| Age | Commit message (Collapse) | Author |
|---|
|
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"A set of fixes for the scheduler:
- Fix handling of throttled parents in enqueue_task_fair() completely.
The recent fix overlooked a corner case where the first iteration
terminates due to an entity already being on the runqueue which
makes the list management incomplete and later triggers the
assertion which checks for completeness.
- Fix a similar problem in unthrottle_cfs_rq().
- Show the correct uclamp values in procfs which prints the effective
value twice instead of requested and effective"
* tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list
sched/debug: Fix requested task uclamp values shown in procfs
sched/fair: Fix enqueue_task_fair() warning some more
|
|
Currently, when considering the branches that may be taken for a jump
instruction if the register being compared is a pointer the verifier
assumes both branches may be taken. But, if the jump instruction
is comparing if a pointer is NULL we have this information in the
verifier encoded in the reg->type so we can do better in these cases.
Specifically, these two common cases can be handled.
* If the instruction is BPF_JEQ and we are comparing against a
zero value. This test is 'if ptr == 0 goto +X' then using the
type information in reg->type we can decide if the ptr is not
null. This allows us to avoid pushing both branches onto the
stack and instead only use the != 0 case. For example
PTR_TO_SOCK and PTR_TO_SOCK_OR_NULL encode the null pointer.
Note if the type is PTR_TO_SOCK_OR_NULL we can not learn anything.
And also if the value is non-zero we learn nothing because it
could be any arbitrary value a different pointer for example
* If the instruction is BPF_JNE and ware comparing against a zero
value then a similar analysis as above can be done. The test in
asm looks like 'if ptr != 0 goto +X'. Again using the type
information if the non null type is set (from above PTR_TO_SOCK)
we know the jump is taken.
In this patch we extend is_branch_taken() to consider this extra
information and to return only the branch that will be taken. This
resolves a verifier issue reported with C code like the following.
See progs/test_sk_lookup_kern.c in selftests.
sk = bpf_sk_lookup_tcp(skb, tuple, tuple_len, BPF_F_CURRENT_NETNS, 0);
bpf_printk("sk=%d\n", sk ? 1 : 0);
if (sk)
bpf_sk_release(sk);
return sk ? TC_ACT_OK : TC_ACT_UNSPEC;
In the above the bpf_printk() will resolve the pointer from
PTR_TO_SOCK_OR_NULL to PTR_TO_SOCK. Then the second test guarding
the release will cause the verifier to walk both paths resulting
in the an unreleased sock reference. See verifier/ref_tracking.c
in selftests for an assembly version of the above.
After the above additional logic is added the C code above passes
as expected.
Reported-by: Andrey Ignatov <rdna@fb.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159009164651.6313.380418298578070501.stgit@john-Precision-5820-Tower
|
|
The XSKMAP is partly implemented by net/xdp/xsk.c. Move xskmap.c from
kernel/bpf/ to net/xdp/, which is the logical place for AF_XDP related
code. Also, move AF_XDP struct definitions, and function declarations
only used by AF_XDP internals into net/xdp/xsk.h.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-3-bjorn.topel@gmail.com
|
|
As discussed in [0], it's dangerous to allow mapping BPF map, that's meant to
be frozen and is read-only on BPF program side, because that allows user-space
to actually store a writable view to the page even after it is frozen. This is
exacerbated by BPF verifier making a strong assumption that contents of such
frozen map will remain unchanged. To prevent this, disallow mapping
BPF_F_RDONLY_PROG mmap()'able BPF maps as writable, ever.
[0] https://lore.kernel.org/bpf/CAEf4BzYGWYhXdp6BJ7_=9OQPJxQpgug080MMjdSB72i9R+5c6g@mail.gmail.com/
Fixes: fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/bpf/20200519053824.1089415-1-andriin@fb.com
|
|
Although not exactly identical, unthrottle_cfs_rq() and enqueue_task_fair()
are quite close and follow the same sequence for enqueuing an entity in the
cfs hierarchy. Modify unthrottle_cfs_rq() to use the same pattern as
enqueue_task_fair(). This fixes a problem already faced with the latter and
add an optimization in the last for_each_sched_entity loop.
Fixes: fe61468b2cb (sched/fair: Fix enqueue_task_fair warning)
Reported-by Tao Zhou <zohooouoto@zoho.com.cn>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Phil Auld <pauld@redhat.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/20200513135528.4742-1-vincent.guittot@linaro.org
|
|
The intention of commit 96e74ebf8d59 ("sched/debug: Add task uclamp
values to SCHED_DEBUG procfs") was to print requested and effective
task uclamp values. The requested values printed are read from p->uclamp,
which holds the last effective values. Fix this by printing the values
from p->uclamp_req.
