| Age | Commit message (Collapse) | Author |
|---|
|
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.
As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.
Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.
It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point. The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.
Fixes: 30c8bd5aa8b2 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__netif_receive_skb_list_ptype() leaves skb->next poisoned before passing
it to pt_prev->func handler, what may produce (in certain cases, e.g. DSA
setup) crashes like:
[ 88.606777] CPU 0 Unable to handle kernel paging request at virtual address 0000000e, epc == 80687078, ra == 8052cc7c
[ 88.618666] Oops[#1]:
[ 88.621196] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-rc2-dlink-00206-g4192a172-dirty #1473
[ 88.630885] $ 0 : 00000000 10000400 00000002 864d7850
[ 88.636709] $ 4 : 87c0ddf0 864d7800 87c0ddf0 00000000
[ 88.642526] $ 8 : 00000000 49600000 00000001 00000001
[ 88.648342] $12 : 00000000 c288617b dadbee27 25d17c41
[ 88.654159] $16 : 87c0ddf0 85cff080 80790000 fffffffd
[ 88.659975] $20 : 80797b20 ffffffff 00000001 864d7800
[ 88.665793] $24 : 00000000 8011e658
[ 88.671609] $28 : 80790000 87c0dbc0 87cabf00 8052cc7c
[ 88.677427] Hi : 00000003
[ 88.680622] Lo : 7b5b4220
[ 88.683840] epc : 80687078 vlan_dev_hard_start_xmit+0x1c/0x1a0
[ 88.690532] ra : 8052cc7c dev_hard_start_xmit+0xac/0x188
[ 88.696734] Status: 10000404 IEp
[ 88.700422] Cause : 50000008 (ExcCode 02)
[ 88.704874] BadVA : 0000000e
[ 88.708069] PrId : 0001a120 (MIPS interAptiv (multi))
[ 88.713005] Modules linked in:
[ 88.716407] Process swapper (pid: 0, threadinfo=(ptrval), task=(ptrval), tls=00000000)
[ 88.725219] Stack : 85f61c28 00000000 0000000e 80780000 87c0ddf0 85cff080 80790000 8052cc7c
[ 88.734529] 87cabf00 00000000 00000001 85f5fb40 807b0000 864d7850 87cabf00 807d0000
[ 88.743839] 864d7800 8655f600 00000000 85cff080 87c1c000 0000006a 00000000 8052d96c
[ 88.753149] 807a0000 8057adb8 87c0dcc8 87c0dc50 85cfff08 00000558 87cabf00 85f58c50
[ 88.762460] 00000002 85f58c00 864d7800 80543308 fffffff4 00000001 85f58c00 864d7800
[ 88.771770] ...
[ 88.774483] Call Trace:
[ 88.777199] [<80687078>] vlan_dev_hard_start_xmit+0x1c/0x1a0
[ 88.783504] [<8052cc7c>] dev_hard_start_xmit+0xac/0x188
[ 88.789326] [<8052d96c>] __dev_queue_xmit+0x6e8/0x7d4
[ 88.794955] [<805a8640>] ip_finish_output2+0x238/0x4d0
[ 88.800677] [<805ab6a0>] ip_output+0xc8/0x140
[ 88.805526] [<805a68f4>] ip_forward+0x364/0x560
[ 88.810567] [<805a4ff8>] ip_rcv+0x48/0xe4
[ 88.815030] [<80528d44>] __netif_receive_skb_one_core+0x44/0x58
[ 88.821635] [<8067f220>] dsa_switch_rcv+0x108/0x1ac
[ 88.827067] [<80528f80>] __netif_receive_skb_list_core+0x228/0x26c
[ 88.833951] [<8052ed84>] netif_receive_skb_list+0x1d4/0x394
[ 88.840160] [<80355a88>] lunar_rx_poll+0x38c/0x828
[ 88.845496] [<8052fa78>] net_rx_action+0x14c/0x3cc
[ 88.850835] [<806ad300>] __do_softirq+0x178/0x338
[ 88.856077] [<8012a2d4>] irq_exit+0xbc/0x100
[ 88.860846] [<802f8b70>] plat_irq_dispatch+0xc0/0x144
[ 88.866477] [<80105974>] handle_int+0x14c/0x158
[ 88.871516] [<806acfb0>] r4k_wait+0x30/0x40
[ 88.876462] Code: afb10014 8c8200a0 00803025 <9443000c> 94a20468 00000000 10620042 00a08025 9605046a
[ 88.887332]
[ 88.888982] ---[ end trace eb863d007da11cf1 ]---
[ 88.894122] Kernel panic - not syncing: Fatal exception in interrupt
[ 88.901202] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
Fix this by pulling skb off the sublist and zeroing skb->next pointer
before calling ptype callback.
