| Age | Commit message (Collapse) | Author |
|---|
|
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some actions like the police action are stateful and could share state
between devices. This is incompatible with offloading to multiple devices
and drivers might want to test for shared blocks when offloading.
Store a pointer to the tcf_block structure in the tc_cls_common_offload
structure to allow drivers to determine when offloads apply to a shared
block.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the stats_update callback for the police action that
will be used by drivers for hardware offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new command for matchall classifiers that allows hardware
to update statistics.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add police action to the hardware intermediate representation which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move tcf_police_params, tcf_police and tc_police_compat structures to a
header. Making them usable to other code for example drivers that would
offload police actions to hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup unused functions and variables after porting to the newer
intermediate representation.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extends matchall offload to make use of the hardware intermediate
representation. More specifically, this patch moves the native TC
actions in cls_matchall offload to the newer flow_action
representation. This ultimately allows us to avoid a direct
dependency on native TC actions for matchall.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add sample action to the hardware intermediate representation model which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
===================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next, they are:
1) Move nft_expr_clone() to nft_dynset, from Paul Gortmaker.
2) Do not include module.h from net/netfilter/nf_tables.h,
also from Paul.
3) Restrict conntrack sysctl entries to boolean, from Tonghao Zhang.
4) Several patches to add infrastructure to autoload NAT helper
modules from their respective conntrack helper, this also includes
the first client of this code in OVS, patches from Flavio Leitner.
5) Add support to match for conntrack ID, from Brett Mastbergen.
6) Spelling fix in connlabel, from Colin Ian King.
7) Use struct_size() from hashlimit, from Gustavo A. R. Silva.
8) Add optimized version of nf_inet_addr_mask(), from Li RongQing.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(struct xt_hashlimit_htable) + sizeof(struct hlist_head) * size
with:
struct_size(hinfo, hash, size)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
rhashtable_insert_fast() may return an error value when memory
allocation fails, but flow_offload_add() does not check for errors.
This patch just adds missing error checking.
Fixes: ac2a66665e23 ("netfilter: add generic flow table infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Following splat gets triggered when nfnetlink monitor is running while
xtables-nft selftests are running:
net/netfilter/nf_tables_api.c:1272 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
1 lock held by xtables-nft-mul/27006:
#0: 00000000e0f85be9 (&net->nft.commit_mutex){+.+.}, at: nf_tables_valid_genid+0x1a/0x50
Call Trace:
nf_tables_fill_chain_info.isra.45+0x6cc/0x6e0
nf_tables_chain_notify+0xf8/0x1a0
nf_tables_commit+0x165c/0x1740
nf_tables_fill_chain_info() can be called both from dumps (rcu read locked)
or from the transaction path if a userspace process subscribed to nftables
notifications.
In the 'table dump' case, rcu_access_pointer() cannot be used: We do not
hold transaction mutex so the pointer can be NULLed right after the check.
Just unconditionally fetch the value, then have the helper return
immediately if its NULL.
In the notification case we don't hold the rcu read lock, but updates are
prevented due to transaction mutex. Use rcu_dereference_check() to make lockdep
aware of this.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since commit bc7d811ace4a ("netfilter: nf_ct_h323: Convert
CHECK_BOUND macro to function"), NAT traversal for H.323
doesn't work, failing to parse H323-UserInformation.
nf_h323_error_boundary() compares contents of the bitstring,
not the addresses, preventing valid H.323 packets from being
conntrack'd.
This looks like an oversight from when CHECK_BOUND macro was
converted to a function.
To fix it, stop dereferencing bs->cur and bs->end.
Fixes: bc7d811ace4a ("netfilter: nf_ct_h323: Convert CHECK_BOUND macro to function")
Signed-off-by: Jakub Jankowski <shasta@toxcorp.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-05-05
Here's one more bluetooth-next pull request for 5.2:
- Fixed Command Complete event handling check for matching opcode
- Added support for Qualcomm WCN3998 controller, along with DT bindings
- Added default address for Broadcom BCM2076B1 controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids an indirect call per {send,recv}msg syscall in
the common (IPv6 or IPv4 socket) case.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that we avoid another indirect call per RX packet, if
early demux is enabled.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that we avoid another indirect call per RX packet in the common
case.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids an indirect call per RX IPv6/IPv4 packet.
