| Age | Commit message (Collapse) | Author |
|---|
|
This re-introduces the effect of commit a32452366b72 ("vti4:
Don't count header length twice.") which was accidentally
reverted by merge commit f895f0cfbb77 ("Merge branch 'master' of
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec").
The commit message from Steffen Klassert said:
We currently count the size of LL_MAX_HEADER and struct iphdr
twice for vti4 devices, this leads to a wrong device mtu.
The size of LL_MAX_HEADER and struct iphdr is already counted in
ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init().
And this is still the case now: ip_tunnel_bind_dev() already
accounts for the header length of the link layer (not
necessarily LL_MAX_HEADER, if the output device is found), plus
one IP header.
For example, with a vti device on top of veth, with MTU of 1500,
the existing implementation would set the initial vti MTU to
1332, accounting once for LL_MAX_HEADER (128, included in
hard_header_len by vti) and twice for the same IP header (once
from hard_header_len, once from ip_tunnel_bind_dev()).
It should instead be 1480, because ip_tunnel_bind_dev() is able
to figure out that the output device is veth, so no additional
link layer header is attached, and will properly count one
single IP header.
The existing issue had the side effect of avoiding PMTUD for
most xfrm policies, by arbitrarily lowering the initial MTU.
However, the only way to get a consistent PMTU value is to let
the xfrm PMTU discovery do its course, and commit d6af1a31cc72
("vti: Add pmtu handling to vti_xmit.") now takes care of local
delivery cases where the application ignores local socket
notifications.
Fixes: b9959fd3b0fa ("vti: switch to new ip tunnel code")
Fixes: f895f0cfbb77 ("Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Fixes: a9a08845e9ac ("vfs: do bulk POLL* -> EPOLL* replacement")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
when the following command
# tc action replace action skbmod swap mac index 100
is run for the first time, and tcf_skbmod_init() fails to allocate struct
tcf_skbmod_params, tcf_skbmod_cleanup() calls kfree_rcu(NULL), thus
causing the following error:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: __call_rcu+0x23/0x2b0
PGD 8000000034057067 P4D 8000000034057067 PUD 74937067 PMD 0
Oops: 0002 [#1] SMP PTI
Modules linked in: act_skbmod(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec crct10dif_pclmul mbcache jbd2 crc32_pclmul snd_hda_core ghash_clmulni_intel snd_hwdep pcbc snd_seq snd_seq_device snd_pcm aesni_intel snd_timer crypto_simd glue_helper snd cryptd virtio_balloon joydev soundcore pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_console virtio_net virtio_blk ata_piix libata crc32c_intel virtio_pci serio_raw virtio_ring virtio i2c_core floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_skbmod]
CPU: 3 PID: 3144 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__call_rcu+0x23/0x2b0
RSP: 0018:ffffbd2e403e7798 EFLAGS: 00010246
RAX: ffffffffc0872080 RBX: ffff981d34bff780 RCX: 00000000ffffffff
RDX: ffffffff922a5f00 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000021f
R10: 000000003d003000 R11: 0000000000aaaaaa R12: 0000000000000000
R13: ffffffff922a5f00 R14: 0000000000000001 R15: ffff981d3b698c2c
FS: 00007f3678292740(0000) GS:ffff981d3fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000007c57a006 CR4: 00000000001606e0
Call Trace:
__tcf_idr_release+0x79/0xf0
tcf_skbmod_init+0x1d1/0x210 [act_skbmod]
tcf_action_init_1+0x2cc/0x430
tcf_action_init+0xd3/0x1b0
tc_ctl_action+0x18b/0x240
rtnetlink_rcv_msg+0x29c/0x310
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1b9/0x270
? rtnl_calcit.isra.28+0x100/0x100
netlink_rcv_skb+0xd2/0x110
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2cd/0x3c0
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x27a/0x290
? filemap_map_pages+0x34a/0x3a0
? __handle_mm_fault+0xbfd/0xe20
__sys_sendmsg+0x51/0x90
do_syscall_64+0x6e/0x1a0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7f36776a3ba0
RSP: 002b:00007fff4703b618 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fff4703b740 RCX: 00007f36776a3ba0
RDX: 0000000000000000 RSI: 00007fff4703b690 RDI: 0000000000000003
RBP: 000000005aaaba36 R08: 0000000000000002 R09: 0000000000000000
R10: 00007fff4703b0a0 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff4703b754 R14: 0000000000000001 R15: 0000000000669f60
Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
RIP: __call_rcu+0x23/0x2b0 RSP: ffffbd2e403e7798
CR2: 0000000000000008
Fix it in tcf_skbmod_cleanup(), ensuring that kfree_rcu(p, ...) is called
only when p is not NULL.
Fixes: 86da71b57383 ("net_sched: Introduce skbmod action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when the following command
# tc action add action sample rate 100 group 100 index 100
is run for the first time, and psample_group_get(100) fails to create a
new group, tcf_sample_cleanup() calls psample_group_put(NULL), thus
causing the following error:
BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
IP: psample_group_put+0x15/0x71 [psample]
PGD 8000000075775067 P4D 8000000075775067 PUD 7453c067 PMD 0
Oops: 0002 [#1] SMP PTI
Modules linked in: act_sample(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core mbcache jbd2 crct10dif_pclmul snd_hwdep crc32_pclmul snd_seq ghash_clmulni_intel pcbc snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer glue_helper snd cryptd joydev pcspkr i2c_piix4 soundcore virtio_balloon nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_net ata_piix virtio_console virtio_blk libata serio_raw crc32c_intel virtio_pci i2c_core virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_tunnel_key]
CPU: 2 PID: 5740 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:psample_group_put+0x15/0x71 [psample]
RSP: 0018:ffffb8a80032f7d0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000024
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffffffc06d93c0
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044
R10: 00000000bd003000 R11: ffff979fba04aa59 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff979fbba3f22c
FS: 00007f7638112740(0000) GS:ffff979fbfd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000001c CR3: 00000000734ea001 CR4: 00000000001606e0
Call Trace:
__tcf_idr_release+0x79/0xf0
tcf_sample_init+0x125/0x1d0 [act_sample]
tcf_action_init_1+0x2cc/0x430
tcf_action_init+0xd3/0x1b0
tc_ctl_action+0x18b/0x240
rtnetlink_rcv_msg+0x29c/0x310
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1b9/0x270
? rtnl_calcit.isra.28+0x100/0x100
netlink_rcv_skb+0xd2/0x110
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2cd/0x3c0
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x27a/0x290
? filemap_map_pages+0x34a/0x3a0
? __handle_mm_fault+0xbfd/0xe20
__sys_sendmsg+0x51/0x90
do_syscall_64+0x6e/0x1a0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7f7637523ba0
RSP: 002b:00007fff0473ef58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fff0473f080 RCX: 00007f7637523ba0
RDX: 0000000000000000 RSI: 00007fff0473efd0 RDI: 0000000000000003
RBP: 000000005aaaac80 R08: 0000000000000002 R09: 0000000000000000
R10: 00007fff0473e9e0 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff0473f094 R14: 0000000000000001 R15: 0000000000669f60
Code: be 02 00 00 00 48 89 df e8 a9 fe ff ff e9 7c ff ff ff 0f 1f 40 00 0f 1f 44 00 00 53 48 89 fb 48 c7 c7 c0 93 6d c0 e8 db 20 8c ef <83> 6b 1c 01 74 10 48 c7 c7 c0 93 6d c0 ff 14 25 e8 83 83 b0 5b
RIP: psample_group_put+0x15/0x71 [psample] RSP: ffffb8a80032f7d0
CR2: 000000000000001c
Fix it in tcf_sample_cleanup(), ensuring that calls to psample_group_put(p)
are done only when p is not NULL.