Fixes: 88eb1944e18c ("net: core: propagate SKB lists through packet_type lookup")
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.
This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qdisc_pkt_len_init expects transport_header to be set for GSO packets.
Patch [1] skips transport_header validation for GSO packets that don't
have network_header set at the moment of calling virtio_net_hdr_to_skb,
and allows them to pass into the stack. After patch [2] no placeholder
value is assigned to transport_header if dissection fails, so this patch
adds a check to the place where the value of transport_header is used.
[1] https://patchwork.ozlabs.org/patch/1044429/
[2] https://patchwork.ozlabs.org/patch/1046122/
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two easily resolvable overlapping change conflicts, one in
TCP and one in the eBPF verifier.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit a25717d2b604 ("xdp: support simultaneous driver and
hw XDP attachment") users can load an XDP program for offload and
in native driver mode simultaneously. Allow a similar mix of
offload and SKB mode/generic XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In order to provide more meaningful messages to user when the process of
loading xdp program onto network interface failed, let's add extack
messages within dev_change_xdp_fd.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Assign a default net namespace to netdevs created by init_dummy_netdev().
Fixes a NULL pointer dereference caused by busy-polling a socket bound to
an iwlwifi wireless device, which bumps the per-net BUSYPOLLRXPACKETS stat
if napi_poll() received packets:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000190
IP: napi_busy_loop+0xd6/0x200
Call Trace:
sock_poll+0x5e/0x80
do_sys_poll+0x324/0x5a0
SyS_poll+0x6c/0xf0
do_syscall_64+0x6b/0x1f0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Fixes: 7db6b048da3b ("net: Commonize busy polling code to focus on napi_id instead of socket")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
|
|
This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.
Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.
To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may need to validate configuration of a device that's about to
be upped. Should the validation fail, there's currently no way to
communicate details of the failure to the user, beyond an error number.
To mend that, change __dev_open() to take an extack argument and pass it
from __dev_change_flags() and dev_open(), where it was propagated in the
previous patches.
Change __dev_open() to call call_netdevice_notifiers_extack() so that
the passed-in extack is attached to the NETDEV_PRE_UP notifier.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to propagate extack through NETDEV_PRE_UP, add a new function
call_netdevice_notifiers_extack() that primes the extack field of the
notifier info. Convert call_netdevice_notifiers() to a simple wrapper
around the new function that passes NULL for extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. The last missing API is __dev_change_flags().
Therefore extend __dev_change_flags() with and extra extack argument and
update the two existing users.
Since the function declaration line is changed anyway, name the struct
net_device argument to placate checkpatch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_change_flags().
Therefore extend dev_change_flags() with and extra extack argument and
update all users. Most of the calls end up just encoding NULL, but
several sites (VLAN, ipvlan, VRF, rtnetlink) do have extack available.
Since the function declaration line is changed anyway, name the other
function arguments to placate checkpatch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_open().