Fixes: 96e74ebf8d59 ("sched/debug: Add task uclamp values to SCHED_DEBUG procfs")
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lkml.kernel.org/r/1589115401-26391-1-git-send-email-pkondeti@codeaurora.org
|
|
sched/fair: Fix enqueue_task_fair warning some more
The recent patch, fe61468b2cb (sched/fair: Fix enqueue_task_fair warning)
did not fully resolve the issues with the rq->tmp_alone_branch !=
&rq->leaf_cfs_rq_list warning in enqueue_task_fair. There is a case where
the first for_each_sched_entity loop exits due to on_rq, having incompletely
updated the list. In this case the second for_each_sched_entity loop can
further modify se. The later code to fix up the list management fails to do
what is needed because se does not point to the sched_entity which broke out
of the first loop. The list is not fixed up because the throttled parent was
already added back to the list by a task enqueue in a parallel child hierarchy.
Address this by calling list_add_leaf_cfs_rq if there are throttled parents
while doing the second for_each_sched_entity loop.
Fixes: fe61468b2cb ("sched/fair: Fix enqueue_task_fair warning")
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/20200512135222.GC2201@lorien.usersys.redhat.com
|
|
As stated in 983695fa6765 ("bpf: fix unconnected udp hooks"), the objective
for the existing cgroup connect/sendmsg/recvmsg/bind BPF hooks is to be
transparent to applications. In Cilium we make use of these hooks [0] in
order to enable E-W load balancing for existing Kubernetes service types
for all Cilium managed nodes in the cluster. Those backends can be local
or remote. The main advantage of this approach is that it operates as close
as possible to the socket, and therefore allows to avoid packet-based NAT
given in connect/sendmsg/recvmsg hooks we only need to xlate sock addresses.
This also allows to expose NodePort services on loopback addresses in the
host namespace, for example. As another advantage, this also efficiently
blocks bind requests for applications in the host namespace for exposed
ports. However, one missing item is that we also need to perform reverse
xlation for inet{,6}_getname() hooks such that we can return the service
IP/port tuple back to the application instead of the remote peer address.
The vast majority of applications does not bother about getpeername(), but
in a few occasions we've seen breakage when validating the peer's address
since it returns unexpectedly the backend tuple instead of the service one.
Therefore, this trivial patch allows to customise and adds a getpeername()
as well as getsockname() BPF cgroup hook for both IPv4 and IPv6 in order
to address this situation.
Simple example:
# ./cilium/cilium service list
ID Frontend Service Type Backend
1 1.2.3.4:80 ClusterIP 1 => 10.0.0.10:80
Before; curl's verbose output example, no getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (10.0.0.10) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
After; with getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (1.2.3.4) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
Originally, I had both under a BPF_CGROUP_INET{4,6}_GETNAME type and exposed
peer to the context similar as in inet{,6}_getname() fashion, but API-wise
this is suboptimal as it always enforces programs having to test for ctx->peer
which can easily be missed, hence BPF_CGROUP_INET{4,6}_GET{PEER,SOCK}NAME split.
Similarly, the checked return code is on tnum_range(1, 1), but if a use case
comes up in future, it can easily be changed to return an error code instead.
Helper and ctx member access is the same as with connect/sendmsg/etc hooks.
[0] https://github.com/cilium/cilium/blob/master/bpf/bpf_sock.c
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/61a479d759b2482ae3efb45546490bacd796a220.1589841594.git.daniel@iogearbox.net
|
|
As per 15d83c4d7cef ("bpf: Allow loading of a bpf_iter program") we only
allow a range of [0,1] for return codes. Therefore BPF_TRACE_ITER relies
on the default tnum_range(0, 1) which is set in range var. On recent merge
of net into net-next commit e92888c72fbd ("bpf: Enforce returning 0 for
fentry/fexit progs") got pulled in and caused a merge conflict with the
changes from 15d83c4d7cef. The resolution had a snall hiccup in that it
removed the [0,1] range restriction again so that BPF_TRACE_ITER would
have no enforcement. Fix it by adding it back.
Fixes: da07f52d3caf ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix sk_psock reference count leak on receive, from Xiyu Yang.
2) CONFIG_HNS should be invisible, from Geert Uytterhoeven.
3) Don't allow locking route MTUs in ipv6, RFCs actually forbid this,
from Maciej Żenczykowski.
4) ipv4 route redirect backoff wasn't actually enforced, from Paolo
Abeni.
5) Fix netprio cgroup v2 leak, from Zefan Li.
6) Fix infinite loop on rmmod in conntrack, from Florian Westphal.
7) Fix tcp SO_RCVLOWAT hangs, from Eric Dumazet.
8) Various bpf probe handling fixes, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
selftests: mptcp: pm: rm the right tmp file
dpaa2-eth: properly handle buffer size restrictions
bpf: Restrict bpf_trace_printk()'s %s usage and add %pks, %pus specifier
bpf: Add bpf_probe_read_{user, kernel}_str() to do_refine_retval_range
bpf: Restrict bpf_probe_read{, str}() only to archs where they work
MAINTAINERS: Mark networking drivers as Maintained.
ipmr: Add lockdep expression to ipmr_for_each_table macro
ipmr: Fix RCU list debugging warning
drivers: net: hamradio: Fix suspicious RCU usage warning in bpqether.c
net: phy: broadcom: fix BCM54XX_SHD_SCR3_TRDDAPD value for BCM54810
tcp: fix error recovery in tcp_zerocopy_receive()
MAINTAINERS: Add Jakub to networking drivers.
