| Age | Commit message (Collapse) | Author |
|---|
|
commit 817298102b0b ("tipc: fix link priority propagation") introduced a
compatibility problem between TIPC versions newer than Linux 4.6 and
those older than Linux 4.4. In versions later than 4.4, link STATE
messages only contain a non-zero link priority value when the sender
wants the receiver to change its priority. This has the effect that the
receiver resets itself in order to apply the new priority. This works
well, and is consistent with the said commit.
However, in versions older than 4.4 a valid link priority is present in
all sent link STATE messages, leading to cyclic link establishment and
reset on the 4.6+ node.
We fix this by adding a test that the received value should not only
be valid, but also differ from the current value in order to cause the
receiving link endpoint to reset.
Reported-by: Amar Nv <amar.nv005@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comment block in socket.c describing the locking policy is
obsolete, and does not reflect current reality. We remove it in this
commit.
Since the current locking policy is much simpler and follows a
mainstream approach, we see no need to add a new description.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 14135f30e33c ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we replace references to sock->state SS_CONNECTE
with sk_state TIPC_ESTABLISHED.
Finally, the sock->state is no longer explicitly used by tipc.
The FSM below is for various types of connection oriented sockets.
Stream Server Listening Socket:
+-----------+ +-------------+
| TIPC_OPEN |------>| TIPC_LISTEN |
+-----------+ +-------------+
Stream Server Data Socket:
+-----------+ +------------------+
| TIPC_OPEN |------>| TIPC_ESTABLISHED |
+-----------+ +------------------+
^ |
| |
| v
+--------------------+
| TIPC_DISCONNECTING |
+--------------------+
Stream Socket Client:
+-----------+ +-----------------+
| TIPC_OPEN |------>| TIPC_CONNECTING |------+
+-----------+ +-----------------+ |
| |
| |
v |
+------------------+ |
| TIPC_ESTABLISHED | |
+------------------+ |
^ | |
| | |
| v |
+--------------------+ |
| TIPC_DISCONNECTING |<--+
+--------------------+
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we create a new tipc socket state TIPC_CONNECTING
by primarily replacing the SS_CONNECTING with TIPC_CONNECTING.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we replace the references to SS_DISCONNECTING with
the combination of sk_state TIPC_DISCONNECTING and flags set in
sk_shutdown.
We introduce a new function _tipc_shutdown(), which provides
the common code required by tipc_release() and tipc_shutdown().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we create a new tipc socket state TIPC_DISCONNECTING in
sk_state. TIPC_DISCONNECTING is replacing the socket connection status
update using SS_DISCONNECTING.
TIPC_DISCONNECTING is set for connection oriented sockets at:
- tipc_shutdown()
- connection probe timeout
- when we receive an error message on the connection.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we create a new tipc socket state TIPC_OPEN in
sk_state. We primarily replace the SS_UNCONNECTED sock->state with
TIPC_OPEN.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, tipc maintains probing state for connected sockets in
tsk->probing_state variable.
In this commit, we express this information as socket states and
this remove the variable. We set probe_unacked flag when a probe
is sent out and reset it if we receive a reply. Instead of the
probing state TIPC_CONN_OK, we create a new state TIPC_ESTABLISHED.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, tipc maintains the socket state in sock->state variable.
This is used to maintain generic socket states, but in tipc
we overload it and save tipc socket states like TIPC_LISTEN.
Other protocols like TCP, UDP store protocol specific states
in sk->sk_state instead.
In this commit, we :
- declare a new tipc state TIPC_LISTEN, that replaces SS_LISTEN
- Create a new function tipc_set_state(), to update sk->sk_state.
- TIPC_LISTEN state is maintained in sk->sk_state.
- replace references to SS_LISTEN with TIPC_LISTEN.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, tipc socket state SS_READY declares that the socket is a
connectionless socket.
In this commit, we remove the state SS_READY and replace it with a
condition which returns true for datagram / connectionless sockets.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, probing_intv is a variable in struct tipc_sock but is
always set to a constant CONN_PROBING_INTERVAL. The socket
connection is probed based on this value.
In this commit, we remove this variable and setup the socket
timer based on the constant CONN_PROBING_INTERVAL.
There is no functional change in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we determine if a socket is connected or not based on
tsk->connected, which is set once when the probing state is set
to TIPC_CONN_OK. It is unset when the sock->state is updated from
SS_CONNECTED to any other state.