Therefore extend dev_open() with and extra extack argument and update
all users. Most of the calls end up just encoding NULL, but bond and
team drivers have the extack readily available.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
list_del() leaves the skb->next pointer poisoned, which can then lead to
a crash in e.g. OVS forwarding. For example, setting up an OVS VXLAN
forwarding bridge on sfc as per:
========
$ ovs-vsctl show
5dfd9c47-f04b-4aaa-aa96-4fbb0a522a30
Bridge "br0"
Port "br0"
Interface "br0"
type: internal
Port "enp6s0f0"
Interface "enp6s0f0"
Port "vxlan0"
Interface "vxlan0"
type: vxlan
options: {key="1", local_ip="10.0.0.5", remote_ip="10.0.0.4"}
ovs_version: "2.5.0"
========
(where 10.0.0.5 is an address on enp6s0f1)
and sending traffic across it will lead to the following panic:
========
general protection fault: 0000 [#1] SMP PTI
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 4.20.0-rc3-ehc+ #701
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:dev_hard_start_xmit+0x38/0x200
Code: 53 48 89 fb 48 83 ec 20 48 85 ff 48 89 54 24 08 48 89 4c 24 18 0f 84 ab 01 00 00 48 8d 86 90 00 00 00 48 89 f5 48 89 44 24 10 <4c> 8b 33 48 c7 03 00 00 00 00 48 8b 05 c7 d1 b3 00 4d 85 f6 0f 95
RSP: 0018:ffff888627b437e0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: dead000000000100 RCX: ffff88862279c000
RDX: ffff888614a342c0 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888618a88000 R08: 0000000000000001 R09: 00000000000003e8
R10: 0000000000000000 R11: ffff888614a34140 R12: 0000000000000000
R13: 0000000000000062 R14: dead000000000100 R15: ffff888616430000
FS: 0000000000000000(0000) GS:ffff888627b40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6d2bc6d000 CR3: 000000000200a000 CR4: 00000000000006e0
Call Trace:
<IRQ>
__dev_queue_xmit+0x623/0x870
? masked_flow_lookup+0xf7/0x220 [openvswitch]
? ep_poll_callback+0x101/0x310
do_execute_actions+0xaba/0xaf0 [openvswitch]
? __wake_up_common+0x8a/0x150
? __wake_up_common_lock+0x87/0xc0
? queue_userspace_packet+0x31c/0x5b0 [openvswitch]
ovs_execute_actions+0x47/0x120 [openvswitch]
ovs_dp_process_packet+0x7d/0x110 [openvswitch]
ovs_vport_receive+0x6e/0xd0 [openvswitch]
? dst_alloc+0x64/0x90
? rt_dst_alloc+0x50/0xd0
? ip_route_input_slow+0x19a/0x9a0
? __udp_enqueue_schedule_skb+0x198/0x1b0
? __udp4_lib_rcv+0x856/0xa30
? __udp4_lib_rcv+0x856/0xa30
? cpumask_next_and+0x19/0x20
? find_busiest_group+0x12d/0xcd0
netdev_frame_hook+0xce/0x150 [openvswitch]
__netif_receive_skb_core+0x205/0xae0
__netif_receive_skb_list_core+0x11e/0x220
netif_receive_skb_list+0x203/0x460
? __efx_rx_packet+0x335/0x5e0 [sfc]
efx_poll+0x182/0x320 [sfc]
net_rx_action+0x294/0x3c0
__do_softirq+0xca/0x297
irq_exit+0xa6/0xb0
do_IRQ+0x54/0xd0
common_interrupt+0xf/0xf
</IRQ>
========
So, in all listified-receive handling, instead pull skbs off the lists with
skb_list_del_init().
Fixes: 9af86f933894 ("net: core: fix use-after-free in __netif_receive_skb_list_core")
Fixes: 7da517a3bc52 ("net: core: Another step of skb receive list processing")
Fixes: a4ca8b7df73c ("net: ipv4: fix drop handling in ip_list_rcv() and ip_list_rcv_finish()")
Fixes: d8269e2cbf90 ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_napi_add() could report an error like this below due to it allows
to pass a format string for wildcarding before calling
dev_get_valid_name(),
"netif_napi_add() called with weight 256 on device eth%d"
For example, hns_enet_drv module does this.
hns_nic_try_get_ae
hns_nic_init_ring_data
netif_napi_add
register_netdev
dev_get_valid_name
Hence, make it a bit more human-readable by using netdev_err_once()
instead.
Signed-off-by: Qian Cai <cai@gmx.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trace events are already present for the receive entry points, to indicate
how the reception entered the stack.