MAINTAINERS: another add of Karsten Graul for S390 networking
drivers: ipa: fix typos for ipa_smp2p structure doc
pppoe: only process PADT targeted at local interfaces
selftests/bpf: Enforce returning 0 for fentry/fexit programs
bpf: Enforce returning 0 for fentry/fexit progs
net: stmmac: fix num_por initialization
security: Fix the default value of secid_to_secctx hook
libbpf: Fix register naming in PT_REGS s390 macros
...
|
|
Implement permissions as stated in uapi/linux/capability.h
In order to do that the verifier allow_ptr_leaks flag is split
into four flags and they are set as:
env->allow_ptr_leaks = bpf_allow_ptr_leaks();
env->bypass_spec_v1 = bpf_bypass_spec_v1();
env->bypass_spec_v4 = bpf_bypass_spec_v4();
env->bpf_capable = bpf_capable();
The first three currently equivalent to perfmon_capable(), since leaking kernel
pointers and reading kernel memory via side channel attacks is roughly
equivalent to reading kernel memory with cap_perfmon.
'bpf_capable' enables bounded loops, precision tracking, bpf to bpf calls and
other verifier features. 'allow_ptr_leaks' enable ptr leaks, ptr conversions,
subtraction of pointers. 'bypass_spec_v1' disables speculative analysis in the
verifier, run time mitigations in bpf array, and enables indirect variable
access in bpf programs. 'bypass_spec_v4' disables emission of sanitation code
by the verifier.
That means that the networking BPF program loaded with CAP_BPF + CAP_NET_ADMIN
will have speculative checks done by the verifier and other spectre mitigation
applied. Such networking BPF program will not be able to leak kernel pointers
and will not be able to access arbitrary kernel memory.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200513230355.7858-3-alexei.starovoitov@gmail.com
|
|
Usage of plain %s conversion specifier in bpf_trace_printk() suffers from the
very same issue as bpf_probe_read{,str}() helpers, that is, it is broken on
archs with overlapping address ranges.
While the helpers have been addressed through work in 6ae08ae3dea2 ("bpf: Add
probe_read_{user, kernel} and probe_read_{user, kernel}_str helpers"), we need
an option for bpf_trace_printk() as well to fix it.
Similarly as with the helpers, force users to make an explicit choice by adding
%pks and %pus specifier to bpf_trace_printk() which will then pick the corresponding
strncpy_from_unsafe*() variant to perform the access under KERNEL_DS or USER_DS.
The %pk* (kernel specifier) and %pu* (user specifier) can later also be extended
for other objects aside strings that are probed and printed under tracing, and
reused out of other facilities like bpf_seq_printf() or BTF based type printing.
Existing behavior of %s for current users is still kept working for archs where it
is not broken and therefore gated through CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE.
For archs not having this property we fall-back to pick probing under KERNEL_DS as
a sensible default.
Fixes: 8d3b7dce8622 ("bpf: add support for %s specifier to bpf_trace_printk()")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Link: https://lore.kernel.org/bpf/20200515101118.6508-4-daniel@iogearbox.net
|
|
Given bpf_probe_read{,str}() BPF helpers are now only available under
CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE, we need to add the drop-in
replacements of bpf_probe_read_{kernel,user}_str() to do_refine_retval_range()
as well to avoid hitting the same issue as in 849fa50662fbc ("bpf/verifier:
refine retval R0 state for bpf_get_stack helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200515101118.6508-3-daniel@iogearbox.net
|
|
Given the legacy bpf_probe_read{,str}() BPF helpers are broken on archs
with overlapping address ranges, we should really take the next step to
disable them from BPF use there.
To generally fix the situation, we've recently added new helper variants
bpf_probe_read_{user,kernel}() and bpf_probe_read_{user,kernel}_str().
For details on them, see 6ae08ae3dea2 ("bpf: Add probe_read_{user, kernel}
and probe_read_{user,kernel}_str helpers").
Given bpf_probe_read{,str}() have been around for ~5 years by now, there
are plenty of users at least on x86 still relying on them today, so we
cannot remove them entirely w/o breaking the BPF tracing ecosystem.
However, their use should be restricted to archs with non-overlapping
address ranges where they are working in their current form. Therefore,
move this behind a CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE and
have x86, arm64, arm select it (other archs supporting it can follow-up
on it as well).
For the remaining archs, they can workaround easily by relying on the
feature probe from bpftool which spills out defines that can be used out
of BPF C code to implement the drop-in replacement for old/new kernels
via: bpftool feature probe macro
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/bpf/20200515101118.6508-2-daniel@iogearbox.net
|
|
Knowing the memory size backing the packet/xdp_frame data area, and
knowing it already have reserved room for skb_shared_info, simplifies
using build_skb significantly.
With this change we no-longer lie about the SKB truesize, but more
importantly a significant larger skb_tailroom is now provided, e.g. when
drivers uses a full PAGE_SIZE. This extra tailroom (in linear area) can be
used by the network stack when coalescing SKBs (e.g. in skb_try_coalesce,
see TCP cases where tcp_queue_rcv() can 'eat' skb).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945337822.97035.13557959180460986059.stgit@firesoul
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-14
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Merged tag 'perf-for-bpf-2020-05-06' from tip tree that includes CAP_PERFMON.
