_idle are always in
sync. So there is no longer the need to execute timer_clear_idle() in
tick_nohz_idle_retain_tick(). This was required before, as
tick_nohz_next_event() set timer_base::is_idle even if the tick would not be
stopped. So timer_clear_idle() is only executed, when timer base is idle. So the
check whether timer base is idle, is now no longer required as well.
While at it fix some nearby whitespace damage as well.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-4-anna-maria@linutronix.de
|
|
Split out get_next_timer_interrupt() to be able to extend it and make it
reusable for other call sites.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-3-anna-maria@linutronix.de
|
|
get_next_timer_interrupt() contains two parts for the next timer interrupt
calculation. Those two parts are separated by forwarding the base
clock. But the second part does not depend on the forwarded base
clock.
Therefore restructure get_next_timer_interrupt() to keep things together
which belong together.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240221090548.36600-2-anna-maria@linutronix.de
|
|
On a 8-socket server the TSC is wrongly marked as 'unstable' and disabled
during boot time on about one out of 120 boot attempts:
clocksource: timekeeping watchdog on CPU227: wd-tsc-wd excessive read-back delay of 153560ns vs. limit of 125000ns,
wd-wd read-back delay only 11440ns, attempt 3, marking tsc unstable
tsc: Marking TSC unstable due to clocksource watchdog
TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
sched_clock: Marking unstable (119294969739, 159204297)<-(125446229205, -5992055152)
clocksource: Checking clocksource tsc synchronization from CPU 319 to CPUs 0,99,136,180,210,542,601,896.
clocksource: Switched to clocksource hpet
The reason is that for platform with a large number of CPUs, there are
sporadic big or huge read latencies while reading the watchog/clocksource
during boot or when system is under stress work load, and the frequency and
maximum value of the latency goes up with the number of online CPUs.
The cCurrent code already has logic to detect and filter such high latency
case by reading the watchdog twice and checking the two deltas. Due to the
randomness of the latency, there is a low probabilty that the first delta
(latency) is big, but the second delta is small and looks valid. The
watchdog code retries the readouts by default twice, which is not
necessarily sufficient for systems with a large number of CPUs.
There is a command line parameter 'max_cswd_read_retries' which allows to
increase the number of retries, but that's not user friendly as it needs to
be tweaked per system. As the number of required retries is proportional to
the number of online CPUs, this parameter can be calculated at runtime.
Scale and enlarge the number of retries according to the number of online
CPUs and remove the command line parameter completely.
[ tglx: Massaged change log and comments ]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jin Wang <jin1.wang@intel.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240221060859.1027450-1-feng.tang@intel.com
|
|
'days' is a s64 (from div_s64), and so should use a %lld specifier.
This was found by extending KUnit's assertion macros to use gcc's
__printf attribute.
Fixes: 276010551664 ("time: Improve performance of time64_to_tm()")
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240221092728.1281499-5-davidgow@google.com
|
|
There's a conflict between this recent upstream fix:
dad6a09f3148 ("hrtimer: Report offline hrtimer enqueue")
and a pending commit in the timers tree:
1a4729ecafc2 ("hrtimers: Move hrtimer base related definitions into hrtimer_defs.h")
Resolve it by applying the upstream fix to the new <linux/hrtimer_defs.h> header.
Conflict:
include/linux/hrtimer.h
Semantic conflict:
include/linux/hrtimer_defs.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
So far, get_device_system_crosststamp() unconditionally passes
system_counterval.cycles to timekeeping_cycles_to_ns(). But when
interpolating system time (do_interp == true), system_counterval.cycles is
before tkr_mono.cycle_last, contrary to the timekeeping_cycles_to_ns()
expectations.
On x86, CONFIG_CLOCKSOURCE_VALIDATE_LAST_CYCLE will mitigate on
interpolating, setting delta to 0. With delta == 0, xtstamp->sys_monoraw
and xtstamp->sys_realtime are then set to the last update time, as
implicitly expected by adjust_historical_crosststamp(). On other
architectures, the resulting nonsense xtstamp->sys_monoraw and
xtstamp->sys_realtime corrupt the xtstamp (ts) adjustment in
adjust_historical_crosststamp().
Fix this by deriving xtstamp->sys_monoraw and xtstamp->sys_realtime from
the last update time when interpolating, by using the local variable
"cycles". The local variable already has the right value when
interpolating, unlike system_counterval.cycles.