This patch adds the corresponding exit trace events that will bound the
reception such that all events occurring between the entry and the exit
can be considered as part of the reception context. This greatly helps
for dependency and root cause analyses.
Without this, it is not possible with tracepoint instrumentation to
determine whether a sched_wakeup event following a netif_receive_skb
event is the result of the packet reception or a simple coincidence after
further processing by the thread. It is possible using other mechanisms
like kretprobes, but considering the "entry" points are already present,
it would be good to add the matching exit events.
In addition to linking packets with wakeups, the entry/exit event pair
can also be used to perform network stack latency analyses.
Signed-off-by: Geneviève Bastien <gbastien@versatic.net>
CC: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> (tracing side)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 04157469b7b8 ("net: Use static_key for XPS maps") introduced a
static key for XPS, but the increments/decrements don't match.
First, the static key's counter is incremented once for each queue, but
only decremented once for a whole batch of queues, leading to large
unbalances.
Second, the xps_rxqs_needed key is decremented whenever we reset a batch
of queues, whether they had any rxqs mapping or not, so that if we setup
cpu-XPS on em1 and RXQS-XPS on em2, resetting the queues on em1 would
decrement the xps_rxqs_needed key.
This reworks the accounting scheme so that the xps_needed key is
incremented only once for each type of XPS for all the queues on a
device, and the xps_rxqs_needed key is incremented only once for all
queues. This is sufficient to let us retrieve queues via
get_xps_queue().
This patch introduces a new reset_xps_maps(), which reinitializes and
frees the appropriate map (xps_rxqs_map or xps_cpus_map), and drops a
reference to the needed keys:
- both xps_needed and xps_rxqs_needed, in case of rxqs maps,
- only xps_needed, in case of CPU maps.
Now, we also need to call reset_xps_maps() at the end of
__netif_set_xps_queue() when there's no active map left, for example
when writing '00000000,00000000' to all queues' xps_rxqs setting.
Fixes: 04157469b7b8 ("net: Use static_key for XPS maps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 80d19669ecd3 ("net: Refactor XPS for CPUs and Rx queues"),
netif_reset_xps_queues() did netdev_queue_numa_node_write() for all the
queues being reset. Now, this is only done when the "active" variable in
clean_xps_maps() is false, ie when on all the CPUs, there's no active
XPS mapping left.
Fixes: 80d19669ecd3 ("net: Refactor XPS for CPUs and Rx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
We very often have few flows/chains to look at, and we
might increase GRO_HASH_BUCKETS to 32 or 64 in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric noted that with UDP GRO and NAPI timeout, we could keep a single
UDP packet inside the GRO hash forever, if the related NAPI instance
calls napi_gro_complete() at an higher frequency than the NAPI timeout.
Willem noted that even TCP packets could be trapped there, till the
next retransmission.
This patch tries to address the issue, flushing the old packets -
those with a NAPI_GRO_CB age before the current jiffy - before scheduling
the NAPI timeout. The rationale is that such a timeout should be
well below a jiffy and we are not flushing packets eligible for sane GRO.
v1 -> v2:
- clarified the commit message and comment
RFC -> v1:
- added 'Fixes tags', cleaned-up the wording.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 3b47d30396ba ("net: gro: add a per device gro flush timer")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab2033 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab2033 ("gro: Add internal interfaces for VLAN")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently netdev_rx_csum_fault() only shows a device name,
we need more information about the skb for debugging csum
failures.
Sample output:
ens3: hw csum failure
dev features: 0x0000000000014b89
skb len=84 data_len=0 pkt_type=0 gso_size=0 gso_type=0 nr_frags=0 ip_summed=0 csum=0 csum_complete_sw=0 csum_valid=0 csum_level=0
Note, I use pr_err() just to be consistent with the existing one.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes assumptions about VLAN_TAG_PRESENT bit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like with normal GRO processing, we have to initialize
skb->next to NULL when we unlink overflow packets from the
GRO hash lists.
Fixes: d4546c2509b1 ("net: Convert GRO SKB handling to list_head.")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 5aad1de5ea2c ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d738 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d738 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea2c ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XDP can modify (and resize) the Ethernet header in the packet.
