| Age | Commit message (Collapse) | Author |
|---|
|
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because kfree_skb already checked NULL skb parameter,
so the additional checks are unnecessary, just remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.
Fixes: 6d6148bc78d2 ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To release hsr(upper) interface, it should release
its own lower interfaces first.
Then, hsr(upper) interface can be released safely.
In the current code of error path of hsr_dev_finalize(), it releases hsr
interface before releasing a lower interface.
So, a warning occurs, which warns about the leak of lower interfaces.
In order to fix this problem, changing the ordering of the error path of
hsr_dev_finalize() is needed.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
ip link add hsr1 type hsr slave1 dummy2 slave2 dummy0
Splat looks like:
[ 214.923127][ C2] WARNING: CPU: 2 PID: 1093 at net/core/dev.c:8992 rollback_registered_many+0x986/0xcf0
[ 214.923129][ C2] Modules linked in: hsr dummy openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipx
[ 214.923154][ C2] CPU: 2 PID: 1093 Comm: ip Not tainted 5.8.0-rc2+ #623
[ 214.923156][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 214.923157][ C2] RIP: 0010:rollback_registered_many+0x986/0xcf0
[ 214.923160][ C2] Code: 41 8b 4e cc 45 31 c0 31 d2 4c 89 ee 48 89 df e8 e0 47 ff ff 85 c0 0f 84 cd fc ff ff 5
[ 214.923162][ C2] RSP: 0018:ffff8880c5156f28 EFLAGS: 00010287
[ 214.923165][ C2] RAX: ffff8880d1dad458 RBX: ffff8880bd1b9000 RCX: ffffffffb929d243
[ 214.923167][ C2] RDX: 1ffffffff77e63f0 RSI: 0000000000000008 RDI: ffffffffbbf31f80
[ 214.923168][ C2] RBP: dffffc0000000000 R08: fffffbfff77e63f1 R09: fffffbfff77e63f1
[ 214.923170][ C2] R10: ffffffffbbf31f87 R11: 0000000000000001 R12: ffff8880c51570a0
[ 214.923172][ C2] R13: ffff8880bd1b90b8 R14: ffff8880c5157048 R15: ffff8880d1dacc40
[ 214.923174][ C2] FS: 00007fdd257a20c0(0000) GS:ffff8880da200000(0000) knlGS:0000000000000000
[ 214.923175][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 214.923177][ C2] CR2: 00007ffd78beb038 CR3: 00000000be544005 CR4: 00000000000606e0
[ 214.923179][ C2] Call Trace:
[ 214.923180][ C2] ? netif_set_real_num_tx_queues+0x780/0x780
[ 214.923182][ C2] ? dev_validate_mtu+0x140/0x140
[ 214.923183][ C2] ? synchronize_rcu.part.79+0x85/0xd0
[ 214.923185][ C2] ? synchronize_rcu_expedited+0xbb0/0xbb0
[ 214.923187][ C2] rollback_registered+0xc8/0x170
[ 214.923188][ C2] ? rollback_registered_many+0xcf0/0xcf0
[ 214.923190][ C2] unregister_netdevice_queue+0x18b/0x240
[ 214.923191][ C2] hsr_dev_finalize+0x56e/0x6e0 [hsr]
[ 214.923192][ C2] hsr_newlink+0x36b/0x450 [hsr]
[ 214.923194][ C2] ? hsr_dellink+0x70/0x70 [hsr]
[ 214.923195][ C2] ? rtnl_create_link+0x2e4/0xb00
[ 214.923197][ C2] ? __netlink_ns_capable+0xc3/0xf0
[ 214.923198][ C2] __rtnl_newlink+0xbdb/0x1270
[ ... ]
Fixes: e0a4b99773d3 ("hsr: use upper/lower device infrastructure")
Reported-by: syzbot+7f1c020f68dab95aab59@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is being deleted, "/proc/net/dev_snmp6/<interface name>"
is deleted.
The function for this is addrconf_ifdown() in the addrconf_notify() and
it is called by notification, which is NETDEV_UNREGISTER.
But, if NETDEV_CHANGEMTU is triggered after NETDEV_UNREGISTER,
this proc file will be created again.
This recreated proc file will be deleted by netdev_wati_allrefs().
Before netdev_wait_allrefs() is called, creating a new HSR interface
routine can be executed and It tries to create a proc file but it will
find an un-deleted proc file.
