summaryrefslogtreecommitdiff
path: root/net/sctp
AgeCommit message (Collapse)Author
2018-06-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Various netfilter fixlets from Pablo and the netfilter team. 2) Fix regression in IPVS caused by lack of PMTU exceptions on local routes in ipv6, from Julian Anastasov. 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia. 4) Don't crash on poll in TLS, from Daniel Borkmann. 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things including Avahi mDNS. From Bart Van Assche. 6) Missing of_node_put in qcom/emac driver, from Yue Haibing. 7) We lack checking of the TCP checking in one special case during SYN receive, from Frank van der Linden. 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg. 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman. 10) Must grab HW caps before doing quirk checks in stmmac driver, from Jose Abreu. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits) net: stmmac: Run HWIF Quirks after getting HW caps neighbour: skip NTF_EXT_LEARNED entries during forced gc net: cxgb3: add error handling for sysfs_create_group tls: fix waitall behavior in tls_sw_recvmsg tls: fix use-after-free in tls_push_record l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl() l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels mlxsw: spectrum_switchdev: Fix port_vlan refcounting mlxsw: spectrum_router: Align with new route replace logic mlxsw: spectrum_router: Allow appending to dev-only routes ipv6: Only emit append events for appended routes stmmac: added support for 802.1ad vlan stripping cfg80211: fix rcu in cfg80211_unregister_wdev mac80211: Move up init of TXQs mac80211_hwsim: fix module init error paths cfg80211: initialize sinfo in cfg80211_get_station nl80211: fix some kernel doc tag mistakes hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload rds: avoid unenecessary cong_update in loop transport l2tp: clean up stale tunnel or session in pppol2tp_connect's error path ...
2018-06-14sctp: define sctp_packet_gso_append to build GSO framesXin Long
Now sctp GSO uses skb_gro_receive() to append the data into head skb frag_list. However it actually only needs very few code from skb_gro_receive(). Besides, NAPI_GRO_CB has to be set while most of its members are not needed here. This patch is to add sctp_packet_gso_append() to build GSO frames instead of skb_gro_receive(), and it would avoid many unnecessary checks and make the code clearer. Note that sctp will use page frags instead of frag_list to build GSO frames in another patch. But it may take time, as sctp's GSO frames may have different size. skb_segment() can only split it into the frags with the same size, which would break the border of sctp chunks. Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12treewide: kmalloc() -> kmalloc_array()Kees Cook
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Add Maglev hashing scheduler to IPVS, from Inju Song. 2) Lots of new TC subsystem tests from Roman Mashak. 3) Add TCP zero copy receive and fix delayed acks and autotuning with SO_RCVLOWAT, from Eric Dumazet. 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard Brouer. 5) Add ttl inherit support to vxlan, from Hangbin Liu. 6) Properly separate ipv6 routes into their logically independant components. fib6_info for the routing table, and fib6_nh for sets of nexthops, which thus can be shared. From David Ahern. 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP messages from XDP programs. From Nikita V. Shirokov. 8) Lots of long overdue cleanups to the r8169 driver, from Heiner Kallweit. 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau. 10) Add traffic condition monitoring to iwlwifi, from Luca Coelho. 11) Plumb extack down into fib_rules, from Roopa Prabhu. 12) Add Flower classifier offload support to igb, from Vinicius Costa Gomes. 13) Add UDP GSO support, from Willem de Bruijn. 14) Add documentation for eBPF helpers, from Quentin Monnet. 15) Add TLS tx offload to mlx5, from Ilya Lesokhin. 16) Allow applications to be given the number of bytes available to read on a socket via a control message returned from recvmsg(), from Soheil Hassas Yeganeh. 