summaryrefslogtreecommitdiff
path: root/mm/mremap.c
AgeCommit message (Collapse)Author
2018-06-15mremap: remove LATENCY_LIMIT from mremap to reduce the number of TLB shootdownsMel Gorman
Commit 5d1904204c99 ("mremap: fix race between mremap() and page cleanning") fixed races between mremap and other operations for both file-backed and anonymous mappings. The file-backed was the most critical as it allowed the possibility that data could be changed on a physical page after page_mkclean returned which could trigger data loss or data integrity issues. A customer reported that the cost of the TLBs for anonymous regressions was excessive and resulting in a 30-50% drop in performance overall since this commit on a microbenchmark. Unfortunately I neither have access to the test-case nor can I describe what it does other than saying that mremap operations dominate heavily. This patch removes the LATENCY_LIMIT to handle TLB flushes on a PMD boundary instead of every 64 pages to reduce the number of TLB shootdowns by a factor of 8 in the ideal case. LATENCY_LIMIT was almost certainly used originally to limit the PTL hold times but the latency savings are likely offset by the cost of IPIs in many cases. This patch is not reported to completely restore performance but gets it within an acceptable percentage. The given metric here is simply described as "higher is better". Baseline that was known good 002: Metric: 91.05 004: Metric: 109.45 008: Metric: 73.08 016: Metric: 58.14 032: Metric: 61.09 064: Metric: 57.76 128: Metric: 55.43 Current 001: Metric: 54.98 002: Metric: 56.56 004: Metric: 41.22 008: Metric: 35.96 016: Metric: 36.45 032: Metric: 35.71 064: Metric: 35.73 128: Metric: 34.96 With patch 001: Metric: 61.43 002: Metric: 81.64 004: Metric: 67.92 008: Metric: 51.67 016: Metric: 50.47 032: Metric: 52.29 064: Metric: 50.01 128: Metric: 49.04 So for low threads, it's not restored but for larger number of threads, it's closer to the "known good" baseline. Using a different mremap-intensive workload that is not representative of the real workload there is little difference observed outside of noise in the headline metrics However, the TLB shootdowns are reduced by 11% on average and at the peak, TLB shootdowns were reduced by 21%. Interrupts were sampled every second while the workload ran to get those figures. It's known that the figures will vary as the non-representative load is non-deterministic. An alternative patch was posted that should have significantly reduced the TLB flushes but unfortunately it does not perform as well as this version on the customer test case. If revisited, the two patches can stack on top of each other. Link: http://lkml.kernel.org/r/20180606183803.k7qaw2xnbvzshv34@techsingularity.net Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Aaron Lu <aaron.lu@intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-08mm: thp: check pmd migration entry in common pathZi Yan
When THP migration is being used, memory management code needs to handle pmd migration entries properly. This patch uses !pmd_present() or is_swap_pmd() (depending on whether pmd_none() needs separate code or not) to check pmd migration entries at the places where a pmd entry is present. Since pmd-related code uses split_huge_page(), split_huge_pmd(), pmd_trans_huge(), pmd_trans_unstable(), or pmd_none_or_trans_huge_or_clear_bad(), this patch: 1. adds pmd migration entry split code in split_huge_pmd(), 2. takes care of pmd migration entries whenever pmd_trans_huge() is present, 3. makes pmd_none_or_trans_huge_or_clear_bad() pmd migration entry aware. Since split_huge_page() uses split_huge_pmd() and pmd_trans_unstable() is equivalent to pmd_none_or_trans_huge_or_clear_bad(), we do not change them. Until this commit, a pmd entry should be: 1. pointing to a pte page, 2. is_swap_pmd(), 3. pmd_trans_huge(), 4. pmd_devmap(), or 5. pmd_none(). Signed-off-by: Zi Yan <zi.yan@cs.rutgers.edu> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David Nellans <dnellans@nvidia.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-09-06mm/mremap: fail map duplication attempts for private mappingsMike Kravetz
mremap will attempt to create a 'duplicate' mapping if old_size == 0 is specified. In the case of private mappings, mremap will actually create a fresh separate private mapping unrelated to the original. This does not fit with the design semantics of mremap as the intention is to create a new mapping based on the original. Therefore, return EINVAL in the case where an attempt is made to duplicate a private mapping. Also, print a warning message (once) if such an attempt is made. Link: http://lkml.kernel.org/r/cb9d9f6a-7095-582f-15a5-62643d65c736@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Aaron Lu <aaron.lu@intel.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-08-02userfaultfd: non-cooperative: notify about unmap of destination during mremapMike Rapoport
When mremap is called with MREMAP_FIXED it unmaps memory at the destination address without notifying userfaultfd monitor. If the destination were registered with userfaultfd, the monitor has no way to distinguish between the old and new ranges and to properly relate the page faults that would occur in the destination region. Fixes: 897ab3e0c49e ("userfaultfd: non-cooperative: add event for memory unmaps") Link: http://lkml.kernel.org/r/1500276876-3350-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-08-02mm, mprotect: flush TLB if potentially racing with a parallel reclaim ↵Mel Gorman
