summaryrefslogtreecommitdiff
path: root/sound/firewire/Kconfig
AgeCommit message (Collapse)Author
2019-01-21ALSA: fireface: add support for Fireface UCXTakashi Sakamoto
Fireface UFX was shipped by RME GmbH in 2012. This model supports later protocol for management of isochronous communication and synchronization of sampling transmission frequency. This commit adds support for the model. At present, it's not clear how to encode MIDI messages and decide destination address for asynchronous transaction, thus this commit adds support for isochronous communication for PCM frames only. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-12-11ALSA: fireface: add support for Fireface 800 with MIDI functionality onlyTakashi Sakamoto
Fireface 800 is a flagship model of RME GmbH for audio and music units on IEEE 1394 bus, shipped 2004. This model consists of four chips: - TI TSB81BA3D for physical layer on cable environment of EEE 1394 bus - TI TSB82AA2 for link layer for 1394 OHCI bus bridge to PCI bus - Xilinx Spartan-3 FPGA XC3S400 - Xilinx High-Performance CPLD XC9572XL This commit adds support Fireface 800. In this time, the support is restricted to its MIDI functionality, thus this commit adds some condition statements to avoid touching streaming functionality. Unlike Fireface 400, Fireface 800 has no functionality to suppress asynchronous transactions for MIDI messages except for unregister of listen address in controller side, thus the feature is available as is. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-11-13ALSA: oxfw: add support for APOGEE duet FireWireTakashi Sakamoto
This commit adds support for APOGEE duet FireWire, launched 2007, already discontinued. This model uses Oxford Semiconductor FW971 as its communication engine. Below is information on Configuration ROM of this unit. The unit supports some AV/C commands defined by Audio subunit specification and vendor dependent commands. $ ./hinawa-config-rom-printer /dev/fw1 { 'bus-info': { 'adj': False, 'bmc': False, 'chip_ID': 42949742248, 'cmc': False, 'cyc_clk_acc': 255, 'generation': 0, 'imc': False, 'isc': True, 'link_spd': 3, 'max_ROM': 0, 'max_rec': 64, 'name': '1394', 'node_vendor_ID': 987, 'pmc': False}, 'root-directory': [ ['VENDOR', 987], ['DESCRIPTOR', 'Apogee Electronics'], ['MODEL', 122333], ['DESCRIPTOR', 'Duet'], [ 'NODE_CAPABILITIES', { 'addressing': {'64': True, 'fix': True, 'prv': False}, 'misc': {'int': False, 'ms': False, 'spt': True}, 'state': { 'atn': False, 'ded': False, 'drq': True, 'elo': False, 'init': False, 'lst': True, 'off': False}, 'testing': {'bas': False, 'ext': False}}], [ 'UNIT', [ ['SPECIFIER_ID', 41005], ['VERSION', 65537], ['MODEL', 122333], ['DESCRIPTOR', 'Duet']]]]} Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-10-12ALSA: firewire-motu: add missing entries to KconfigTakashi Sakamoto
MOTU Traveler and Audio Express are supported as well. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-04-05ALSA: fireface: add support for Fireface 400Takashi Sakamoto
Fireface 400 is a second model of RME Fireface series, released in 2006. This commit adds support for this model. This model supports 8 analog channels, 2 S/PDIF channels and 8 ADAT channels in both of tx/rx packet. The number of ADAT channels differs depending on each mode of sampling transmission frequency. $ python2 linux-firewire-utils/src/crpp < /sys/bus/firewire/devices/fw1/config_rom ROM header and bus information block ----------------------------------------------------------------- 400 04107768 bus_info_length 4, crc_length 16, crc 30568 (should be 61311) 404 31333934 bus_name "1394" 408 20009002 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 9 (1024) 40c 000a3501 company_id 000a35 | 410 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a root directory ----------------------------------------------------------------- 414 000485ec directory_length 4, crc 34284 418 03000a35 vendor 41c 0c0083c0 node capabilities per IEEE 1394 420 8d000006 --> eui-64 leaf at 438 424 d1000001 --> unit directory at 428 unit directory at 428 ----------------------------------------------------------------- 428 000314c4 directory_length 3, crc 5316 42c 12000a35 specifier id 430 13000002 version 434 17101800 model eui-64 leaf at 438 ----------------------------------------------------------------- 438 000261a8 leaf_length 2, crc 25000 43c 000a3501 company_id 000a35 | 440 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-04-05ALSA: fireface: add hwdep interfaceTakashi Sakamoto
This commit adds hwdep interface so as the other drivers for audio and music units on IEEE 1394 have. This interface is designed for mixer/control applications. By using this interface, an application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-04-05ALSA: fireface: add skeleton for RME Fireface seriesTakashi Sakamoto
This commit adds a new driver for RME Fireface series. This commit just creates/removes card instance according to IEEE 1394 bus event. More functions will be added in following commits. Three types of firmware have released by RME GmbH; for Fireface 400, for Fireface 800 and for UCX/802/UFX. It's reasonable that these models use different protocol for communication. Currently, I've investigated Fireface 400 and nothing others. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-03-28ALSA: firewire-motu: add support for MOTU 828mk3 (FireWire/Hybrid) as a ↵Takashi Sakamoto