Fixes: cadb9c9fdbc6 ("net/sched: act_sample: Fix error path in init")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when the following command
# tc action add action tunnel_key unset index 100
is run for the first time, and tunnel_key_init() fails to allocate struct
tcf_tunnel_key_params, tunnel_key_release() dereferences NULL pointers.
This causes the following error:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: tunnel_key_release+0xd/0x40 [act_tunnel_key]
PGD 8000000033787067 P4D 8000000033787067 PUD 74646067 PMD 0
Oops: 0000 [#1] SMP PTI
Modules linked in: act_tunnel_key(E) act_csum ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 mbcache jbd2 crct10dif_pclmul crc32_pclmul snd_hda_codec_generic ghash_clmulni_intel snd_hda_intel pcbc snd_hda_codec snd_hda_core snd_hwdep snd_seq aesni_intel snd_seq_device crypto_simd glue_helper snd_pcm cryptd joydev snd_timer pcspkr virtio_balloon snd i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_net virtio_blk drm virtio_console crc32c_intel ata_piix serio_raw i2c_core virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod
CPU: 2 PID: 3101 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:tunnel_key_release+0xd/0x40 [act_tunnel_key]
RSP: 0018:ffffba46803b7768 EFLAGS: 00010286
RAX: ffffffffc09010a0 RBX: 0000000000000000 RCX: 0000000000000024
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff99ee336d7480
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044
R10: 0000000000000220 R11: ffff99ee79d73131 R12: 0000000000000000
R13: ffff99ee32d67610 R14: ffff99ee7671dc38 R15: 00000000fffffff4
FS: 00007febcb2cd740(0000) GS:ffff99ee7fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000007c8e4005 CR4: 00000000001606e0
Call Trace:
__tcf_idr_release+0x79/0xf0
tunnel_key_init+0xd9/0x460 [act_tunnel_key]
tcf_action_init_1+0x2cc/0x430
tcf_action_init+0xd3/0x1b0
tc_ctl_action+0x18b/0x240
rtnetlink_rcv_msg+0x29c/0x310
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1b9/0x270
? rtnl_calcit.isra.28+0x100/0x100
netlink_rcv_skb+0xd2/0x110
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2cd/0x3c0
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x27a/0x290
__sys_sendmsg+0x51/0x90
do_syscall_64+0x6e/0x1a0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7febca6deba0
RSP: 002b:00007ffe7b0dd128 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffe7b0dd250 RCX: 00007febca6deba0
RDX: 0000000000000000 RSI: 00007ffe7b0dd1a0 RDI: 0000000000000003
RBP: 000000005aaa90cb R08: 0000000000000002 R09: 0000000000000000
R10: 00007ffe7b0dcba0 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffe7b0dd264 R14: 0000000000000001 R15: 0000000000669f60
Code: 44 00 00 8b 0d b5 23 00 00 48 8b 87 48 10 00 00 48 8b 3c c8 e9 a5 e5 d8 c3 0f 1f 44 00 00 0f 1f 44 00 00 53 48 8b 9f b0 00 00 00 <83> 7b 10 01 74 0b 48 89 df 31 f6 5b e9 f2 fa 7f c3 48 8b 7b 18
RIP: tunnel_key_release+0xd/0x40 [act_tunnel_key] RSP: ffffba46803b7768
CR2: 0000000000000010
Fix this in tunnel_key_release(), ensuring 'param' is not NULL before
dereferencing it.
