summaryrefslogtreecommitdiff
path: root/net/mac80211/sta_info.h
AgeCommit message (Collapse)Author
2017-06-08mac80211: manage RX BA session offload without SKB queueJohannes Berg
Instead of using the SKB queue with the fake pkt_type for the offloaded RX BA session management, also handle this with the normal aggregation state machine worker. This also makes the use of this more reliable since it gets rid of the allocation of the fake skb. Combined with the previous patch, this finally allows us to get rid of the pkt_type hack entirely, so do that as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-08Merge remote-tracking branch 'net-next/master' into mac80211-nextJohannes Berg
This brings in commit 7a7c0a6438b8 ("mac80211: fix TX aggregation start/stop callback race") to allow the follow-up cleanup. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-30mac80211: fix TX aggregation start/stop callback raceJohannes Berg
When starting or stopping an aggregation session, one of the steps is that the driver calls back to mac80211 that the start/stop can proceed. This is handled by queueing up a fake SKB and processing it from the normal iface/sdata work. Since this isn't flushed when disassociating, the following race is possible: * associate * start aggregation session * driver callback * disassociate * associate again to the same AP * callback processing runs, leading to a WARN_ON() that the TID hadn't requested aggregation If the second association isn't to the same AP, there would only be a message printed ("Could not find station: <addr>"), but the same race could happen. Fix this by not going the whole detour with a fake SKB etc. but simply looking up the aggregation session in the driver callback, marking it with a START_CB/STOP_CB bit and then scheduling the regular aggregation work that will now process these bits as well. This also simplifies the code and gets rid of the whole problem with allocation failures of said skb, which could have left the session in limbo. Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-17mac80211: Dynamically set CoDel parameters per stationToke Høiland-Jørgensen
CoDel can be too aggressive if a station sends at a very low rate, leading reduced throughput. This gets worse the more stations are present, as each station gets more bursty the longer the round-robin scheduling between stations takes. This adds dynamic adjustment of CoDel parameters per station. It uses the rate selection information to estimate throughput and sets more lenient CoDel parameters if the estimated throughput is below a threshold (modified by the number of active stations). A new callback is added that drivers can use to notify mac80211 about changes in expected throughput, so the same adjustment can be made for cards that implement rate control in firmware. Drivers that don't use this will just get the default parameters. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> [remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove inline annotation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: use bitfield macros for encoded rateJohannes Berg
Instead of hand-coding the bit manipulations, use the bitfield macros to generate the code for the encoded bitrate. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: rename ieee80211_rx_status::vht_nss to just nssJohannes Berg
This field will need to be used again for HE, so rename it now. Again, mostly done with this spatch: @@ expression status; @@ -status->vht_nss +status->nss @@ expression status; @@ -status.vht_nss +status.nss Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: encode rate type (legacy, HT, VHT) with fewer bitsJohannes Berg
We don't really need three different bits for each, since the types are mutually exclusive. Use just two bits for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06mac80211: use DECLARE_EWMA for mesh_fail_avgManoharan, Rajkumar
As moving average is not considering fractional part, it will get stuck at the same level after certain state. For example, with current values, it can get stuck at 96. Fortunately the current threshold 95%, but if it were increased to 96 or more mesh paths would never be deactivated. Fix failure average movement by using EWMA helpers, which does take into account fractional parts. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> [johannes: pick a larger EWMA factor for more precision with the limited range that we will feed into it, adjust to new API] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-02average: change to declare precision, not factorJohannes Berg
Declaring the factor is counter-intuitive, and people are prone to using small(-ish) values even when that makes no sense. Change the DECLARE_EWMA() macro to take the fractional precision, in bits, rather than a factor, and update all users. While at it, add some more documentation. Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-02-27mac80211: don't reorder frames with SN smaller than SSNSara Sharon
When RX aggregation starts, transmitter may continue send frames with SN smaller than SSN until the AddBA response is received. However, the reorder buffer is already initialized at this point, which will cause the drop of such frames as duplicates since the head SN of the reorder buffer is set to the SSN, which is bigger. Cc: stable@vger.kernel.org Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-19mac80211: fix tid_agg_rx NULL dereferenceJohannes Berg
