summaryrefslogtreecommitdiff
path: root/net/ncsi
AgeCommit message (Collapse)Author
2021-07-08net/ncsi: add dummy response handler for Intel boardsIvan Mikhaylov
Add the dummy response handler for Intel boards to prevent incorrect handling of OEM commands. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-08net/ncsi: add NCSI Intel OEM command to keep PHY upIvan Mikhaylov
This allows to keep PHY link up and prevents any channel resets during the host load. It is KEEP_PHY_LINK_UP option(Veto bit) in i210 datasheet which block PHY reset and power state changes. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-08net/ncsi: fix restricted cast warning of sparseIvan Mikhaylov
Sparse reports: net/ncsi/ncsi-rsp.c:406:24: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:732:33: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:756:25: warning: cast to restricted __be32 net/ncsi/ncsi-manage.c:779:25: warning: cast to restricted __be32 Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-07net/ncsi: Fix spelling mistakesZheng Yongjun
Fix some spelling mistakes in comments: constuct ==> construct chanels ==> channels Detination ==> Destination Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Conflicts: MAINTAINERS - keep Chandrasekar drivers/net/ethernet/mellanox/mlx5/core/en_main.c - simple fix + trust the code re-added to param.c in -next is fine include/linux/bpf.h - trivial include/linux/ethtool.h - trivial, fix kdoc while at it include/linux/skmsg.h - move to relevant place in tcp.c, comment re-wrapped net/core/skmsg.c - add the sk = sk // sk = NULL around calls net/tipc/crypto.c - trivial Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-03-30net/ncsi: Avoid channel_monitor hrtimer deadlockMilton Miller
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed deadlock on SMP because stop calls del_timer_sync on the timer that invoked channel_monitor as its timer function. Recognise the inherent race of marking the monitor disabled before deleting the timer by just returning if enable was cleared. After a timeout (the default case -- reset to START when response received) just mark the monitor.enabled false. If the channel has an entry on the channel_queue list, or if the state is not ACTIVE or INACTIVE, then warn and mark the timer stopped and don't restart, as the locking is broken somehow. Fixes: 0795fb2021f0 ("net/ncsi: Stop monitor if channel times out or is inactive") Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-28ncsi: internal.h: Fix a spelloBhaskar Chowdhury
s/Firware/Firmware/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-12-23net/ncsi: Use real net-device for response handlerJohn Wang
When aggregating ncsi interfaces and dedicated interfaces to bond interfaces, the ncsi response handler will use the wrong net device to find ncsi_dev, so that the ncsi interface will not work properly. Here, we use the original net device to fix it. Fixes: 138635cc27c9 ("net/ncsi: NCSI response packet handler") Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com> Link: https://lore.kernel.org/r/20201223055523.2069-1-wangzhiqiang.bj@bytedance.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-12net/ncsi: Fix netlink registrationJoel Stanley
If a user unbinds and re-binds a NC-SI aware driver the kernel will attempt to register the netlink interface at runtime. The structure is marked __ro_after_init so registration fails spectacularly at this point. # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip ftgmac100 1e660000.ethernet: Using NCSI interface 8<--- cut here --- Unable to handle kernel paging request at virtual address 80a8f858 pgd = 8c768dd6 [80a8f858] *pgd=80a0841e(bad) Internal error: Oops: 80d [#1] SMP ARM CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51 Hardware name: Generic DT based system PC is at genl_register_family+0x1f8/0x6d4 LR is at 0xff26ffff pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153 sp : 8553bc80 ip : 81406244 fp : 8553bd04 r10: 8085d12c r9 : 80a8f73c r8 : 85739000 r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858 r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017 Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 85524008 DAC: 00000051 Process sh (pid: 116, stack limit = 0x1f1988d6) ... Backtrace: [<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48) r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000 r4:8121c000 [<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210) r5:8121c400 r4:8121c000 [<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778) r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88 r4:85739000 [<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8) r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000 [<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514) r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10 Jakub pointed out that ncsi_register_dev is obviously broken, because there is only one family so it would never work if there was more than one ncsi netdev. Fix the crash by registering the netlink family once on boot, and drop the code to unregister it. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-02genetlink: move to smaller ops wherever possibleJakub Kicinski