2) support for narrow loads in bpf_sock_addr progs and additional
helpers in cg-skb progs, from Andrey.
3) bpf benchmark runner, from Andrii.
4) arm and riscv JIT optimizations, from Luke.
5) bpf iterator infrastructure, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
task_seq_get_next might stop prematurely if get_pid_task() fails to get
task_struct. Failure to do so doesn't mean that there are no more tasks with
higher pids. Procfs's iteration algorithm (see next_tgid in fs/proc/base.c)
does a retry in such case. After this fix, instead of stopping prematurely
after about 300 tasks on my server, bpf_iter program now returns >4000, which
sounds much closer to reality.
Fixes: eaaacd23910f ("bpf: Add task and task/file iterator targets")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200514055137.1564581-1-andriin@fb.com
|
|
Currently, tracing/fentry and tracing/fexit prog
return values are not enforced. In trampoline codes,
the fentry/fexit prog return values are ignored.
Let us enforce it to be 0 to avoid confusion and
allows potential future extension.
This patch also explicitly added return value
checking for tracing/raw_tp, tracing/fmod_ret,
and freplace programs such that these program
return values can be anything. The purpose are
two folds:
1. to make it explicit about return value expectations
for these programs in verifier.
2. for tracing prog_type, if a future attach type
is added, the default is -ENOTSUPP which will
enforce to specify return value ranges explicitly.
Fixes: fec56f5890d9 ("bpf: Introduce BPF trampoline")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200514053206.1298415-1-yhs@fb.com
|
|
mmap() subsystem allows user-space application to memory-map region with
initial page offset. This wasn't taken into account in initial implementation
of BPF array memory-mapping. This would result in wrong pages, not taking into
account requested page shift, being memory-mmaped into user-space. This patch
fixes this gap and adds a test for such scenario.
Fixes: fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200512235925.3817805-1-andriin@fb.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread fix from Christian Brauner:
"This contains a single fix for all exported legacy fork helpers to
block accidental access to clone3() features in the upper 32 bits of
their respective flags arguments.
I got Cced on a glibc issue where someone reported consistent failures
for the legacy clone() syscall on ppc64le when sign extension was
performed (since the clone() syscall in glibc exposes the flags
argument as an int whereas the kernel uses unsigned long).
The legacy clone() syscall is odd in a bunch of ways and here two
things interact:
- First, legacy clone's flag argument is word-size dependent, i.e.
it's an unsigned long whereas most system calls with flag arguments
use int or unsigned int.
- Second, legacy clone() ignores unknown and deprecated flags.
The two of them taken together means that users on 64bit systems can
pass garbage for the upper 32bit of the clone() syscall since forever
and things would just work fine.
The following program compiled on a 64bit kernel prior to v5.7-rc1
will succeed and will fail post v5.7-rc1 with EBADF:
int main(int argc, char *argv[])
{
pid_t pid;
/* Note that legacy clone() has different argument ordering on
* different architectures so this won't work everywhere.
*
* Only set the upper 32 bits.
*/
pid = syscall(__NR_clone, 0xffffffff00000000 | SIGCHLD,
NULL, NULL, NULL, NULL);
if (pid < 0)
exit(EXIT_FAILURE);
if (pid == 0)
exit(EXIT_SUCCESS);
if (wait(NULL) != pid)
exit(EXIT_FAILURE);
exit(EXIT_SUCCESS);
}
Since legacy clone() couldn't be extended this was not a problem so
far and nobody really noticed or cared since nothing in the kernel
ever bothered to look at the upper 32 bits.
But once we introduced clone3() and expanded the flag argument in
struct clone_args to 64 bit we opened this can of worms. With the
first flag-based extension to clone3() making use of the upper 32 bits
of the flag argument we've effectively made it possible for the legacy
clone() syscall to reach clone3() only flags on accident. The sign
extension scenario is just the odd corner-case that we needed to
figure this out.
The reason we just realized this now and not already when we
introduced CLONE_CLEAR_SIGHAND was that CLONE_INTO_CGROUP assumes that
a valid cgroup file descriptor has been given - whereas
CLONE_CLEAR_SIGHAND doesn't need to verify anything. It just silently
resets the signal handlers to SIG_DFL.
So the sign extension (or the user accidently passing garbage for the
upper 32 bits) caused the CLONE_INTO_CGROUP bit to be raised and the
kernel to error out when it didn't find a valid cgroup file
descriptor.
Note, I'm also capping kernel_thread()'s flag argument mainly because
none of the new features make sense for kernel_thread() and we
shouldn't risk them being accidently activated however unlikely. If we
wanted to, we could even make kernel_thread() yell when an unknown
flag has been set which it doesn't do right now. But it's not worth
risking this in a bugfix imho"
* tag 'for-linus-2020-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: prevent accidental access to clone3 features
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull more tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a crash when having function tracing and function stack tracing
on the command line.