Fixes: d0f6dd8a914f ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when the following command
# tc action add action csum udp continue index 100
is run for the first time, and tcf_csum_init() fails allocating struct
tcf_csum, tcf_csum_cleanup() calls kfree_rcu(NULL,...). This causes the
following error:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: __call_rcu+0x23/0x2b0
PGD 80000000740b4067 P4D 80000000740b4067 PUD 32e7f067 PMD 0
Oops: 0002 [#1] SMP PTI
Modules linked in: act_csum(E) act_vlan ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 mbcache jbd2 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_generic pcbc snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer aesni_intel crypto_simd glue_helper cryptd snd joydev pcspkr virtio_balloon i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_blk drm virtio_net virtio_console ata_piix crc32c_intel libata virtio_pci serio_raw i2c_core virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_vlan]
CPU: 2 PID: 5763 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__call_rcu+0x23/0x2b0
RSP: 0018:ffffb275803e77c0 EFLAGS: 00010246
RAX: ffffffffc057b080 RBX: ffff9674bc6f5240 RCX: 00000000ffffffff
RDX: ffffffff928a5f00 RSI: 0000000000000008 RDI: 0000000000000008
RBP: 0000000000000008 R08: 0000000000000001 R09: 0000000000000044
R10: 0000000000000220 R11: ffff9674b9ab4821 R12: 0000000000000000
R13: ffffffff928a5f00 R14: 0000000000000000 R15: 0000000000000001
FS: 00007fa6368d8740(0000) GS:ffff9674bfd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 0000000073dec001 CR4: 00000000001606e0
Call Trace:
__tcf_idr_release+0x79/0xf0
tcf_csum_init+0xfb/0x180 [act_csum]
tcf_action_init_1+0x2cc/0x430
tcf_action_init+0xd3/0x1b0
tc_ctl_action+0x18b/0x240
rtnetlink_rcv_msg+0x29c/0x310
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1b9/0x270
? rtnl_calcit.isra.28+0x100/0x100
netlink_rcv_skb+0xd2/0x110
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2cd/0x3c0
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x27a/0x290
? filemap_map_pages+0x34a/0x3a0
? __handle_mm_fault+0xbfd/0xe20
__sys_sendmsg+0x51/0x90
do_syscall_64+0x6e/0x1a0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7fa635ce9ba0
RSP: 002b:00007ffc185b0fc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffc185b10f0 RCX: 00007fa635ce9ba0
RDX: 0000000000000000 RSI: 00007ffc185b1040 RDI: 0000000000000003
RBP: 000000005aaa85e0 R08: 0000000000000002 R09: 0000000000000000
R10: 00007ffc185b0a20 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc185b1104 R14: 0000000000000001 R15: 0000000000669f60
Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
RIP: __call_rcu+0x23/0x2b0 RSP: ffffb275803e77c0
CR2: 0000000000000010
fix this in tcf_csum_cleanup(), ensuring that kfree_rcu(param, ...) is
called only when param is not NULL.
Fixes: 9c5f69bbd75a ("net/sched: act_csum: don't use spinlock in the fast path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when the following command
# tc actions replace action vlan pop index 100
is run for the first time, and tcf_vlan_init() fails allocating struct
tcf_vlan_params, tcf_vlan_cleanup() calls kfree_rcu(NULL, ...). This causes
the following error:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: __call_rcu+0x23/0x2b0
PGD 80000000760a2067 P4D 80000000760a2067 PUD 742c1067 PMD 0
Oops: 0002 [#1] SMP PTI
Modules linked in: act_vlan(E) ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel mbcache snd_hda_codec jbd2 snd_hda_core crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer glue_helper snd cryptd joydev soundcore virtio_balloon pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_console virtio_blk virtio_net ata_piix crc32c_intel libata virtio_pci i2c_core virtio_ring serio_raw virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_vlan]
CPU: 3 PID: 3119 Comm: tc Tainted: G E 4.16.0-rc4.act_vlan.orig+ #403
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__call_rcu+0x23/0x2b0
RSP: 0018:ffffaac3005fb798 EFLAGS: 00010246
RAX: ffffffffc0704080 RBX: ffff97f2b4bbe900 RCX: 00000000ffffffff
RDX: ffffffffabca5f00 RSI: 0000000000000010 RDI: 0000000000000010
RBP: 0000000000000010 R08: 0000000000000001 R09: 0000000000000044
R10: 00000000fd003000 R11: ffff97f2faab5b91 R12: 0000000000000000
R13: ffffffffabca5f00 R14: ffff97f2fb80202c R15: 00000000fffffff4
FS: 00007f68f75b4740(0000) GS:ffff97f2ffd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000018 CR3: 0000000072b52001 CR4: 00000000001606e0
Call Trace:
__tcf_idr_release+0x79/0xf0
tcf_vlan_init+0x168/0x270 [act_vlan]
tcf_action_init_1+0x2cc/0x430
tcf_action_init+0xd3/0x1b0
tc_ctl_action+0x18b/0x240
rtnetlink_rcv_msg+0x29c/0x310
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1b9/0x270
? rtnl_calcit.isra.28+0x100/0x100
netlink_rcv_skb+0xd2/0x110
netlink_unicast+0x17c/0x230
netlink_sendmsg+0x2cd/0x3c0
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x27a/0x290
? filemap_map_pages+0x34a/0x3a0
? __handle_mm_fault+0xbfd/0xe20
__sys_sendmsg+0x51/0x90
do_syscall_64+0x6e/0x1a0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7f68f69c5ba0
RSP: 002b:00007fffd79c1118 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fffd79c1240 RCX: 00007f68f69c5ba0
RDX: 0000000000000000 RSI: 00007fffd79c1190 RDI: 0000000000000003
RBP: 000000005aaa708e R08: 0000000000000002 R09: 0000000000000000
R10: 00007fffd79c0ba0 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffd79c1254 R14: 0000000000000001 R15: 0000000000669f60
Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
RIP: __call_rcu+0x23/0x2b0 RSP: ffffaac3005fb798
CR2: 0000000000000018
fix this in tcf_vlan_cleanup(), ensuring that kfree_rcu(p, ...) is called
only when p is not NULL.
Fixes: 4c5b9d9642c8 ("act_vlan: VLAN action rewrite to use RCU lock/unlock and update")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Manish Kurup <manish.kurup@verizon.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported one use-after-free in pfifo_fast_enqueue() [1]
Issue here is that we can not reuse skb after a successful skb_array_produce()
since another cpu might have consumed it already.
I believe a similar problem exists in try_bulk_dequeue_skb_slow()
in case we put an skb into qdisc_enqueue_skb_bad_txq() for lockless qdisc.
[1]
BUG: KASAN: use-after-free in qdisc_pkt_len include/net/sch_generic.h:610 [inline]
BUG: KASAN: use-after-free in qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
BUG: KASAN: use-after-free in pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
Read of size 4 at addr ffff8801cede37e8 by task syzkaller717588/5543
CPU: 1 PID: 5543 Comm: syzkaller717588 Not tainted 4.16.0-rc4+ #265
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
__asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:432
qdisc_pkt_len include/net/sch_generic.h:610 [inline]
qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
__dev_xmit_skb net/core/dev.c:3216 [inline]
Fixes: c5ad119fb6c0 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+ed43b6903ab968b16f54@syzkaller.appspotmail.com
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checking for 0 is insufficient: when an SKB without a batadv header, but
with a VLAN header is received, hdr_size will be 4, making the following
code interpret the Ethernet header as a batadv header.
Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data
must be (re)set after calling it. The ethhdr variable is dropped
altogether.
Fixes: 7cdcf6dddc42 ("batman-adv: add UNICAST_4ADDR packet type")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
When errors are enqueued to the error queue via sock_queue_err_skb()
function, it is possible that the waiting application is not notified.