leaving stale TLB entries Nadav Amit identified a theoritical race between page reclaim and mprotect due to TLB flushes being batched outside of the PTL being held. He described the race as follows: CPU0 CPU1 ---- ---- user accesses memory using RW PTE [PTE now cached in TLB] try_to_unmap_one() ==> ptep_get_and_clear() ==> set_tlb_ubc_flush_pending() mprotect(addr, PROT_READ) ==> change_pte_range() ==> [ PTE non-present - no flush ] user writes using cached RW PTE ... try_to_unmap_flush() The same type of race exists for reads when protecting for PROT_NONE and also exists for operations that can leave an old TLB entry behind such as munmap, mremap and madvise. For some operations like mprotect, it's not necessarily a data integrity issue but it is a correctness issue as there is a window where an mprotect that limits access still allows access. For munmap, it's potentially a data integrity issue although the race is massive as an munmap, mmap and return to userspace must all complete between the window when reclaim drops the PTL and flushes the TLB. However, it's theoritically possible so handle this issue by flushing the mm if reclaim is potentially currently batching TLB flushes. Other instances where a flush is required for a present pte should be ok as either the page lock is held preventing parallel reclaim or a page reference count is elevated preventing a parallel free leading to corruption. In the case of page_mkclean there isn't an obvious path that userspace could take advantage of without using the operations that are guarded by this patch. Other users such as gup as a race with reclaim looks just at PTEs. huge page variants should be ok as they don't race with reclaim. mincore only looks at PTEs. userfault also should be ok as if a parallel reclaim takes place, it will either fault the page back in or read some of the data before the flush occurs triggering a fault. Note that a variant of this patch was acked by Andy Lutomirski but this was for the x86 parts on top of his PCID work which didn't make the 4.13 merge window as expected. His ack is dropped from this version and there will be a follow-on patch on top of PCID that will include his ack. [akpm@linux-foundation.org: tweak comments] [akpm@linux-foundation.org: fix spello] Link: http://lkml.kernel.org/r/20170717155523.emckq2esjro6hf3z@suse.de Reported-by: Nadav Amit <nadav.amit@gmail.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: <stable@vger.kernel.org> [v4.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-03-09mm: convert generic code to 5-level pagingKirill A. Shutemov
Convert all non-architecture-specific code to 5-level paging. It's mostly mechanical adding handling one more page table level in places where we deal with pud_t. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-24userfaultfd: non-cooperative: add event for memory unmapsMike Rapoport
When a non-cooperative userfaultfd monitor copies pages in the background, it may encounter regions that were already unmapped. Addition of UFFD_EVENT_UNMAP allows the uffd monitor to track precisely changes in the virtual memory layout. Since there might be different uffd contexts for the affected VMAs, we first should create a temporary representation for the unmap event for each uffd context and then notify them one by one to the appropriate userfault file descriptors. The event notification occurs after the mmap_sem has been released. [arnd@arndb.de: fix nommu build] Link: http://lkml.kernel.org/r/20170203165141.3665284-1-arnd@arndb.de [mhocko@suse.com: fix nommu build] Link: http://lkml.kernel.org/r/20170202091503.GA22823@dhcp22.suse.cz Link: http://lkml.kernel.org/r/1485542673-24387-3-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-22userfaultfd: non-cooperative: optimize mremap_userfaultfd_complete()Andrea Arcangeli
Optimize the mremap_userfaultfd_complete() interface to pass only the vm_userfaultfd_ctx pointer through the stack as a microoptimization. Link: http://lkml.kernel.org/r/20161216144821.5183-13-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Michael Rapoport <RAPOPORT@il.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-22userfaultfd: non-cooperative: add mremap() eventPavel Emelyanov
The event denotes that an area [start:end] moves to different location. Length change isn't reported as "new" addresses, if they appear on the uffd reader side they will not contain any data and the latter can just zeromap them. Waiting for the event ACK is also done outside of mmap sem, as for fork event. Link: http://lkml.kernel.org/r/20161216144821.5183-12-aarcange@redhat.com Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Michael Rapoport <RAPOPORT@il.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-11-29mremap: move_ptes: check pte dirty after its removalAaron Lu
Linus found there still is a race in mremap after commit 5d1904204c99 ("mremap: fix race between mremap() and page cleanning"). As described by Linus: "the issue is that another thread might make the pte be dirty (in the hardware walker, so no locking of ours will make any difference) *after* we checked whether it was dirty, but *before* we removed it from the page tables" Fix it by moving the check after we removed it from the page table. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-11-17mremap: fix race between mremap() and page cleanningAaron Lu