At this point, it warns about it.
To avoid this situation, it can use ->dellink() instead of
->ndo_uninit() to release resources because ->dellink() is called
before NETDEV_UNREGISTER.
So, a proc file will not be recreated.
Test commands
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 mtu 1300
#SHELL1
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
done
#SHELL2
while :
do
ip link del hsr0
done
Splat looks like:
[ 9888.980852][ T2752] proc_dir_entry 'dev_snmp6/hsr0' already registered
[ 9888.981797][ C2] WARNING: CPU: 2 PID: 2752 at fs/proc/generic.c:372 proc_register+0x2d5/0x430
[ 9888.981798][ C2] Modules linked in: hsr dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6x
[ 9888.981814][ C2] CPU: 2 PID: 2752 Comm: ip Tainted: G W 5.8.0-rc1+ #616
[ 9888.981815][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 9888.981816][ C2] RIP: 0010:proc_register+0x2d5/0x430
[ 9888.981818][ C2] Code: fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 65 01 00 00 49 8b b5 e0 00 00 00 48 89 ea 40
[ 9888.981819][ C2] RSP: 0018:ffff8880628dedf0 EFLAGS: 00010286
[ 9888.981821][ C2] RAX: dffffc0000000008 RBX: ffff888028c69170 RCX: ffffffffaae09a62
[ 9888.981822][ C2] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f75ac
[ 9888.981823][ C2] RBP: ffff888028c693f4 R08: ffffed100d9401bd R09: ffffed100d9401bd
[ 9888.981824][ C2] R10: ffffffffaddf406f R11: 0000000000000001 R12: ffff888028c69308
[ 9888.981825][ C2] R13: ffff8880663584c8 R14: dffffc0000000000 R15: ffffed100518d27e
[ 9888.981827][ C2] FS: 00007f3876b3b0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 9888.981828][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9888.981829][ C2] CR2: 00007f387601a8c0 CR3: 000000004101a002 CR4: 00000000000606e0
[ 9888.981830][ C2] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9888.981831][ C2] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9888.981832][ C2] Call Trace:
[ 9888.981833][ C2] ? snmp6_seq_show+0x180/0x180
[ 9888.981834][ C2] proc_create_single_data+0x7c/0xa0
[ 9888.981835][ C2] snmp6_register_dev+0xb0/0x130
[ 9888.981836][ C2] ipv6_add_dev+0x4b7/0xf60
[ 9888.981837][ C2] addrconf_notify+0x684/0x1ca0
[ 9888.981838][ C2] ? __mutex_unlock_slowpath+0xd0/0x670
[ 9888.981839][ C2] ? kasan_unpoison_shadow+0x30/0x40
[ 9888.981840][ C2] ? wait_for_completion+0x250/0x250
[ 9888.981841][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981842][ C2] ? dropmon_net_event+0x227/0x410
[ 9888.981843][ C2] ? notifier_call_chain+0x90/0x160
[ 9888.981844][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981845][ C2] notifier_call_chain+0x90/0x160
[ 9888.981846][ C2] register_netdevice+0xbe5/0x1070
[ ... ]
Reported-by: syzbot+1d51c8b74efa4c44adeb@syzkaller.appspotmail.com
Fixes: e0a4b99773d3 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
When VLAN frame is being sent, hsr calls WARN_ONCE() because hsr doesn't
support VLAN. But using WARN_ONCE() is overdoing.
Using netdev_warn_once() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When all hsr slave interfaces are removed, hsr interface doesn't work.
At that moment, it's fine to remove an unused hsr interface automatically
for saving resources.
That's a common behavior of virtual interfaces.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no callers in-tree anymore.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the hsr_dev_change_mtu(), the 'dev' and 'master->dev' pointer are
same. So, the 'master' variable and some code are unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: ee1c27977284 ("net/hsr: Added support for HSR v1")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the commit e0a4b99773d3 ("hsr: use upper/lower device infrastructure"),
dev_get() was removed but dev_put() in the error path wasn't removed.
So, if creating hsr interface command is failed, the reference counter leak
of lower interface would occur.
