| Age | Commit message (Collapse) | Author |
|---|
|
We currently have to adjust ipv6 route gc_thresh/max_size depending
on number of cpus on a server, this makes very little sense.
If the kernels sets /proc/sys/net/ipv6/route/gc_thresh to 1024
and /proc/sys/net/ipv6/route/max_size to 4096, then we better
not track the percpu dst that our implementation uses.
Only routes not added (directly or indirectly) by the admin
should be tracked and limited.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
percpu_counter_add() uses a default batch size which is quite big
on platforms with 256 cpus. (2*256 -> 512)
This means dst_entries_get_fast() can be off by +/- 2*(nr_cpus^2)
(131072 on servers with 256 cpus)
Reduce the batch size to something more reasonable, and
add logic to ip6_dst_gc() to call dst_entries_get_slow()
before calling the _very_ expensive fib6_run_gc() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Segment Routing Header (SRH) which defines the SRv6 dataplane is defined
in RFC8754.
RFC8754 (section 4.1) defines the SR source node behavior which encapsulates
packets into an outer IPv6 header and SRH. The SR source node encodes the
full list of Segments that defines the packet path in the SRH. Then, the
first segment from list of Segments is copied into the Destination address
of the outer IPv6 header and the packet is sent to the first hop in its path
towards the destination.
If the Segment list has only one segment, the SR source node can omit the SRH
as he only segment is added in the destination address.
RFC8754 (section 4.1.1) defines the Reduced SRH, when a source does not
require the entire SID list to be preserved in the SRH. A reduced SRH does
not contain the first segment of the related SR Policy (the first segment is
the one already in the DA of the IPv6 header), and the Last Entry field is
set to n-2, where n is the number of elements in the SR Policy.
RFC8754 (section 4.3.1.1) defines the SRH processing and the logic to
validate the SRH (S09, S10, S11) which works for both reduced and
non-reduced behaviors.
This patch updates seg6_validate_srh() to validate the SRH as per RFC8754.
Signed-off-by: Ahmed Abdelsalam <ahabdels@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-01 (v2)
The following pull-request contains BPF updates for your *net-next* tree.
We've added 61 non-merge commits during the last 6 day(s) which contain
a total of 153 files changed, 6739 insertions(+), 3367 deletions(-).
The main changes are:
1) pulled work.sysctl from vfs tree with sysctl bpf changes.
2) bpf_link observability, from Andrii.
3) BTF-defined map in map, from Andrii.
4) asan fixes for selftests, from Andrii.
5) Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH, from Jakub.
6) production cloudflare classifier as a selftes, from Lorenz.
7) bpf_ktime_get_*_ns() helper improvements, from Maciej.
8) unprivileged bpftool feature probe, from Quentin.
9) BPF_ENABLE_STATS command, from Song.
10) enable bpf_[gs]etsockopt() helpers for sock_ops progs, from Stanislav.
11) enable a bunch of common helpers for cg-device, sysctl, sockopt progs,
from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nik reported a bug with pcpu dst cache when nexthop objects are
used illustrated by the following:
$ ip netns add foo
$ ip -netns foo li set lo up
$ ip -netns foo addr add 2001:db8:11::1/128 dev lo
$ ip netns exec foo sysctl net.ipv6.conf.all.forwarding=1
$ ip li add veth1 type veth peer name veth2
$ ip li set veth1 up
$ ip addr add 2001:db8:10::1/64 dev veth1
$ ip li set dev veth2 netns foo
$ ip -netns foo li set veth2 up
$ ip -netns foo addr add 2001:db8:10::2/64 dev veth2
$ ip -6 nexthop add id 100 via 2001:db8:10::2 dev veth1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Create a pcpu entry on cpu 0:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
Re-add the route entry:
$ ip -6 ro del 2001:db8:11::1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Route get on cpu 0 returns the stale pcpu:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
RTNETLINK answers: Network is unreachable
While cpu 1 works:
$ taskset -a -c 1 ip -6 route get 2001:db8:11::1
2001:db8:11::1 from :: via 2001:db8:10::2 dev veth1 src 2001:db8:10::1 metric 1024 pref medium
Conversion of FIB entries to work with external nexthop objects
missed an important difference between IPv4 and IPv6 - how dst
entries are invalidated when the FIB changes. IPv4 has a per-network
namespace generation id (rt_genid) that is bumped on changes to the FIB.
Checking if a dst_entry is still valid means comparing rt_genid in the
rtable to the current value of rt_genid for the namespace.
IPv6 also has a per network namespace counter, fib6_sernum, but the
count is saved per fib6_node. With the per-node counter only dst_entries
based on fib entries under the node are invalidated when changes are
made to the routes - limiting the scope of invalidations. IPv6 uses a
reference in the rt6_info, 'from', to track the corresponding fib entry
used to create the dst_entry. When validating a dst_entry, the 'from'
is used to backtrack to the fib6_node and check the sernum of it to the
cookie passed to the dst_check operation.