Fixes: 2c756feb18d9 ("time: Add history to cross timestamp interface supporting slower devices")
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20231218073849.35294-4-peter.hilber@opensynergy.com
|
|
The cycle_between() helper checks if parameter test is in the open interval
(before, after). Colloquially speaking, this also applies to the counter
wrap-around special case before > after. get_device_system_crosststamp()
currently uses cycle_between() at the first call site to decide whether to
interpolate for older counter readings.
get_device_system_crosststamp() has the following problem with
cycle_between() testing against an open interval: Assume that, by chance,
cycles == tk->tkr_mono.cycle_last (in the following, "cycle_last" for
brevity). Then, cycle_between() at the first call site, with effective
argument values cycle_between(cycle_last, cycles, now), returns false,
enabling interpolation. During interpolation,
get_device_system_crosststamp() will then call cycle_between() at the
second call site (if a history_begin was supplied). The effective argument
values are cycle_between(history_begin->cycles, cycles, cycles), since
system_counterval.cycles == interval_start == cycles, per the assumption.
Due to the test against the open interval, cycle_between() returns false
again. This causes get_device_system_crosststamp() to return -EINVAL.
This failure should be avoided, since get_device_system_crosststamp() works
both when cycles follows cycle_last (no interpolation), and when cycles
precedes cycle_last (interpolation). For the case cycles == cycle_last,
interpolation is actually unneeded.
Fix this by changing cycle_between() into timestamp_in_interval(), which
now checks against the closed interval, rather than the open interval.
This changes the get_device_system_crosststamp() behavior for three corner
cases:
1. Bypass interpolation in the case cycles == tk->tkr_mono.cycle_last,
fixing the problem described above.
2. At the first timestamp_in_interval() call site, cycles == now no longer
causes failure.
3. At the second timestamp_in_interval() call site, history_begin->cycles
== system_counterval.cycles no longer causes failure.
adjust_historical_crosststamp() also works for this corner case,
where partial_history_cycles == total_history_cycles.
These behavioral changes should not cause any problems.
Fixes: 2c756feb18d9 ("time: Add history to cross timestamp interface supporting slower devices")
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231218073849.35294-3-peter.hilber@opensynergy.com
|
|
cycle_between() decides whether get_device_system_crosststamp() will
interpolate for older counter readings.
cycle_between() yields wrong results for a counter wrap-around where after
< before < test, and for the case after < test < before.
Fix the comparison logic.
Fixes: 2c756feb18d9 ("time: Add history to cross timestamp interface supporting slower devices")
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20231218073849.35294-2-peter.hilber@opensynergy.com
|
|
timer_base struct lacks description of struct members. Important struct
member information is sprinkled in comments or in code all over the place.
Collect information and write struct description to keep track of most
important information in a single place.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-5-anna-maria@linutronix.de
|
|
The return value of tick_nohz_next_event() is not obvious at the first
glance. Add a kernel-doc compatible function description which also covers
return values.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-4-anna-maria@linutronix.de
|
|
Documentation of functions lacks the annotations which are used by
kernel-doc and *.rst to make appearance in rendered documents more
user-friendly.
Use those annotations to improve user-friendliness. While at it prevent
duplication of comments and use a reference instead.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-3-anna-maria@linutronix.de
|
|
Clocksource pointers can be problematic to obtain for drivers which are not
clocksource drivers themselves. In particular, the RFC virtio_rtc driver
[1] would require a new helper function to obtain a pointer to the ARM
Generic Timer clocksource. The ptp_kvm driver also required a similar
workaround.
Address this by evaluating the clocksource ID, rather than the clocksource
pointer, of struct system_counterval_t. By this, setting the clocksource
pointer becomes unneeded, and get_device_system_crosststamp() callers will
no longer need to supply clocksource pointers.
All relevant clocksource drivers provide the ID, so this change is not
changing the behaviour.
[1] https://lore.kernel.org/lkml/20231218073849.35294-1-peter.hilber@opensynergy.com/
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240201010453.2212371-7-peter.hilber@opensynergy.com
|
|
Now that the driver core can properly handle constant struct bus_type,
move the clockevents_subsys variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-time-v1-2-207ec18e24b8@marliere.net
|
|
Now that the driver core can properly handle constant struct bus_type,
move the clocksource_subsys variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-time-v1-1-207ec18e24b8@marliere.net
|
|
The hrtimers migration on CPU-down hotplug process has been moved
earlier, before the CPU actually goes to die. This leaves a small window
of opportunity to queue an hrtimer in a blind spot, leaving it ignored.