On drivers setting the SUPPORTS_REORDERING_BUFFER hardware flag, we crash when the peer sends an AddBA request while we already have a session open on the seame TID; this is because on those drivers, the tid_agg_rx is left NULL even though the session is valid, and the agg_session_valid bit is set. To fix this, store the dialog tokens outside the tid_agg_rx to be able to compare them to the received AddBA request. Fixes: f89e07d4cf26 ("mac80211: agg-rx: refuse ADDBA Request with timeout update") Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-20mac80211: Use rhltable instead of rhashtableHerbert Xu
mac80211 currently uses rhashtable with insecure_elasticity set to true. The latter is because of duplicate objects. What's more, mac80211 walks the rhashtable chains by hand which is broken as rhashtable may contain multiple tables due to resizing or rehashing. This patch fixes it by converting it to the newly added rhltable interface which is designed for use with duplicate objects. With rhltable a lookup returns a list of objects instead of a single one. This is then fed into the existing for_each_sta_info macro. This patch also deletes the sta_addr_hash function since rhashtable defaults to jhash. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-12mac80211: send delBA on unexpected BlockAck data framesJohannes Berg
When we receive data frames with ACK policy BlockAck, send delBA as requested by the 802.11 spec. Since this would be happening for every frame inside an A-MPDU if it's really received outside a session, limit it to a single attempt. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-08-11mac80211: mesh: Add support for HW RC implementationMaxim Altshul
Mesh HWMP module will be able to rely on the HW RC algorithm if it exists, for path metric calculations. This allows the metric calculation mechanism to calculate a correct metric, based on PER and last TX rate both via HW RC algorithm if it exists or via parameters collected by the SW. Signed-off-by: Maxim Altshul <maxim.altshul@ti.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-05-31mac80211: fix fast_tx header alignmentFelix Fietkau
The header field is defined as u8[] but also accessed as struct ieee80211_hdr. Enforce an alignment of 2 to prevent unnecessary unaligned accesses, which can be very harmful for performance on many platforms. Fixes: e495c24731a2 ("mac80211: extend fast-xmit for more ciphers") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2016-04-06mac80211: enable collecting station statistics per-CPUJohannes Berg
If the driver advertises the new HW flag USE_RSS, make the station statistics on the fast-rx path per-CPU. This will enable calling the RX in parallel, only hitting locking or shared cachelines when the fast-RX path isn't available. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: add fast-rx pathJohannes Berg
The regular RX path has a lot of code, but with a few assumptions on the hardware it's possible to reduce the amount of code significantly. Currently the assumptions on the driver are the following: * hardware/driver reordering buffer (if supporting aggregation) * hardware/driver decryption & PN checking (if using encryption) * hardware/driver did de-duplication * hardware/driver did A-MSDU deaggregation * AP_LINK_PS is used (in AP mode) * no client powersave handling in mac80211 (in client mode) of which some are actually checked per packet: * de-duplication * PN checking * decryption and additionally packets must * not be A-MSDU (have been deaggregated by driver/device) * be data packets * not be fragmented * be unicast * have RFC 1042 header Additionally dynamically we assume: * no encryption or CCMP/GCMP, TKIP/WEP/other not allowed * station must be authorized * 4-addr format not enabled Some data needed for the RX path is cached in a new per-station "fast_rx" structure, so that we only need to look at this and the packet, no other memory when processing packets on the fast RX path. After doing the above per-packet checks, the data path collapses down to a pretty simple conversion function taking advantage of the data cached in the small fast_rx struct. This should speed up the RX processing, and will make it easier to reason about parallelizing RX (for which statistics will need to be per-CPU still.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: fix RX u64 stats consistency on 32-bit platformsJohannes Berg
On 32-bit platforms, the 64-bit counters we keep need to be protected to be consistently read. Use the u64_stats_sync mechanism to do that. In order to not end up with overly long lines, refactor the tidstats assignments a bit. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: fix last RX rate data consistencyJohannes Berg
When storing the last_rate_* values in the RX code, there's nothing to guarantee consistency, so a concurrent reader could see, e.g. last_rate_idx on the new value, but last_rate_flag still on the old, getting completely bogus values in the end. To fix this, I lifted the sta_stats_encode_rate() function from my old rate statistics code, which encodes the entire rate data into a single 16-bit value, avoiding the consistency issue. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: add separate last_ack variableJohannes Berg