Bulk of the genetlink users can use smaller ops, move them. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-07-23net/ncsi: use eth_zero_addr() to clear mac addressMiaohe Lin
Use eth_zero_addr() to clear mac address insetad of memset(). Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-01-09net/ncsi: Support for multi host mellanox cardVijay Khemka
Multi host Mellanox cards require MAC affinity to be set before receiving any config commands. All config commands should also have unicast address for source address in command header. Adding GMA and SMAF(Set Mac Affinity) for Mellanox card and call these in channel probe state machine if it is defined in device tree. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-08net/ncsi: Send device address as source addressVijay Khemka
After receiving device mac address from device, send this as a source address for further commands instead of broadcast address. This will help in multi host NIC cards. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-30net/ncsi: Fix gma flag setting after responseVijay Khemka
gma_flag was set at the time of GMA command request but it should only be set after getting successful response. Movinng this flag setting in GMA response handler. This flag is used mainly for not repeating GMA command once received MAC address. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-19net/ncsi: Disable global multicast filterVijay Khemka
Disabling multicast filtering from NCSI if it is supported. As it should not filter any multicast packets. In current code, multicast filter is enabled and with an exception of optional field supported by device are disabled filtering. Mainly I see if goal is to disable filtering for IPV6 packets then let it disabled for every other types as well. As we are seeing issues with LLDP not working with this enabled filtering. And there are other issues with IPV6. By Disabling this multicast completely, it is working for both IPV6 as well as LLDP. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-08-31net/ncsi: add response handlers for PLDM over NC-SIBen Wei
This patch adds handlers for PLDM over NC-SI command response. This enables NC-SI driver recognizes the packet type so the responses don't get dropped as unknown packet type. PLDM over NC-SI are not handled in kernel driver for now, but can be passed back to user space via Netlink for further handling. Signed-off-by: Ben Wei <benwei@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Minor conflict in r8169, bug fix had two versions in net and net-next, take the net-next hunks. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22net/ncsi: update response packet length for GCPS/GNS/GNPTS commandsBen Wei
Update response packet length for the following commands per NC-SI spec - Get Controller Packet Statistics - Get NC-SI Statistics - Get NC-SI Pass-through Statistics command Signed-off-by: Ben Wei <benwei@fb.com> Reviewed-by: Justin Lee <justin.lee1@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22net/ncsi: Fix the payload copying for the request coming from NetlinkJustin.Lee1@Dell.com
The request coming from Netlink should use the OEM generic handler. The standard command handler expects payload in bytes/words/dwords but the actual payload is stored in data if the request is coming from Netlink. Signed-off-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-20net/ncsi: Ensure 32-bit boundary for data cksumTerry S. Duncan
The NCSI spec indicates that if the data does not end on a 32 bit boundary, one to three padding bytes equal to 0x00 shall be present to align the checksum field to a 32-bit boundary. Signed-off-by: Terry S. Duncan <terry.s.duncan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27genetlink: optionally validate strictly/dumpsJohannes Berg
Add options to strictly validate messages and dump messages, sometimes perhaps validating dump messages non-strictly may be required, so add an option for that as well. Since none of this can really be applied to existing commands, set the options everwhere using the following spatch: @@ identifier ops; expression X; @@ struct genl_ops ops[] = { ..., { .cmd = X, + .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP, ... }, ... }; For new commands one should just not copy the .validate 'opt-out' flags and thus get strict validation. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27netlink: make validation more configurable for future strictnessJohannes Berg