17) Add x86_32 eBPF JIT compiler, from Wang YanQing. 18) Add AF_XDP sockets, with zerocopy support infrastructure as well. From Björn Töpel. 19) Remove indirect load support from all of the BPF JITs and handle these operations in the verifier by translating them into native BPF instead. From Daniel Borkmann. 20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha. 21) Allow XDP programs to do lookups in the main kernel routing tables for forwarding. From David Ahern. 22) Allow drivers to store hardware state into an ELF section of kernel dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy. 23) Various RACK and loss detection improvements in TCP, from Yuchung Cheng. 24) Add TCP SACK compression, from Eric Dumazet. 25) Add User Mode Helper support and basic bpfilter infrastructure, from Alexei Starovoitov. 26) Support ports and protocol values in RTM_GETROUTE, from Roopa Prabhu. 27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard Brouer. 28) Add lots of forwarding selftests, from Petr Machata. 29) Add generic network device failover driver, from Sridhar Samudrala. * ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits) strparser: Add __strp_unpause and use it in ktls. rxrpc: Fix terminal retransmission connection ID to include the channel net: hns3: Optimize PF CMDQ interrupt switching process net: hns3: Fix for VF mailbox receiving unknown message net: hns3: Fix for VF mailbox cannot receiving PF response bnx2x: use the right constant Revert "net: sched: cls: Fix offloading when ingress dev is vxlan" net: dsa: b53: Fix for brcm tag issue in Cygnus SoC enic: fix UDP rss bits netdev-FAQ: clarify DaveM's position for stable backports rtnetlink: validate attributes in do_setlink() mlxsw: Add extack messages for port_{un, }split failures netdevsim: Add extack error message for devlink reload devlink: Add extack to reload and port_{un, }split operations net: metrics: add proper netlink validation ipmr: fix error path when ipmr_new_table fails ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds net: hns3: remove unused hclgevf_cfg_func_mta_filter netfilter: provide udp*_lib_lookup for nf_tproxy qed*: Utilize FW 8.37.2.0 ...
2018-06-06Merge tag 'overflow-v4.18-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull overflow updates from Kees Cook: "This adds the new overflow checking helpers and adds them to the 2-factor argument allocators. And this adds the saturating size helpers and does a treewide replacement for the struct_size() usage. Additionally this adds the overflow testing modules to make sure everything works. I'm still working on the treewide replacements for allocators with "simple" multiplied arguments: *alloc(a * b, ...) -> *alloc_array(a, b, ...) and *zalloc(a * b, ...) -> *calloc(a, b, ...) as well as the more complex cases, but that's separable from this portion of the series. I expect to have the rest sent before -rc1 closes; there are a lot of messy cases to clean up. Summary: - Introduce arithmetic overflow test helper functions (Rasmus) - Use overflow helpers in 2-factor allocators (Kees, Rasmus) - Introduce overflow test module (Rasmus, Kees) - Introduce saturating size helper functions (Matthew, Kees) - Treewide use of struct_size() for allocators (Kees)" * tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: treewide: Use struct_size() for devm_kmalloc() and friends treewide: Use struct_size() for vmalloc()-family treewide: Use struct_size() for kmalloc()-family device: Use overflow helpers for devm_kmalloc() mm: Use overflow helpers in kvmalloc() mm: Use overflow helpers in kmalloc_array*() test_overflow: Add memory allocation overflow tests overflow.h: Add allocation size calculation helpers test_overflow: Report test failures test_overflow: macrofy some more, do more tests for free lib: add runtime test of check_*_overflow functions compiler.h: enable builtin overflow checkers and add fallback code
2018-06-06treewide: Use struct_size() for kmalloc()-familyKees Cook