The ftrace trampolines are created as executable and read only. But
the stack tracer tries to modify them with text_poke() which
expects all kernel text to still be writable at boot. Keep the
trampolines writable at boot, and convert them to read-only with
the rest of the kernel.
- A selftest was triggering in the ring buffer iterator code, that is
no longer valid with the update of keeping the ring buffer writable
while a iterator is reading.
Just bail after three failed attempts to get an event and remove
the warning and disabling of the ring buffer.
- While modifying the ring buffer code, decided to remove all the
unnecessary BUG() calls"
* tag 'trace-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Remove all BUG() calls
ring-buffer: Don't deactivate the ring buffer on failed iterator reads
x86/ftrace: Have ftrace trampolines turn read-only at the end of system boot up
|
|
There's a lot of checks to make sure the ring buffer is working, and if an
anomaly is detected, it safely shuts itself down. But there's a few cases
that it will call BUG(), which defeats the point of being safe (it crashes
the kernel when an anomaly is found!). There's no reason for them. Switch
them all to either WARN_ON_ONCE() (when no ring buffer descriptor is present),
or to RB_WARN_ON() (when a ring buffer descriptor is present).
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
If the function tracer is running and the trace file is read (which uses the
ring buffer iterator), the iterator can get in sync with the writes, and
caues it to fail to find a page with content it can read three times. This
causes a warning and deactivation of the ring buffer code.
Looking at the other cases of failure to get an event, it appears that
there's a chance that the writer could cause them too. Since the iterator is
a "best effort" to read the ring buffer if there's an active writer (the
consumer reader is made for this case "see trace_pipe"), if it fails to get
an event after three tries, simply give up and return NULL. Don't warn, nor
disable the ring buffer on this failure.
Link: https://lore.kernel.org/r/20200429090508.GG5770@shao2-debian
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ff84c50cfb4b ("ring-buffer: Do not die if rb_iter_peek() fails more than thrice")
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Commit b121b341e598 ("bpf: Add PTR_TO_BTF_ID_OR_NULL
support") adds a field btf_id_or_null_non0_off to
bpf_prog->aux structure to indicate that the
first ctx argument is PTR_TO_BTF_ID reg_type and
all others are PTR_TO_BTF_ID_OR_NULL.
This approach does not really scale if we have
other different reg types in the future, e.g.,
a pointer to a buffer.
This patch enables bpf_iter targets registering ctx argument
reg types which may be different from the default one.
For example, for pointers to structures, the default reg_type
is PTR_TO_BTF_ID for tracing program. The target can register
a particular pointer type as PTR_TO_BTF_ID_OR_NULL which can
be used by the verifier to enforce accesses.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180221.2949882-1-yhs@fb.com
|
|
Change func bpf_iter_unreg_target() parameter from target
name to target reg_info, similar to bpf_iter_reg_target().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180220.2949737-1-yhs@fb.com
|
|
Currently bpf_iter_reg_target takes parameters from target
and allocates memory to save them. This is really not
necessary, esp. in the future we may grow information
passed from targets to bpf_iter manager.
The patch refactors the code so target reg_info
becomes static and bpf_iter manager can just take
a reference to it.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200513180219.2949605-1-yhs@fb.com
|
|
Add a short comment in bpf_iter_run_prog() function to
explain how bpf_prog return value is converted to
seq_ops->show() return value:
bpf_prog return seq_ops()->show() return
0 0
1 -EAGAIN
When show() return value is -EAGAIN, the current
bpf_seq_read() will end. If the current seq_file buffer
is empty, -EAGAIN will return to user space. Otherwise,
the buffer will be copied to user space.
In both cases, the next bpf_seq_read() call will
try to show the same object which returned -EAGAIN
previously.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180218.2949517-1-yhs@fb.com
|
|
Booting one of my machines, it triggered the following crash:
Kernel/User page tables isolation: enabled
ftrace: allocating 36577 entries in 143 pages
Starting tracer 'function'
BUG: unable to handle page fault for address: ffffffffa000005c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
PGD 2014067 P4D 2014067 PUD 2015063 PMD 7b253067 PTE 7b252061
Oops: 0003 [#1] PREEMPT SMP PTI
CPU: 0 PID: 0 Comm: swapper Not tainted 5.4.0-test+ #24
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
RIP: 0010:text_poke_early+0x4a/0x58
Code: 34 24 48 89 54 24 08 e8 bf 72 0b 00 48 8b 34 24 48 8b 4c 24 08 84 c0 74 0b 48 89 df f3 a4 48 83 c4 10 5b c3 9c 58 fa 48 89 df <f3> a4 50 9d 48 83 c4 10 5b e9 d6 f9 ff ff
0 41 57 49
RSP: 0000:ffffffff82003d38 EFLAGS: 00010046
RAX: 0000000000000046 RBX: ffffffffa000005c RCX: 0000000000000005
RDX: 0000000000000005 RSI: ffffffff825b9a90 RDI: ffffffffa000005c
RBP: ffffffffa000005c R08: 0000000000000000 R09: ffffffff8206e6e0
R10: ffff88807b01f4c0 R11: ffffffff8176c106 R12: ffffffff8206e6e0
R13: ffffffff824f2440 R14: 0000000000000000 R15: ffffffff8206eac0
FS: 0000000000000000(0000) GS:ffff88807d400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa000005c CR3: 0000000002012000 CR4: 00000000000006b0
Call Trace:
text_poke_bp+0x27/0x64
? mutex_lock+0x36/0x5d
arch_ftrace_update_trampoline+0x287/0x2d5
? ftrace_replace_code+0x14b/0x160
? ftrace_update_ftrace_func+0x65/0x6c
__register_ftrace_function+0x6d/0x81
ftrace_startup+0x23/0xc1
register_ftrace_function+0x20/0x37
func_set_flag+0x59/0x77
__set_tracer_option.isra.19+0x20/0x3e
trace_set_options+0xd6/0x13e
apply_trace_boot_options+0x44/0x6d
register_tracer+0x19e/0x1ac
early_trace_init+0x21b/0x2c9
start_kernel+0x241/0x518
? load_ucode_intel_bsp+0x21/0x52
secondary_startup_64+0xa4/0xb0
I was able to trigger it on other machines, when I added to the kernel
command line of both "ftrace=function" and "trace_options=func_stack_trace".