We currently have two levels of strict validation: 1) liberal (default) - undefined (type >= max) & NLA_UNSPEC attributes accepted - attribute length >= expected accepted - garbage at end of message accepted 2) strict (opt-in) - NLA_UNSPEC attributes accepted - attribute length >= expected accepted Split out parsing strictness into four different options: * TRAILING - check that there's no trailing data after parsing attributes (in message or nested) * MAXTYPE - reject attrs > max known type * UNSPEC - reject attributes with NLA_UNSPEC policy entries * STRICT_ATTRS - strictly validate attribute size The default for future things should be *everything*. The current *_strict() is a combination of TRAILING and MAXTYPE, and is renamed to _deprecated_strict(). The current regular parsing has none of this, and is renamed to *_parse_deprecated(). Additionally it allows us to selectively set one of the new flags even on old policies. Notably, the UNSPEC flag could be useful in this case, since it can be arranged (by filling in the policy) to not be an incompatible userspace ABI change, but would then going forward prevent forgetting attribute entries. Similar can apply to the POLICY flag. We end up with the following renames: * nla_parse -> nla_parse_deprecated * nla_parse_strict -> nla_parse_deprecated_strict * nlmsg_parse -> nlmsg_parse_deprecated * nlmsg_parse_strict -> nlmsg_parse_deprecated_strict * nla_parse_nested -> nla_parse_nested_deprecated * nla_validate_nested -> nla_validate_nested_deprecated Using spatch, of course: @@ expression TB, MAX, HEAD, LEN, POL, EXT; @@ -nla_parse(TB, MAX, HEAD, LEN, POL, EXT) +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression TB, MAX, NLA, POL, EXT; @@ -nla_parse_nested(TB, MAX, NLA, POL, EXT) +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT) @@ expression START, MAX, POL, EXT; @@ -nla_validate_nested(START, MAX, POL, EXT) +nla_validate_nested_deprecated(START, MAX, POL, EXT) @@ expression NLH, HDRLEN, MAX, POL, EXT; @@ -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT) +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT) For this patch, don't actually add the strict, non-renamed versions yet so that it breaks compile if I get it wrong. Also, while at it, make nla_validate and nla_parse go down to a common __nla_validate_parse() function to avoid code duplication. Ultimately, this allows us to have very strict validation for every new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the next patch, while existing things will continue to work as is. In effect then, this adds fully strict validation for any new command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27netlink: make nla_nest_start() add NLA_F_NESTED flagMichal Kubecek
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most netlink based interfaces (including recently added ones) are still not setting it in kernel generated messages. Without the flag, message parsers not aware of attribute semantics (e.g. wireshark dissector or libmnl's mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display the structure of their contents. Unfortunately we cannot just add the flag everywhere as there may be userspace applications which check nlattr::nla_type directly rather than through a helper masking out the flags. Therefore the patch renames nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start() as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually are rewritten to use nla_nest_start(). Except for changes in include/net/netlink.h, the patch was generated using this semantic patch: @@ expression E1, E2; @@ -nla_nest_start(E1, E2) +nla_nest_start_noflag(E1, E2) @@ expression E1, E2; @@ -nla_nest_start_noflag(E1, E2 | NLA_F_NESTED) +nla_nest_start(E1, E2) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Two easy cases of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-23net/ncsi: handle overflow when incrementing mac addressTao Ren
Previously BMC's MAC address is calculated by simply adding 1 to the last byte of network controller's MAC address, and it produces incorrect result when network controller's MAC address ends with 0xFF. The problem can be fixed by calling eth_addr_inc() function to increment MAC address; besides, the MAC address is also validated before assigning to BMC. Fixes: cb10c7c0dfd9 ("net/ncsi: Add NCSI Broadcom OEM command") Signed-off-by: Tao Ren <taoren@fb.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-22genetlink: make policy common to familyJohannes Berg