Instead of touching the rx_stats.last_rx from the status path, introduce and use a status_stats.last_ack variable. This will make rx_stats.last_rx indicate when the last frame was received, making it available for real "last_rx" and statistics gathering; statistics, when done per-CPU, will need to figure out which place was updated last for those items where the "last" value is exposed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: move averaged values out of rx_statsJohannes Berg
Move the averaged values out of rx_stats and into rx_stats_avg, to cleanly split them out. The averaged ones cannot be supported for parallel RX in a per-CPU fashion, while the other values can be collected per CPU and then combined/selected when needed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: clean up station flags debugfsJohannes Berg
Avoid the really strange %s%s%s expression, use an array of flag names and check that all flags are present. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: remove sta_info debugfs sub-structJohannes Berg
Since the previous patch, the struct only has a single member, so remove the struct and leave just the single member. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: Remove unused variable in per STA debugfs structMohammed Shafi Shajakhan
Remove unused variable in per STA debugfs structure, 'commit 34e895075e21 ("mac80211: allow station add/remove to sleep")' removed the only user of 'add_has_run'. Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: remove description of dropped memberLuis de Bethencourt
Commit 976bd9efdae6 ("mac80211: move beacon_loss_count into ifmgd") removed the member from the sta_info struct but the description stayed lingering. Remove it. Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: add API to allow filtering frames in BA sessionsSara Sharon
If any frames are dropped that are part of a BA session, the reorder buffer will "indefinitely" (until the timeout) wait for them to come in (or a BAR moving the window) and won't release frames after them. This means it isn't possible to filter frames within a BA session in firmware. Introduce an API function that allows such filtering. Calling this function will move the BA window forward to the new SSN, and allows marking frames after the SSN as having been filtered, so any future reordering activity will release frames while skipping the holes. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: support hw managing reorder logicSara Sharon
Enable driver to manage the reordering logic itself. This is needed for example for the iwlwifi driver that will support hardware assisted reordering. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: add atomic uploaded keys iteratorEliad Peller
add ieee80211_iter_keys_rcu() to iterate over uploaded keys in atomic context (when rcu is locked) The station removal code removes the keys only after calling synchronize_net(), so it's not safe to iterate the keys at this point (and postponing the actual key deletion with call_rcu() might result in some badly-ordered ops calls). Add a flag to indicate a station is being removed, and skip the configured keys if it's set. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-21mac80211: move station statistics into sub-structsJohannes Berg
Group station statistics by where they're (mostly) updated (TX, RX and TX-status) and group them into sub-structs of the struct sta_info. Also rename the variables since the grouping now makes it obvious where they belong. This makes it easier to identify where the statistics are updated in the code, and thus easier to think about them. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-21mac80211: move beacon_loss_count into ifmgdJohannes Berg
There's little point in keeping (and even sending to userspace) the beacon_loss_count value per station, since it can only apply to the AP on a managed-mode connection. Move the value to ifmgd, advertise it only in managed mode, and remove it from ethtool as it's available through better interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-21mac80211: remove sta->last_ack_signalJohannes Berg
This file only feeds a debugfs file that isn't very useful, so remove it. If necessary, we can add other ways to get this information, for example in the NL80211_CMD_PROBE_CLIENT response. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-14mac80211: move sta_set_rate_info_rx() and make it staticJohannes Berg
There's only a single caller of this function, so it can be moved to the same file and made static. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-09-22mac80211: allow to transmit A-MSDU within A-MPDUEmmanuel Grumbach
Advertise the capability to send A-MSDU within A-MPDU in the AddBA request sent by mac80211. Let the driver know about the peer's capabilities. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-08-14mac80211: use DECLARE_EWMAJohannes Berg
Instead of using the out-of-line average calculation, use the new DECLARE_EWMA() macro to declare a signal EWMA, and use that. This actually *reduces* the code size slightly (on x86-64) while also reducing the station info size by 80 bytes. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: mesh: separate plid and aid conceptsBob Copeland
