| Age | Commit message (Collapse) | Author |
|---|
|
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Drop license boilerplate (obsoleted by SPDX license IDs),
by Sven Eckelmann
- Drop documentation for sysfs and debugfs Documentation,
by Sven Eckelmann (2 patches)
- Mark sysfs as optional and deprecated, by Sven Eckelmann (3 patches)
- Update MAINTAINERS Tree, Chat and Bugtracker,
by Sven Eckelmann (3 patches)
- Rename batadv_dat_send_data, by Sven Eckelmann
- update DAT entries with incoming ARP replies, by Linus Luessing
- add multicast-to-unicast support for limited destinations,
by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch multicast packets with a limited number of destinations
(current default: 16) will be split and transmitted by the originator as
individual unicast transmissions.
Wifi broadcasts with their low bitrate are still a costly undertaking.
In a mesh network this cost multiplies with the overall size of the mesh
network. Therefore using multiple unicast transmissions instead of
broadcast flooding is almost always less burdensome for the mesh
network.
The maximum amount of unicast packets can be configured via the newly
introduced multicast_fanout parameter. If this limit is exceeded
distribution will fall back to classic broadcast flooding.
The multicast-to-unicast conversion is performed on the initial
multicast sender node and counts on a final destination node, mesh-wide
basis (and not next hop, neighbor node basis).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
All files got a SPDX-License-Identifier with commit 7db7d9f369a4
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic netlink code is expected to trigger notification messages when
configuration might have been changed. But the configuration of batman-adv
is most of the time still done using sysfs. So the sysfs interface should
also trigger the corresponding netlink messages via the "config" multicast
group.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The B.A.T.M.A.N. V implementation tries to estimate the link throughput of
an interface to an originator using different automatic methods. It is
still possible to overwrite it the link throughput for all reachable
originators via this interface.
The BATADV_CMD_SET_HARDIF/BATADV_CMD_GET_HARDIF commands allow to set/get
the configuration of this feature using the u32
BATADV_ATTR_THROUGHPUT_OVERRIDE attribute. The used unit is in 100 Kbit/s.
If the value is set to 0 then batman-adv will try to estimate the
throughput by itself.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ELP packets are transmitted every elp_interval milliseconds on an
slave/hard-interface. This value can be changed using the configuration
interface.
The BATADV_CMD_SET_HARDIF/BATADV_CMD_GET_HARDIF commands allow to set/get
the configuration of this feature using the u32 BATADV_ATTR_ELP_INTERVAL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The OGM packets are transmitted every orig_interval milliseconds. This
value can be changed using the configuration interface.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u32 BATADV_ATTR_ORIG_INTERVAL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can use (in an homogeneous mesh) network coding, a
mechanism that aims to increase the overall network throughput by fusing
multiple packets in one transmission.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_NETWORK_CODING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can optimize the flooding of multicast packets based on
the content of the global translation tables. To disable this behavior and
use the broadcast-like flooding of the packets, forceflood has to be
enabled.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_MULTICAST_FORCEFLOOD_ENABLED attribute. Setting the u8 to zero
will disable this feature (allowing multicast optimizations) and setting it
to something else is enabling this feature (forcing simple flooding).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In contrast to other modules, batman-adv allows to set the debug message
verbosity per mesh/soft-interface and not per module (via modparam).
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u32 (bitmask) BATADV_ATTR_LOG_LEVEL
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The TQ (B.A.T.M.A.N. IV) and throughput values (B.A.T.M.A.N. V) are reduced
when they are forwarded. One of the reductions is the penalty for
traversing an additional hop. This hop_penalty (0-255) defines the
percentage of reduction (0-100%).
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u8 BATADV_ATTR_HOP_PENALTY
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh/soft-interface can optimize the handling of DHCP packets. Instead
of flooding them through the whole mesh, it can be forwarded as unicast to
a specific gateway server. The originator which injects the packets in the
mesh has to select (based on sel_class thresholds) a responsible gateway
server. This is done by switching this originator to the gw_mode client.