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL); This patch makes the changes for kmalloc()-family (and kvmalloc()-family) uses. It was done via automatic conversion with manual review for the "CHECKME" non-standard cases noted below, using the following Coccinelle script: // pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len * // sizeof *pkey_cache->table, GFP_KERNEL); @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; identifier VAR, ELEMENT; expression COUNT; @@ - alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP) + alloc(struct_size(VAR, ELEMENT, COUNT), GFP) // mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL); @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; identifier VAR, ELEMENT; expression COUNT; @@ - alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP) + alloc(struct_size(VAR, ELEMENT, COUNT), GFP) // Same pattern, but can't trivially locate the trailing element name, // or variable name. @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; expression SOMETHING, COUNT, ELEMENT; @@ - alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP) + alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-05sctp: not allow transport timeout value less than HZ/5 for hb_timerXin Long
syzbot reported a rcu_sched self-detected stall on CPU which is caused by too small value set on rto_min with SCTP_RTOINFO sockopt. With this value, hb_timer will get stuck there, as in its timer handler it starts this timer again with this value, then goes to the timer handler again. This problem is there since very beginning, and thanks to Eric for the reproducer shared from a syzbot mail. This patch fixes it by not allowing sctp_transport_timeout to return a smaller value than HZ/5 for hb_timer, which is based on TCP's min rto. Note that it doesn't fix this issue by limiting rto_min, as some users are still using small rto and no proper value was found for it yet. Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-04Merge branch 'work.aio-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull aio updates from Al Viro: "Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly. The only thing I'm holding back for a day or so is Adam's aio ioprio - his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case), but let it sit in -next for decency sake..." * 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits) aio: sanitize the limit checking in io_submit(2) aio: fold do_io_submit() into callers aio: shift copyin of iocb into io_submit_one() aio_read_events_ring(): make a bit more readable aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way aio: take list removal to (some) callers of aio_complete() aio: add missing break for the IOCB_CMD_FDSYNC case random: convert to ->poll_mask timerfd: convert to ->poll_mask eventfd: switch to ->poll_mask pipe: convert to ->poll_mask crypto: af_alg: convert to ->poll_mask net/rxrpc: convert to ->poll_mask net/iucv: convert to ->poll_mask net/phonet: convert to ->poll_mask net/nfc: convert to ->poll_mask net/caif: convert to ->poll_mask net/bluetooth: convert to ->poll_mask net/sctp: convert to ->poll_mask net/tipc: convert to ->poll_mask ...
2018-06-04Merge branch 'hch.procfs' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull procfs updates from Al Viro: "Christoph's proc_create_... cleanups series" * 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits) xfs, proc: hide unused xfs procfs helpers isdn/gigaset: add back gigaset_procinfo assignment proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields tty: replace ->proc_fops with ->proc_show ide: replace ->proc_fops with ->proc_show ide: remove ide_driver_proc_write isdn: replace ->proc_fops with ->proc_show atm: switch to proc_create_seq_private atm: simplify procfs code bluetooth: switch to proc_create_seq_data netfilter/x_tables: switch to proc_create_seq_private netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data neigh: switch to proc_create_seq_data hostap: switch to proc_create_{seq,single}_data bonding: switch to proc_create_seq_data rtc/proc: switch to proc_create_single_data drbd: switch to proc_create_single resource: switch to proc_create_seq_data staging/rtl8192u: simplify procfs code jfs: simplify procfs code ...