Prior to 3.15, there was a race between zap_pte_range() and page_mkclean() where writes to a page could be lost. Dave Hansen discovered by inspection that there is a similar race between move_ptes() and page_mkclean(). We've been able to reproduce the issue by enlarging the race window with a msleep(), but have not been able to hit it without modifying the code. So, we think it's a real issue, but is difficult or impossible to hit in practice. The zap_pte_range() issue is fixed by commit 1cf35d47712d("mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts"). And this patch is to fix the race between page_mkclean() and mremap(). Here is one possible way to hit the race: suppose a process mmapped a file with READ | WRITE and SHARED, it has two threads and they are bound to 2 different CPUs, e.g. CPU1 and CPU2. mmap returned X, then thread 1 did a write to addr X so that CPU1 now has a writable TLB for addr X on it. Thread 2 starts mremaping from addr X to Y while thread 1 cleaned the page and then did another write to the old addr X again. The 2nd write from thread 1 could succeed but the value will get lost. thread 1 thread 2 (bound to CPU1) (bound to CPU2) 1: write 1 to addr X to get a writeable TLB on this CPU 2: mremap starts 3: move_ptes emptied PTE for addr X and setup new PTE for addr Y and then dropped PTL for X and Y 4: page laundering for N by doing fadvise FADV_DONTNEED. When done, pageframe N is deemed clean. 5: *write 2 to addr X 6: tlb flush for addr X 7: munmap (Y, pagesize) to make the page unmapped 8: fadvise with FADV_DONTNEED again to kick the page off the pagecache 9: pread the page from file to verify the value. If 1 is there, it means we have lost the written 2. *the write may or may not cause segmentation fault, it depends on if the TLB is still on the CPU. Please note that this is only one specific way of how the race could occur, it didn't mean that the race could only occur in exact the above config, e.g. more than 2 threads could be involved and fadvise() could be done in another thread, etc. For anonymous pages, they could race between mremap() and page reclaim: THP: a huge PMD is moved by mremap to a new huge PMD, then the new huge PMD gets unmapped/splitted/pagedout before the flush tlb happened for the old huge PMD in move_page_tables() and we could still write data to it. The normal anonymous page has similar situation. To fix this, check for any dirty PTE in move_ptes()/move_huge_pmd() and if any, did the flush before dropping the PTL. If we did the flush for every move_ptes()/move_huge_pmd() call then we do not need to do the flush in move_pages_tables() for the whole range. But if we didn't, we still need to do the whole range flush. Alternatively, we can track which part of the range is flushed in move_ptes()/move_huge_pmd() and which didn't to avoid flushing the whole range in move_page_tables(). But that would require multiple tlb flushes for the different sub-ranges and should be less efficient than the single whole range flush. KBuild test on my Sandybridge desktop doesn't show any noticeable change. v4.9-rc4: real 5m14.048s user 32m19.800s sys 4m50.320s With this commit: real 5m13.888s user 32m19.330s sys 4m51.200s Reported-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-07-26mm: thp: check pmd_trans_unstable() after split_huge_pmd()Naoya Horiguchi
split_huge_pmd() doesn't guarantee that the pmd is normal pmd pointing to pte entries, which can be checked with pmd_trans_unstable(). Some callers make this assertion and some do it differently and some not, so let's do it in a unified manner. Link: http://lkml.kernel.org/r/1464741400-12143-1-git-send-email-n-horiguchi@ah.jp.nec.com Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-23mm: make mmap_sem for write waits killable for mm syscallsMichal Hocko
This is a follow up work for oom_reaper [1]. As the async OOM killing depends on oom_sem for read we would really appreciate if a holder for write didn't stood in the way. This patchset is changing many of down_write calls to be killable to help those cases when the writer is blocked and waiting for readers to release the lock and so help __oom_reap_task to process the oom victim. Most of the patches are really trivial because the lock is help from a shallow syscall paths where we can return EINTR trivially and allow the current task to die (note that EINTR will never get to the userspace as the task has fatal signal pending). Others seem to be easy as well as the callers are already handling fatal errors and bail and return to userspace which should be sufficient to handle the failure gracefully. I am not familiar with all those code paths so a deeper review is really appreciated. As this work is touching more areas which are not directly connected I have tried to keep the CC list as small as possible and people who I believed would be familiar are CCed only to the specific patches (all should have received the cover though). This patchset is based on linux-next and it depends on down_write_killable for rw_semaphores which got merged into tip locking/rwsem branch and it is merged into this next tree. I guess it would be easiest to route these patches via mmotm because of the dependency on the tip tree but if respective maintainers prefer other way I have no objections. I haven't covered all the mmap_write(mm->mmap_sem) instances here $ git grep "down_write(.*\<mmap_sem\>)" next/master | wc -l 98 $ git grep "down_write(.