Test commands:
ip link add dummy0 type dummy
ip link add ipvlan0 link dummy0 type ipvlan mode l2
ip link add ipvlan1 link dummy0 type ipvlan mode l2
ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1
ip link del ipvlan0
Result:
[ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1
Fixes: e0a4b99773d3 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
node_db is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of hsr->list_lock.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_port_get_rcu() can return NULL, so we need to be careful.
general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
CPU: 1 PID: 10249 Comm: syz-executor.5 Not tainted 5.5.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:199 [inline]
RIP: 0010:hsr_addr_is_self+0x86/0x330 net/hsr/hsr_framereg.c:44
Code: 04 00 f3 f3 f3 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 e8 6b ff 94 f9 4c 89 f2 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 75 02 00 00 48 8b 43 30 49 39 c6 49 89 47 c0 0f
RSP: 0018:ffffc90000da8a90 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff87e0cc33
RDX: 0000000000000006 RSI: ffffffff87e035d5 RDI: 0000000000000000
RBP: ffffc90000da8b20 R08: ffff88808e7de040 R09: ffffed1015d2707c
R10: ffffed1015d2707b R11: ffff8880ae9383db R12: ffff8880a689bc5e
R13: 1ffff920001b5153 R14: 0000000000000030 R15: ffffc90000da8af8
FS: 00007fd7a42be700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b32338000 CR3: 00000000a928c000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
hsr_handle_frame+0x1c5/0x630 net/hsr/hsr_slave.c:31
__netif_receive_skb_core+0xfbc/0x30b0 net/core/dev.c:5099
__netif_receive_skb_one_core+0xa8/0x1a0 net/core/dev.c:5196
__netif_receive_skb+0x2c/0x1d0 net/core/dev.c:5312
process_backlog+0x206/0x750 net/core/dev.c:6144
napi_poll net/core/dev.c:6582 [inline]
net_rx_action+0x508/0x1120 net/core/dev.c:6650
__do_softirq+0x262/0x98c kernel/softirq.c:292
do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1082
</IRQ>
Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's never used after introduced. So maybe better to remove.
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hsr_debugfs_rename prototype got an extra 'void' that needs to
be removed again:
In file included from /git/arm-soc/net/hsr/hsr_main.c:12:
net/hsr/hsr_main.h:194:20: error: two or more data types in declaration specifiers
static inline void void hsr_debugfs_rename(struct net_device *dev)
Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr slave interfaces don't have debugfs directory.
So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name
is changed.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
ip link set dummy0 name ap
Splat looks like:
[21071.899367][T22666] ap: renamed from dummy0
[21071.914005][T22666] ==================================================================
[21071.919008][T22666] BUG: KASAN: slab-out-of-bounds in hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.923640][T22666] Read of size 8 at addr ffff88805febcd98 by task ip/22666
[21071.926941][T22666]
[21071.927750][T22666] CPU: 0 PID: 22666 Comm: ip Not tainted 5.5.0-rc2+ #240
[21071.929919][T22666] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[21071.935094][T22666] Call Trace:
[21071.935867][T22666] dump_stack+0x96/0xdb
[21071.936687][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.937774][T22666] print_address_description.constprop.5+0x1be/0x360
[21071.939019][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940081][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940949][T22666] __kasan_report+0x12a/0x16f
[21071.941758][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.942674][T22666] kasan_report+0xe/0x20
[21071.943325][T22666] hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.944187][T22666] hsr_netdev_notify+0x1fe/0x9b0 [hsr]
[21071.945052][T22666] ? __module_text_address+0x13/0x140
[21071.945897][T22666] notifier_call_chain+0x90/0x160
[21071.946743][T22666] dev_change_name+0x419/0x840
[21071.947496][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.948600][T22666] ? netdev_adjacent_rename_links+0x280/0x280
[21071.949577][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.950672][T22666] ? lock_downgrade+0x6e0/0x6e0
[21071.951345][T22666] ? do_setlink+0x811/0x2ef0
[21071.951991][T22666] do_setlink+0x811/0x2ef0
[21071.952613][T22666] ? is_bpf_text_address+0x81/0xe0
[ ... ]
Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com
Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Splat looks like:
[ 236.066091][ T3286] list_add corruption. next->prev should be prev (ffff8880a5940300), but was ffff8880a5940d0.
[ 236.069617][ T3286] ------------[ cut here ]------------
[ 236.070545][ T3286] kernel BUG at lib/list_debug.c:25!