The cause is the "ftrace=function" would register the function tracer
and create a trampoline, and it will set it as executable and
read-only. Then the "trace_options=func_stack_trace" would then update
the same trampoline to include the stack tracer version of the function
tracer. But since the trampoline already exists, it updates it with
text_poke_bp(). The problem is that text_poke_bp() called while
system_state == SYSTEM_BOOTING, it will simply do a memcpy() and not
the page mapping, as it would think that the text is still read-write.
But in this case it is not, and we take a fault and crash.
Instead, lets keep the ftrace trampolines read-write during boot up,
and then when the kernel executable text is set to read-only, the
ftrace trampolines get set to read-only as well.
Link: https://lkml.kernel.org/r/20200430202147.4dc6e2de@oasis.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
Fixes: 768ae4406a5c ("x86/ftrace: Use text_poke()")
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Fixes to previous fixes.
Unfortunately, the last set of fixes introduced some minor bugs:
- The bootconfig apply_xbc() leak fix caused the application to
return a positive number on success, when it should have returned
zero.
- The preempt_irq_delay_thread fix to make the creation code wait for
the kthread to finish to prevent it from executing after module
unload, can now cause the kthread to exit before it even executes
(preventing it to run its tests).
- The fix to the bootconfig that fixed the initrd to remove the
bootconfig from causing the kernel to panic, now prints a warning
that the bootconfig is not found, even when bootconfig is not on
the command line"
* tag 'trace-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Fix to prevent warning message if no bootconfig option
tracing: Wait for preempt irq delay thread to execute
tools/bootconfig: Fix apply_xbc() to return zero on success
|
|
A bug report was posted that running the preempt irq delay module on a slow
machine, and removing it quickly could lead to the thread created by the
modlue to execute after the module is removed, and this could cause the
kernel to crash. The fix for this was to call kthread_stop() after creating
the thread to make sure it finishes before allowing the module to be
removed.
Now this caused the opposite problem on fast machines. What now happens is
the kthread_stop() can cause the kthread never to execute and the test never
to run. To fix this, add a completion and wait for the kthread to execute,
then wait for it to end.
This issue caused the ftracetest selftests to fail on the preemptirq tests.
Link: https://lore.kernel.org/r/20200510114210.15d9e4af@oasis.local.home
Cc: stable@vger.kernel.org
Fixes: d16a8c31077e ("tracing: Wait for preempt irq delay thread to finish")
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200507185057.GA13981@embeddedor
|
|
In /proc/net/ipv6_route, we have
struct fib6_info {
struct fib6_table *fib6_table;
...
struct fib6_nh fib6_nh[0];
}
struct fib6_nh {
struct fib_nh_common nh_common;
struct rt6_info **rt6i_pcpu;
struct rt6_exception_bucket *rt6i_exception_bucket;
};
struct fib_nh_common {
...
u8 nhc_gw_family;
...
}
The access:
struct fib6_nh *fib6_nh = &rt->fib6_nh;
... fib6_nh->nh_common.nhc_gw_family ...
This patch ensures such an access is handled properly.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175916.2476853-1-yhs@fb.com
|
|
This specifically to handle the case like below:
// ptr below is a socket ptr identified by PTR_TO_BTF_ID
u64 param[2] = { ptr, val };
bpf_seq_printf(seq, fmt, sizeof(fmt), param, sizeof(param));
In this case, the 16 bytes stack for "param" contains:
8 bytes for ptr with spilled PTR_TO_BTF_ID
8 bytes for val as STACK_MISC
The current verifier will complain the ptr should not be visible
to the helper.
...