2018-05-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Lots of easy overlapping changes in the confict resolutions here. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-26net/sctp: convert to ->poll_maskChristoph Hellwig
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-22sctp: fix the issue that flags are ignored when using kernel_connectXin Long
Now sctp uses inet_dgram_connect as its proto_ops .connect, and the flags param can't be passed into its proto .connect where this flags is really needed. sctp works around it by getting flags from socket file in __sctp_connect. It works for connecting from userspace, as inherently the user sock has socket file and it passes f_flags as the flags param into the proto_ops .connect. However, the sock created by sock_create_kern doesn't have a socket file, and it passes the flags (like O_NONBLOCK) by using the flags param in kernel_connect, which calls proto_ops .connect later. So to fix it, this patch defines a new proto_ops .connect for sctp, sctp_inet_connect, which calls __sctp_connect() directly with this flags param. After this, the sctp's proto .connect can be removed. Note that sctp_inet_connect doesn't need to do some checks that are not needed for sctp, which makes thing better than with inet_dgram_connect. Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-16proc: introduce proc_create_net_singleChristoph Hellwig
Variant of proc_create_data that directly take a seq_file show callback and deals with network namespaces in ->open and ->release. All callers of proc_create + single_open_net converted over, and single_{open,release}_net are removed entirely. Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-16proc: introduce proc_create_net{,_data}Christoph Hellwig
Variants of proc_create{,_data} that directly take a struct seq_operations and deal with network namespaces in ->open and ->release. All callers of proc_create + seq_open_net converted over, and seq_{open,release}_net are removed entirely. Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-16proc: introduce proc_create_seq{,_data}Christoph Hellwig
Variants of proc_create{,_data} that directly take a struct seq_operations argument and drastically reduces the boilerplate code in the callers. All trivial callers converted over. Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-14sctp: checkpatch fixupsMarcelo Ricardo Leitner
A collection of fixups from previous patches, left for later to not introduce unnecessary changes while moving code around. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: add asoc and packet to sctp_flush_ctxMarcelo Ricardo Leitner
Pre-compute these so the compiler won't reload them (due to no-strict-aliasing). Changes since v2: - Do not replace a return with a break in sctp_outq_flush_data Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: add sctp_flush_ctx, a context struct on outq_flush routinesMarcelo Ricardo Leitner
With this struct we avoid passing lots of variables around and taking care of updating the current transport/packet. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: rework switch cases in sctp_outq_flush_dataMarcelo Ricardo Leitner
Remove an inner one, which tended to be error prone due to the cascading and it can be replaced by a simple if (). Rework the outer one so that the actual flush code is not inside it. Now we first validate if we can or cannot send data, return if not, and then the flush code. Suggested-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: make use of gfp on retransmissionsMarcelo Ricardo Leitner
Retransmissions may be triggered when in user context, so lets make use of gfp. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: move transport flush code out of sctp_outq_flushMarcelo Ricardo Leitner
To the new sctp_outq_flush_transports. Comment on Nagle is outdated and removed. Nagle is performed earlier, while checking if the chunk fits the packet: if the outq length is not enough to fill the packet, it returns SCTP_XMIT_DELAY. So by when it gets to sctp_outq_flush_transports, it has to go through all enlisted transports. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: move flushing of data chunks out of sctp_outq_flushMarcelo Ricardo Leitner
To the new sctp_outq_flush_data. Again, smaller functions and with well defined objectives. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: move outq data rtx code out of sctp_outq_flushMarcelo Ricardo Leitner
This patch renames current sctp_outq_flush_rtx to __sctp_outq_flush_rtx and create a new sctp_outq_flush_rtx, with the code that was on sctp_outq_flush. Again, the idea is to have functions with small and defined objectives. Yes, there is an open-coded path selection in the now sctp_outq_flush_rtx. That is kept as is for now because it may be very different when we implement retransmission path selection algorithms for CMT-SCTP. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: move the flush of ctrl chunks into its own functionMarcelo Ricardo Leitner