In this commit, we remove connected variable from tipc_sock and
derive socket connection status from the following condition:
sock->state == SS_CONNECTED => tsk->connected
There is no functional change in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, for connectionless sockets the peer information during
connect is stored in tsk->peer and a connection state is set in
tsk->connected. This is redundant.
In this commit, for connectionless sockets we update:
- __tipc_sendmsg(), when the destination is NULL the peer existence
is determined by tsk->peer.family, instead of tsk->connected.
- tipc_connect(), remove set/unset of tsk->connected.
Hence tsk->connected is no longer used for connectionless sockets.
There is no functional change in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the peer information for connect is stored in tsk->remote
but the rest of code uses the name peer for peer/remote.
In this commit, we rename tsk->remote to tsk->peer to align with
naming convention followed in the rest of the code.
There is no functional change in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we rename handle to bytes_read indicating the
purpose of the member.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, tipc_accept() calls sk_alloc() with kern=1. This is
incorrect as the data socket's owner is the user application.
Thus for these accepted data sockets the network namespace
refcount is skipped.
In this commit, we fix this by setting kern=0.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, in filter_connect() when we terminate a connection due to
an error message from peer, we set the socket state to DISCONNECTING.
The socket is notified about this broken connection using EPIPE when
a user tries to send a message. However if a socket was waiting on a
poll() while the connection is being terminated, we fail to wakeup
that socket.
In this commit, we wakeup sleeping sockets at connection termination.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, in stream/mcast send() we pass the message to the link
layer even when the link is congested and add the socket to the
link's wakeup queue. This is unnecessary for non-blocking sockets.
If a socket is set to non-blocking and sends multicast with zero
back off time while receiving EAGAIN, we exhaust the memory.
In this commit, we return immediately at stream/mcast send() for
non-blocking sockets.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 2d18ac4ba745 ("tipc: extend broadcast link initialization
criteria") we tried to fix a problem with the initial synchronization
of broadcast link acknowledge values. Unfortunately that solution is
not sufficient to solve the issue.
We have seen it happen that LINK_PROTOCOL/STATE packets with a valid
non-zero unicast acknowledge number may bypass BCAST_PROTOCOL
initialization, NAME_DISTRIBUTOR and other STATE packets with invalid
broadcast acknowledge numbers, leading to premature opening of the
broadcast link. When the bypassed packets finally arrive, they are
inadvertently accepted, and the already correctly initialized
acknowledge number in the broadcast receive link is overwritten by
the invalid (zero) value of the said packets. After this the broadcast
link goes stale.
We now fix this by marking the packets where we know the acknowledge
value is or may be invalid, and then ignoring the acks from those.
To this purpose, we claim an unused bit in the header to indicate that
the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL
synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR
packets, plus those LINK_PROTOCOL packets sent out before the broadcast
links are fully synchronized.
This minor protocol update is fully backwards compatible.
Reported-by: John Thompson <thompa.atl@gmail.com>
Tested-by: John Thompson <thompa.atl@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This helper function allows family implementations to access
their family's attrbuf. This gets rid of the attrbuf usage
in families, and also adds locking validation, since it's not
valid to use the attrbuf with parallel_ops or outside of the
dumpit callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should clear out the padding and unused struct members so that we
don't expose stack information to userspace.
Fixes: fdb3accc2c15 ('tipc: add the ability to get UDP options via netlink')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ub' is malloced in tipc_udp_enable() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ba5aa84a2d22 ("tipc: split UDP nl address parsing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because of the risk of an excessive number of NACK messages and
retransissions, receivers have until now abstained from sending
broadcast NACKS directly upon detection of a packet sequence number
gap. We have instead relied on such gaps being detected by link
protocol STATE message exchange, something that by necessity delays
such detection and subsequent retransmissions.
With the introduction of unicast NACK transmission and rate control
of retransmissions we can now remove this limitation. We now allow
receiving nodes to send NACKS immediately, while coordinating the
permission to do so among the nodes in order to avoid NACK storms.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As cluster sizes grow, so does the amount of identical or overlapping
broadcast NACKs generated by the packet receivers. This often leads to
'NACK crunches' resulting in huge numbers of redundant retransmissions
of the same packet ranges.