There is a bug in generic-XDP, because skb->protocol and skb->pkt_type
are setup before reaching (netif_receive_)generic_xdp.
This bug was hit when XDP were popping VLAN headers (changing
eth->h_proto), as skb->protocol still contains VLAN-indication
(ETH_P_8021Q) causing invocation of skb_vlan_untag(skb), which corrupt
the packet (basically popping the VLAN again).
This patch catch if XDP changed eth header in such a way, that SKB
fields needs to be updated.
V2: on request from Song Liu, use ETH_HLEN instead of mac_len,
in __skb_push() as eth_type_trans() use ETH_HLEN in paired skb_pull_inline().
Fixes: d445516966dc ("net: xdp: support xdp generic on virtual devices")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
It documents what is happening, and eliminates the spurious list
pointer poisoning.
In the long term, in order to get proper list head debugging, we
might want to use the list poison value as the indicator that
an SKB is a singleton and not on a list.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the only way to ignore outgoing packets on a packet socket is
via the BPF filter. With MSG_ZEROCOPY, packets that are looped into
AF_PACKET are copied in dev_queue_xmit_nit(), and this copy happens even
if the filter run from packet_rcv() would reject them. So the presence
of a packet socket on the interface takes away the benefits of
MSG_ZEROCOPY, even if the packet socket is not interested in outgoing
packets. (Even when MSG_ZEROCOPY is not used, the skb is unnecessarily
cloned, but the cost for that is much lower.)
Add a socket option to allow AF_PACKET sockets to ignore outgoing
packets to solve this. Note that the *BSDs already have something
similar: BIOCSSEESENT/BIOCSDIRECTION and BIOCSDIRFILT.
The first intended user is lldpd.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The conversion of the hotplug notifiers to a state machine left the
notifier.h includes around in some places. Remove them.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1535114033-4605-1-git-send-email-mojha@codeaurora.org
|
|
The definition of static_key_slow_inc() has cpus_read_lock in place. In the
virtio_net driver, XPS queues are initialized after setting the queue:cpu
affinity in virtnet_set_affinity() which is already protected within
cpus_read_lock. Lockdep prints a warning when we are trying to acquire
cpus_read_lock when it is already held.
This patch adds an ability to call __netif_set_xps_queue under
cpus_read_lock().
Acked-by: Jason Wang <jasowang@redhat.com>
============================================
WARNING: possible recursive locking detected
4.18.0-rc3-next-20180703+ #1 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: static_key_slow_inc+0xe/0x20
but task is already holding lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(cpu_hotplug_lock.rw_sem);
lock(cpu_hotplug_lock.rw_sem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: 00000000244bc7da (&dev->mutex){....}, at: __driver_attach+0x5a/0x110
#1: 00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0
#2: 000000005cd8463f (xps_map_mutex){+.+.}, at: __netif_set_xps_queue+0x8d/0xc60
v2: move cpus_read_lock() out of __netif_set_xps_queue()
Cc: "Nambiar, Amritha" <amritha.nambiar@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Fixes: 8af2c06ff4b1 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_set_mtu_ext is able to fail with a valid mtu value, at that
condition, extack._msg is not set and random since it is in stack,
then kernel will crash when print it.
Fixes: 7a4c53bee3324a ("net: report invalid mtu value via netlink extack")
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is similar TC_ACT_REDIRECT, but with a slightly different
semantic:
- on ingress the mirred skbs are passed to the target device
network stack without any additional check not scrubbing.
- the rcu-protected stats provided via the tcf_result struct
are updated on error conditions.
This new tcfa_action value is not exposed to the user-space
and can be used only internally by clsact.
v1 -> v2: do not touch TC_ACT_REDIRECT code path, introduce
a new action type instead
v2 -> v3:
- rename the new action value TC_ACT_REINJECT, update the
helper accordingly
- take care of uncloned reinjected packets in XDP generic
hook
v3 -> v4:
- renamed again the new action value (JiriP)
v4 -> v5:
- fix build error with !NET_CLS_ACT (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