*\<mmap_sem\>)" | wc -l 62 I have tried to cover those which should be relatively easy to review in this series because this alone should be a nice improvement. Other places can be changed on top. [0] http://lkml.kernel.org/r/1456752417-9626-1-git-send-email-mhocko@kernel.org [1] http://lkml.kernel.org/r/1452094975-551-1-git-send-email-mhocko@kernel.org [2] http://lkml.kernel.org/r/1456750705-7141-1-git-send-email-mhocko@kernel.org This patch (of 18): This is the first step in making mmap_sem write waiters killable. It focuses on the trivial ones which are taking the lock early after entering the syscall and they are not changing state before. Therefore it is very easy to change them to use down_write_killable and immediately return with -EINTR. This will allow the waiter to pass away without blocking the mmap_sem which might be required to make a forward progress. E.g. the oom reaper will need the lock for reading to dismantle the OOM victim address space. The only tricky function in this patch is vm_mmap_pgoff which has many call sites via vm_mmap. To reduce the risk keep vm_mmap with the original non-killable semantic for now. vm_munmap callers do not bother checking the return value so open code it into the munmap syscall path for now for simplicity. Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-19huge pagecache: extend mremap pmd rmap lockout to filesHugh Dickins
Whatever huge pagecache implementation we go with, file rmap locking must be added to anon rmap locking, when mremap's move_page_tables() finds a pmd_trans_huge pmd entry: a simple change, let's do it now. Factor out take_rmap_locks() and drop_rmap_locks() to handle the locking for make move_ptes() and move_page_tables(), and delete the VM_BUG_ON_VMA which rejected vm_file and required anon_vma. Signed-off-by: Hugh Dickins <hughd@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Yang Shi <yang.shi@linaro.org> Cc: Ning Qu <quning@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-19huge mm: move_huge_pmd does not need new_vmaHugh Dickins
Remove move_huge_pmd()'s redundant new_vma arg: all it was used for was a VM_NOHUGEPAGE check on new_vma flags, but the new_vma is cloned from the old vma, so a trans_huge_pmd in the new_vma will be as acceptable as it was in the old vma, alignment and size permitting. Signed-off-by: Hugh Dickins <hughd@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Yang Shi <yang.shi@linaro.org> Cc: Ning Qu <quning@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-03-17mm: cleanup *pte_alloc* interfacesKirill A. Shutemov
There are few things about *pte_alloc*() helpers worth cleaning up: - 'vma' argument is unused, let's drop it; - most __pte_alloc() callers do speculative check for pmd_none(), before taking ptl: let's introduce pte_alloc() macro which does the check. The only direct user of __pte_alloc left is userfaultfd, which has different expectation about atomicity wrt pmd. - pte_alloc_map() and pte_alloc_map_lock() are redefined using pte_alloc(). [sudeep.holla@arm.com: fix build for arm64 hugetlbpage] [sfr@canb.auug.org.au: fix arch/arm/mm/mmu.c some more] Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-03-17mm: move max_map_count bits into mm.hAndrey Ryabinin
max_map_count sysctl unrelated to scheduler. Move its bits from include/linux/sched/sysctl.h to include/linux/mm.h. Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-02-11mm, dax: check for pmd_none() after split_huge_pmd()Kirill A. Shutemov
DAX implements split_huge_pmd() by clearing pmd. This simple approach reduces memory overhead, as we don't need to deposit page table on huge page mapping to make split_huge_pmd() never-fail. PTE table can be allocated and populated later on page fault from backing store. But one side effect is that have to check if pmd is pmd_none() after split_huge_pmd(). In most places we do this already to deal with parallel MADV_DONTNEED. But I found two call sites which is not affected by MADV_DONTNEED (due down_write(mmap_sem)), but need to have the check to work with DAX properly. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-15mm, thp: remove infrastructure for handling splitting PMDsKirill A. Shutemov
With new refcounting we don't need to mark PMDs splitting. Let's drop code to handle this. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Jerome Marchand <jmarchan@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Steve Capper <steve.capper@linaro.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-15thp: rename split_huge_page_pmd() to split_huge_pmd()Kirill A. Shutemov
We are going to decouple splitting THP PMD from splitting underlying compound page. This patch renames split_huge_page_pmd*() functions to split_huge_pmd*() to reflect the fact that it doesn't imply page splitting, only PMD. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Jerome Marchand <jmarchan@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Rik van Riel <riel@redhat.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Steve Capper <steve.capper@linaro.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-14mm: rework virtual memory accountingKonstantin Khlebnikov