Since maxattr is common, the policy can't really differ sanely, so make it common as well. The only user that did in fact manage to make a non-common policy is taskstats, which has to be really careful about it (since it's still using a common maxattr!). This is no longer supported, but we can fake it using pre_doit. This reduces the size of e.g. nl80211.o (which has lots of commands): text data bss dec hex filename 398745 14323 2240 415308 6564c net/wireless/nl80211.o (before) 397913 14331 2240 414484 65314 net/wireless/nl80211.o (after) -------------------------------- -832 +8 0 -824 Which is obviously just 8 bytes for each command, and an added 8 bytes for the new policy pointer. I'm not sure why the ops list is counted as .text though. Most of the code transformations were done using the following spatch: @ops@ identifier OPS; expression POLICY; @@ struct genl_ops OPS[] = { ..., { - .policy = POLICY, }, ... }; @@ identifier ops.OPS; expression ops.POLICY; identifier fam; expression M; @@ struct genl_family fam = { .ops = OPS, .maxattr = M, + .policy = POLICY, ... }; This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing the cb->data as ops, which we want to change in a later genl patch. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-16net: ncsi: fix a missing check for nla_nest_startKangjie Lu
nla_nest_start may fail and thus deserves a check. The fix returns -EMSGSIZE in case it fails. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-27net/ncsi: Add NCSI Mellanox OEM commandVijay Khemka
This patch adds OEM Mellanox commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for getting mac address. ncsi_rsp_handler_oem_mlx: This handles response received for all mellanox OEM commands. ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Configure multi-package, multi-channel modes with failoverSamuel Mendoza-Jonas
This patch extends the ncsi-netlink interface with two new commands and three new attributes to configure multiple packages and/or channels at once, and configure specific failover modes. NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist of packages or channels allowed to be configured with the NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes respectively. If one of these whitelists is set only packages or channels matching the whitelist are considered for the channel queue in ncsi_choose_active_channel(). These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that multiple packages or channels may be configured simultaneously. NCSI hardware arbitration (HWA) must be available in order to enable multi-package mode. Multi-channel mode is always available. If the NCSI_ATTR_CHANNEL_ID attribute is present in the NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as with the NCSI_CMD_SET_INTERFACE command. The combination of preferred channel and channel whitelist defines a primary channel and the allowed failover channels. If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred channel is configured for Tx/Rx and the other channels are enabled only for Rx. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Reset channel state in ncsi_start_dev()Samuel Mendoza-Jonas
When the NCSI driver is stopped with ncsi_stop_dev() the channel monitors are stopped and the state set to "inactive". However the channels are still configured and active from the perspective of the network controller. We should suspend each active channel but in the context of ncsi_stop_dev() the transmit queue has been or is about to be stopped so we won't have time to do so. Instead when ncsi_start_dev() is called if the NCSI topology has already been probed then call ncsi_reset_dev() to suspend any channels that were previously active. This resets the network controller to a known state, provides an up to date view of channel link state, and makes sure that mode flags such as NCSI_MODE_TX_ENABLE are properly reset. In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c to update the channel configuration more cleanly. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't mark configured channels inactiveSamuel Mendoza-Jonas
The concepts of a channel being 'active' and it having link are slightly muddled in the NCSI driver. Tweak this slightly so that NCSI_CHANNEL_ACTIVE represents a channel that has been configured and enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel. This distinction is important because a channel can be 'active' but have its link down; in this case the channel may still need to be configured so that it may receive AEN link-state-change packets. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't deselect package in suspend if activeSamuel Mendoza-Jonas
When a package is deselected all channels of that package cease communication. If there are other channels active on the package of the suspended channel this will disable them as well, so only send a deselect-package command if no other channels are active. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Probe single packages to avoid conflictSamuel Mendoza-Jonas