16: (7b) *(u64 *)(r10 -64) = r2
18: (7b) *(u64 *)(r10 -56) = r1
19: (bf) r4 = r10
;
20: (07) r4 += -64
; BPF_SEQ_PRINTF(seq, fmt1, (long)s, s->sk_protocol);
21: (bf) r1 = r6
22: (18) r2 = 0xffffa8d00018605a
24: (b4) w3 = 10
25: (b4) w5 = 16
26: (85) call bpf_seq_printf#125
R0=inv(id=0) R1_w=ptr_seq_file(id=0,off=0,imm=0)
R2_w=map_value(id=0,off=90,ks=4,vs=144,imm=0) R3_w=inv10
R4_w=fp-64 R5_w=inv16 R6=ptr_seq_file(id=0,off=0,imm=0)
R7=ptr_netlink_sock(id=0,off=0,imm=0) R10=fp0 fp-56_w=mmmmmmmm
fp-64_w=ptr_
last_idx 26 first_idx 13
regs=8 stack=0 before 25: (b4) w5 = 16
regs=8 stack=0 before 24: (b4) w3 = 10
invalid indirect read from stack off -64+0 size 16
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175915.2476783-1-yhs@fb.com
|
|
Two helpers bpf_seq_printf and bpf_seq_write, are added for
writing data to the seq_file buffer.
bpf_seq_printf supports common format string flag/width/type
fields so at least I can get identical results for
netlink and ipv6_route targets.
For bpf_seq_printf and bpf_seq_write, return value -EOVERFLOW
specifically indicates a write failure due to overflow, which
means the object will be repeated in the next bpf invocation
if object collection stays the same. Note that if the object
collection is changed, depending how collection traversal is
done, even if the object still in the collection, it may not
be visited.
For bpf_seq_printf, format %s, %p{i,I}{4,6} needs to
read kernel memory. Reading kernel memory may fail in
the following two cases:
- invalid kernel address, or
- valid kernel address but requiring a major fault
If reading kernel memory failed, the %s string will be
an empty string and %p{i,I}{4,6} will be all 0.
Not returning error to bpf program is consistent with
what bpf_trace_printk() does for now.
bpf_seq_printf may return -EBUSY meaning that internal percpu
buffer for memory copy of strings or other pointees is
not available. Bpf program can return 1 to indicate it
wants the same object to be repeated. Right now, this should not
happen on no-RT kernels since migrate_disable(), which guards
bpf prog call, calls preempt_disable().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175914.2476661-1-yhs@fb.com
|
|
Add bpf_reg_type PTR_TO_BTF_ID_OR_NULL support.
For tracing/iter program, the bpf program context
definition, e.g., for previous bpf_map target, looks like
struct bpf_iter__bpf_map {
struct bpf_iter_meta *meta;
struct bpf_map *map;
};
The kernel guarantees that meta is not NULL, but
map pointer maybe NULL. The NULL map indicates that all
objects have been traversed, so bpf program can take
proper action, e.g., do final aggregation and/or send
final report to user space.
Add btf_id_or_null_non0_off to prog->aux structure, to
indicate that if the context access offset is not 0,
set to PTR_TO_BTF_ID_OR_NULL instead of PTR_TO_BTF_ID.
This bit is set for tracing/iter program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175912.2476576-1-yhs@fb.com
|
|
Only the tasks belonging to "current" pid namespace
are enumerated.
For task/file target, the bpf program will have access to
struct task_struct *task
u32 fd
struct file *file
where fd/file is an open file for the task.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175911.2476407-1-yhs@fb.com
|
|
Implement seq_file operations to traverse all bpf_maps.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175909.2476096-1-yhs@fb.com
|
|
Macro DEFINE_BPF_ITER_FUNC is implemented so target
can define an init function to capture the BTF type
which represents the target.
The bpf_iter_meta is a structure holding meta data, common
to all targets in the bpf program.
Additional marker functions are called before or after
bpf_seq_read() show()/next()/stop() callback functions
to help calculate precise seq_num and whether call bpf_prog
inside stop().
Two functions, bpf_iter_get_info() and bpf_iter_run_prog(),
are implemented so target can get needed information from
bpf_iter infrastructure and can run the program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175907.2475956-1-yhs@fb.com
|
|
To produce a file bpf iterator, the fd must be
corresponding to a link_fd assocciated with a
trace/iter program. When the pinned file is
opened, a seq_file will be generated.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175906.2475893-1-yhs@fb.com
|
|
A new bpf command BPF_ITER_CREATE is added.
The anonymous bpf iterator is seq_file based.
The seq_file private data are referenced by targets.
The bpf_iter infrastructure allocated additional space
at seq_file->private before the space used by targets
to store some meta data, e.g.,
prog: prog to run
session_id: an unique id for each opened seq_file
seq_num: how many times bpf programs are queried in this session
done_stop: an internal state to decide whether bpf program
should be called in seq_ops->stop() or not
The seq_num will start from 0 for valid objects.
The bpf program may see the same seq_num more than once if
- seq_file buffer overflow happens and the same object
is retried by bpf_seq_read(), or
- the bpf program explicitly requests a retry of the
same object
Since module is not supported for bpf_iter, all target
registeration happens at __init time, so there is no
need to change bpf_iter_unreg_target() as it is used
mostly in error path of the init function at which time
no bpf iterators have been created yet.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175905.2475770-1-yhs@fb.com
|
|
bpf iterator uses seq_file to provide a lossless
way to transfer data to user space. But we want to call
bpf program after all objects have been traversed, and
bpf program may write additional data to the
seq_file buffer. The current seq_read() does not work
for this use case.