For example a practical case has been reported with RCU waking up a
SCHED_FIFO task right before the CPUHP_AP_IDLE_DEAD stage, queuing that
way a sched/rt timer to the local offline CPU.
Make sure such situations never go unnoticed and warn when that happens.
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240129235646.3171983-4-boqun.feng@gmail.com
|
|
Commit 71fee48f ("tick-sched: Fix idle and iowait sleeptime accounting vs
CPU hotplug") preserved total idle sleep time and iowait sleeptime across
CPU hotplug events.
Similar reasoning applies to the number of idle calls and idle sleeps to
get the proper average of sleep time per idle invocation.
Preserve those fields too.
Fixes: 71fee48f ("tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug")
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240122233534.3094238-1-tim.c.chen@linux.intel.com
|
|
There have been reports of the watchdog marking clocksources unstable on
machines with 8 NUMA nodes:
clocksource: timekeeping watchdog on CPU373:
Marking clocksource 'tsc' as unstable because the skew is too large:
clocksource: 'hpet' wd_nsec: 14523447520
clocksource: 'tsc' cs_nsec: 14524115132
The measured clocksource skew - the absolute difference between cs_nsec
and wd_nsec - was 668 microseconds:
cs_nsec - wd_nsec = 14524115132 - 14523447520 = 667612
The kernel used 200 microseconds for the uncertainty_margin of both the
clocksource and watchdog, resulting in a threshold of 400 microseconds (the
md variable). Both the cs_nsec and the wd_nsec value indicate that the
readout interval was circa 14.5 seconds. The observed behaviour is that
watchdog checks failed for large readout intervals on 8 NUMA node
machines. This indicates that the size of the skew was directly proportinal
to the length of the readout interval on those machines. The measured
clocksource skew, 668 microseconds, was evaluated against a threshold (the
md variable) that is suited for readout intervals of roughly
WATCHDOG_INTERVAL, i.e. HZ >> 1, which is 0.5 second.
The intention of 2e27e793e280 ("clocksource: Reduce clocksource-skew
threshold") was to tighten the threshold for evaluating skew and set the
lower bound for the uncertainty_margin of clocksources to twice
WATCHDOG_MAX_SKEW. Later in c37e85c135ce ("clocksource: Loosen clocksource
watchdog constraints"), the WATCHDOG_MAX_SKEW constant was increased to
125 microseconds to fit the limit of NTP, which is able to use a
clocksource that suffers from up to 500 microseconds of skew per second.
Both the TSC and the HPET use default uncertainty_margin. When the
readout interval gets stretched the default uncertainty_margin is no
longer a suitable lower bound for evaluating skew - it imposes a limit
that is far stricter than the skew with which NTP can deal.
The root causes of the skew being directly proportinal to the length of
the readout interval are:
* the inaccuracy of the shift/mult pairs of clocksources and the watchdog
* the conversion to nanoseconds is imprecise for large readout intervals
Prevent this by skipping the current watchdog check if the readout
interval exceeds 2 * WATCHDOG_INTERVAL. Considering the maximum readout
interval of 2 * WATCHDOG_INTERVAL, the current default uncertainty margin
(of the TSC and HPET) corresponds to a limit on clocksource skew of 250
ppm (microseconds of skew per second). To keep the limit imposed by NTP
(500 microseconds of skew per second) for all possible readout intervals,
the margins would have to be scaled so that the threshold value is
proportional to the length of the actual readout interval.
As for why the readout interval may get stretched: Since the watchdog is
executed in softirq context the expiration of the watchdog timer can get
severely delayed on account of a ksoftirqd thread not getting to run in a
timely manner. Surely, a system with such belated softirq execution is not
working well and the scheduling issue should be looked into but the
clocksource watchdog should be able to deal with it accordingly.
Fixes: 2e27e793e280 ("clocksource: Reduce clocksource-skew threshold")
Suggested-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jiri Wiesner <jwiesner@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240122172350.GA740@incl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
|
|
When offlining and onlining CPUs the overall reported idle and iowait
times as reported by /proc/stat jump backward and forward:
cpu 132 0 176 225249 47 6 6 21 0 0
cpu0 80 0 115 112575 33 3 4 18 0 0
cpu1 52 0 60 112673 13 3 1 2 0 0
cpu 133 0 177 226681 47 6 6 21 0 0
cpu0 80 0 116 113387 33 3 4 18 0 0
cpu 133 0 178 114431 33 6 6 21 0 0 <---- jump backward
cpu0 80 0 116 114247 33 3 4 18 0 0
cpu1 52 0 61 183 0 3 1 2 0 0 <---- idle + iowait start with 0
cpu 133 0 178 228956 47 6 6 21 0 0 <---- jump forward
cpu0 81 0 117 114929 33 3 4 18 0 0
Reason for this is that get_idle_time() in fs/proc/stat.c has different
sources for both values depending on if a CPU is online or offline:
- if a CPU is online the values may be taken from its per cpu
tick_cpu_sched structure
- if a CPU is offline the values are taken from its per cpu cpustat
structure
The problem is that the per cpu tick_cpu_sched structure is set to zero on
CPU offline. See tick_cancel_sched_timer() in kernel/time/tick-sched.c.