Currently the NCSI driver sends a select-package command to all possible packages simultaneously to discover what packages are available. However at this stage in the probe process the driver does not know if hardware arbitration is available: if it isn't then this process could cause collisions on the RMII bus when packages try to respond. Update the probe loop to probe each package one by one, and once complete check if HWA is universally supported. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17net/ncsi: Don't enable all channels when HWA availableSamuel Mendoza-Jonas
NCSI hardware arbitration allows multiple packages to be enabled at once and share the same wiring. If the NCSI driver recognises that HWA is available it unconditionally enables all packages and channels; but that is a configuration decision rather than something required by HWA. Additionally the current implementation will not failover on link events which can cause connectivity to be lost unless the interface is manually bounced. Retain basic HWA support but remove the separate configuration path to enable all channels, leaving this to be handled by a later implementation. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17net/ncsi: Add NCSI Broadcom OEM commandVijay Khemka
This patch adds OEM Broadcom commands and response handling. It also defines OEM Get MAC Address handler to get and configure the device. ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for getting mac address. ncsi_rsp_handler_oem_bcm: This handles response received for all broadcom OEM commands. ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and set it to device. Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15net/ncsi: Extend NC-SI Netlink interface to allow user space to send NC-SI ↵Justin.Lee1@Dell.com
command The new command (NCSI_CMD_SEND_CMD) is added to allow user space application to send NC-SI command to the network card. Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response. The work flow is as below. Request: User space application -> Netlink interface (msg) -> new Netlink handler - ncsi_send_cmd_nl() -> ncsi_xmit_cmd() Response: Response received - ncsi_rcv_rsp() -> internal response handler - ncsi_rsp_handler_xxx() -> ncsi_rsp_handler_netlink() -> ncsi_send_netlink_rsp () -> Netlink interface (msg) -> user space application Command timeout - ncsi_request_timeout() -> ncsi_send_netlink_timeout () -> Netlink interface (msg with zero data length) -> user space application Error: Error detected -> ncsi_send_netlink_err () -> Netlink interface (err msg) -> user space application Signed-off-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05net/ncsi: Add NCSI OEM command supportVijay Khemka
This patch adds OEM commands and response handling. It also defines OEM command and response structure as per NCSI specification along with its handlers. ncsi_cmd_handler_oem: This is a generic command request handler for OEM commands ncsi_rsp_handler_oem: This is a generic response handler for OEM commands Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Justin Lee <justin.lee1@dell.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29net/ncsi: remove duplicated include from ncsi-netlink.cYueHaibing
Remove duplicated include. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-22net/ncsi: Fixup .dumpit message flags and ID check in Netlink handlerSamuel Mendoza-Jonas
The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI flag, causing additional package information after the first to be lost. Also fixup a sanity check in ncsi_write_package_info() to reject out of range package IDs. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Use netdev_dbg for debug messagesJoel Stanley
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to netdev_dbg. As Joe explains: > netdev_dbg is not included in object code unless > DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set. > And then, it is not emitted into the log unless > DEBUG is set or this specific netdev_dbg is enabled > via the dynamic debug control file. Which is what we're after in this case. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Drop no more channels messageJoel Stanley
This does not provide useful information. As the ncsi maintainer said: > either we get a channel or broadcom has gone out to lunch Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20net/ncsi: Silence debug messagesJoel Stanley
In normal operation we see this series of messages as the host drives the network device: ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up This makes all of these messages netdev_dbg. They are still useful to debug eg. misbehaving network device firmware, but we do not need them filling up the kernel logs in normal operation. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03net/ncsi: Avoid GFP_KERNEL in response handlerSamuel Mendoza-Jonas
