| Age | Commit message (Collapse) | Author |
|---|
|
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All DSA tag receive functions do strictly the same thing after they have located
the originating source port from their tag specific protocol:
- push ETH_HLEN bytes
- set pkt_type to PACKET_HOST
- call eth_type_trans()
- bump up counters
- call netif_receive_skb()
Factor all of that into dsa_switch_rcv(). This also makes us return a pointer to
a sk_buff, which makes us symetric with the xmit function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the netdevice notifier block register code in slave.c and provide
helpers for dsa.c to register and unregister it.
At the same time, check for errors since (un)register_netdevice_notifier
may fail.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store a pointer to the dsa_port structure in the dsa_slave_priv
structure, instead of the switch/port index.
This will allow to store more information such as the bridge device,
needed in DSA drivers for multi-chip configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Isolate the HWMON support in DSA in its own file. Currently only the
legacy DSA code is concerned.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_driver_version string is irrelevant and has not been bumped
since its introduction about 9 years ago. Kill it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we can properly support multiple distinct trees in the system,
using a global variable: dsa_cpu_port_ethtool_ops is getting clobbered
as soon as the second switch tree gets probed, and we don't want that.
We need to move this to be dynamically allocated, and since we can't
really be comparing addresses anymore to determine first time
initialization versus any other times, just move this to dsa.c and
dsa2.c where the remainder of the dst/ds initialization happens.
The operations teardown restores the master netdev's ethtool_ops to its
original ethtool_ops pointer (typically within the Ethernet driver)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper function: dsa_cpu_port_ethtool_init() which initializes a
custom ethtool_ops structure with custom DSA ethtool operations for CPU
ports. This is a preliminary change to move the initialization outside
of net/dsa/slave.c.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the two switch statements with an array lookup, and store the
result in the dsa tree structure. The drivers no longer need to know
the selected tag protocol, so remove it from the dsa switch structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the code to setup a single DSA/CPU port into a function of
its own, and export it, so it can be used by the new binding.
Similarly, refactor the destroy code into a function. When destroying
the ports, don't put the of node. They should be released at the end
along with the normal ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_slave_priv structure does not need a pointer to its net_device.
Kill it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move dsa slave dedicated code from dsa_switch_destroy to a new
dsa_slave_destroy function in slave.c.
Add the netif_carrier_off and phy_disconnect calls in order to
correctly cleanup the netdev state and PHY state machine.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for using DSA slave network devices with netconsole, which
requires us to allocate and free custom netpoll instances and invoke the
parent network device poll controller callback.
In order for netconsole to work, we need to construct the DSA tag, but
not queue the skb for transmission on the master network device xmit
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All tagging protocols do the same thing: increment device statistics,
make room for the tag to be inserted, create the tag, invoke the parent
network device transmit function.
In order to prepare for adding netpoll support, which requires the tag
creation, but not using the parent network device transmit function, do
some little refactoring which eliminates duplication between the 4
tagging protocols supported.
We need to return a sk_buff pointer back to the caller because the tag
specific transmit function may have to reallocate the original skb (e.g:
tag_trailer.c) and this is the one we should be transmitting, not the
original sk_buff we were passed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the DSA slave interface to be bound to an arbitray PHY, not just
the ones that are available as child PHY devices of the switch MDIO bus.
This allows us for instance to have external PHYs connected to a
separate MDIO bus, but yet also connected to a given switch port.
Under certain configurations, the physical port mask might not be a 1:1
mapping to the MII PHYs mask. This is the case, if e.g: Port 1 of the
switch is used and connects to a PHY at a MDIO address different than 1.
Introduce a phys_mii_mask variable which allows driver to implement and
divert their own MDIO read/writes operations for a subset of the MDIO
PHY addresses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.
This patch proceeds with adding a new layer of abstraction and two new
functions:
dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c
dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c
When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.
A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.
This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Any headers included by drivers should be under include/, and
any definitions they use are not really private to the core as
the name "dsa_priv.h" suggests.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These files have circular dependencies, so if we make DSA modular then
they must be built into the same module. Therefore, link them
together and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eth_type_trans() will use these functions if DSA is enabled, which
blocks building DSA as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Trailer switch tagging format. This is
another tagging that doesn't explicitly mark tagged packets with a
distinct ethertype, so that we need to add a similar hack in the
receive path as for the Original DSA tagging format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the DSA switches currently in the field do not support the
Ethertype DSA tagging format that one of the previous patches added
support for, but only the original DSA tagging format.
The original DSA tagging format carries the same information as the
Ethertype DSA tagging format, but with the difference that it does not
have an ethertype field. In other words, when receiving a packet that
is tagged with an original DSA tag, there is no way of telling in
eth_type_trans() that this packet is in fact a DSA-tagged packet.
This patch adds a hook into eth_type_trans() which is only compiled in
if support for a switch chip that doesn't support Ethertype DSA is
selected, and which checks whether there is a DSA switch driver
instance attached to this network device which uses the old tag format.
If so, it sets the protocol field to ETH_P_DSA without looking at the
packet, so that the packet ends up in the right place.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