When inspecting a vague code inside prctl(PR_SET_MM_MEM) call (which testing the RLIMIT_DATA value to figure out if we're allowed to assign new @start_brk, @brk, @start_data, @end_data from mm_struct) it's been commited that RLIMIT_DATA in a form it's implemented now doesn't do anything useful because most of user-space libraries use mmap() syscall for dynamic memory allocations. Linus suggested to convert RLIMIT_DATA rlimit into something suitable for anonymous memory accounting. But in this patch we go further, and the changes are bundled together as: * keep vma counting if CONFIG_PROC_FS=n, will be used for limits * replace mm->shared_vm with better defined mm->data_vm * account anonymous executable areas as executable * account file-backed growsdown/up areas as stack * drop struct file* argument from vm_stat_account * enforce RLIMIT_DATA for size of data areas This way code looks cleaner: now code/stack/data classification depends only on vm_flags state: VM_EXEC & ~VM_WRITE -> code (VmExe + VmLib in proc) VM_GROWSUP | VM_GROWSDOWN -> stack (VmStk) VM_WRITE & ~VM_SHARED & !stack -> data (VmData) The rest (VmSize - VmData - VmStk - VmExe - VmLib) could be called "shared", but that might be strange beast like readonly-private or VM_IO area. - RLIMIT_AS limits whole address space "VmSize" - RLIMIT_STACK limits stack "VmStk" (but each vma individually) - RLIMIT_DATA now limits "VmData" Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Kees Cook <keescook@google.com> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-05x86/mm/pat: Add untrack_pfn_moved for mremapToshi Kani
mremap() with MREMAP_FIXED on a VM_PFNMAP range causes the following WARN_ON_ONCE() message in untrack_pfn(). WARNING: CPU: 1 PID: 3493 at arch/x86/mm/pat.c:985 untrack_pfn+0xbd/0xd0() Call Trace: [<ffffffff817729ea>] dump_stack+0x45/0x57 [<ffffffff8109e4b6>] warn_slowpath_common+0x86/0xc0 [<ffffffff8109e5ea>] warn_slowpath_null+0x1a/0x20 [<ffffffff8106a88d>] untrack_pfn+0xbd/0xd0 [<ffffffff811d2d5e>] unmap_single_vma+0x80e/0x860 [<ffffffff811d3725>] unmap_vmas+0x55/0xb0 [<ffffffff811d916c>] unmap_region+0xac/0x120 [<ffffffff811db86a>] do_munmap+0x28a/0x460 [<ffffffff811dec33>] move_vma+0x1b3/0x2e0 [<ffffffff811df113>] SyS_mremap+0x3b3/0x510 [<ffffffff817793ee>] entry_SYSCALL_64_fastpath+0x12/0x71 MREMAP_FIXED moves a pfnmap from old vma to new vma. untrack_pfn() is called with the old vma after its pfnmap page table has been removed, which causes follow_phys() to fail. The new vma has a new pfnmap to the same pfn & cache type with VM_PAT set. Therefore, we only need to clear VM_PAT from the old vma in this case. Add untrack_pfn_moved(), which clears VM_PAT from a given old vma. move_vma() is changed to call this function with the old vma when VM_PFNMAP is set. move_vma() then calls do_munmap(), and untrack_pfn() is a no-op since VM_PAT is cleared. Reported-by: Stas Sergeev <stsp@list.ru> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Borislav Petkov <bp@suse.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/1450832064-10093-2-git-send-email-toshi.kani@hpe.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-11-05mm/mremap: use offset_in_page macroAlexander Kuleshov
linux/mm.h provides offset_in_page() macro. Let's use already predefined macro instead of (addr & ~PAGE_MASK). Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-09-04mremap: simplify the "overlap" check in mremap_to()Oleg Nesterov
Minor, but this check is overcomplicated. Two half-intervals do NOT overlap if END1 <= START2 || END2 <= START1, mremap_to() just needs to negate this check. Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Hugh Dickins <hughd@google.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Laurent Dufour <ldufour@linux.vnet.ibm.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-09-04mremap: don't do uneccesary checks if new_len == old_lenOleg Nesterov
The "new_len > old_len" branch in vma_to_resize() looks very confusing. It only covers the VM_DONTEXPAND/pgoff checks but everything below is equally unneeded if new_len == old_len. Change this code to return if "new_len == old_len", new_len < old_len is not possible, otherwise the code below is wrong anyway. Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Hugh Dickins <hughd@google.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Laurent Dufour <ldufour@linux.vnet.ibm.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-09-04mremap: don't do mm_populate(new_addr) on failureOleg Nesterov
move_vma() sets *locked even if move_page_tables() or ->mremap() fails, change sys_mremap() to check "ret & ~PAGE_MASK". I think we should simply remove the VM_LOCKED code in move_vma(), that is why this patch doesn't change move_vma(). But this needs more cleanups. Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Hugh Dickins <hughd@google.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Laurent Dufour <ldufour@linux.vnet.ibm.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-09-04mm: move ->mremap() from file_operations to vm_operations_structOleg Nesterov
vma->vm_ops->mremap() looks more natural and clean in move_vma(), and this way ->mremap() can have more users. Say, vdso. While at it, s/aio_ring_remap/aio_ring_mremap/. Note: this is the minimal change before ->mremap() finds another user in file_operations; this method should have more arguments, and it can be used to kill arch_remap(). Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Pavel Emelyanov <xemul@parallels.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Hugh Dickins <hughd@google.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-09-04mremap: don't leak new_vma if f_op->mremap() failsOleg Nesterov
move_vma() can't just return if f_op->mremap() fails, we should unmap the new vma like we do if move_page_tables() fails. To avoid the code duplication this patch moves the "move entries back" under the new "if (err)" branch. Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Hugh Dickins <hughd@google.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-06-24mm: new arch_remap() hookLaurent Dufour