Calling 'sk->sk_data_ready()' would not notify applications that
selected only POLLERR events in poll() (for example).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Randy E. Witt <randy.e.witt@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nlmsg_multicast() consumes always the skb, thus the original skb must be
freed only when this function is called with a clone.
Fixes: cb9f7a9a5c96 ("netlink: ensure to loop over all netns in genlmsg_multicast_allns()")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free memory by calling put_device(), if afiucv_iucv_init is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes: ab7ac4eb9832e32a09f4e804 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().
This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.
This patch fixes the behaviour by inserting the inner tag at the right
position.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().
The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.
The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.
In rx path single tag case, it works as follows:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+------+----
| ETH | VLAN | ETH |
| ADDRS | TPID | TCI | TYPE |
+-------------------+-------------+------+----
<-------- mac_len --------->
<------------->
to be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<-------- mac_len --------->
This is ok, but in rx double tag case, it corrupts packets:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+-------------+------+----
| ETH | VLAN | VLAN | ETH |
| ADDRS | TPID | TCI | TPID | TCI | TYPE |
+-------------------+-------------+-------------+------+----
<--------------- mac_len ---------------->
<------------->
should be removed
<--------------------------->
actually will be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<--------------- mac_len ---------------->
So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.
skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.
Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff11170 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the xfrm_local_error, rcu_read_unlock should be called when afinfo
is not NULL. because xfrm_state_get_afinfo calls rcu_read_unlock
if afinfo is NULL.
Fixes: af5d27c4e12b ("xfrm: remove xfrm_state_put_afinfo")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
If set/unset mode of the tunnel_key action is not provided, ->init() still
returns 0, and the caller proceeds with bogus 'struct tc_action *' object,
this results in crash:
% tc actions add action tunnel_key src_ip 1.1.1.1 dst_ip 2.2.2.1 id 7 index 1
[ 35.805515] general protection fault: 0000 [#1] SMP PTI
[ 35.806161] Modules linked in: act_tunnel_key kvm_intel kvm irqbypass
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64
crypto_simd glue_helper cryptd serio_raw
[ 35.808233] CPU: 1 PID: 428 Comm: tc Not tainted 4.16.0-rc4+ #286
[ 35.808929] RIP: 0010:tcf_action_init+0x90/0x190
[ 35.809457] RSP: 0018:ffffb8edc068b9a0 EFLAGS: 00010206
[ 35.810053] RAX: 1320c000000a0003 RBX: 0000000000000001 RCX: 0000000000000000
[ 35.810866] RDX: 0000000000000070 RSI: 0000000000007965 RDI: ffffb8edc068b910
[ 35.811660] RBP: ffffb8edc068b9d0 R08: 0000000000000000 R09: ffffb8edc068b808
[ 35.812463] R10: ffffffffc02bf040 R11: 0000000000000040 R12: ffffb8edc068bb38
[ 35.813235] R13: 0000000000000000 R14: 0000000000000000 R15: ffffb8edc068b910
[ 35.814006] FS: 00007f3d0d8556c0(0000) GS:ffff91d1dbc40000(0000)
knlGS:0000000000000000
[ 35.814881] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 35.815540] CR2: 000000000043f720 CR3: 0000000019248001 CR4: 00000000001606a0
[ 35.816457] Call Trace:
[ 35.817158] tc_ctl_action+0x11a/0x220
[ 35.817795] rtnetlink_rcv_msg+0x23d/0x2e0
[ 35.818457] ? __slab_alloc+0x1c/0x30
[ 35.819079] ? __kmalloc_node_track_caller+0xb1/0x2b0
[ 35.819544] ? rtnl_calcit.isra.30+0xe0/0xe0
[ 35.820231] netlink_rcv_skb+0xce/0x100
[ 35.820744] netlink_unicast+0x164/0x220
[ 35.821500] netlink_sendmsg+0x293/0x370
[ 35.822040] sock_sendmsg+0x30/0x40
[ 35.822508] ___sys_sendmsg+0x2c5/0x2e0
[ 35.823149] ? pagecache_get_page+0x27/0x220
[ 35.823714] ? filemap_fault+0xa2/0x640
[ 35.824423] ? page_add_file_rmap+0x108/0x200
[ 35.825065] ? alloc_set_pte+0x2aa/0x530
[ 35.825585] ? finish_fault+0x4e/0x70
[ 35.826140] ? __handle_mm_fault+0xbc1/0x10d0
[ 35.826723] ? __sys_sendmsg+0x41/0x70
[ 35.827230] __sys_sendmsg+0x41/0x70
[ 35.827710] do_syscall_64+0x68/0x120
[ 35.828195] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[ 35.828859] RIP: 0033:0x7f3d0ca4da67
[ 35.829331] RSP: 002b:00007ffc9f284338 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[ 35.830304] RAX: ffffffffffffffda RBX: 00007ffc9f284460 RCX: 00007f3d0ca4da67
[ 35.831247] RDX: 0000000000000000 RSI: 00007ffc9f2843b0 RDI: 0000000000000003
[ 35.832167] RBP: 000000005aa6a7a9 R08: 0000000000000001 R09: 0000000000000000
[ 35.833075] R10: 00000000000005f1 R11: 0000000000000246 R12: 0000000000000000
[ 35.833997] R13: 00007ffc9f2884c0 R14: 0000000000000001 R15: 0000000000674640
[ 35.834923] Code: 24 30 bb 01 00 00 00 45 31 f6 eb 5e 8b 50 08 83 c2 07 83 e2
fc 83 c2 70 49 8b 07 48 8b 40 70 48 85 c0 74 10 48 89 14 24 4c 89 ff <ff> d0 48
8b 14 24 48 01 c2 49 01 d6 45 85 ed 74 05 41 83 47 2c
[ 35.837442] RIP: tcf_action_init+0x90/0x190 RSP: ffffb8edc068b9a0
[ 35.838291] ---[ end trace a095c06ee4b97a26 ]---
Fixes: d0f6dd8a914f ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Closing of a listen socket wakes up kernel_accept() of
smc_tcp_listen_worker(), and then has to wait till smc_tcp_listen_worker()
gives up the internal clcsock. The wait logic introduced with
commit 127f49705823 ("net/smc: release clcsock from tcp_listen_worker")
might wait longer than necessary. This patch implements the idea to
implement the wait just with flush_work(), and gets rid of the extra
smc_close_wait_listen_clcsock() function.