Note that we don't want to use the indirect calls helper for taps.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The code works fine but the problem is that check for negatives is a
no-op:
if (arg < 0)
i = 0;
The "i" value isn't used. We immediately overwrite it with:
i = array_index_nospec(arg, MAX_LEC_ITF);
The array_index_nospec() macro returns zero if "arg" is out of bounds so
this works, but the dead code is confusing and it doesn't look very
intentional.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a pr_warn warning. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a cgroup classifier is added, there is a small time interval in
which tp->root is NULL. If we receive a packet in this small time slice
a NULL pointer dereference will happen, leading to a kernel panic:
# mkdir /sys/fs/cgroup/net_cls/0
# echo 0x100001 > /sys/fs/cgroup/net_cls/0/net_cls.classid
# echo $$ >/sys/fs/cgroup/net_cls/0/tasks
# ping -qfb 255.255.255.255 -I eth0 &>/dev/null &
# tc qdisc add dev eth0 root handle 10: htb
# while : ; do
> tc filter add dev eth0 parent 10: protocol ip prio 10 handle 1: cgroup
> tc filter delete dev eth0
> done
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000028
Mem abort info:
ESR = 0x96000005
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000005
CM = 0, WnR = 0
user pgtable: 4k pages, 39-bit VAs, pgdp = 0000000098a7ff91
[0000000000000028] pgd=0000000000000000, pud=0000000000000000
Internal error: Oops: 96000005 [#1] SMP
Modules linked in: sch_htb cls_cgroup algif_hash af_alg nls_iso8859_1 nls_cp437 vfat fat xhci_plat_hcd m25p80 spi_nor xhci_hcd mtd usbcore usb_common spi_orion sfp i2c_mv64xxx phy_generic mdio_i2c marvell10g i2c_core mvpp2 mvmdio phylink sbsa_gwdt ip_tables x_tables autofs4
Process ping (pid: 5421, stack limit = 0x00000000b20b1505)
CPU: 3 PID: 5421 Comm: ping Not tainted 5.1.0-rc6 #31
Hardware name: Marvell 8040 MACCHIATOBin Double-shot (DT)
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : cls_cgroup_classify+0x80/0xec [cls_cgroup]
lr : cls_cgroup_classify+0x34/0xec [cls_cgroup]
sp : ffffff8012e6b850
x29: ffffff8012e6b850 x28: ffffffc423dd3c00
x27: ffffff801093ebc0 x26: ffffffc425a85b00
x25: 0000000020000000 x24: 0000000000000000
x23: ffffff8012e6b910 x22: ffffffc428db4900
x21: ffffff8012e6b910 x20: 0000000000100001
x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 000000000000001c
x11: 0000000000000018 x10: ffffff8012e6b840
x9 : 0000000000003580 x8 : 000000000000009d
x7 : 0000000000000002 x6 : ffffff8012e6b860
x5 : 000000007cd66ffe x4 : 000000009742a193
x3 : ffffff800865b4d8 x2 : ffffff8012e6b910
x1 : 0000000000000400 x0 : ffffffc42c38f300
Call trace:
cls_cgroup_classify+0x80/0xec [cls_cgroup]
tcf_classify+0x78/0x138
htb_enqueue+0x74/0x320 [sch_htb]
__dev_queue_xmit+0x3e4/0x9d0
dev_queue_xmit+0x24/0x30
ip_finish_output2+0x2e4/0x4d0
ip_finish_output+0x1d8/0x270
ip_mc_output+0xa8/0x240
ip_local_out+0x58/0x68
ip_send_skb+0x2c/0x88
ip_push_pending_frames+0x44/0x50
raw_sendmsg+0x458/0x830
inet_sendmsg+0x54/0xe8
sock_sendmsg+0x34/0x50
__sys_sendto+0xd0/0x120
__arm64_sys_sendto+0x30/0x40
el0_svc_common.constprop.0+0x88/0xf8
el0_svc_handler+0x2c/0x38
el0_svc+0x8/0xc
Code: 39496001 360002a1 b9425c14 34000274 (79405260)
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to nla_nest_start_noflag can return null in the unlikely
event that nla_put returns -EMSGSIZE. Check for this condition to
avoid a null pointer dereference on pointer nla_reply.