Named sctp_outq_flush_ctrl and, with that, keep the contexts contained. One small fix embedded is the reset of one_packet at every iteration. This allows bundling of some control chunks in case they were preceeded by another control chunk that cannot be bundled. Other than this, it has the same behavior. Changes since v2: - Fixed panic reported by kbuild test robot if building with only up to this patch applied, due to bad parameter to sctp_outq_select_transport and by not initializing packet after calling sctp_outq_flush_ctrl. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: factor out sctp_outq_select_transportMarcelo Ricardo Leitner
We had two spots doing such complex operation and they were very close to each other, a bit more tailored to here or there. This patch unifies these under the same function, sctp_outq_select_transport, which knows how to handle control chunks and original transmissions (but not retransmissions). Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14sctp: add sctp_packet_singletonMarcelo Ricardo Leitner
Factor out the code for generating singletons. It's used only once, but helps to keep the context contained. The const variables are to ease the reading of subsequent calls in there. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
The bpf syscall and selftests conflicts were trivial overlapping changes. The r8169 change involved moving the added mdelay from 'net' into a different function. A TLS close bug fix overlapped with the splitting of the TLS state into separate TX and RX parts. I just expanded the tests in the bug fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf == X". Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10sctp: remove sctp_chunk_put from fail_mark err path in sctp_ulpevent_make_rcvmsgXin Long
In Commit 1f45f78f8e51 ("sctp: allow GSO frags to access the chunk too"), it held the chunk in sctp_ulpevent_make_rcvmsg to access it safely later in recvmsg. However, it also added sctp_chunk_put in fail_mark err path, which is only triggered before holding the chunk. syzbot reported a use-after-free crash happened on this err path, where it shouldn't call sctp_chunk_put. This patch simply removes this call. Fixes: 1f45f78f8e51 ("sctp: allow GSO frags to access the chunk too") Reported-by: syzbot+141d898c5f24489db4aa@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10sctp: fix spelling mistake: "max_retans" -> "max_retrans"Colin Ian King
Trivial fix to spelling mistake in error string Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-07sctp: delay the authentication for the duplicated cookie-echo chunkXin Long
Now sctp only delays the authentication for the normal cookie-echo chunk by setting chunk->auth_chunk in sctp_endpoint_bh_rcv(). But for the duplicated one with auth, in sctp_assoc_bh_rcv(), it does authentication first based on the old asoc, which will definitely fail due to the different auth info in the old asoc. The duplicated cookie-echo chunk will create a new asoc with the auth info from this chunk, and the authentication should also be done with the new asoc's auth info for all of the collision 'A', 'B' and 'D'. Otherwise, the duplicated cookie-echo chunk with auth will never pass the authentication and create the new connection. This issue exists since very beginning, and this fix is to make sctp_assoc_bh_rcv() follow the way sctp_endpoint_bh_rcv() does for the normal cookie-echo chunk to delay the authentication. While at it, remove the unused params from sctp_sf_authenticate() and define sctp_auth_chunk_verify() used for all the places that do the delayed authentication. v1->v2: fix the typo in changelog as Marcelo noticed. Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Overlapping changes in selftests Makefile. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-02sctp: fix the issue that the cookie-ack with auth can't get processedXin Long
When auth is enabled for cookie-ack chunk, in sctp_inq_pop, sctp processes auth chunk first, then continues to the next chunk in this packet if chunk_end + chunk_hdr size < skb_tail_pointer(). Otherwise, it will go to the next packet or discard this chunk. However, it missed the fact that cookie-ack chunk's size is equal to chunk_hdr size, which couldn't match that check, and thus this chunk would not get processed. This patch fixes it by changing the check to chunk_end + chunk_hdr size <= skb_tail_pointer(). Fixes: 26b87c788100 ("net: sctp: fix remote memory pressure from excessive queueing") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-02sctp: use the old asoc when making the cookie-ack chunk in dupcook_dXin Long
When processing a duplicate cookie-echo chunk, for case 'D', sctp will not process the param from this chunk. It means old asoc has nothing to be updated, and the new temp asoc doesn't have the complete info. So there's no reason to use the new asoc when creating the cookie-ack chunk. Otherwise, like when auth is enabled for cookie-ack, the chunk can not be set with auth, and it will definitely be dropped by peer. This issue is there since very beginning, and we fix it by using the old asoc instead. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-02sctp: init active key for the new asoc in dupcook_a and dupcook_bXin Long