Fixes: 127f49705823 ("net/smc: release clcsock from tcp_listen_worker")
Reported-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to the rework of PMTU information storage in commit
2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.
Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.
This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().
One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.
Fixes: 2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrei Vagin reported a KASAN: slab-out-of-bounds error in
skb_update_prio()
Since SYNACK might be attached to a request socket, we need to
get back to the listener socket.
Since this listener is manipulated without locks, add const
qualifiers to sock_cgroup_prioidx() so that the const can also
be used in skb_update_prio()
Also add the const qualifier to sock_cgroup_classid() for consistency.
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2018-03-13
1) Refuse to insert 32 bit userspace socket policies on 64
bit systems like we do it for standard policies. We don't
have a compat layer, so inserting socket policies from
32 bit userspace will lead to a broken configuration.
2) Make the policy hold queue work without the flowcache.
Dummy bundles are not chached anymore, so we need to
generate a new one on each lookup as long as the SAs
are not yet in place.
3) Fix the validation of the esn replay attribute. The
The sanity check in verify_replay() is bypassed if
the XFRM_STATE_ESN flag is not set. Fix this by doing
the sanity check uncoditionally.
From Florian Westphal.
4) After most of the dst_entry garbage collection code
is removed, we may leak xfrm_dst entries as they are
neither cached nor tracked somewhere. Fix this by
reusing the 'uncached_list' to track xfrm_dst entries
too. From Xin Long.
5) Fix a rcu_read_lock/rcu_read_unlock imbalance in
xfrm_get_tos() From Xin Long.
6) Fix an infinite loop in xfrm_get_dst_nexthop. On
transport mode we fetch the child dst_entry after
we continue, so this pointer is never updated.
Fix this by fetching it before we continue.
7) Fix ESN sequence number gap after IPsec GSO packets.
We accidentally increment the sequence number counter
on the xfrm_state by one packet too much in the ESN
case. Fix this by setting the sequence number to the
correct value.
8) Reset the ethernet protocol after decapsulation only if a
mac header was set. Otherwise it breaks configurations
with TUN devices. From Yossi Kuperman.
9) Fix __this_cpu_read() usage in preemptible code. Use
this_cpu_read() instead in ipcomp_alloc_tfms().
From Greg Hackmann.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
f7c83bcbfaf5 ("net: xfrm: use __this_cpu_read per-cpu helper") added a
__this_cpu_read() call inside ipcomp_alloc_tfms().
At the time, __this_cpu_read() required the caller to either not care
about races or to handle preemption/interrupt issues. 3.15 tightened
the rules around some per-cpu operations, and now __this_cpu_read()
should never be used in a preemptible context. On 3.15 and later, we
need to use this_cpu_read() instead.
syzkaller reported this leading to the following kernel BUG while
fuzzing sendmsg:
BUG: using __this_cpu_read() in preemptible [00000000] code: repro/3101
caller is ipcomp_init_state+0x185/0x990
CPU: 3 PID: 3101 Comm: repro Not tainted 4.16.0-rc4-00123-g86f84779d8e9 #154
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0xb9/0x115
check_preemption_disabled+0x1cb/0x1f0
ipcomp_init_state+0x185/0x990
? __xfrm_init_state+0x876/0xc20
? lock_downgrade+0x5e0/0x5e0
ipcomp4_init_state+0xaa/0x7c0
__xfrm_init_state+0x3eb/0xc20
xfrm_init_state+0x19/0x60
pfkey_add+0x20df/0x36f0
? pfkey_broadcast+0x3dd/0x600
? pfkey_sock_destruct+0x340/0x340
? pfkey_seq_stop+0x80/0x80
? __skb_clone+0x236/0x750
? kmem_cache_alloc+0x1f6/0x260
? pfkey_sock_destruct+0x340/0x340
? pfkey_process+0x62a/0x6f0
pfkey_process+0x62a/0x6f0
? pfkey_send_new_mapping+0x11c0/0x11c0
? mutex_lock_io_nested+0x1390/0x1390
pfkey_sendmsg+0x383/0x750
? dump_sp+0x430/0x430
sock_sendmsg+0xc0/0x100
___sys_sendmsg+0x6c8/0x8b0
? copy_msghdr_from_user+0x3b0/0x3b0
? pagevec_lru_move_fn+0x144/0x1f0
? find_held_lock+0x32/0x1c0
? do_huge_pmd_anonymous_page+0xc43/0x11e0
? lock_downgrade+0x5e0/0x5e0
? get_kernel_page+0xb0/0xb0
? _raw_spin_unlock+0x29/0x40
? do_huge_pmd_anonymous_page+0x400/0x11e0
? __handle_mm_fault+0x553/0x2460
? __fget_light+0x163/0x1f0
? __sys_sendmsg+0xc7/0x170
__sys_sendmsg+0xc7/0x170
? SyS_shutdown+0x1a0/0x1a0
? __do_page_fault+0x5a0/0xca0
? lock_downgrade+0x5e0/0x5e0
SyS_sendmsg+0x27/0x40
? __sys_sendmsg+0x170/0x170
do_syscall_64+0x19f/0x640
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x7f0ee73dfb79
RSP: 002b:00007ffe14fc15a8 EFLAGS: 00000207 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f0ee73dfb79
RDX: 0000000000000000 RSI: 00000000208befc8 RDI: 0000000000000004
RBP: 00007ffe14fc15b0 R08: 00007ffe14fc15c0 R09: 00007ffe14fc15c0
R10: 0000000000000000 R11: 0000000000000207 R12: 0000000000400440
R13: 00007ffe14fc16b0 R14: 0000000000000000 R15: 0000000000000000
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
During the conversion to dsa_is_user_port(), a condition ended up being
reversed, which would prevent the creation of any user port when using
the legacy binding and/or platform data, fix that.
Fixes: 4a5b85ffe2a0 ("net: dsa: use dsa_is_user_port everywhere")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The l2tp_tunnel_create() function checks for v4mapped ipv6
sockets and cache that flag, so that l2tp core code can
reusing it at xmit time.