In this commit, we introduce rate control of broadcast retransmissions,
so that a retransmitted range cannot be retransmitted again until after
at least 10 ms. This reduces the frequency of duplicate, redundant
retransmissions by an order of magnitude, while having a significant
positive impact on overall throughput and scalability.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we send broadcasts in clusters of more 70-80 nodes, we sometimes
see the broadcast link resetting because of an excessive number of
retransmissions. This is caused by a combination of two factors:
1) A 'NACK crunch", where loss of broadcast packets is discovered
and NACK'ed by several nodes simultaneously, leading to multiple
redundant broadcast retransmissions.
2) The fact that the NACKS as such also are sent as broadcast, leading
to excessive load and packet loss on the transmitting switch/bridge.
This commit deals with the latter problem, by moving sending of
broadcast nacks from the dedicated BCAST_PROTOCOL/NACK message type
to regular unicast LINK_PROTOCOL/STATE messages. We allocate 10 unused
bits in word 8 of the said message for this purpose, and introduce a
new capability bit, TIPC_BCAST_STATE_NACK in order to keep the change
backwards compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a dual bearer configuration, if the second tipc link becomes
active while the first link still has pending nametable "bulk"
updates, it randomly leads to reset of the second link.
When a link is established, the function named_distribute(),
fills the skb based on node mtu (allows room for TUNNEL_PROTOCOL)
with NAME_DISTRIBUTOR message for each PUBLICATION.
However, the function named_distribute() allocates the buffer by
increasing the node mtu by INT_H_SIZE (to insert NAME_DISTRIBUTOR).
This consumes the space allocated for TUNNEL_PROTOCOL.
When establishing the second link, the link shall tunnel all the
messages in the first link queue including the "bulk" update.
As size of the NAME_DISTRIBUTOR messages while tunnelling, exceeds
the link mtu the transmission fails (-EMSGSIZE).
Thus, the synch point based on the message count of the tunnel
packets is never reached leading to link timeout.
In this commit, we adjust the size of name distributor message so that
they can be tunnelled.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All three conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using replicast a UDP bearer can have an arbitrary amount of
remote ip addresses associated with it. This means we cannot simply
add all remote ip addresses to an existing bearer data message as it
might fill the message, leaving us with a truncated message that we
can't safely resume. To handle this we introduce the new netlink
command TIPC_NL_UDP_GET_REMOTEIP. This command is intended to be
called when the bearer data message has the
TIPC_NLA_UDP_MULTI_REMOTEIP flag set, indicating there are more than
one remote ip (replicast).
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add UDP bearer options to netlink bearer get message. This is used by
the tipc user space tool to display UDP options.
The UDP bearer information is passed using either a sockaddr_in or
sockaddr_in6 structs. This means the user space receiver should
intermediately store the retrieved data in a large enough struct
(sockaddr_strage) before casting to the proper IP version type.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Automatically learn UDP remote IP addresses of communicating peers by
looking at the source IP address of incoming TIPC link configuration
messages (neighbor discovery).
This makes configuration slightly easier and removes the problematic
scenario where a node receives directly addressed neighbor discovery
messages sent using replicast which the node cannot "reply" to using
mutlicast, leaving the link FSM in a limbo state.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces UDP replicast. A concept where we emulate
multicast by sending multiple unicast messages to configured peers.
The purpose of replicast is mainly to be able to use TIPC in cloud
environments where IP multicast is disabled. Using replicas to unicast
multicast messages is costly as we have to copy each skb and send the
copies individually.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function to check if a tipc UDP media address is a multicast
address or not. This is a purely cosmetic change.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split the UDP send function into two. One callback that prepares the
skb and one transmit function that sends the skb. This will come in
handy in later patches, when we introduce UDP replicast.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split the UDP netlink parse function so that it only parses one
netlink attribute at the time. This makes the parse function more
generic and allow future UDP API functions to use it for parsing.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code in enable_mcast() error handling
case, and release udp socket when necessary.
Fixes: d0f91938bede ("tipc: add ip/udp media type")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kfree_skb() instead of kfree() to free sk_buff.
Fixes: 0d051bf93c06 ("tipc: make bearer packet filtering generic")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_PEER_REMOVE netlink command. This command can remove
an offline peer node from the internal data structures.
This will be supported by the tipc user space tool in iproute2.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link is attempted woken up after congestion, it uses a different,
more generous criteria than when it was originally declared congested.
This has the effect that the link, and the sending process, sometimes
will be woken up unnecessarily, just to immediately return to congestion
when it turns out there is not not enough space in its send queue to
host the pending message. This is a waste of CPU cycles.