Addresses-Coverity: ("Dereference null return value")
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the cached routes, make IPv4 exceptions accessible when
using an IPv6 nexthop struct with IPv4 routes. Simplify the exception
functions by passing in fib_nh_common since that is all it needs,
and then cleanup the call sites that have extraneous fib_nh conversions.
As with the cached routes this is a change in location only, from fib_nh
up to fib_nh_common; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the cached routes are in fib_nh_common, pass it to
rt_cache_route and simplify its callers. For rt_set_nexthop,
the tclassid becomes the last user of fib_nh so move the
container_of under the #ifdef CONFIG_IP_ROUTE_CLASSID.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the cached routes, nh_pcpu_rth_output and nh_rth_input, are IPv4
specific, a later patch wants to make them accessible for IPv6 nexthops
with IPv4 routes using a fib6_nh. Move the cached routes from fib_nh to
fib_nh_common and update references.
Initialization of the cached entries is moved to fib_nh_common_init,
and free is moved to fib_nh_common_release.
Change in location only, from fib_nh up to fib_nh_common; no functional
change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
e is the counter used to save the location of a dump when an
skb is filled. Once the walk of the table is complete, mr_table_dump
needs to return without resetting that index to 0. Dump of a specific
table is looping because of the reset because there is no way to
indicate the walk of the table is done.
Move the reset to the caller so the dump of each table starts at 0,
but the loop counter is maintained if a dump fills an skb.
Fixes: e1cedae1ba6b0 ("ipmr: Refactor mr_rtm_dumproute")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For all other error cases in queue_userspace_packet() the error is
returned, so it makes sense to do the same for these two error cases.
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike do requests, dump genetlink requests now perform strict validation
by default even if the genetlink family does not set policy and maxtype
because it does validation and parsing on its own (e.g. because it wants to
allow different message format for different commands). While the null
policy will be ignored, maxtype (which would be zero) is still checked so
that any attribute will fail validation.
The solution is to only call __nla_validate() from genl_family_rcv_msg()
if family->maxtype is set.
Fixes: ef6243acb478 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d68 ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a matchall classifier is added, there is a small time interval in
which tp->root is NULL. If we receive a packet in this small time slice
a NULL pointer dereference will happen, leading to a kernel panic:
# tc qdisc replace dev eth0 ingress
# tc filter add dev eth0 parent ffff: matchall action gact drop
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000034
Mem abort info:
ESR = 0x96000005
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000005
CM = 0, WnR = 0
user pgtable: 4k pages, 39-bit VAs, pgdp = 00000000a623d530
[0000000000000034] pgd=0000000000000000, pud=0000000000000000
Internal error: Oops: 96000005 [#1] SMP
Modules linked in: cls_matchall sch_ingress nls_iso8859_1 nls_cp437 vfat fat m25p80 spi_nor mtd xhci_plat_hcd xhci_hcd phy_generic sfp mdio_i2c usbcore i2c_mv64xxx marvell10g mvpp2 usb_common spi_orion mvmdio i2c_core sbsa_gwdt phylink ip_tables x_tables autofs4
Process ksoftirqd/0 (pid: 9, stack limit = 0x0000000009de7d62)
CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 5.1.0-rc6 #21
Hardware name: Marvell 8040 MACCHIATOBin Double-shot (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : mall_classify+0x28/0x78 [cls_matchall]
lr : tcf_classify+0x78/0x138
sp : ffffff80109db9d0
x29: ffffff80109db9d0 x28: ffffffc426058800
x27: 0000000000000000 x26: ffffffc425b0dd00
x25: 0000000020000000 x24: 0000000000000000
x23: ffffff80109dbac0 x22: 0000000000000001