Some architectures would like to be triggered when a memory area is moved through the mremap system call. This patch introduces a new arch_remap() mm hook which is placed in the path of mremap, and is called before the old area is unmapped (and the arch_unmap() hook is called). Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-15mm/mremap.c: clean up goto just return ERR_PTRDerek
As suggested by Kirill the "goto"s in vma_to_resize aren't necessary, just change them to explicit return. Signed-off-by: Derek Che <crquan@ymail.com> Suggested-by: "Kirill A. Shutemov" <kirill@shutemov.name> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-15mremap should return -ENOMEM when __vm_enough_memory failDerek
Recently I straced bash behavior in this dd zero pipe to read test, in part of testing under vm.overcommit_memory=2 (OVERCOMMIT_NEVER mode): # dd if=/dev/zero | read x The bash sub shell is calling mremap to reallocate more and more memory untill it finally failed -ENOMEM (I expect), or to be killed by system OOM killer (which should not happen under OVERCOMMIT_NEVER mode); But the mremap system call actually failed of -EFAULT, which is a surprise to me, I think it's supposed to be -ENOMEM? then I wrote this piece of C code testing confirmed it: https://gist.github.com/crquan/326bde37e1ddda8effe5 $ ./remap allocated one page @0x7f686bf71000, (PAGE_SIZE: 4096) grabbed 7680512000 bytes of memory (1875125 pages) @ 00007f6690993000. mremap failed Bad address (14). The -EFAULT comes from the branch of security_vm_enough_memory_mm failure, underlyingly it calls __vm_enough_memory which returns only 0 for success or -ENOMEM; So why vma_to_resize needs to return -EFAULT in this case? this sounds like a mistake to me. Some more digging into git history: 1) Before commit 119f657c7 ("RLIMIT_AS checking fix") in May 1 2005 (pre 2.6.12 days) it was returning -ENOMEM for this failure; 2) but commit 119f657c7 ("untangling do_mremap(), part 1") changed it accidentally, to what ever is preserved in local ret, which happened to be -EFAULT, in a previous assignment; 3) then in commit 54f5de709 code refactoring, it's explicitly returning -EFAULT, should be wrong. Signed-off-by: Derek Che <crquan@ymail.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-06fix mremap() vs. ioctx_kill() raceAl Viro
teach ->mremap() method to return an error and have it fail for aio mappings in process of being killed Note that in case of ->mremap() failure we need to undo move_page_tables() we'd already done; we could call ->mremap() first, but then the failure of move_page_tables() would require undoing whatever _successful_ ->mremap() has done, which would be a lot more headache in general. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-02-10mm: remove rest usage of VM_NONLINEAR and pte_file()Kirill A. Shutemov
One bit in ->vm_flags is unused now! Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-12-14Merge git://git.kvack.org/~bcrl/aio-nextLinus Torvalds
Pull aio updates from Benjamin LaHaise. * git://git.kvack.org/~bcrl/aio-next: aio: Skip timer for io_getevents if timeout=0 aio: Make it possible to remap aio ring
2014-12-13aio: Make it possible to remap aio ringPavel Emelyanov
There are actually two issues this patch addresses. Let me start with the one I tried to solve in the beginning. So, in the checkpoint-restore project (criu) we try to dump tasks' state and restore one back exactly as it was. One of the tasks' state bits is rings set up with io_setup() call. There's (almost) no problems in dumping them, there's a problem restoring them -- if I dump a task with aio ring originally mapped at address A, I want to restore one back at exactly the same address A. Unfortunately, the io_setup() does not allow for that -- it mmaps the ring at whatever place mm finds appropriate (it calls do_mmap_pgoff() with zero address and without the MAP_FIXED flag). To make restore possible I'm going to mremap() the freshly created ring into the address A (under which it was seen before dump). The problem is that the ring's virtual address is passed back to the user-space as the context ID and this ID is then used as search key by all the other io_foo() calls. Reworking this ID to be just some integer doesn't seem to work, as this value is already used by libaio as a pointer using which this library accesses memory for aio meta-data. So, to make restore work we need to make sure that a) ring is mapped at desired virtual address b) kioctx->user_id matches this value Having said that, the patch makes mremap() on aio region update the kioctx's user_id and mmap_base values. Here appears the 2nd issue I mentioned in the beginning of this mail. If (regardless of the C/R dances I do) someone creates an io context with io_setup(), then mremap()-s the ring and then destroys the context, the kill_ioctx() routine will call munmap() on wrong (old) address. This will result in a) aio ring remaining in memory and b) some other vma get unexpectedly unmapped. What do you think? Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Acked-by: Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
2014-12-13mm: convert i_mmap_mutex to rwsemDavidlohr Bueso
The i_mmap_mutex is a close cousin of the anon vma lock, both protecting similar data, one for file backed pages and the other for anon memory. To this end, this lock can also be a rwsem. In addition, there are some important opportunities to share the lock when there are no tree modifications. This conversion is straightforward. For now, all users take the write lock. [sfr@canb.auug.org.au: update fremap.c] Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: "Kirill A. Shutemov" <kirill@shutemov.name> Acked-by: Hugh Dickins <hughd@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-12-13mm: use new helper functions around the i_mmap_mutexDavidlohr Bueso