When processing a duplicate cookie-echo chunk, for case 'A' and 'B', after sctp_process_init for the new asoc, if auth is enabled for the cookie-ack chunk, the active key should also be initialized. Otherwise, the cookie-ack chunk made later can not be set with auth shkey properly, and a crash can even be caused by this, as after Commit 1b1e0bc99474 ("sctp: add refcnt support for sh_key"), sctp needs to hold the shkey when making control chunks. Fixes: 1b1e0bc99474 ("sctp: add refcnt support for sh_key") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-01sctp: add sctp_make_op_error_limited and reuse inner functionsMarcelo Ricardo Leitner
The idea is quite similar to the old functions, but note that the _fixed function wasn't "fixed" as in that it would generate a packet with a fixed size, but rather limited/bounded to PMTU. Also, now with sctp_mtu_payload(), we have a more accurate limit. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-01sctp: allow sctp_init_cause to return errorsMarcelo Ricardo Leitner
And do so if the skb doesn't have enough space for the payload. This is a preparation for the next patch. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: allow unsetting sockopt MAXSEGMarcelo Ricardo Leitner
RFC 6458 Section 8.1.16 says that setting MAXSEG as 0 means that the user is not limiting it, and not that it should set to the *current* maximum, as we are doing. This patch thus allow setting it as 0, effectively removing the user limit. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: consider idata chunks when setting SCTP_MAXSEGMarcelo Ricardo Leitner
When setting SCTP_MAXSEG sock option, it should consider which kind of data chunk is being used if the asoc is already available, so that the limit better reflect reality. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: honor PMTU_DISABLED when handling icmpMarcelo Ricardo Leitner
sctp_sendmsg() could trigger PMTU updates even when PMTU_DISABLED was set, as pmtu_pending could be set unconditionally during icmp handling if the socket was in use by the application. This patch fixes it by checking for PMTU_DISABLED when handling such deferred updates. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: re-use sctp_transport_pmtu in sctp_transport_routeMarcelo Ricardo Leitner
sctp_transport_route currently is very similar to sctp_transport_pmtu plus a few other bits. This patch reuses sctp_transport_pmtu in sctp_transport_route and removes the duplicated code. Also, as all calls to sctp_transport_route were forcing the dst release before calling it, let's just include such release too. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: remove sctp_transport_pmtu_checkMarcelo Ricardo Leitner
We are now keeping the MTU information synced between asoc, transport and dst, which makes the check at sctp_packet_config() not needed anymore. As it was the sole caller to this function, lets remove it. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: introduce sctp_dst_mtuMarcelo Ricardo Leitner
Which makes sure that the MTU respects the minimum value of SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: remove sctp_assoc_pending_pmtuMarcelo Ricardo Leitner
No need for this helper. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: introduce sctp_assoc_update_frag_pointMarcelo Ricardo Leitner
and avoid the open-coded versions of it. Now sctp_datamsg_from_user can just re-use asoc->frag_point as it will always be updated. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: introduce sctp_mtu_payloadMarcelo Ricardo Leitner
When given a MTU, this function calculates how much payload we can carry on it. Without a MTU, it calculates the amount of header overhead we have. So that when we have extra overhead, like the one added for IP options on SELinux patches, it is easier to handle it. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: introduce sctp_assoc_set_pmtuMarcelo Ricardo Leitner
All changes to asoc PMTU should now go through this wrapper, making it easier to track them and to do other actions upon it. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: remove an if() that is always trueMarcelo Ricardo Leitner
As noticed by Xin Long, the if() here is always true as PMTU can never be 0. Reported-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: move transport pathmtu calc away of sctp_assoc_add_peerMarcelo Ricardo Leitner
There was only one case that sctp_assoc_add_peer couldn't handle, which is when SPP_PMTUD_DISABLE is set and pathmtu not initialized. So add this situation to sctp_transport_route and reuse what was already in there. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: clear the new asoc's stream outcnt in sctp_stream_updateXin Long
When processing a duplicate cookie-echo chunk, sctp moves the new temp asoc's stream out/in into the old asoc, and later frees this new temp asoc. But now after this move, the new temp asoc's stream->outcnt is not cleared while stream->out is set to NULL, which would cause a same crash as the one fixed in Commit 79d0895140e9 ("sctp: fix error path in sctp_stream_init") when freeing this asoc later. This fix is to clear this outcnt in sctp_stream_update. Fixes: f952be79cebd ("sctp: introduce struct sctp_stream_out_ext") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>