[ 236.071391][ T3286] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 236.072343][ T3286] CPU: 0 PID: 3286 Comm: arping Tainted: G W 5.5.0-rc1+ #209
[ 236.073463][ T3286] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 236.074695][ T3286] RIP: 0010:__list_add_valid+0x74/0xd0
[ 236.075499][ T3286] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 b
[ 236.078277][ T3286] RSP: 0018:ffff8880aaa97648 EFLAGS: 00010286
[ 236.086991][ T3286] RAX: 0000000000000075 RBX: ffff8880d4624c20 RCX: 0000000000000000
[ 236.088000][ T3286] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed1015552ebf
[ 236.098897][ T3286] RBP: ffff88809b53d200 R08: ffffed101b3c04f9 R09: ffffed101b3c04f9
[ 236.099960][ T3286] R10: 00000000308769a1 R11: ffffed101b3c04f8 R12: ffff8880d4624c28
[ 236.100974][ T3286] R13: ffff8880d4624c20 R14: 0000000040310100 R15: ffff8880ce17ee02
[ 236.138967][ T3286] FS: 00007f23479fa680(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 236.144852][ T3286] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 236.145720][ T3286] CR2: 00007f4a14bab210 CR3: 00000000a61c6001 CR4: 00000000000606f0
[ 236.146776][ T3286] Call Trace:
[ 236.147222][ T3286] hsr_add_node+0x314/0x490 [hsr]
[ 236.153633][ T3286] hsr_forward_skb+0x2b6/0x1bc0 [hsr]
[ 236.154362][ T3286] ? rcu_read_lock_sched_held+0x90/0xc0
[ 236.155091][ T3286] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 236.156607][ T3286] hsr_dev_xmit+0x70/0xd0 [hsr]
[ 236.157254][ T3286] dev_hard_start_xmit+0x160/0x740
[ 236.157941][ T3286] __dev_queue_xmit+0x1961/0x2e10
[ 236.158565][ T3286] ? netdev_core_pick_tx+0x2e0/0x2e0
[ ... ]
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: fc4ecaeebd26 ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hsr module is being removed, debugfs_remove() is called to remove
both debugfs directory and file.
When module is being removed, module state is changed to
MODULE_STATE_GOING then exit() is called.
At this moment, module couldn't be held so try_module_get()
will be failed.
debugfs's open() callback tries to hold the module if .owner is existing.
If it fails, warning message is printed.
CPU0 CPU1
delete_module()
try_stop_module()
hsr_exit() open() <-- WARNING
debugfs_remove()
In order to avoid the warning message, this patch makes hsr module does
not set .owner. Unsetting .owner is safe because these are protected by
inode_lock().
Test commands:
#SHELL1
ip link add dummy0 type dummy
ip link add dummy1 type dummy
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
modprobe -rv hsr
done
#SHELL2
while :
do
cat /sys/kernel/debug/hsr0/node_table
done
Splat looks like:
[ 101.223783][ T1271] ------------[ cut here ]------------
[ 101.230309][ T1271] debugfs file owner did not clean up at exit: node_table
[ 101.230380][ T1271] WARNING: CPU: 3 PID: 1271 at fs/debugfs/file.c:309 full_proxy_open+0x10f/0x650
[ 101.233153][ T1271] Modules linked in: hsr(-) dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_d]
[ 101.237112][ T1271] CPU: 3 PID: 1271 Comm: cat Tainted: G W 5.5.0-rc1+ #204
[ 101.238270][ T1271] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 101.240379][ T1271] RIP: 0010:full_proxy_open+0x10f/0x650
[ 101.241166][ T1271] Code: 48 c1 ea 03 80 3c 02 00 0f 85 c1 04 00 00 49 8b 3c 24 e8 04 86 7e ff 84 c0 75 2d 4c 8
[ 101.251985][ T1271] RSP: 0018:ffff8880ca22fa38 EFLAGS: 00010286
[ 101.273355][ T1271] RAX: dffffc0000000008 RBX: ffff8880cc6e6200 RCX: 0000000000000000
[ 101.274466][ T1271] RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffff8880c4dd5c14
[ 101.275581][ T1271] RBP: 0000000000000000 R08: fffffbfff2922f5d R09: 0000000000000000
[ 101.276733][ T1271] R10: 0000000000000001 R11: 0000000000000000 R12: ffffffffc0551bc0
[ 101.277853][ T1271] R13: ffff8880c4059a48 R14: ffff8880be50a5e0 R15: ffffffff941adaa0
[ 101.278956][ T1271] FS: 00007f8871cda540(0000) GS:ffff8880da800000(0000) knlGS:0000000000000000