Convert all open coded mutex_lock/unlock calls to the i_mmap_[lock/unlock]_write() helpers. Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: "Kirill A. Shutemov" <kirill@shutemov.name> Acked-by: Hugh Dickins <hughd@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-09mm/mremap.c: use linux headersPaul McQuade
"WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>" Signed-off-by: Paul McQuade <paulmcquad@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-09mm: convert a few VM_BUG_ON callers to VM_BUG_ON_VMASasha Levin
Trivially convert a few VM_BUG_ON calls to VM_BUG_ON_VMA to extract more information when they trigger. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michel Lespinasse <walken@google.com> Cc: Minchan Kim <minchan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-05-11mm, thp: close race between mremap() and split_huge_page()Kirill A. Shutemov
It's critical for split_huge_page() (and migration) to catch and freeze all PMDs on rmap walk. It gets tricky if there's concurrent fork() or mremap() since usually we copy/move page table entries on dup_mm() or move_page_tables() without rmap lock taken. To get it work we rely on rmap walk order to not miss any entry. We expect to see destination VMA after source one to work correctly. But after switching rmap implementation to interval tree it's not always possible to preserve expected walk order. It works fine for dup_mm() since new VMA has the same vma_start_pgoff() / vma_last_pgoff() and explicitly insert dst VMA after src one with vma_interval_tree_insert_after(). But on move_vma() destination VMA can be merged into adjacent one and as result shifted left in interval tree. Fortunately, we can detect the situation and prevent race with rmap walk by moving page table entries under rmap lock. See commit 38a76013ad80. Problem is that we miss the lock when we move transhuge PMD. Most likely this bug caused the crash[1]. [1] http://thread.gmane.org/gmane.linux.kernel.mm/96473 Fixes: 108d6642ad81 ("mm anon rmap: remove anon_vma_moveto_tail") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Acked-by: Michel Lespinasse <walken@google.com> Cc: Dave Jones <davej@redhat.com> Cc: David Miller <davem@davemloft.net> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> [3.7+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-10-16mm: revert mremap pud_free anti-fixHugh Dickins
Revert commit 1ecfd533f4c5 ("mm/mremap.c: call pud_free() after fail calling pmd_alloc()"). The original code was correct: pud_alloc(), pmd_alloc(), pte_alloc_map() ensure that the pud, pmd, pt is already allocated, and seldom do they need to allocate; on failure, upper levels are freed if appropriate by the subsequent do_munmap(). Whereas commit 1ecfd533f4c5 did an unconditional pud_free() of a most-likely still-in-use pud: saved only by the near-impossiblity of pmd_alloc() failing. Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Chen Gang <gang.chen@asianux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-11mm/mremap.c: call pud_free() after fail calling pmd_alloc()Chen Gang
In alloc_new_pmd(), if pud_alloc() was called successfully, but pmd_alloc() fails, avoid leaking `pud'. Signed-off-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-08-27mm: move_ptes -- Set soft dirty bit depending on pte typeCyrill Gorcunov
Dave reported corrupted swap entries | [ 4588.541886] swap_free: Unused swap offset entry 00002d15 | [ 4588.541952] BUG: Bad page map in process trinity-kid12 pte:005a2a80 pmd:22c01f067 and Hugh pointed that in move_ptes _PAGE_SOFT_DIRTY bit set regardless the type of entry pte consists of. The trick here is that when we carry soft dirty status in swap entries we are to use _PAGE_SWP_SOFT_DIRTY instead, because this is the only place in pte which can be used for own needs without intersecting with bits owned by swap entry type/offset. Reported-and-tested-by: Dave Jones <davej@redhat.com> Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Analyzed-by: Hugh Dickins <hughd@google.com> Cc: Hillf Danton <dhillf@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-09mm: mremap: validate input before taking lockRasmus Villemoes
This patch is very similar to commit 84d96d897671 ("mm: madvise: complete input validation before taking lock"): perform some basic validation of the input to mremap() before taking the &current->mm->mmap_sem lock. This also makes the MREMAP_FIXED => MREMAP_MAYMOVE dependency slightly more explicit. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03mm: soft-dirty bits for user memory changes trackingPavel Emelyanov
The soft-dirty is a bit on a PTE which helps to track which pages a task writes to. In order to do this tracking one should 1. Clear soft-dirty bits from PTEs ("echo 4 > /proc/PID/clear_refs) 2. Wait some time. 3. Read soft-dirty bits (55'th in /proc/PID/pagemap2 entries) To do this tracking, the writable bit is cleared from PTEs when the soft-dirty bit is. Thus, after this, when the task tries to modify a page at some virtual address the #PF occurs and the kernel sets the soft-dirty bit on the respective PTE. Note, that although all the task's address space is marked as r/o after the soft-dirty bits clear, the #PF-s that occur after that are processed fast. This is so, since the pages are still mapped to physical memory, and thus all the kernel does is finds this fact out and puts back writable, dirty and soft-dirty bits on the PTE. Another thing to note, is that when mremap moves PTEs they are marked with soft-dirty as well, since from the user perspective mremap modifies the virtual memory at mremap's new address. Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Glauber Costa <glommer@parallels.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-23mm/rmap: rename anon_vma_unlock() => anon_vma_unlock_write()Konstantin Khlebnikov