With the inline format (nexthop definition inline with the fib6_info),
dst_entries cached in the fib6_nh have a 1:1 correlation between fib
entries, nexthop data and dst_entries. With external nexthops, IPv6
looks more like IPv4 which means multiple fib entries across disparate
fib6_nodes can all reference the same fib6_nh. That means validation
of dst_entries based on external nexthops needs to use the IPv4 format
- the per-network namespace counter.
Add sernum to rt6_info and set it when creating a pcpu dst entry. Update
rt6_get_cookie to return sernum if it is set and update dst_check for
IPv6 to look for sernum set and based the check on it if so. Finally,
rt6_get_pcpu_route needs to validate the cached entry before returning
a pcpu entry (similar to the rt_cache_valid calls in __mkroute_input and
__mkroute_output for IPv4).
This problem only affects routes using the new, external nexthops.
Thanks to the kbuild test robot for catching the IS_ENABLED needed
around rt_genid_ipv6 before I sent this out.
Fixes: 5b98324ebe29 ("ipv6: Allow routes to use nexthop objects")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no callers in-tree anymore since commit 84287bb32856 ("ila: add
checksum neutral map auto").
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not much to be done here:
- add SPDX header;
- add a document title;
- mark a literal as such, in order to avoid a warning;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull in Christoph Hellwig's series that changes the sysctl's ->proc_handler
methods to take kernel pointers instead. It gets rid of the set_fs address
space overrides used by BPF. As per discussion, pull in the feature branch
into bpf-next as it relates to BPF sysctl progs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200427071508.GV23230@ZenIV.linux.org.uk/T/
|
|
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Simple overlapping changes to linux/vermagic.h
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes it impossible that cmpri or cmpre values are set to the
value 16 which is not possible, because these are 4 bit values. We
currently run in an overflow when assigning the value 16 to it.
According to the standard a value of 16 can be interpreted as a full
elided address which isn't possible to set as compression value. A reason
why this cannot be set is that the current ipv6 header destination address
should never show up inside the segments of the rpl header. In this case we
run in a overflow and the address will have no compression at all. Means
cmpri or compre is set to 0.
As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value
inside the rpl header the current behaviour ends in an invalid header
format. This patch simple use the best compression method if we ever run
into the case that the destination address is showed up inside the rpl
segments. We avoid the overflow handling and the rpl header is still valid,
even when we have the destination address inside the rpl segments.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit fac6fce9bdb5 ("net: icmp6: provide input address for
traceroute6") ICMPv6 errors have source addresses from the ingress
interface. However, this overrides when source address selection is
influenced by setting preferred source addresses on routes.
This can result in ICMP errors being lost to upstream BCP38 filters
when the wrong source addresses are used, breaking path MTU discovery
and traceroute.
This patch sets the modified source address selection to only take place
when the route used has no prefsrc set.
It can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8::3 dev v1 nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip addr add 2001:db8:100::1 dev lo
ip netns exec test ip route add 2001:db8::1 dev v2 src 2001:db8:100::1
ip route add 2001:db8:1000::1 via 2001:db8::2
traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute6 -s 2001:db8::3 2001:db8:1000::1
ip netns delete test
Output before:
$ traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 0.843 ms !N 0.396 ms !N 0.257 ms !N
$ traceroute6 -s 2001:db8::3 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 0.772 ms !N 0.257 ms !N 0.357 ms !N
After:
$ traceroute6 -s 2001:db8::1 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8:100::1 (2001:db8:100::1) 8.885 ms !N 0.310 ms !N 0.174 ms !N
$ traceroute6 -s 2001:db8::3 2001:db8:1000::1
traceroute to 2001:db8:1000::1 (2001:db8:1000::1), 30 hops max, 80 byte packets
1 2001:db8::2 (2001:db8::2) 1.403 ms !N 0.205 ms !N 0.313 ms !N
Fixes: fac6fce9bdb5 ("net: icmp6: provide input address for traceroute6")
Signed-off-by: Tim Stallard <code@timstallard.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix the loop iteration by not walking over the last
iteration. The cmpri compressing value exempt the last segment. As the
code shows the last iteration will be overwritten by cmpre value
handling which is for the last segment.
I think this doesn't end in any bufferoverflows because we work on worst
case temporary buffer sizes but it ends in not best compression settings
in some cases.
Fixes: 8610c7c6e3bd ("net: ipv6: add support for rpl sr exthdr")
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we limited the retrans_time to be greater than HZ/2. i.e.
setting retrans_time less than 500ms will not work. This makes the user
unable to achieve a more accurate control for bonding arp fast failover.