Therefore when a CPU is brought offline and online afterwards both its idle
and iowait sleeptime will be zero, causing a jump backward in total system
idle and iowait sleeptime. In a similar way if a CPU is then brought
offline again the total idle and iowait sleeptimes will jump forward.
It looks like this behavior was introduced with commit 4b0c0f294f60
("tick: Cleanup NOHZ per cpu data on cpu down").
This was only noticed now on s390, since we switched to generic idle time
reporting with commit be76ea614460 ("s390/idle: remove arch_cpu_idle_time()
and corresponding code").
Fix this by preserving the values of idle_sleeptime and iowait_sleeptime
members of the per-cpu tick_sched structure on CPU hotplug.
Fixes: 4b0c0f294f60 ("tick: Cleanup NOHZ per cpu data on cpu down")
Reported-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20240115163555.1004144-1-hca@linux.ibm.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer subsystem updates from Ingo Molnar:
- Various preparatory cleanups & enhancements of the timer-wheel code,
in preparation for the WIP 'pull timers at expiry' timer migration
model series (which will replace the current 'push timers at enqueue'
migration model), by Anna-Maria Behnsen:
- Update comments and clean up confusing variable names
- Add debug check to warn about time travel
- Improve/expand timer-wheel tracepoints
- Optimize away unnecessary IPIs for deferrable timers
- Restructure & clean up next_expiry_recalc()
- Clean up forward_timer_base()
- Introduce __forward_timer_base() and use it to simplify and
micro-optimize get_next_timer_interrupt()
- Restructure the get_next_timer_interrupt()'s idle logic for better
readability and to enable a minor optimization.
- Fix the nextevt calculation when no timers are pending
- Fix the sysfs_get_uname() prototype declaration
* tag 'timers-core-2024-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix nextevt calculation when no timers are pending
timers: Rework idle logic
timers: Use already existing function for forwarding timer base
timers: Split out forward timer base functionality
timers: Clarify check in forward_timer_base()
timers: Move store of next event into __next_timer_interrupt()
timers: Do not IPI for deferrable timers
tracing/timers: Add tracepoint for tracking timer base is_idle flag
tracing/timers: Enhance timer_start tracepoint
tick-sched: Warn when next tick seems to be in the past
tick/sched: Cleanup confusing variables
tick-sched: Fix function names in comments
time: Make sysfs_get_uname() function visible in header
|
|
Only the posix timer system calls use this (when the posix timer support
is disabled, which does not actually happen in any normal case), because
they had debug code to print out a warning about missing system calls.
Get rid of that special case, and just use the standard COND_SYSCALL
interface that creates weak system call stubs that return -ENOSYS for
when the system call does not exist.
This fixes a kCFI issue with the SYS_NI() hackery:
CFI failure at int80_emulation+0x67/0xb0 (target: sys_ni_posix_timers+0x0/0x70; expected type: 0xb02b34d9)
WARNING: CPU: 0 PID: 48 at int80_emulation+0x67/0xb0
Reported-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When no timer is queued into an empty timer base, the next_expiry will not
be updated. It was originally calculated as
base->clk + NEXT_TIMER_MAX_DELTA
When the timer base stays empty long enough (> NEXT_TIMER_MAX_DELTA), the
next_expiry value of the empty base suggests that there is a timer pending
soon. This might be more a kind of a theoretical problem, but the fix
doesn't hurt.
Use only base->next_expiry value as nextevt when timers are
pending. Otherwise nextevt will be jiffies + NEXT_TIMER_MAX_DELTA. As all
information is in place, update base->next_expiry value of the empty timer
base as well.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-13-anna-maria@linutronix.de
|
|
To improve readability of the code, split base->idle calculation and
expires calculation into separate parts. While at it, update the comment
about timer base idle marking.