[ 101.280216][ T1271] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 101.282832][ T1271] CR2: 00007f88717cfd10 CR3: 00000000b9440005 CR4: 00000000000606e0
[ 101.283974][ T1271] Call Trace:
[ 101.285328][ T1271] do_dentry_open+0x63c/0xf50
[ 101.286077][ T1271] ? open_proxy_open+0x270/0x270
[ 101.288271][ T1271] ? __x64_sys_fchdir+0x180/0x180
[ 101.288987][ T1271] ? inode_permission+0x65/0x390
[ 101.289682][ T1271] path_openat+0x701/0x2810
[ 101.290294][ T1271] ? path_lookupat+0x880/0x880
[ 101.290957][ T1271] ? check_chain_key+0x236/0x5d0
[ 101.291676][ T1271] ? __lock_acquire+0xdfe/0x3de0
[ 101.292358][ T1271] ? sched_clock+0x5/0x10
[ 101.292962][ T1271] ? sched_clock_cpu+0x18/0x170
[ 101.293644][ T1271] ? find_held_lock+0x39/0x1d0
[ 101.305616][ T1271] do_filp_open+0x17a/0x270
[ 101.306061][ T1271] ? may_open_dev+0xc0/0xc0
[ ... ]
Fixes: fc4ecaeebd26 ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_dev_xmit() calls hsr_port_get_hsr() to find master node and that would
return NULL if master node is not existing in the list.
But hsr_dev_xmit() doesn't check return pointer so a NULL dereference
could occur.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
hping3 192.168.100.2 -2 --flood &
modprobe -rv hsr
Splat looks like:
[ 217.351122][ T1635] kasan: CONFIG_KASAN_INLINE enabled
[ 217.352969][ T1635] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 217.354297][ T1635] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 217.355507][ T1635] CPU: 1 PID: 1635 Comm: hping3 Not tainted 5.4.0+ #192
[ 217.356472][ T1635] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 217.357804][ T1635] RIP: 0010:hsr_dev_xmit+0x34/0x90 [hsr]
[ 217.373010][ T1635] Code: 48 8d be 00 0c 00 00 be 04 00 00 00 48 83 ec 08 e8 21 be ff ff 48 8d 78 10 48 ba 00 b
[ 217.376919][ T1635] RSP: 0018:ffff8880cd8af058 EFLAGS: 00010202
[ 217.377571][ T1635] RAX: 0000000000000000 RBX: ffff8880acde6840 RCX: 0000000000000002
[ 217.379465][ T1635] RDX: dffffc0000000000 RSI: 0000000000000004 RDI: 0000000000000010
[ 217.380274][ T1635] RBP: ffff8880acde6840 R08: ffffed101b440d5d R09: 0000000000000001
[ 217.381078][ T1635] R10: 0000000000000001 R11: ffffed101b440d5c R12: ffff8880bffcc000
[ 217.382023][ T1635] R13: ffff8880bffcc088 R14: 0000000000000000 R15: ffff8880ca675c00
[ 217.383094][ T1635] FS: 00007f060d9d1740(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[ 217.384289][ T1635] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 217.385009][ T1635] CR2: 00007faf15381dd0 CR3: 00000000d523c001 CR4: 00000000000606e0
[ 217.385940][ T1635] Call Trace:
[ 217.386544][ T1635] dev_hard_start_xmit+0x160/0x740
[ 217.387114][ T1635] __dev_queue_xmit+0x1961/0x2e10
[ 217.388118][ T1635] ? check_object+0xaf/0x260
[ 217.391466][ T1635] ? __alloc_skb+0xb9/0x500
[ 217.392017][ T1635] ? init_object+0x6b/0x80
[ 217.392629][ T1635] ? netdev_core_pick_tx+0x2e0/0x2e0
[ 217.393175][ T1635] ? __alloc_skb+0xb9/0x500
[ 217.393727][ T1635] ? rcu_read_lock_sched_held+0x90/0xc0
[ 217.394331][ T1635] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 217.395013][ T1635] ? kasan_unpoison_shadow+0x30/0x40
[ 217.395668][ T1635] ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[ 217.396280][ T1635] ? __kmalloc_node_track_caller+0x3a8/0x3f0
[ 217.399007][ T1635] ? __kasan_kmalloc.constprop.4+0xa0/0xd0
[ 217.400093][ T1635] ? __kmalloc_reserve.isra.46+0x2e/0xb0
[ 217.401118][ T1635] ? memset+0x1f/0x40
[ 217.402529][ T1635] ? __alloc_skb+0x317/0x500
[ 217.404915][ T1635] ? arp_xmit+0xca/0x2c0
[ ... ]
Fixes: 311633b60406 ("hsr: switch ->dellink() to ->ndo_uninit()")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switching from ->priv_destructor to dellink() has an unexpected
consequence: existing RCU readers, that is, hsr_port_get_hsr()
callers, may still be able to read the port list.