The servers announce their forwarding bandwidth (download/upload) when the
gw_mode server was selected.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the attributes:
* u8 BATADV_ATTR_GW_MODE (0 == off, 1 == client, 2 == server)
* u32 BATADV_ATTR_GW_BANDWIDTH_DOWN (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_BANDWIDTH_UP (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_SEL_CLASS
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can fragment unicast packets when the packet size
exceeds the outgoing slave/hard-interface MTU.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_FRAGMENTATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can use a distributed hash table to answer ARP requests
without flooding the request through the whole mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can try to detect loops in the same mesh caused by
(indirectly) bridged mesh/soft-interfaces of different nodes. Some of the
loops can also be resolved without breaking the mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can use multiple slave/hard-interface ports at the same
time to transport the traffic to other nodes.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_BONDING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can drop messages between clients to implement a
mesh-wide AP isolation.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH and
BATADV_CMD_SET_VLAN/BATADV_CMD_GET_VLAN commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AP_ISOLATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
This feature also requires that skbuff which should be handled as isolated
are marked. The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to
set/get the mark/mask using the u32 attributes BATADV_ATTR_ISOLATION_MARK
and BATADV_ATTR_ISOLATION_MASK.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can delay OGM messages to aggregate different ogms
together in a single OGM packet.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AGGREGATED_OGMS_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the VLANs on top of
the mesh/soft-interface have configuration settings. The genl interface
reflects this by allowing to get/set it using the vlan specific commands
BATADV_CMD_GET_VLAN/BATADV_CMD_SET_VLAN.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_VLAN command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the
slave/hard-interface have B.A.T.M.A.N. V specific configuration settings.
The genl interface reflects this by allowing to get/set it using the
hard-interface specific commands.
The BATADV_CMD_GET_HARDIFS (or short version BATADV_CMD_GET_HARDIF) is
reused as get command because it already allow sto dump the content of
other information from the slave/hard-interface which are not yet
configuration specific.
The set command BATADV_CMD_SET_HARDIF will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_HARDIF
command message type that settings might have been changed and what the
current values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
The main objects for this configuration is the mesh/soft-interface object.
Its actual object in memory already contains most of the available
configuration settings. The genl interface reflects this by allowing to
get/set it using the mesh specific commands.
The BATADV_CMD_GET_MESH_INFO (or short version BATADV_CMD_GET_MESH) is
reused as get command because it already provides the content of other
information from the mesh/soft-interface which are not yet configuration
specific.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_MESH command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit ff4c92d85c6f ("genetlink: introduce pre_doit/post_doit hooks")
intoduced a mechanism to run specific code for doit hooks before/after the
hooks are run. Since all doit hooks are requiring the batadv softif, it
should be retrieved/freed in these helpers to simplify the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Dump the list of multicast flags entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Dump the list of DAT cache entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The genl_ops don't need to be written by anyone and thus can be moved in a
ro memory range.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Fixes: 56989f6d8568 ("genetlink: mark families as __ro_after_init")
Fixes: 2ae0f17df1cd ("genetlink: use idr to track families")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the netnsof flag on the family structure, indicating it can
be used with different network name spaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Dump the list of bridge loop avoidance backbones via the netlink socket.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The bridge loop avoidange is the main information for the debugging of of
bridge loop detection problems. It is therefore necessary when comparing
the bla claim tables.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Dump the list of bridge loop avoidance claims via the netlink socket.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: add policy for attributes, fix includes, fix
soft_iface reference leak]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[sw@simonwunderlich.de: fix kerneldoc, fix error reporting]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Add BATADV_CMD_GET_GATEWAYS commands, using handlers bat_gw_dump in
batadv_algo_ops. Will always return -EOPNOTSUPP for now, as no
implementations exist yet.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Dump the algo V originators and neighbours.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Fix includes, fix algo_ops integration]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Fix function parameter alignments,
add policy for attributes, fix includes, fix algo_ops integration]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Add BATADV_CMD_GET_ORIGINATORS and BATADV_CMD_GET_NEIGHBORS commands,
using handlers bat_orig_dump and bat_neigh_dump in batadv_algo_ops. Will
always return -EOPNOTSUPP for now, as no implementations exist yet.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Rewrite based on new algo_ops structures]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The TTVN is the main information for the debugging of translation table
problems. It is therefore necessary when comparing the global translation
tables.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
This adds the commands BATADV_CMD_GET_TRANSTABLE_LOCAL and
BATADV_CMD_GET_TRANSTABLE_GLOBAL, which correspond to the transtable_local
and transtable_global debugfs files.
The batadv_tt_client_flags enum is moved to the UAPI to expose it as part
of the netlink API.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: add policy for attributes, fix includes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[sw@simonwunderlich.de: fix VID attributes content]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