ncsi_rsp_handler_gc() allocates the filter arrays using GFP_KERNEL in softirq context, causing the below backtrace. This allocation is only a few dozen bytes during probing so allocate with GFP_ATOMIC instead. [ 42.813372] BUG: sleeping function called from invalid context at mm/slab.h:416 [ 42.820900] in_atomic(): 1, irqs_disabled(): 0, pid: 213, name: kworker/0:1 [ 42.827893] INFO: lockdep is turned off. [ 42.832023] CPU: 0 PID: 213 Comm: kworker/0:1 Tainted: G W 4.13.16-01441-gad99b38 #65 [ 42.841007] Hardware name: Generic DT based system [ 42.845966] Workqueue: events ncsi_dev_work [ 42.850251] [<8010a494>] (unwind_backtrace) from [<80107510>] (show_stack+0x20/0x24) [ 42.858046] [<80107510>] (show_stack) from [<80612770>] (dump_stack+0x20/0x28) [ 42.865309] [<80612770>] (dump_stack) from [<80148248>] (___might_sleep+0x230/0x2b0) [ 42.873241] [<80148248>] (___might_sleep) from [<80148334>] (__might_sleep+0x6c/0xac) [ 42.881129] [<80148334>] (__might_sleep) from [<80240d6c>] (__kmalloc+0x210/0x2fc) [ 42.888737] [<80240d6c>] (__kmalloc) from [<8060ad54>] (ncsi_rsp_handler_gc+0xd0/0x170) [ 42.896770] [<8060ad54>] (ncsi_rsp_handler_gc) from [<8060b454>] (ncsi_rcv_rsp+0x16c/0x1d4) [ 42.905314] [<8060b454>] (ncsi_rcv_rsp) from [<804d86c8>] (__netif_receive_skb_core+0x3c8/0xb50) [ 42.914158] [<804d86c8>] (__netif_receive_skb_core) from [<804d96cc>] (__netif_receive_skb+0x20/0x7c) [ 42.923420] [<804d96cc>] (__netif_receive_skb) from [<804de4b0>] (netif_receive_skb_internal+0x78/0x6a4) [ 42.932931] [<804de4b0>] (netif_receive_skb_internal) from [<804df980>] (netif_receive_skb+0x78/0x158) [ 42.942292] [<804df980>] (netif_receive_skb) from [<8042f204>] (ftgmac100_poll+0x43c/0x4e8) [ 42.950855] [<8042f204>] (ftgmac100_poll) from [<804e094c>] (net_rx_action+0x278/0x4c4) [ 42.958918] [<804e094c>] (net_rx_action) from [<801016a8>] (__do_softirq+0xe0/0x4c4) [ 42.966716] [<801016a8>] (__do_softirq) from [<8011cd9c>] (do_softirq.part.4+0x50/0x78) [ 42.974756] [<8011cd9c>] (do_softirq.part.4) from [<8011cebc>] (__local_bh_enable_ip+0xf8/0x11c) [ 42.983579] [<8011cebc>] (__local_bh_enable_ip) from [<804dde08>] (__dev_queue_xmit+0x260/0x890) [ 42.992392] [<804dde08>] (__dev_queue_xmit) from [<804df1f0>] (dev_queue_xmit+0x1c/0x20) [ 43.000689] [<804df1f0>] (dev_queue_xmit) from [<806099c0>] (ncsi_xmit_cmd+0x1c0/0x244) [ 43.008763] [<806099c0>] (ncsi_xmit_cmd) from [<8060dc14>] (ncsi_dev_work+0x2e0/0x4c8) [ 43.016725] [<8060dc14>] (ncsi_dev_work) from [<80133dfc>] (process_one_work+0x214/0x6f8) [ 43.024940] [<80133dfc>] (process_one_work) from [<80134328>] (worker_thread+0x48/0x558) [ 43.033070] [<80134328>] (worker_thread) from [<8013ba80>] (kthread+0x130/0x174) [ 43.040506] [<8013ba80>] (kthread) from [<80102950>] (ret_from_fork+0x14/0x24) Fixes: 062b3e1b6d4f ("net/ncsi: Refactor MAC, VLAN filters") Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Filling in the padding slot in the bpf structure as a bug fix in 'ne' overlapped with actually using that padding area for something in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-31net/ncsi: Fix array size in dumpit handlerSamuel Mendoza-Jonas
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when parsing a NCSI_CMD_PKG_INFO command: [ 150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08 [ 150.149711] [ 150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1 [ 150.170004] Hardware name: Generic DT based system [ 150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24) [ 150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28) [ 150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278) [ 150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24) [ 150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258) [ 150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54) [ 150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284) [ 150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c) [ 150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4) [ 150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134) [ 150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44) [ 150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234) [ 150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0) [ 150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34) [ 150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260) [ 150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c) [ 150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c) [ 150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c) [ 150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08 This turns out to be because the attrs array in ncsi_pkg_info_all_nl() is initialised to a length of NCSI_ATTR_MAX which is the maximum attribute number, not the number of attributes. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-29net: remove unnecessary genlmsg_cancel() callsYueHaibing
the message be freed immediately, no need to trim it back to the previous size. Inspired by commit 7a9b3ec1e19f ("nl80211: remove unnecessary genlmsg_cancel() calls") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>