Instead of checking the return value of each hsr_port_get_hsr(),
we can just move it to ->ndo_uninit() which is called after
device unregister and synchronize_net(), and we still have RTNL
lock there.
Fixes: b9a1e627405d ("hsr: implement dellink to clean up resources")
Fixes: edf070a0fb45 ("hsr: fix a NULL pointer deref in hsr_dev_xmit()")
Reported-by: syzbot+097ef84cdc95843fbaa8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_port_get_hsr() could return NULL and kernel
could crash:
BUG: kernel NULL pointer dereference, address: 0000000000000010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 8000000074b84067 P4D 8000000074b84067 PUD 7057d067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 0 PID: 754 Comm: a.out Not tainted 5.2.0-rc6+ #718
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
RIP: 0010:hsr_dev_xmit+0x20/0x31
Code: 48 8b 1b eb e0 5b 5d 41 5c c3 66 66 66 66 90 55 48 89 fd 48 8d be 40 0b 00 00 be 04 00 00 00 e8 ee f2 ff ff 48 89 ef 48 89 c6 <48> 8b 40 10 48 89 45 10 e8 6c 1b 00 00 31 c0 5d c3 66 66 66 66 90
RSP: 0018:ffffb5b400003c48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff9821b4509a88 RCX: 0000000000000000
RDX: ffff9821b4509a88 RSI: 0000000000000000 RDI: ffff9821bc3fc7c0
RBP: ffff9821bc3fc7c0 R08: 0000000000000000 R09: 00000000000c2019
R10: 0000000000000000 R11: 0000000000000002 R12: ffff9821bc3fc7c0
R13: ffff9821b4509a88 R14: 0000000000000000 R15: 000000000000006e
FS: 00007fee112a1800(0000) GS:ffff9821bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000006e9ce000 CR4: 00000000000406f0
Call Trace:
<IRQ>
netdev_start_xmit+0x1b/0x38
dev_hard_start_xmit+0x121/0x21e
? validate_xmit_skb.isra.0+0x19/0x1e3
__dev_queue_xmit+0x74c/0x823
? lockdep_hardirqs_on+0x12b/0x17d
ip6_finish_output2+0x3d3/0x42c
? ip6_mtu+0x55/0x5c
? mld_sendpack+0x191/0x229
mld_sendpack+0x191/0x229
mld_ifc_timer_expire+0x1f7/0x230
? mld_dad_timer_expire+0x58/0x58
call_timer_fn+0x12e/0x273
__run_timers.part.0+0x174/0x1b5
? mld_dad_timer_expire+0x58/0x58
? sched_clock_cpu+0x10/0xad
? mark_lock+0x26/0x1f2
? __lock_is_held+0x40/0x71
run_timer_softirq+0x26/0x48
__do_softirq+0x1af/0x392
irq_exit+0x53/0xa2
smp_apic_timer_interrupt+0x1c4/0x1d9
apic_timer_interrupt+0xf/0x20
</IRQ>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_link_ops implements ->newlink() but not ->dellink(),
which leads that resources not released after removing the device,
particularly the entries in self_node_db and node_db.
So add ->dellink() implementation to replace the priv_destructor.
This also makes the code slightly easier to understand.
Reported-by: syzbot+c6167ec3de7def23d1e8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hsr_del_port() should release all the resources allocated
in hsr_add_port().
As a consequence of this change, hsr_for_each_port() is no
longer safe to work with hsr_del_port(), switch to
list_for_each_entry_safe() as we always hold RTNL lock.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