We now change the function link_prepare_wakeup() to use exactly the same
criteria as tipc_link_xmit(). However, since we are now excluding the
window limit from the wakeup calculation, and the current backlog limit
for the lowest level is too small to house even a single maximum-size
message, we have to expand this limit. We do this by evaluating an
alternative, minimum value during the setting of the importance limits.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 5b7066c3dd24 ("tipc: stricter filtering of packets in bearer
layer") we introduced a method of filtering out messages while a bearer
is being reset, to avoid that links may be re-created and come back in
working state while we are still in the process of shutting them down.
This solution works well, but is limited to only work with L2 media, which
is insufficient with the increasing use of UDP as carrier media.
We now replace this solution with a more generic one, by introducing a
new flag "up" in the generic struct tipc_bearer. This field will be set
and reset at the same locations as with the previous solution, while
the packet filtering is moved to the generic code for the sending side.
On the receiving side, the filtering is still done in media specific
code, but now including the UDP bearer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tipc_msg_create() can return a NULL skb and if so, we shouldn't try to
call tipc_node_xmit_skb() on it.
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 3 PID: 30298 Comm: trinity-c0 Not tainted 4.7.0-rc7+ #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff8800baf09980 ti: ffff8800595b8000 task.ti: ffff8800595b8000
RIP: 0010:[<ffffffff830bb46b>] [<ffffffff830bb46b>] tipc_node_xmit_skb+0x6b/0x140
RSP: 0018:ffff8800595bfce8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003023b0e0
RDX: 0000000000000000 RSI: dffffc0000000000 RDI: ffffffff83d12580
RBP: ffff8800595bfd78 R08: ffffed000b2b7f32 R09: 0000000000000000
R10: fffffbfff0759725 R11: 0000000000000000 R12: 1ffff1000b2b7f9f
R13: ffff8800595bfd58 R14: ffffffff83d12580 R15: dffffc0000000000
FS: 00007fcdde242700(0000) GS:ffff88011af80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fcddde1db10 CR3: 000000006874b000 CR4: 00000000000006e0
DR0: 00007fcdde248000 DR1: 00007fcddd73d000 DR2: 00007fcdde248000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000090602
Stack:
0000000000000018 0000000000000018 0000000041b58ab3 ffffffff83954208
ffffffff830bb400 ffff8800595bfd30 ffffffff8309d767 0000000000000018
0000000000000018 ffff8800595bfd78 ffffffff8309da1a 00000000810ee611
Call Trace:
[<ffffffff830c84a3>] tipc_shutdown+0x553/0x880
[<ffffffff825b4a3b>] SyS_shutdown+0x14b/0x170
[<ffffffff8100334c>] do_syscall_64+0x19c/0x410
[<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25
Code: 90 00 b4 0b 83 c7 00 f1 f1 f1 f1 4c 8d 6d e0 c7 40 04 00 00 00 f4 c7 40 08 f3 f3 f3 f3 48 89 d8 48 c1 e8 03 c7 45 b4 00 00 00 00 <80> 3c 30 00 75 78 48 8d 7b 08 49 8d 75 c0 48 b8 00 00 00 00 00
RIP [<ffffffff830bb46b>] tipc_node_xmit_skb+0x6b/0x140
RSP <ffff8800595bfce8>
---[ end trace 57b0484e351e71f1 ]---
I feel like we should maybe return -ENOMEM or -ENOBUFS, but I'm not sure
userspace is equipped to handle that. Anyway, this is better than a GPF
and looks somewhat consistent with other tipc_msg_create() callers.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit cf6f7e1d5109 ("tipc: dump monitor attributes"),
I dereferenced a pointer before checking if its valid.
This is reported by static check Smatch as:
net/tipc/monitor.c:733 tipc_nl_add_monitor_peer()
warn: variable dereferenced before check 'mon' (see line 731)
In this commit, we check for a valid monitor before proceeding
with any other operation.
Fixes: cf6f7e1d5109 ("tipc: dump monitor attributes")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the error handling case of nla_nest_start() failed read_unlock_bh()
is called to unlock a lock that had not been taken yet. sparse warns
about the context imbalance as the following:
net/tipc/monitor.c:799:23: warning:
context imbalance in '__tipc_nl_add_monitor' - different lock contexts for basic block
Fixes: cf6f7e1d5109 ('tipc: dump monitor attributes')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