The comment in commit 4fc3f1d66b1e ("mm/rmap, migration: Make rmap_walk_anon() and try_to_unmap_anon() more scalable") says: | Rename anon_vma_[un]lock() => anon_vma_[un]lock_write(), | to make it clearer that it's an exclusive write-lock in | that case - suggested by Rik van Riel. But that commit renames only anon_vma_lock() Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Ingo Molnar <mingo@kernel.org> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-23mm: use mm_populate() for mremap() of VM_LOCKED vmasMichel Lespinasse
Signed-off-by: Michel Lespinasse <walken@google.com> Acked-by: Rik van Riel <riel@redhat.com> Tested-by: Andy Lutomirski <luto@amacapital.net> Cc: Greg Ungerer <gregungerer@westnet.com.au> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-07sched: Move sched.h sysctl bits into separate headerClark Williams
Move the sysctl-related bits from include/linux/sched.h into a new file: include/linux/sched/sysctl.h. Then update source files requiring access to those bits by including the new header file. Signed-off-by: Clark Williams <williams@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20130207094659.06dced96@riff.lan Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-12-16Merge tag 'balancenuma-v11' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma Pull Automatic NUMA Balancing bare-bones from Mel Gorman: "There are three implementations for NUMA balancing, this tree (balancenuma), numacore which has been developed in tip/master and autonuma which is in aa.git. In almost all respects balancenuma is the dumbest of the three because its main impact is on the VM side with no attempt to be smart about scheduling. In the interest of getting the ball rolling, it would be desirable to see this much merged for 3.8 with the view to building scheduler smarts on top and adapting the VM where required for 3.9. The most recent set of comparisons available from different people are mel: https://lkml.org/lkml/2012/12/9/108 mingo: https://lkml.org/lkml/2012/12/7/331 tglx: https://lkml.org/lkml/2012/12/10/437 srikar: https://lkml.org/lkml/2012/12/10/397 The results are a mixed bag. In my own tests, balancenuma does reasonably well. It's dumb as rocks and does not regress against mainline. On the other hand, Ingo's tests shows that balancenuma is incapable of converging for this workloads driven by perf which is bad but is potentially explained by the lack of scheduler smarts. Thomas' results show balancenuma improves on mainline but falls far short of numacore or autonuma. Srikar's results indicate we all suffer on a large machine with imbalanced node sizes. My own testing showed that recent numacore results have improved dramatically, particularly in the last week but not universally. We've butted heads heavily on system CPU usage and high levels of migration even when it shows that overall performance is better. There are also cases where it regresses. Of interest is that for specjbb in some configurations it will regress for lower numbers of warehouses and show gains for higher numbers which is not reported by the tool by default and sometimes missed in treports. Recently I reported for numacore that the JVM was crashing with NullPointerExceptions but currently it's unclear what the source of this problem is. Initially I thought it was in how numacore batch handles PTEs but I'm no longer think this is the case. It's possible numacore is just able to trigger it due to higher rates of migration. These reports were quite late in the cycle so I/we would like to start with this tree as it contains much of the code we can agree on and has not changed significantly over the last 2-3 weeks." * tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma: (50 commits) mm/rmap, migration: Make rmap_walk_anon() and try_to_unmap_anon() more scalable mm/rmap: Convert the struct anon_vma::mutex to an rwsem mm: migrate: Account a transhuge page properly when rate limiting mm: numa: Account for failed allocations and isolations as migration failures mm: numa: Add THP migration for the NUMA working set scanning fault case build fix mm: numa: Add THP migration for the NUMA working set scanning fault case. mm: sched: numa: Delay PTE scanning until a task is scheduled on a new node mm: sched: numa: Control enabling and disabling of NUMA balancing if !SCHED_DEBUG mm: sched: numa: Control enabling and disabling of NUMA balancing mm: sched: Adapt the scanning rate if a NUMA hinting fault does not migrate mm: numa: Use a two-stage filter to restrict pages being migrated for unlikely task<->node relationships mm: numa: migrate: Set last_nid on newly allocated page mm: numa: split_huge_page: Transfer last_nid on tail page mm: numa: Introduce last_nid to the page frame sched: numa: Slowly increase the scanning period as NUMA faults are handled mm: numa: Rate limit setting of pte_numa if node is saturated mm: numa: Rate limit the amount of memory that is migrated between nodes mm: numa: Structures for Migrate On Fault per NUMA migration rate limiting mm: numa: Migrate pages handled during a pmd_numa hinting fault mm: numa: Migrate on reference policy ...