If the socket is provided by the userspace, the connection
status of the tunnel sockets can change between the tunnel
creation and the xmit call, so that syzbot is able to
trigger the following splat:
BUG: KASAN: use-after-free in ip6_dst_idev include/net/ip6_fib.h:192
[inline]
BUG: KASAN: use-after-free in ip6_xmit+0x1f76/0x2260
net/ipv6/ip6_output.c:264
Read of size 8 at addr ffff8801bd949318 by task syz-executor4/23448
CPU: 0 PID: 23448 Comm: syz-executor4 Not tainted 4.16.0-rc4+ #65
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
ip6_dst_idev include/net/ip6_fib.h:192 [inline]
ip6_xmit+0x1f76/0x2260 net/ipv6/ip6_output.c:264
inet6_csk_xmit+0x2fc/0x580 net/ipv6/inet6_connection_sock.c:139
l2tp_xmit_core net/l2tp/l2tp_core.c:1053 [inline]
l2tp_xmit_skb+0x105f/0x1410 net/l2tp/l2tp_core.c:1148
pppol2tp_sendmsg+0x470/0x670 net/l2tp/l2tp_ppp.c:341
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
___sys_sendmsg+0x767/0x8b0 net/socket.c:2046
__sys_sendmsg+0xe5/0x210 net/socket.c:2080
SYSC_sendmsg net/socket.c:2091 [inline]
SyS_sendmsg+0x2d/0x50 net/socket.c:2087
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x453e69
RSP: 002b:00007f819593cc68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f819593d6d4 RCX: 0000000000453e69
RDX: 0000000000000081 RSI: 000000002037ffc8 RDI: 0000000000000004
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000004c3 R14: 00000000006f72e8 R15: 0000000000000000
This change addresses the issues:
* explicitly checking for TCP_ESTABLISHED for user space provided sockets
* dropping the v4mapped flag usage - it can become outdated - and
explicitly invoking ipv6_addr_v4mapped() instead
The issue is apparently there since ancient times.
v1 -> v2: (many thanks to Guillaume)
- with csum issue introduced in v1
- replace pr_err with pr_debug
- fix build issue with IPV6 disabled
- move l2tp_sk_is_v4mapped in l2tp_core.c
v2 -> v3:
- don't update inet_daddr for v4mapped address, unneeded
- drop rendundant check at creation time
Reported-and-tested-by: syzbot+92fa328176eb07e4ac1a@syzkaller.appspotmail.com
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On unsuccesful ip6_datagram_connect(), if the failure is caused by
ip6_datagram_dst_update(), the sk peer information are cleared, but
the sk->sk_state is preserved.
If the socket was already in an established status, the overall sk
status is inconsistent and fouls later checks in datagram code.
Fix this saving the old peer information and restoring them in
case of failure. This also aligns ipv6 datagram connect() behavior
with ipv4.
v1 -> v2:
- added missing Fixes tag
Fixes: 85cb73ff9b74 ("net: ipv6: reset daddr and dport in sk if connect() fails")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree, they are:
1) Fixed hashtable representation doesn't support timeout flag, skip it
otherwise rules to add elements from the packet fail bogusly fail with
EOPNOTSUPP.
2) Fix bogus error with 32-bits ebtables userspace and 64-bits kernel,
patch from Florian Westphal.
3) Sanitize proc names in several x_tables extensions, also from Florian.
4) Add sanitization to ebt_among wormhash logic, from Florian.
5) Missing release of hook array in flowtable.
====================
|
|
registered
Now when using 'ss' in iproute, kernel would try to load all _diag
modules, which also causes corresponding family and proto modules
to be loaded as well due to module dependencies.
Like after running 'ss', sctp, dccp, af_packet (if it works as a module)
would be loaded.
For example:
$ lsmod|grep sctp
$ ss
$ lsmod|grep sctp
sctp_diag 16384 0
sctp 323584 5 sctp_diag
inet_diag 24576 4 raw_diag,tcp_diag,sctp_diag,udp_diag
libcrc32c 16384 3 nf_conntrack,nf_nat,sctp
As these family and proto modules are loaded unintentionally, it
could cause some problems, like:
- Some debug tools use 'ss' to collect the socket info, which loads all
those diag and family and protocol modules. It's noisy for identifying
issues.
- Users usually expect to drop sctp init packet silently when they
have no sense of sctp protocol instead of sending abort back.
- It wastes resources (especially with multiple netns), and SCTP module
can't be unloaded once it's loaded.
...
In short, it's really inappropriate to have these family and proto
modules loaded unexpectedly when just doing debugging with inet_diag.
This patch is to introduce sock_load_diag_module() where it loads
the _diag module only when it's corresponding family or proto has
been already registered.
Note that we can't just load _diag module without the family or
proto loaded, as some symbols used in _diag module are from the
family or proto module.
v1->v2:
- move inet proto check to inet_diag to avoid a compiling err.
v2->v3:
- define sock_load_diag_module in sock.c and export one symbol
only.
- improve the changelog.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Max delat_t should be the full_bucket/rate instead of the full_bucket.
Also report EINVAL if the rate is zero.
Fixes: 96fbc13d7e77 ("openvswitch: Add meter infrastructure")
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: zhangliping <zhangliping02@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we leak this array.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823edf ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
Tested with same rules from the earlier patch.
Fixes: c4585a2823edf ("bridge: ebt_among: add missing match size checks")
Reported-by: <syzbot+bdabab6f1983a03fc009@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
recent and hashlimit both create /proc files, but only check that
name is 0 terminated.
This can trigger WARN() from procfs when name is "" or "/".
Add helper for this and then use it for both.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: <syzbot+0502b00edac2a0680b61@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.
Fixes: b71812168571fa ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The patch adds skb_cow_header() to ensure enough headroom
at ip6erspan_tunnel_xmit before pushing the erspan header
to the skb.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When users fill in incorrect erspan version number through
the struct erspan_metadata uapi, current code skips pushing
the erspan header but continue pushing the gre header, which
is incorrect. The patch fixes it by returning error.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds the erspan v2 proto in ip6gre_tunnel_lookup
so the erspan v2 tunnel can be found correctly.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As well as the basic conversion, I noticed that a lot of the
SCTP code checks gso_type without first checking skb_is_gso()
so I have added that where appropriate.
Also, document the helper.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A tun device type can trivially be set to arbitrary value using
TUNSETLINK ioctl().
Therefore, lowpan_device_event() must really check that ieee802154_ptr
is not NULL.