x21: ffffffc428ab5100 x20: ffffffc425b0dd00
x19: ffffff80109dbac0 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: ffffffbf108ad288 x12: dead000000000200
x11: 00000000f0000000 x10: 0000000000000001
x9 : ffffffbf1089a220 x8 : 0000000000000001
x7 : ffffffbebffaa950 x6 : 0000000000000000
x5 : 000000442d6ba000 x4 : 0000000000000000
x3 : ffffff8008735ad8 x2 : ffffff80109dbac0
x1 : ffffffc425b0dd00 x0 : ffffff8010592078
Call trace:
mall_classify+0x28/0x78 [cls_matchall]
tcf_classify+0x78/0x138
__netif_receive_skb_core+0x29c/0xa20
__netif_receive_skb_one_core+0x34/0x60
__netif_receive_skb+0x28/0x78
netif_receive_skb_internal+0x2c/0xc0
napi_gro_receive+0x1a0/0x1d8
mvpp2_poll+0x928/0xb18 [mvpp2]
net_rx_action+0x108/0x378
__do_softirq+0x128/0x320
run_ksoftirqd+0x44/0x60
smpboot_thread_fn+0x168/0x1b0
kthread+0x12c/0x130
ret_from_fork+0x10/0x1c
Code: aa0203f3 aa1e03e0 d503201f f9400684 (b9403480)
---[ end trace fc71e2ef7b8ab5a5 ]---
Kernel panic - not syncing: Fatal exception in interrupt
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x002,00002000
Memory Limit: none
Rebooting in 1 seconds..
Fix this by adding a NULL check in mall_classify().
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*s) + s->nkeys*sizeof(struct tc_u32_key)
with:
struct_size(s, keys, s->nkeys)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although devlink health report does a nice job on reporting TX
timeout and other NIC errors, unfortunately it requires drivers
to support it but currently only mlx5 has implemented it.
Before other drivers could catch up, it is useful to have a
generic tracepoint to monitor this kind of TX timeout. We have
been suffering TX timeout with different drivers, we plan to
start to monitor it with rasdaemon which just needs a new tracepoint.
Sample output:
ksoftirqd/1-16 [001] ..s2 144.043173: net_dev_xmit_timeout: dev=ens3 driver=e1000 queue=0
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit cd9ff4de0107 changed the key for IFF_POINTOPOINT devices to
INADDR_ANY but neigh_xmit which is used for MPLS encapsulations was not
updated to use the altered key. The result is that every packet Tx does
a lookup on the gateway address which does not find an entry, a new one
is created only to find the existing one in the table right before the
insert since arp_constructor was updated to reset the primary key. This
is seen in the allocs and destroys counters:
ip -s -4 ntable show | head -10 | grep alloc
which increase for each packet showing the unnecessary overhread.
Fix by having neigh_xmit use __ipv4_neigh_lookup_noref for NEIGH_ARP_TABLE.
Fixes: cd9ff4de0107 ("ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY")
Reported-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ian and Alan both reported seeing overflows after upgrades to 5.x kernels:
neighbour: arp_cache: neighbor table overflow!
Alan's mpls script helped get to the bottom of this bug. When a new entry
is created the gc_entries counter is bumped in neigh_alloc to check if a
new one is allowed to be created. ___neigh_create then searches for an
existing entry before inserting the just allocated one. If an entry
already exists, the new one is dropped in favor of the existing one. In
this case the cleanup path needs to drop the gc_entries counter. There
is no memory leak, only a counter leak.
Fixes: 58956317c8d ("neighbor: Improve garbage collection")
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Reported-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use core provided API to fill the source MAC address and use
rdma_read_gid_attr_ndev_rcu() to get stable netdev.
This is preparation patch to allow gid attribute to become NULL when
associated net device is removed.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Three trivial overlapping conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
syzbot was able to crash host by sending UDP packets with a 0 payload.
TCP does not have this issue since we do not aggregate packets without
payload.
Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.
BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr ffff88808893fff0 by task syz-executor612/7889
CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
call_gro_receive include/linux/netdevice.h:2349 [inline]
udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:00007ffe8c716118 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007ffe8c716150 RCX: 0000000000441cc0
RDX: 0000000000000001 RSI: 00007ffe8c716170 RDI: 00000000000000f0
RBP: 0000000000000000 R08: 000000000000ffff R09: 0000000000a64668
R10: 0000000020000040 R11: 0000000000000246 R12: 000000000000c2d9
R13: 0000000000402b50 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 5143:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_kmalloc mm/kasan/common.c:497 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
slab_post_alloc_hook mm/slab.h:437 [inline]
slab_alloc mm/slab.c:3393 [inline]
kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
mm_alloc+0x1d/0xd0 kernel/fork.c:1030
bprm_mm_init fs/exec.c:363 [inline]
__do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 5351:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
__cache_free mm/slab.c:3499 [inline]
kmem_cache_free+0x86/0x260 mm/slab.c:3765
__mmdrop+0x238/0x320 kernel/fork.c:677
mmdrop include/linux/sched/mm.h:49 [inline]
finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
context_switch kernel/sched/core.c:2880 [inline]
__schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
retint_kernel+0x1b/0x2d
arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
kmem_cache_free+0xab/0x260 mm/slab.c:3766
anon_vma_chain_free mm/rmap.c:134 [inline]
unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
free_pgtables+0x1af/0x2f0 mm/memory.c:394
exit_mmap+0x2d1/0x530 mm/mmap.c:3144
__mmput kernel/fork.c:1046 [inline]
mmput+0x15f/0x4c0 kernel/fork.c:1067
exec_mmap fs/exec.c:1046 [inline]
flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
search_binary_handler fs/exec.c:1656 [inline]
search_binary_handler+0x17f/0x570 fs/exec.c:1634
exec_binprm fs/exec.c:1698 [inline]
__do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff88808893f7c0
which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
1496-byte region [ffff88808893f7c0, ffff88808893fd98)
The buggy address belongs to the page:
page:ffffea0002224f80 count:1 mapcount:0 mapping:ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw: 01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw: ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a followup after the fix in
commit 9c69a1320515 ("route: Avoid crash from dereferencing NULL rt->from")
rt6_do_redirect():
1. NULL checking is needed on rt->from because a parallel
fib6_info delete could happen that sets rt->from to NULL.
(e.g. rt6_remove_exception() and fib6_drop_pcpu_from()).
2. fib6_info_hold() is not enough. Same reason as (1).
Meaning, holding dst->__refcnt cannot ensure
rt->from is not NULL or rt->from->fib6_ref is not 0.
Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc()
is already doing, this patch chooses to extend the rcu section
to keep "from" dereference-able after checking for NULL.
inet6_rtm_getroute():
1. NULL checking is also needed on rt->from for a similar reason.
Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED.
Fixes: a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the endiannes is being handled correctly as indicated by the comment
above the offending line - sparse was unhappy with the missing annotation
as be64_to_cpu() expects a __be64 argument. To mitigate this annotation
all involved variables are changed to a consistent __le64 and the
conversion to uint64_t delayed to the call to rds_cong_map_updated().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.
As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.
Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
- the correct iif is observed if forwarding path does not involve
fragmentation/refragmentation
- a bogus iif is observed if forwarding path involves
fragmentation/refragmentatiom
Fix, by preserving skb_iif during 'ip_copy_metadata'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1Q-2018 defines the concept of a cycle-time-extension, so the
last entry of a schedule before the start of a new schedule can be
extended, so "too-short" entries can be avoided.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1Q-2018 defines that a the cycle-time of a schedule may be
overridden, so the schedule is truncated to a determined "width".
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.
Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.
The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):
$ tc qdisc change taprio dev IFACE parent root \
base-time X \
sched-entry <CMD> <GATES> <INTERVAL> \
...
Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.
Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.
So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.
For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.
Example:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time $BASE_TIME \
sched-entry S 00 500000 \
sched-entry S 0f 500000 \
clockid CLOCK_TAI
The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