Besides allowing stop() function to write to the buffer,
the bpf_seq_read() also fixed the buffer size to one page.
If any single call of show() or stop() will emit data
more than one page to cause overflow, -E2BIG error code
will be returned to user space.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175904.2475468-1-yhs@fb.com
|
|
Added BPF_LINK_UPDATE support for tracing/iter programs.
This way, a file based bpf iterator, which holds a reference
to the link, can have its bpf program updated without
creating new files.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175902.2475262-1-yhs@fb.com
|
|
Given a bpf program, the step to create an anonymous bpf iterator is:
- create a bpf_iter_link, which combines bpf program and the target.
In the future, there could be more information recorded in the link.
A link_fd will be returned to the user space.
- create an anonymous bpf iterator with the given link_fd.
The bpf_iter_link can be pinned to bpffs mount file system to
create a file based bpf iterator as well.
The benefit to use of bpf_iter_link:
- using bpf link simplifies design and implementation as bpf link
is used for other tracing bpf programs.
- for file based bpf iterator, bpf_iter_link provides a standard
way to replace underlying bpf programs.
- for both anonymous and free based iterators, bpf link query
capability can be leveraged.
The patch added support of tracing/iter programs for BPF_LINK_CREATE.
A new link type BPF_LINK_TYPE_ITER is added to facilitate link
querying. Currently, only prog_id is needed, so there is no
additional in-kernel show_fdinfo() and fill_link_info() hook
is needed for BPF_LINK_TYPE_ITER link.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175901.2475084-1-yhs@fb.com
|
|
A bpf_iter program is a tracing program with attach type
BPF_TRACE_ITER. The load attribute
attach_btf_id
is used by the verifier against a particular kernel function,
which represents a target, e.g., __bpf_iter__bpf_map
for target bpf_map which is implemented later.
The program return value must be 0 or 1 for now.
0 : successful, except potential seq_file buffer overflow
which is handled by seq_file reader.
1 : request to restart the same object
In the future, other return values may be used for filtering or
teminating the iterator.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175900.2474947-1-yhs@fb.com
|
|
The target can call bpf_iter_reg_target() to register itself.
The needed information:
target: target name
seq_ops: the seq_file operations for the target
init_seq_private target callback to initialize seq_priv during file open
fini_seq_private target callback to clean up seq_priv during file release
seq_priv_size: the private_data size needed by the seq_file
operations
The target name represents a target which provides a seq_ops
for iterating objects.
The target can provide two callback functions, init_seq_private
and fini_seq_private, called during file open/release time.
For example, /proc/net/{tcp6, ipv6_route, netlink, ...}, net
name space needs to be setup properly during file open and
released properly during file release.
Function bpf_iter_unreg_target() is also implemented to unregister
a particular target.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175859.2474669-1-yhs@fb.com
|
|
We have some rather random rules about when we accept the
"maybe-initialized" warnings, and when we don't.
For example, we consider it unreliable for gcc versions < 4.9, but also
if -O3 is enabled, or if optimizing for size. And then various kernel
config options disabled it, because they know that they trigger that
warning by confusing gcc sufficiently (ie PROFILE_ALL_BRANCHES).
And now gcc-10 seems to be introducing a lot of those warnings too, so
it falls under the same heading as 4.9 did.
At the same time, we have a very straightforward way to _enable_ that
warning when wanted: use "W=2" to enable more warnings.
So stop playing these ad-hoc games, and just disable that warning by
default, with the known and straight-forward "if you want to work on the
extra compiler warnings, use W=123".
Would it be great to have code that is always so obvious that it never
confuses the compiler whether a variable is used initialized or not?
Yes, it would. In a perfect world, the compilers would be smarter, and
our source code would be simpler.
That's currently not the world we live in, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a UMH process created by fork_usermode_blob() fails to execute,
a pair of struct file allocated by umh_pipe_setup() will leak.
Under normal conditions, the caller (like bpfilter) needs to manage the
lifetime of the UMH and its two pipes. But when fork_usermode_blob()
fails, the caller doesn't really have a way to know what needs to be
done. It seems better to do the cleanup ourselves in this case.
Fixes: 449325b52b7a ("umh: introduce fork_usermode_blob() helper")
Signed-off-by: Vincent Minet <v.minet@criteo.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-05-09
The following pull-request contains BPF updates for your *net* tree.
We've added 4 non-merge commits during the last 9 day(s) which contain
a total of 4 files changed, 11 insertions(+), 6 deletions(-).
The main changes are:
1) Fix msg_pop_data() helper incorrectly setting an sge length in some
cases as well as fixing bpf_tcp_ingress() wrongly accounting bytes
in sg.size, from John Fastabend.
2) Fix to return an -EFAULT error when copy_to_user() of the value
fails in map_lookup_and_delete_elem(), from Wei Yongjun.
3) Fix sk_psock refcnt leak in tcp_bpf_recvmsg(), from Xiyu Yang.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
