summaryrefslogtreecommitdiff
path: root/net/ipv6/esp6_offload.c
AgeCommit message (Collapse)Author
2017-09-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07esp: Fix error handling on layer 2 xmit.Steffen Klassert
esp_output_tail() and esp6_output_tail() can return negative and positive error values. We currently treat only negative values as errors, fix this to treat both cases as error. Fixes: fca11ebde3f0 ("esp4: Reorganize esp_output") Fixes: 383d0350f2cc ("esp6: Reorganize esp_output") Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-08-02xfrm: Auto-load xfrm offload modulesIlan Tayari
IPSec crypto offload depends on the protocol-specific offload module (such as esp_offload.ko). When the user installs an SA with crypto-offload, load the offload module automatically, in the same way that the protocol module is loaded (such as esp.ko) Signed-off-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-08-02esp6: Support RX checksum with crypto offloadIlan Tayari
Keep the device's reported ip_summed indication in case crypto was offloaded by the device. Subtract the csum values of the stripped parts (esp header+iv, esp trailer+auth_data) to keep value correct. Note: CHECKSUM_COMPLETE should be indicated only if skb->csum has the post-decryption offload csum value. Signed-off-by: Ariel Levkovich <lariel@mellanox.com> Signed-off-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-06-22esp6_offload: Fix IP6CB(skb)->nhoff for ESP GROYossi Kuperman
IP6CB(skb)->nhoff is the offset of the nexthdr field in an IPv6 header, unless there are extension headers present, in which case nhoff points to the nexthdr field of the last extension header. In non-GRO code path, nhoff is set by ipv6_rcv before any XFRM code is executed. Conversely, in GRO code path (when esp6_offload is loaded), nhoff is not set. The following functions fail to read the correct value and eventually the packet is dropped: xfrm6_transport_finish xfrm6_tunnel_input xfrm6_rcv_tnl Set nhoff to the proper offset of nexthdr in esp6_gro_receive. Fixes: 7785bba299a8 ("esp: Add a software GRO codepath") Signed-off-by: Yossi Kuperman <yossiku@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-04-19esp4/6: Fix GSO path for non-GSO SW-crypto packetsIlan Tayari
If esp*_offload module is loaded, outbound packets take the GSO code path, being encapsulated at layer 3, but encrypted in layer 2. validate_xmit_xfrm calls esp*_xmit for that. esp*_xmit was wrongfully detecting these packets as going through hardware crypto offload, while in fact they should be encrypted in software, causing plaintext leakage to the network, and also dropping at the receiver side. Perform the encryption in esp*_xmit, if the SA doesn't have a hardware offload_handle. Also, align esp6 code to esp4 logic. Fixes: fca11ebde3f0 ("esp4: Reorganize esp_output") Fixes: 383d0350f2cc ("esp6: Reorganize esp_output") Signed-off-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-04-19esp6: fix incorrect null pointer check on xoColin Ian King
The check for xo being null is incorrect, currently it is checking for non-null, it should be checking for null. Detected with CoverityScan, CID#1429349 ("Dereference after null check") Fixes: 7862b4058b9f ("esp: Add gso handlers for esp4 and esp6") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-04-14xfrm: Prepare the GRO codepath for hardware offloading.Steffen Klassert
On IPsec hardware offloading, we already get a secpath with valid state attached when the packet enters the GRO handlers. So check for hardware offload and skip the state lookup in this case. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-04-14esp: Add gso handlers for esp4 and esp6Steffen Klassert
This patch extends the xfrm_type by an encap function pointer and implements esp4_gso_encap and esp6_gso_encap. These functions doing the basic esp encapsulation for a GSO packet. In case the GSO packet needs to be segmented in software, we add gso_segment functions. This codepath is going to be used on esp hardware offloads. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-04-14esp6: Reorganize esp_outputSteffen Klassert
We need a fallback for ESP at layer 2, so split esp6_output into generic functions that can be used at layer 3 and layer 2 and use them in esp_output. We also add esp6_xmit which is used for the layer 2 fallback. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2017-02-15esp: Add a software GRO codepathSteffen Klassert
This patch adds GRO ifrastructure and callbacks for ESP on ipv4 and ipv6. In case the GRO layer detects an ESP packet, the esp{4,6}_gro_receive() function does a xfrm state lookup and calls the xfrm input layer if it finds a matching state. The packet will be decapsulated and reinjected it into layer 2. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>