Thereby the following subtle change happens if the next event is just one
jiffy ahead and the tick was already stopped: Originally base->is_idle
remains true in this situation. Now base->is_idle turns to false. This may
spare an IPI if a timer is enqueued remotely to an idle CPU that is going
to tick on the next jiffy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-12-anna-maria@linutronix.de
|
|
There is an already existing function for forwarding the timer
base. Forwarding the timer base is implemented directly in
get_next_timer_interrupt() as well.
Remove the code duplication and invoke __forward_timer_base() instead.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-11-anna-maria@linutronix.de
|
|
Forwarding timer base is done when the next expiry value is calculated and
when a new timer is enqueued. When the next expiry value is calculated the
jiffies value is already available and does not need to be reread a second
time.
Splitting out the forward timer base functionality to make it executable
via both contextes - those where jiffies are already known and those, where
jiffies need to be read.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-10-anna-maria@linutronix.de
|
|
The current check whether a forward of the timer base is required can be
simplified by using an already existing comparison function which is easier
to read. The related comment is outdated and was not updated when the check
changed in commit 36cd28a4cdd0 ("timers: Lower base clock forwarding
threshold").
Use time_before_eq() for the check and replace the comment by copying the
comment from the same check inside get_next_timer_interrupt(). Move the
precious information of the outdated comment to the proper place in
__run_timers().
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-9-anna-maria@linutronix.de
|
|
Both call sites of __next_timer_interrupt() store the return value directly
in base->next_expiry. Move the store into __next_timer_interrupt() and to
make its purpose more clear, rename the function to next_expiry_recalc().
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-8-anna-maria@linutronix.de
|
|
Deferrable timers do not prevent CPU from going idle and are not taken into
account on idle path. Sending an IPI to a remote CPU when a new first
deferrable timer was enqueued will wake up the remote CPU but nothing will
be done regarding the deferrable timers.
Drop IPI completely when a new first deferrable timer was enqueued.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-7-anna-maria@linutronix.de
|
|
When debugging timer code the timer tracepoints are very important. There
is no tracepoint when the is_idle flag of the timer base changes. Instead
of always adding manually trace_printk(), add tracepoints which can be
easily enabled whenever required.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-6-anna-maria@linutronix.de
|
|
For starting a timer, the timer is enqueued into a bucket of the timer
wheel. The bucket expiry is the defacto expiry of the timer but it is not
equal the timer expiry because of increasing granularity when bucket is in
a higher level of the wheel. To be able to figure out in a trace whether a
timer expired in time or not, the bucket expiry time is required as well.
Add bucket expiry time to the timer_start tracepoint and thereby simplify
the arguments.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-5-anna-maria@linutronix.de
|
|
When the next tick is in the past, the delta between basemono and the next
tick gets negativ. But the next tick should never be in the past. The
negative effect of a wrong next tick might be a stop of the tick and timers
might expire late.
To prevent expensive debugging when changing underlying code, add a
WARN_ON_ONCE into this code path. To prevent complete misbehaviour, also
reset next_tick to basemono in this case.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-4-anna-maria@linutronix.de
|
|
tick_nohz_stop_tick() contains the expires (u64 variable) and tick
(ktime_t) variable. In the beginning the value of expires is written to
tick. Afterwards none of the variables is changed. They are only used for
checks.
Drop the not required variable tick and use always expires instead.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-3-anna-maria@linutronix.de
|
|
When referencing functions in comments, it might be helpful to use full
function names (including the prefix) to be able to find it when grepping.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20231201092654.34614-2-anna-maria@linutronix.de
|
|
This function is defined globally in clocksource.c and used conditionally
in clockevent.c, which the declaration hidden when clockevent support
is disabled. This causes a harmless warning in the definition:
kernel/time/clocksource.c:1324:9: warning: no previous prototype for 'sysfs_get_uname' [-Wmissing-prototypes]
1324 | ssize_t sysfs_get_uname(const char *buf, char *dst, size_t cnt)
Move the declaration out of the #ifdef so it is always visible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231108125843.3806765-5-arnd@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Do the push of pending hrtimers away from a CPU which is being
offlined earlier in the offlining process in order to prevent a
deadlock
* tag 'timers_urgent_for_v6.7_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimers: Push pending hrtimers away from outgoing CPU earlier
|
|
2b8272ff4a70 ("cpu/hotplug: Prevent self deadlock on CPU hot-unplug")
solved the straight forward CPU hotplug deadlock vs. the scheduler
bandwidth timer. Yu discovered a more involved variant where a task which
has a bandwidth timer started on the outgoing CPU holds a lock and then
gets throttled. If the lock required by one of the CPU hotplug callbacks
the hotplug operation deadlocks because the unthrottling timer event is not
handled on the dying CPU and can only be recovered once the control CPU
reaches the hotplug state which pulls the pending hrtimers from the dead
CPU.