According to 802.11-2012 13.3.1, a mesh STA should assign an AID upon receipt of a mesh peering open frame rather than using the link id of the peer. Using the peer link id has two potential issues: it may not be unique among the peers, and by its nature it is random, so the TIM may not compress well. In preparation for allocating it properly, use sta->sta.aid, but keep the existing behavior of using the plid in the aid we send. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: mesh: move fail_avg into mesh structJohannes Berg
This value is only used in mesh, so move it into the new mesh sub-struct of the station info. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: upgrade BW of TDLS peers when possibleArik Nemtsov
Define a station chandef, to be used for wider-bw TDLS peers. When both peers support the feature, upgrade the channel bandwidth to the maximum allowed by both peers and regulatory. Currently widths up to 80MHz are supported in the 5GHz band. When a TDLS peer connects/disconnects recalculate the channel type of the current chanctx. Make the chanctx width calculation consider wider-bw TDLS peers and similarly fix the max_required_bw calculation for the chanctx min_def. Since the sta->bandwidth is calculated only later on, take bss_conf.chandef.width as the minimal width for station interface. Set the upgraded channel width in the VHT-operation set during TDLS setup. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: define TDLS wider BW support bitsArik Nemtsov
Allow a device to specify support for the TDLS wider-bandwidth feature. Indicate this support during TDLS setup in the ext-capab IE and set an appropriate station flag when our TDLS peer supports it. This feature gives TDLS peers the ability to use a wider channel than the base width of the BSS. For instance VHT capable TDLS peers connected on a 20MHz channel can extend the channel to 80MHz, if regulatory considerations allow it. Do not cap the bandwidth of such stations by the current BSS channel width in mac80211. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: move mesh related station fields to own structJohannes Berg
There are now a fairly large number of mesh fields that really aren't needed in any other modes; move those into their own structure and allocate them separately. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: duplicate station's MAC address for hash tableJohannes Berg
Currently, the station hash table lookup (or iteration) must access two cachelines for each station - the one with the hash table node, and the one with the MAC address. Duplicate the MAC address next to the hash node to get rid of this. Since the MAC address is static there's no consistency problem introduced by this. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: fix comment referring to RX queueJohannes Berg
There are no RX queues in mac80211 (yet), the comment should refer to the TID (including one slot for non-QoS) rather than 'RX queue'. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-07-17mac80211: remove sta_info.gtk_idxJohannes Berg
This struct member is only assigned, never used otherwise; remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-09mac80211: Always check rates and capabilities in mesh modeAlexis Green
In mesh mode there is a race between establishing links and processing rates and capabilities in beacons. This is very noticeable with slow beacons (e.g. beacon intervals of 1s) and manifested for us as stations using minstrel when minstrel_ht should be used. Fixed by changing mesh_sta_info_init so that it always checks rates and such if it has not already done so. Signed-off-by: Alexis Green <agreen@cococorp.com> CC: Jesse Jones <jjones@cococorp.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-05-06mac80211: add missing documentation for rate_ctrl_lockJohannes Berg
This was missed in the previous patch, add some documentation for rate_ctrl_lock to avoid docbook warnings. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-05-05mac80211: remove sta->tx_fragments counterJohannes Berg
This counter is unsafe with concurrent TX and is only exposed through debugfs and ethtool. Instead of trying to fix it just remove it for now, if it's really needed then it should be exposed through nl80211 and in a way that drivers that do the fragmentation in the device could support it as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-04-22mac80211: extend fast-xmit for more ciphersJohannes Berg
When crypto is offloaded then in some cases it's all handled by the device, and in others only some space for the IV must be reserved in the frame. Handle both of these cases in the fast-xmit path, up to a limit of 18 bytes of space for IVs. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-04-22mac80211: add TX fastpathJohannes Berg
In order to speed up mac80211's TX path, add the "fast-xmit" cache that will cache the data frame 802.11 header and other data to be able to build the frame more quickly. This cache is rebuilt when external triggers imply changes, but a lot of the checks done per packet today are simplified away to the check for the cache. There's also a more detailed description in the code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>