Fixes: 2c88b5283f60d ("ieee802154: 6lowpan: remove check on null")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following slab-out-of-bounds kasan report in
ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not
linear and the accessed data are not in the linear data region of orig_skb.
[ 1503.122508] ==================================================================
[ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990
[ 1503.123036] Read of size 1184 at addr ffff8800298ab6b0 by task netperf/1932
[ 1503.123220] CPU: 0 PID: 1932 Comm: netperf Not tainted 4.16.0-rc2+ #124
[ 1503.123347] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-2.fc27 04/01/2014
[ 1503.123527] Call Trace:
[ 1503.123579] <IRQ>
[ 1503.123638] print_address_description+0x6e/0x280
[ 1503.123849] kasan_report+0x233/0x350
[ 1503.123946] memcpy+0x1f/0x50
[ 1503.124037] ndisc_send_redirect+0x94e/0x990
[ 1503.125150] ip6_forward+0x1242/0x13b0
[...]
[ 1503.153890] Allocated by task 1932:
[ 1503.153982] kasan_kmalloc+0x9f/0xd0
[ 1503.154074] __kmalloc_track_caller+0xb5/0x160
[ 1503.154198] __kmalloc_reserve.isra.41+0x24/0x70
[ 1503.154324] __alloc_skb+0x130/0x3e0
[ 1503.154415] sctp_packet_transmit+0x21a/0x1810
[ 1503.154533] sctp_outq_flush+0xc14/0x1db0
[ 1503.154624] sctp_do_sm+0x34e/0x2740
[ 1503.154715] sctp_primitive_SEND+0x57/0x70
[ 1503.154807] sctp_sendmsg+0xaa6/0x1b10
[ 1503.154897] sock_sendmsg+0x68/0x80
[ 1503.154987] ___sys_sendmsg+0x431/0x4b0
[ 1503.155078] __sys_sendmsg+0xa4/0x130
[ 1503.155168] do_syscall_64+0x171/0x3f0
[ 1503.155259] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 1503.155436] Freed by task 1932:
[ 1503.155527] __kasan_slab_free+0x134/0x180
[ 1503.155618] kfree+0xbc/0x180
[ 1503.155709] skb_release_data+0x27f/0x2c0
[ 1503.155800] consume_skb+0x94/0xe0
[ 1503.155889] sctp_chunk_put+0x1aa/0x1f0
[ 1503.155979] sctp_inq_pop+0x2f8/0x6e0
[ 1503.156070] sctp_assoc_bh_rcv+0x6a/0x230
[ 1503.156164] sctp_inq_push+0x117/0x150
[ 1503.156255] sctp_backlog_rcv+0xdf/0x4a0
[ 1503.156346] __release_sock+0x142/0x250
[ 1503.156436] release_sock+0x80/0x180
[ 1503.156526] sctp_sendmsg+0xbb0/0x1b10
[ 1503.156617] sock_sendmsg+0x68/0x80
[ 1503.156708] ___sys_sendmsg+0x431/0x4b0
[ 1503.156799] __sys_sendmsg+0xa4/0x130
[ 1503.156889] do_syscall_64+0x171/0x3f0
[ 1503.156980] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 1503.157158] The buggy address belongs to the object at ffff8800298ab600
which belongs to the cache kmalloc-1024 of size 1024
[ 1503.157444] The buggy address is located 176 bytes inside of
1024-byte region [ffff8800298ab600, ffff8800298aba00)
[ 1503.157702] The buggy address belongs to the page:
[ 1503.157820] page:ffffea0000a62a00 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 1503.158053] flags: 0x4000000000008100(slab|head)
[ 1503.158171] raw: 4000000000008100 0000000000000000 0000000000000000 00000001800e000e
[ 1503.158350] raw: dead000000000100 dead000000000200 ffff880036002600 0000000000000000
[ 1503.158523] page dumped because: kasan: bad access detected
[ 1503.158698] Memory state around the buggy address:
[ 1503.158816] ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.158988] ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.159165] >ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1503.159338] ^
[ 1503.159436] ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159610] ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159785] ==================================================================
[ 1503.159964] Disabling lock debugging due to kernel taint
The test scenario to trigger the issue consists of 4 devices:
- H0: data sender, connected to LAN0
- H1: data receiver, connected to LAN1
- GW0 and GW1: routers between LAN0 and LAN1. Both of them have an
ethernet connection on LAN0 and LAN1
On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for
data from LAN0 to LAN1.
Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent
data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send
buffer size is set to 16K). While data streams are active flush the route
cache on HA multiple times.
I have not been able to identify a given commit that introduced the issue
since, using the reproducer described above, the kasan report has been
triggered from 4.14 and I have not gone back further.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-03-08
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix various BPF helpers which adjust the skb and its GSO information
with regards to SCTP GSO. The latter is a special case where gso_size
is of value GSO_BY_FRAGS, so mangling that will end up corrupting
the skb, thus bail out when seeing SCTP GSO packets, from Daniel(s).
2) Fix a compilation error in bpftool where BPF_FS_MAGIC is not defined
due to too old kernel headers in the system, from Jiri.
3) Increase the number of x64 JIT passes in order to allow larger images
to converge instead of punting them to interpreter or having them
rejected when the interpreter is not built into the kernel, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with v4.16-rc1 we've been seeing a higher than usual number
of requests for the kernel to load networking modules, even on events
which shouldn't trigger a module load (e.g. ioctl(TCGETS)). Stephen
Smalley suggested the problem may lie in commit 44c02a2c3dc5
("dev_ioctl(): move copyin/copyout to callers") which moves changes
the network dev_ioctl() function to always call dev_load(),
regardless of the requested ioctl.
This patch moves the dev_load() calls back into the individual ioctls
while preserving the rest of the original patch.
Reported-by: Dominick Grift <dac.override@gmail.com>
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.
Similar to a27fd7a8ed38 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.
Fixes: f214f915e7db ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL,
therefore if DCCP socket is disconnected and dccp_sendmsg() is
called after it, it will cause a NULL pointer dereference in
dccp_write_xmit().
This crash and the reproducer was reported by syzbot. Looks like
it is reproduced if commit 69c64866ce07 ("dccp: CVE-2017-8824:
use-after-free in DCCP code") is applied.
Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller found an issue caused by lack of sufficient checks
in l2tp_tunnel_create()
RAW sockets can not be considered as UDP ones for instance.