Update the sanity check to HZ/100, which is 10ms, to let users have more
ability on the retrans_time control.
v3: sync the behavior with IPv6 and update all the timer handler
v2: use HZ instead of hard code number
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bonding slave and team port devices should not have link-local addresses
automatically added to them, as it can interfere with openvswitch being
able to properly add tc ingress.
Basic reproducer, courtesy of Marcelo:
$ ip link add name bond0 type bond
$ ip link set dev ens2f0np0 master bond0
$ ip link set dev ens2f1np2 master bond0
$ ip link set dev bond0 up
$ ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
11: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link
valid_lft forever preferred_lft forever
(above trimmed to relevant entries, obviously)
$ sysctl net.ipv6.conf.ens2f0np0.addr_gen_mode=0
net.ipv6.conf.ens2f0np0.addr_gen_mode = 0
$ sysctl net.ipv6.conf.ens2f1np2.addr_gen_mode=0
net.ipv6.conf.ens2f1np2.addr_gen_mode = 0
$ ip a l ens2f0np0
2: ens2f0np0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc
mq master bond0 state UP group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
$ ip a l ens2f1np2
5: ens2f1np2: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc
mq master bond0 state DOWN group default qlen 1000
link/ether 00:0f:53:2f:ea:40 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:53ff:fe2f:ea40/64 scope link tentative
valid_lft forever preferred_lft forever
Looks like addrconf_sysctl_addr_gen_mode() bypasses the original "is
this a slave interface?" check added by commit c2edacf80e15, and
results in an address getting added, while w/the proposed patch added,
no address gets added. This simply adds the same gating check to another
code path, and thus should prevent the same devices from erroneously
obtaining an ipv6 link-local address.
Fixes: d35a00b8e33d ("net/ipv6: allow sysctl to change link-local address generation mode")
Reported-by: Moshe Levi <moshele@mellanox.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case memory resources for buf were allocated, release them before
return.
Addresses-Coverity-ID: 1492011 ("Resource leak")
Fixes: a7a29f9c361f ("net: ipv6: add rpl sr tunnel")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the UDP/TCP handlers slightly to allow skb_steal_sock() to make
the determination of whether the socket is reference counted in the case
where it is prefetched by earlier logic such as early_demux.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200329225342.16317-3-joe@wand.net.nz
|
|
Add support for TPROXY via a new bpf helper, bpf_sk_assign().
This helper requires the BPF program to discover the socket via a call
to bpf_sk*_lookup_*(), then pass this socket to the new helper. The
helper takes its own reference to the socket in addition to any existing
reference that may or may not currently be obtained for the duration of
BPF processing. For the destination socket to receive the traffic, the
traffic must be routed towards that socket via local route. The
simplest example route is below, but in practice you may want to route
traffic more narrowly (eg by CIDR):
$ ip route add local default dev lo
This patch avoids trying to introduce an extra bit into the skb->sk, as
that would require more invasive changes to all code interacting with
the socket to ensure that the bit is handled correctly, such as all
error-handling cases along the path from the helper in BPF through to
the orphan path in the input. Instead, we opt to use the destructor
variable to switch on the prefetch of the socket.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200329225342.16317-2-joe@wand.net.nz
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-03-28
1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
in xfrm_state_alloc(). From Huang Zijiang.
2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
so share this function to avoide code duplcation.
From Raed Salem.
3) Add offload support for esp beet mode.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment conflict in mac80211.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2020-03-27
1) Handle NETDEV_UNREGISTER for xfrm device to handle asynchronous
unregister events cleanly. From Raed Salem.
2) Fix vti6 tunnel inter address family TX through bpf_redirect().
From Nicolas Dichtel.
3) Fix lenght check in verify_sec_ctx_len() to avoid a
slab-out-of-bounds. From Xin Long.
4) Add a missing verify_sec_ctx_len check in xfrm_add_acquire
to avoid a possible out-of-bounds to access. From Xin Long.
5) Use built-in RCU list checking of hlist_for_each_entry_rcu
to silence false lockdep warning in __xfrm6_tunnel_spi_lookup
when CONFIG_PROVE_RCU_LIST is enabled. From Madhuparna Bhowmik.
6) Fix a panic on esp offload when crypto is done asynchronously.
From Xin Long.
7) Fix a skb memory leak in an error path of vti6_rcv.
From Torsten Hilbrich.
8) Fix a race that can lead to a doulbe free in xfrm_policy_timer.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is trivial since we already have support for the entirely
identical (from the kernel's point of view) RDNSS, DNSSL, etc. that
also contain opaque data that needs to be passed down to userspace
for further processing.