Solve this by pushing the hrtimers away from the dying CPU in the dying
callbacks. Nothing can queue a hrtimer on the dying CPU at that point because
all other CPUs spin in stop_machine() with interrupts disabled and once the
operation is finished the CPU is marked offline.
Reported-by: Yu Liao <liaoyu15@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Liu Tie <liutie4@huawei.com>
Link: https://lore.kernel.org/r/87a5rphara.ffs@tglx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Support usec resolution of TCP timestamps, enabled selectively by a
route attribute.
- Defer regular TCP ACK while processing socket backlog, try to send
a cumulative ACK at the end. Increase single TCP flow performance
on a 200Gbit NIC by 20% (100Gbit -> 120Gbit).
- The Fair Queuing (FQ) packet scheduler:
- add built-in 3 band prio / WRR scheduling
- support bypass if the qdisc is mostly idle (5% speed up for TCP RR)
- improve inactive flow reporting
- optimize the layout of structures for better cache locality
- Support TCP Authentication Option (RFC 5925, TCP-AO), a more modern
replacement for the old MD5 option.
- Add more retransmission timeout (RTO) related statistics to
TCP_INFO.
- Support sending fragmented skbs over vsock sockets.
- Make sure we send SIGPIPE for vsock sockets if socket was
shutdown().
- Add sysctl for ignoring lower limit on lifetime in Router
Advertisement PIO, based on an in-progress IETF draft.
- Add sysctl to control activation of TCP ping-pong mode.
- Add sysctl to make connection timeout in MPTCP configurable.
- Support rcvlowat and notsent_lowat on MPTCP sockets, to help apps
limit the number of wakeups.
- Support netlink GET for MDB (multicast forwarding), allowing user
space to request a single MDB entry instead of dumping the entire
table.
- Support selective FDB flushing in the VXLAN tunnel driver.
- Allow limiting learned FDB entries in bridges, prevent OOM attacks.
- Allow controlling via configfs netconsole targets which were
created via the kernel cmdline at boot, rather than via configfs at
runtime.
- Support multiple PTP timestamp event queue readers with different
filters.
- MCTP over I3C.
BPF:
- Add new veth-like netdevice where BPF program defines the logic of
the xmit routine. It can operate in L3 and L2 mode.
- Support exceptions - allow asserting conditions which should never
be true but are hard for the verifier to infer. With some extra
flexibility around handling of the exit / failure:
https://lwn.net/Articles/938435/
- Add support for local per-cpu kptr, allow allocating and storing
per-cpu objects in maps. Access to those objects operates on the
value for the current CPU.
This allows to deprecate local one-off implementations of per-CPU
storage like BPF_MAP_TYPE_PERCPU_CGROUP_STORAGE maps.
- Extend cgroup BPF sockaddr hooks for UNIX sockets. The use case is
for systemd to re-implement the LogNamespace feature which allows
running multiple instances of systemd-journald to process the logs
of different services.
- Enable open-coded task_vma iteration, after maple tree conversion
made it hard to directly walk VMAs in tracing programs.
- Add open-coded task, css_task and css iterator support. One of the
use cases is customizable OOM victim selection via BPF.
- Allow source address selection with bpf_*_fib_lookup().
- Add ability to pin BPF timer to the current CPU.
- Prevent creation of infinite loops by combining tail calls and
fentry/fexit programs.
- Add missed stats for kprobes to retrieve the number of missed
kprobe executions and subsequent executions of BPF programs.
- Inherit system settings for CPU security mitigations.
- Add BPF v4 CPU instruction support for arm32 and s390x.
Changes to common code:
- overflow: add DEFINE_FLEX() for on-stack definition of structs with
flexible array members.
- Process doc update with more guidance for reviewers.
Driver API:
- Simplify locking in WiFi (cfg80211 and mac80211 layers), use wiphy
mutex in most places and remove a lot of smaller locks.
- Create a common DPLL configuration API. Allow configuring and
querying state of PLL circuits used for clock syntonization, in
network time distribution.
- Unify fragmented and full page allocation APIs in page pool code.
Let drivers be ignorant of PAGE_SIZE.
