| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux
Santosh Shilimkar says:
====================
RDS: connection scalability and performance improvements
[v4]
Re-sending the same patches from v3 again since my repost of
patch 05/14 from v3 was whitespace damaged.
[v3]
Updated patch "[PATCH v2 05/14] RDS: defer the over_batch work to
send worker" as per David Miller's comment [4] to avoid the magic
value usage. Patch now makes use of already available but unused
send_batch_count module parameter. Rest of the patches are same as
earlier version v2 [3]
[v2]:
Dropped "[PATCH 05/15] RDS: increase size of hash-table to 8K" from
earlier version [1]. I plan to address the hash table scalability using
re-sizable hash tables as suggested by David Laight and David Miller [2]
This series addresses RDS connection bottlenecks on massive workloads and
improve the RDMA performance almost by 3X. RDS TCP also gets a small gain
of about 12%.
RDS is being used in massive systems with high scalability where several
hundred thousand end points and tens of thousands of local processes
are operating in tens of thousand sockets. Being RC(reliable connection),
socket bind and release happens very often and any inefficiencies in
bind hash look ups hurts the overall system performance. RDS bin hash-table
uses global spin-lock which is the biggest bottleneck. To make matter worst,
it uses rcu inside global lock for hash buckets.
This is being addressed by simply using per bucket rw lock which makes the
locking simple and very efficient. The hash table size is still an issue and
I plan to address it by using re-sizable hash tables as suggested on the list.
For RDS RDMA improvement, the completion handling is revamped so that we
can do batch completions. Both send and receive completion handlers are
split logically to achieve the same. RDS 8K messages being one of the
key usecase, mr pool is adapted to have the 8K mrs along with default 1M
mrs. And while doing this, few fixes and couple of bottlenecks seen with
rds_sendmsg() are addressed.
Series applies against 4.3-rc1 as well net-next. Its tested on Oracle
hardware with IB fabric for both bcopy as well as RDMA mode. RDS TCP is
tested with iXGB NIC. Like last time, iWARP transport is untested with
these changes. The patchset is also available at below git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux.git net/rds/4.3-v3
As a side note, the IB HCA driver I used for testing misses at least 3
important patches in upstream to see the full blown IB performance and
am hoping to get that in mainline with help of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compute net and store it in a variable in the functions
ip_build_and_send_pkt and ip_queue_xmit so that it does not need to be
recomputed next time it is needed.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store net in a variable in ip_tunnel_xmit so it does not need
to be recomputed when it is used again.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop hidding the sk parameter with an inline helper function and make
all of the callers pass it, so that it is clear what the function is
doing.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only __ip6_local_out_sk has callers so rename __ip6_local_out_sk
__ip6_local_out and remove the previous __ip6_local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is confusing and silly hiding a parameter so modify all of
the callers to pass in the appropriate socket or skb->sk if
no socket is known.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For consistency with the other similar methods in the kernel pass a
struct sock into the dst_ops .local_out method.
Simplifying the socket passing case is needed a prequel to passing a
struct net reference into .local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace dst_output_okfn with dst_output
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a packet has been encapsulated by a tunnel we should use the
tunnel sockets local multicast loopback flag to control if the
encapsulated packet should be locally loopback back.
Pass sk into ip_local_out_sk so that in the rare case we are dealing
with a tunneled packet whose tunnel destination address is a multicast
address the kernel properly decides to loopback this packet.
In practice I don't think this matters as ip_queue_xmit is used by
tcp, l2tp and sctp none of which I am aware of uses ip level
multicasting as they are all point to point communications protocols.
Let's fix this before someone uses ip_queue_xmit for a tunnel protocol
that does use multicast.
Fixes: aad88724c9d5 ("ipv4: add a sock pointer to dst->output() path.")
Fixes: b0270e91014d ("ipv4: add a sock pointer to ip_queue_xmit()")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the rare case where sk != skb->sk ip_local_out_sk arranges
to call dst->output differently if the skb is queued or not.
This is a bug.
Fix this bug by passing the sk parameter of ip_local_out_sk through
from ip_local_out_sk to __ip_local_out_sk (skipping __ip_local_out).
Fixes: 7026b1ddb6b8 ("netfilter: Pass socket pointer down through okfn().")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some applications use a listen() backlog of 1.
Prior kernels were silently enforcing a qlen_log of 4, so that we were
sending up to /proc/sys/net/ipv4/tcp_synack_retries SYNACK messages.
Fixes: ef547f2ac16b ("tcp: remove max_qlen_log")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed an assignment coding style issue
Signed-off-by: Yuvaraja Mariappan <ymariappan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_MULTICAST_ROUTER to allow setting/getting port's
multicast_router via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_FLUSH to allow flushing port's fdb similar to sysfs's
flush.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following attributes in order to export port's timer values:
IFLA_BRPORT_MESSAGE_AGE_TIMER, IFLA_BRPORT_FORWARD_DELAY_TIMER and
IFLA_BRPORT_HOLD_TIMER.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_TOPOLOGY_CHANGE_ACK and IFLA_BRPORT_CONFIG_PENDING to
allow getting port's topology_change_ack and config_pending respectively
via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_(ID|NO) to allow getting port's port_id and port_no
respectively via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_DESIGNATED_(COST|PORT) to allow getting the port's
designated cost and port respectively via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_BRIDGE_ID to allow getting the designated bridge id via
netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IFLA_BRPORT_ROOT_ID to allow getting the designated root id via
netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the user specifies a VRF device in a get route query the custom route
pointing to the VRF device is returned:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev vrf-red
cache
Add the flags to skip the custom route and go directly to the FIB. With
this patch the actual route is returned:
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev eth1 src 10.2.1.2
cache
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ping originated on box through a VRF device is showing up in tcpdump
without a source address:
$ tcpdump -n -i vrf-blue
08:58:33.311303 IP 0.0.0.0 > 10.2.2.254: ICMP echo request, id 2834, seq 1, length 64
08:58:33.311562 IP 10.2.2.254 > 10.2.2.2: ICMP echo reply, id 2834, seq 1, length 64
Add the call to l3mdev_get_saddr to raw_sendmsg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add operation to l3mdev to lookup source address for a given flow.