As specified in draft-ietf-6man-ra-pref64-09 (while it is still a draft,
it is purely waiting on the RFC Editor for cleanups and publishing):
PREF64 option contains lifetime and a (up to) 96-bit IPv6 prefix.
The 8-bit identifier of the option type as assigned by the IANA is 38.
Since we lack DNS64/NAT64/CLAT support in kernel at the moment,
thus this option should also be passed on to userland.
See:
https://tools.ietf.org/html/draft-ietf-6man-ra-pref64-09
https://www.iana.org/assignments/icmpv6-parameters/icmpv6-parameters.xhtml#icmpv6-parameters-5
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to xfrm6_tunnel/transport_gso_segment(), _gso_segment()
is added to do gso_segment for esp6 beet mode. Before calling
inet6_offloads[proto]->callbacks.gso_segment, it needs to do:
- Get the upper proto from ph header to get its gso_segment
when xo->proto is IPPROTO_BEETPH.
- Add SKB_GSO_TCPV6 to gso_type if x->sel.family != AF_INET6
and the proto == IPPROTO_TCP, so that the current tcp ipv6
packet can be segmented.
- Calculate a right value for skb->transport_header and move
skb->data to the transport header position.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vti6_rcv function performs some tests on the retrieved tunnel
including checking the IP protocol, the XFRM input policy, the
source and destination address.
In all but one places the skb is released in the error case. When
the input policy check fails the network packet is leaked.
Using the same goto-label discard in this case to fix this problem.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces")
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Lastly, fix checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
in net/bridge/netfilter/ebtables.c
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Minor overlapping changes, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the various uses of fallthrough comments to fallthrough;
Done via script
Link: https://lore.kernel.org/lkml/b56602fcf79f849e733e7b521bb0e17895d390fa.1582230379.git.joe@perches.com/
And by hand:
net/ipv6/ip6_fib.c has a fallthrough comment outside of an #ifdef block
that causes gcc to emit a warning if converted in-place.
So move the new fallthrough; inside the containing #ifdef/#endif too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rafał found an issue that for non-Ethernet interface, if we down and up
frequently, the memory will be consumed slowly.
The reason is we add allnodes/allrouters addressed in multicast list in
ipv6_add_dev(). When link down, we call ipv6_mc_down(), store all multicast
addresses via mld_add_delrec(). But when link up, we don't call ipv6_mc_up()
for non-Ethernet interface to remove the addresses. This makes idev->mc_tomb
getting bigger and bigger. The call stack looks like:
addrconf_notify(NETDEV_REGISTER)
ipv6_add_dev
ipv6_dev_mc_inc(ff01::1)
ipv6_dev_mc_inc(ff02::1)
ipv6_dev_mc_inc(ff02::2)
addrconf_notify(NETDEV_UP)
addrconf_dev_config
/* Alas, we support only Ethernet autoconfiguration. */
return;
addrconf_notify(NETDEV_DOWN)
addrconf_ifdown
ipv6_mc_down
igmp6_group_dropped(ff02::2)
mld_add_delrec(ff02::2)
igmp6_group_dropped(ff02::1)
igmp6_group_dropped(ff01::1)
After investigating, I can't found a rule to disable multicast on
non-Ethernet interface. In RFC2460, the link could be Ethernet, PPP, ATM,
tunnels, etc. In IPv4, it doesn't check the dev type when calls ip_mc_up()
in inetdev_event(). Even for IPv6, we don't check the dev type and call
ipv6_add_dev(), ipv6_dev_mc_inc() after register device.
So I think it's OK to fix this memory consumer by calling ipv6_mc_up() for
non-Ethernet interface.
v2: Also check IFF_MULTICAST flag to make sure the interface supports
multicast
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Fixes: 74235a25c673 ("[IPV6] addrconf: Fix IPv6 on tuntap tunnels")
Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when set link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data pointers of ipv6 sysctl are set one by one which is hard to
maintain, especially with kconfig. This patch simplifies it by using
math to point the per net sysctls into the appropriate struct net,
just like what we did for ipv4.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium
This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we modify the route metric, the peer address's route need also
be updated. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium
Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we add peer address with metric configured, IPv4 could set the dest
metric correctly, but IPv6 do not. e.g.
]# ip addr add 192.0.2.1 peer 192.0.2.2/32 dev eth1 metric 20
]# ip route show dev eth1
192.0.2.2 proto kernel scope link src 192.0.2.1 metric 20
]# ip addr add 2001:db8::1 peer 2001:db8::2/128 dev eth1 metric 20
]# ip -6 route show dev eth1
2001:db8::1 proto kernel metric 20 pref medium
2001:db8::2 proto kernel metric 256 pref medium
Fix this by using configured metric instead of default one.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes")
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