- Rework PHY state machine to avoid races with calls to phy_stop().
- Notify DSA drivers of MAC address changes on user ports, improve
correctness of offloads which depend on matching port MAC
addresses.
- Allow antenna control on injected WiFi frames.
- Reduce the number of variants of napi_schedule().
- Simplify error handling when composing devlink health messages.
Misc:
- A lot of KCSAN data race "fixes", from Eric.
- A lot of __counted_by() annotations, from Kees.
- A lot of strncpy -> strscpy and printf format fixes.
- Replace master/slave terminology with conduit/user in DSA drivers.
- Handful of KUnit tests for netdev and WiFi core.
Removed:
- AppleTalk COPS.
- AppleTalk ipddp.
- TI AR7 CPMAC Ethernet driver.
Drivers:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- add a driver for the Intel E2000 IPUs
- make CRC/FCS stripping configurable
- cross-timestamping for E823 devices
- basic support for E830 devices
- use aux-bus for managing client drivers
- i40e: report firmware versions via devlink
- nVidia/Mellanox:
- support 4-port NICs
- increase max number of channels to 256
- optimize / parallelize SF creation flow
- Broadcom (bnxt):
- enhance NIC temperature reporting
- support PAM4 speeds and lane configuration
- Marvell OcteonTX2:
- PTP pulse-per-second output support
- enable hardware timestamping for VFs
- Solarflare/AMD:
- conntrack NAT offload and offload for tunnels
- Wangxun (ngbe/txgbe):
- expose HW statistics
- Pensando/AMD:
- support PCI level reset
- narrow down the condition under which skbs are linearized
- Netronome/Corigine (nfp):
- support CHACHA20-POLY1305 crypto in IPsec offload
- Ethernet NICs embedded, slower, virtual:
- Synopsys (stmmac):
- add Loongson-1 SoC support
- enable use of HW queues with no offload capabilities
- enable PPS input support on all 5 channels
- increase TX coalesce timer to 5ms
- RealTek USB (r8152): improve efficiency of Rx by using GRO frags
- xen: support SW packet timestamping
- add drivers for implementations based on TI's PRUSS (AM64x EVM)
- nVidia/Mellanox Ethernet datacenter switches:
- avoid poor HW resource use on Spectrum-4 by better block
selection for IPv6 multicast forwarding and ordering of blocks
in ACL region
- Ethernet embedded switches:
- Microchip:
- support configuring the drive strength for EMI compliance
- ksz9477: partial ACL support
- ksz9477: HSR offload
- ksz9477: Wake on LAN
- Realtek:
- rtl8366rb: respect device tree config of the CPU port
- Ethernet PHYs:
- support Broadcom BCM5221 PHYs
- TI dp83867: support hardware LED blinking
- CAN:
- add support for Linux-PHY based CAN transceivers
- at91_can: clean up and use rx-offload helpers
- WiFi:
- MediaTek (mt76):
- new sub-driver for mt7925 USB/PCIe devices
- HW wireless <> Ethernet bridging in MT7988 chips
- mt7603/mt7628 stability improvements
- Qualcomm (ath12k):
- WCN7850:
- enable 320 MHz channels in 6 GHz band
- hardware rfkill support
- enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to
make scan faster
- read board data variant name from SMBIOS
- QCN9274: mesh support
- RealTek (rtw89):
- TDMA-based multi-channel concurrency (MCC)
- Silicon Labs (wfx):
- Remain-On-Channel (ROC) support
- Bluetooth:
- ISO: many improvements for broadcast support
- mark BCM4378/BCM4387 as BROKEN_LE_CODED
- add support for QCA2066
- btmtksdio: enable Bluetooth wakeup from suspend"
* tag 'net-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1816 commits)
net: pcs: xpcs: Add 2500BASE-X case in get state for XPCS drivers
net: bpf: Use sockopt_lock_sock() in ip_sock_set_tos()
net: mana: Use xdp_set_features_flag instead of direct assignment
vxlan: Cleanup IFLA_VXLAN_PORT_RANGE entry in vxlan_get_size()
iavf: delete the iavf client interface
iavf: add a common function for undoing the interrupt scheme
iavf: use unregister_netdev
iavf: rely on netdev's own registered state
iavf: fix the waiting time for initial reset
iavf: in iavf_down, don't queue watchdog_task if comms failed
iavf: simplify mutex_trylock+sleep loops
iavf: fix comments about old bit locks
doc/netlink: Update schema to support cmd-cnt-name and cmd-max-name
tools: ynl: introduce option to process unknown attributes or types
ipvlan: properly track tx_errors
netdevsim: Block until all devices are released
nfp: using napi_build_skb() to replace build_skb()
net: dsa: microchip: ksz9477: Fix spelling mistake "Enery" -> "Energy"
net: dsa: microchip: Ensure Stable PME Pin State for Wake-on-LAN
net: dsa: microchip: Refactor switch shutdown routine for WoL preparation
...
|
|
Add the necessary structure to support custom private-data per
posix-clock user.