In another patch, we shall replace all pr_err() by less intrusive
pr_debug() so that syzkaller can find other bugs faster.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
==================================================================
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
dst_release: dst:00000000d53d0d0f refcnt:-1
Write of size 1 at addr ffff8801d013b798 by task syz-executor3/6242
CPU: 1 PID: 6242 Comm: syz-executor3 Not tainted 4.16.0-rc2+ #253
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23b/0x360 mm/kasan/report.c:412
__asan_report_store1_noabort+0x17/0x20 mm/kasan/report.c:435
setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
l2tp_tunnel_create+0x1354/0x17f0 net/l2tp/l2tp_core.c:1596
pppol2tp_connect+0x14b1/0x1dd0 net/l2tp/l2tp_ppp.c:707
SYSC_connect+0x213/0x4a0 net/socket.c:1640
SyS_connect+0x24/0x30 net/socket.c:1621
do_syscall_64+0x280/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_evict_bucket() iterates global list, and
several tasks may call it in parallel. All of
them hash the same fq->list_evictor to different
lists, which leads to list corruption.
This patch makes fq be hashed to expired list
only if this has not been made yet by another
task. Since inet_frag_alloc() allocates fq
using kmem_cache_zalloc(), we may rely on
list_evictor is initially unhashed.
The problem seems to exist before async
pernet_operations, as there was possible to have
exit method to be executed in parallel with
inet_frags::frags_work, so I add two Fixes tags.
This also may go to stable.
Fixes: d1fe19444d82 "inet: frag: don't re-use chainlist for evictor"
Fixes: f84c6821aa54 "net: Convert pernet_subsys, registered from inet_init()"
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, administrative MTU changes on a given netdevice are
not reflected on route exceptions for MTU-less routes, with a
set PMTU value, for that device:
# ip -6 route get 2001:db8::b
2001:db8::b from :: dev vti_a proto kernel src 2001:db8::a metric 256 pref medium
# ping6 -c 1 -q -s10000 2001:db8::b > /dev/null
# ip netns exec a ip -6 route get 2001:db8::b
2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
cache expires 571sec mtu 4926 pref medium
# ip link set dev vti_a mtu 3000
# ip -6 route get 2001:db8::b
2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
cache expires 571sec mtu 4926 pref medium
# ip link set dev vti_a mtu 9000
# ip -6 route get 2001:db8::b
2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
cache expires 571sec mtu 4926 pref medium
The first issue is that since commit fb56be83e43d ("net-ipv6: on
device mtu change do not add mtu to mtu-less routes") we don't
call rt6_exceptions_update_pmtu() from rt6_mtu_change_route(),
which handles administrative MTU changes, if the regular route
is MTU-less.
However, PMTU exceptions should be always updated, as long as
RTAX_MTU is not locked. Keep the check for MTU-less main route,
as introduced by that commit, but, for exceptions,
call rt6_exceptions_update_pmtu() regardless of that check.
Once that is fixed, one problem remains: MTU changes are not
reflected if the new MTU is higher than the previous one,
because rt6_exceptions_update_pmtu() doesn't allow that. We
should instead allow PMTU increase if the old PMTU matches the
local MTU, as that implies that the old MTU was the lowest in the
path, and PMTU discovery might lead to different results.
The existing check in rt6_mtu_change_route() correctly took that
case into account (for regular routes only), so factor it out
and re-use it also in rt6_exceptions_update_pmtu().
While at it, fix comments style and grammar, and try to be a bit
more descriptive.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: fb56be83e43d ("net-ipv6: on device mtu change do not add mtu to mtu-less routes")
Fixes: f5bbe7ee79c2 ("ipv6: prepare rt6_mtu_change() for exception table")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we exceed current packets limit and we have more than one
segment in the list returned by skb_gso_segment(), netem drops
only the first one, skipping the rest, hence kmemleak reports:
unreferenced object 0xffff880b5d23b600 (size 1024):
comm "softirq", pid 0, jiffies 4384527763 (age 2770.629s)
hex dump (first 32 bytes):
00 80 23 5d 0b 88 ff ff 00 00 00 00 00 00 00 00 ..#]............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000d8a19b9d>] __alloc_skb+0xc9/0x520
[<000000001709b32f>] skb_segment+0x8c8/0x3710
[<00000000c7b9bb88>] tcp_gso_segment+0x331/0x1830
[<00000000c921cba1>] inet_gso_segment+0x476/0x1370
[<000000008b762dd4>] skb_mac_gso_segment+0x1f9/0x510
[<000000002182660a>] __skb_gso_segment+0x1dd/0x620
[<00000000412651b9>] netem_enqueue+0x1536/0x2590 [sch_netem]
[<0000000005d3b2a9>] __dev_queue_xmit+0x1167/0x2120
[<00000000fc5f7327>] ip_finish_output2+0x998/0xf00
[<00000000d309e9d3>] ip_output+0x1aa/0x2c0
[<000000007ecbd3a4>] tcp_transmit_skb+0x18db/0x3670
[<0000000042d2a45f>] tcp_write_xmit+0x4d4/0x58c0
[<0000000056a44199>] tcp_tasklet_func+0x3d9/0x540
[<0000000013d06d02>] tasklet_action+0x1ca/0x250
[<00000000fcde0b8b>] __do_softirq+0x1b4/0x5a3
[<00000000e7ed027c>] irq_exit+0x1e2/0x210
Fix it by adding the rest of the segments, if any, to skb 'to_free'
list. Add new __qdisc_drop_all() and qdisc_drop_all() functions
because they can be useful in the future if we need to drop segmented
GSO packets in other places.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2018-03-05
Here are a few more Bluetooth fixes for the 4.16 kernel:
- btusb: reset/resume fixes for Yoga 920 and Dell OptiPlex 3060
- Fix for missing encryption refresh with the Security Manager protocol
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Artem Savkov reported that commit 5efec5c655dd leads to a packet loss under
IPSec configuration. It appears that his setup consists of a TUN device,
which does not have a MAC header.
Make sure MAC header exists.
Note: TUN device sets a MAC header pointer, although it does not have one.
Fixes: 5efec5c655dd ("xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version")
Reported-by: Artem Savkov <artem.savkov@gmail.com>
Tested-by: Artem Savkov <artem.savkov@gmail.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