Add support for the operation to VRF driver and convert existing
IPv4 hooks to use the new lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 addrconf keys off of IFF_SLAVE so can not use it for L3 slave.
Add a new private flag and add netif_is_l3_slave function for checking
it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It occurred to me yesterday that 741a11d9e4103 ("net: ipv6: Add
RT6_LOOKUP_F_IFACE flag if oif is set") means that xfrm6_dst_lookup
needs the FLOWI_FLAG_SKIP_NH_OIF flag set. This latest commit causes
the oif to be considered in lookups which is known to break vti. This
explains why 58189ca7b274 did not the IPv6 change at the time it was
submitted.
Fixes: 42a7b32b73d6 ("xfrm: Add oif to dst lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink attributes for IPv6 tunnel addresses. This enables IPv6 support
for tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store tunnel protocol (AF_INET or AF_INET6) in sw_flow_key. This field now
also acts as an indicator whether the flow contains tunnel data (this was
previously indicated by tun_key.u.ipv4.dst being set but with IPv6 addresses
in an union with IPv4 ones this won't work anymore).
The new field was added to a hole in sw_flow_key.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When KASAN is enabled the frame size grows > 2048 bytes and we get a
warning, so make it smaller.
net/bridge/br_netlink.c: In function 'br_fill_info':
>> net/bridge/br_netlink.c:1110:1: warning: the frame size of 2160 bytes
>> is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for filtering neighbor dumps by device by adding the
NDA_IFINDEX attribute to the dump request.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add additional error reporting to the generic DSA code, so it's easier
to debug when things go wrong. This was useful when initially bringing
up 88e6176 on a new board.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes
net/built-in.o: In function `fib_rebalance':
fib_semantics.c:(.text+0x9df14): undefined reference to `__divdi3'
and
net/built-in.o: In function `fib_rebalance':
net/ipv4/fib_semantics.c:572: undefined reference to `__aeabi_ldivmod'
Fixes: 0e884c78ee19 ("ipv4: L3 hash-based multipath")
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8K message sizes are pretty important usecase for RDS current
workloads so we make provison to have 8K mrs available from the pool.
Based on number of SG's in the RDS message, we pick a pool to use.
Also to make sure that we don't under utlise mrs when say 8k messages
are dominating which could lead to 8k pull being exhausted, we fall-back
to 1m pool till 8k pool recovers for use.
This helps to at least push ~55 kB/s bidirectional data which
is a nice improvement.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
All HCA drivers seems to popullate max_mr caps and few of
them do both max_mr and max_fmr.
Hence update RDS code to make use of max_mr.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Fix below warning by marking rds_ib_fmr_wq static
net/rds/ib_rdma.c:87:25: warning: symbol 'rds_ib_fmr_wq' was not declared. Should it be static?
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
rds_ib_mr already keeps the pool handle which it associates
with. Lets use that instead of round about way of fetching
it from rds_ib_device.
No functional change.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
RDS IB mr pool has its own workqueue 'rds_ib_fmr_wq', so we need
to use queue_delayed_work() to kick the work. This was hurting
the performance since pool maintenance was less often triggered
from other path.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Just in case we are still handling the QP receive completion while the
rds_ibdev is released, drop the connection instead of crashing the kernel.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Similar to what we did with receive CQ completion handling, we split
the transmit completion handler so that it lets us implement batched
work completion handling.
We re-use the cq_poll routine and makes use of RDS_IB_SEND_OP to
identify the send vs receive completion event handler invocation.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
For better performance, we split the receive completion IRQ handler. That
lets us acknowledge several WCE events in one call. We also limit the WC
to max 32 to avoid latency. Acknowledging several completions in one call
instead of several calls each time will provide better performance since
less mutual exclusion locks are being performed.
In next patch, send completion is also split which re-uses the poll_cq()
and hence the code is moved to ib_cm.c
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
In Transport indepedent rds_sendmsg(), we shouldn't make decisions based
on RDS_LL_SEND_FULL which is used to manage the ring for RDMA based
transports. We can safely issue rds_send_xmit() and the using its
return value take decision on deferred work. This will also fix
the scenario where at times we are seeing connections stuck with
the LL_SEND_FULL bit getting set and never cleared.
We kick krdsd after any time we see -ENOMEM or -EAGAIN from the
ring allocation code.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Current process gives up if its send work over the batch limit.
The work queue will get kicked to finish off any other requests.
This fixes remainder condition from commit 443be0e5affe ("RDS: make
sure not to loop forever inside rds_send_xmit").
The restart condition is only for the case where we reached to
over_batch code for some other reason so just retrying again
before giving up.
While at it, make sure we use already available 'send_batch_count'
parameter instead of magic value. The batch count threshold value
of 1024 came via commit 443be0e5affe ("RDS: make sure not to loop
forever inside rds_send_xmit"). The idea is to process as big a
batch as we can but at the same time we don't hold other waiting
processes for send. Hence back-off after the send_batch_count
limit (1024) to avoid soft-lock ups.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The function returns always non-negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