The previous implementation of posix-clock assumed all file open
instances need access to the same clock structure on private_data.
The need for individual data structures per file open instance has been
identified when developing support for multiple timestamp event queue
users for ptp_clock.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some userspace applications use timerfd_create() to request wakeups after
a long period of time. For example, a backup application may request a
wakeup once per week. This is perfectly fine as long as the system does
not try to suspend. However, if the system tries to suspend and the
system's RTC does not support the required alarm timeout, the suspend
operation will fail with an error such as
rtc_cmos 00:01: Alarms can be up to one day in the future
PM: dpm_run_callback(): platform_pm_suspend+0x0/0x4a returns -22
alarmtimer alarmtimer.4.auto: platform_pm_suspend+0x0/0x4a returned -22 after 117 usecs
PM: Device alarmtimer.4.auto failed to suspend: error -22
This results in a refusal to suspend the system, causing substantial
battery drain on affected systems.
To fix the problem, use the maximum alarm time offset as reported by RTC
drivers to set the maximum alarm time. While this may result in early
wakeups from suspend, it is still much better than not suspending at all.
Standardize system behavior if the requested alarm timeout is larger than
the alarm timeout supported by the rtc chip. Currently, in this situation,
the RTC driver will do one of the following:
- It may return an error.
- It may limit the alarm timeout to the maximum supported by the rtc chip.
- It may mask the timeout by the maximum alarm timeout supported by the RTC
chip (i.e. a requested timeout of 1 day + 1 minute may result in a 1
minute timeout).
With this in place, if the RTC driver reports the maximum alarm timeout
supported by the RTC chip, the system will always limit the alarm timeout
to the maximum supported by the RTC chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20230915152238.1144706-3-linux@roeck-us.net
|
|
Inspired by recent enhancements to comments in kernel/time/tick-sched.c,
go through the entire file and fix/unify its comments:
- Fix over a dozen typos, spelling mistakes & cases of bad grammar.
- Re-phrase sentences that I needed to read three times to understand.
[ I used the following arbitrary rule-of-thumb:
- if I had to read a comment twice, it was usually my fault,
- if I had to read it a third time, it was the comment's fault. ]
- Comma updates:
- Add commas where needed
- Remove commas where not needed
- In cases where a comma is optional, choose one variant and try to
standardize it over similar sentences in the file.
- Standardize on standalone 'NOHZ' spelling in free-flowing comments:
s/nohz/NOHZ
s/no idle tick/NOHZ
Still keep 'dynticks' as a popular synonym.
- Standardize on referring to variable names within free-flowing
comments with the "'var'" nomenclature, and function names as
"function_name()".
- Standardize on '64-bit' and '32-bit':
s/32bit/32-bit
s/64bit/64-bit
- Standardize on 'IRQ work':
s/irq work/IRQ work
- A few other tidyups I probably missed to list.
No change in functionality intended - other than one small change to
a syslog output string.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/ZRVCNeMcSQcXS36N@gmail.com
|
|
In lowres dynticks mode, just like in highres dynticks mode, when there
is no tick to program in the future, the tick eventually gets
deactivated either:
* From the idle loop if in idle mode.
* From the IRQ exit if in full dynticks mode.
Therefore there is no need to deactivate it from the tick itself. This
just just brings more overhead in the idle tick path for no reason.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20230912104406.312185-4-frederic@kernel.org
|
|
Some comments are obsolete enough to assume that IRQ exit restarts the
tick in idle or RCU is turned on at the same time as the tick, among
other details.
Update them and add more.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230912104406.312185-3-frederic@kernel.org
|
|
The current names of the tick handlers don't tell much about what different
between them. Use names that better reflect their role and resolution.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230912104406.312185-2-frederic@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix false positive 'softirq work is pending' messages on -rt kernels,
caused by a buggy factoring-out of existing code"
* tag 'timers-urgent-2023-09-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/rcu: Fix false positive "softirq work is pending" messages
|