model with protocol version 3 MOTU 828mk3 (FireWire/Hybrid) is one of third generation in MOTU FireWire series, produced in 2008/2014. This model consists of three chips for functionality on IEEE 1394 bus: * TI TSB41AB2 (Physical layer for IEEE 1394 bus) * Xilinx Spartan-3E FPGA Family (Link layer for IEEE 1394 bus, packet processing and data block processing layer) * TI TMS320C6722 (Digital signal processing) This commit adds a support for this model, with its unique protocol as version 3. This protocol has some additional features to protocol version 2. * Support several optical interfaces. * Support a data chunk for return of reverb effect. * Have a quirk of tx packets. * Support heartbeat asynchronous transaction. In this protocol, series of transferred packets has some quirks. Below fields in CIP headers of the packets are out of IEC 61883-1: - SID (source node id): always 0x0d - DBS (data block size): always 0x04 - DBC (data block counter): always 0x00 - EOH (End of header): always 0x00 Below is an actual sample of transferred packets. quads CIP1 CIP2 520 0x0D040400 0x22FFFFFF 8 0x0D040400 0x22FFFFFF 520 0x0D040400 0x22FFFFFF 520 0x0D040400 0x22FFFFFF 8 0x0D040400 0x22FFFFFF Status of clock is configured by write transactions to 0x'ffff'f000'0b14, as well as version 2, while meanings of fields are different from the former protocols. Modes of optical interfaces are configured by write transactions to 0x'ffff'f000'0c94. Drivers can register its address to receive heatbeat transactions from the unit. 0x'ffff'f000'0b0c is for the higher part and 0x'ffff'f000'0b10 is for the lower part. Nevertheless, this feature is not useless for this driver and this commit omits it. Each data block consists of two parts in a point of the number of included data chunks. In both of 'fixed' and 'differed' parts, the number of included data blocks are a multiple of 4, thus depending on models there's some empty data chunks. For example, 828mk3 includes one pair of empty data chunks in its fixed part. When optical interface is configured to S/PDIF, 828mk3 includes one pair of empty data chunks in its differed part. To reduce consumption of CPU cycles with additional conditions/loops, this commit just exposes these empty chunks to user space as PCM channels. Additionally, 828mk3 has a non-negligible overhead to change its sampling transfer frequency. When softwares send asynchronous transaction to perform it, LED on the unit starts to blink. In a worst case, it continues blink during several seconds; e.g. 10 seconds. When stopping blinking, the unit seems to be prepared for the requested sampling transfer frequency. To wait for the preparation, this commit forces the driver to call task scheduler and applications sleeps for 4 seconds. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-03-28ALSA: firewire-motu: add support for MOTU 828mk2 as a model with protocol ↵Takashi Sakamoto
version 2 MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in 2003. This model consists of four chips: * TI TSB41AB2 (Physical layer for IEEE 1394 bus) * PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer) * ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer) * TI TMS320VC5402 (Digital signal processing) This commit adds a support for this model, with its unique protocol as version 2. The features of this protocol are: * Support data chunks for status and control messages for both directions. * Support a pair of MIDI input/output. * Support a data chunk for mic/instrument independent of analog line in. * Support a data chunk for playback return. * Support independent data chunks for S/PDIF of both optical/coaxial interfaces. * Support independent data chunks for each of main out and phone out. Status of clock is configured by write transactions to 0x'ffff'f000'0b14. Modes of optical interfaces are configured by write transactions to 0x'ffff'f000'0c04. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-03-28ALSA: firewire-motu: add skeleton for Mark of the unicorn (MOTU) FireWire seriesTakashi Sakamoto
This commit adds an new driver for MOTU FireWire series. In this commit, this driver just creates/removes card instance according to bus event. More functionalities will be added in following commits. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-01-03ALSA: oxfw: add support for Mackie Onyx 1640iTakashi Sakamoto
As of kernel 4.10, ALSA OXFW driver has no entry for Onyx 1640i produced by Mackie (Loud Technologies). This commit supplement it. I note that there're two models produced by Mackie (Loud Technologies), which have the same name 'Onyx 1640i'. The former model based on OXFW970, the latter model based on Dice. This is probably due to low quality of communication of OXFW series. Additionally, the tester reports his or her experiences to get unexpected result at higher sampling transmission frequency as 88.2/96.0 kHz. We didn't have further investigation yet[0]. $ ./linux-firewire-utils/src/crpp < config_rom ROM header and bus information block ----------------------------------------------------------------- 400 042525ce bus_info_length 4, crc_length 37, crc 9678 404 31333934 bus_name "1394" 408 20ff5003 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 5 (64) 40c 000ff205 company_id 000ff2 | 410 00000fcf device_id 0500000fcf | EUI-64 000ff20500000fcf root directory ----------------------------------------------------------------- 414 0006c1b7 directory_length 6, crc 49591 418 03000ff2 vendor 41c 8100000a --> descriptor leaf at 444 420 17001640 model 424 81000011 --> descriptor leaf at 468 428 0c0083c0 node capabilities per IEEE 1394 42c d1000001 --> unit directory at 430 unit directory at 430 ----------------------------------------------------------------- 430 00040b97 directory_length 4, crc 2967 434 1200a02d specifier id: 1394 TA 438 13010001 version: AV/C 43c 17001640 model 440 81000010 --> descriptor leaf at 480 descriptor leaf at 444 ----------------------------------------------------------------- 444 0008a886 leaf_length 8, crc 43142 448 00000000 textual descriptor 44c 00000000 minimal ASCII 450 4c6f7564 "Loud" 454 20546563 " Tec" 458 686e6f6c "hnol" 45c 6f676965 "ogie" 460 7320496e "s In" 464 632e0000 "c." descriptor leaf at 468 ----------------------------------------------------------------- 468 00059fcf leaf_length 5, crc 40911 46c 00000000 textual descriptor 470 00000000 minimal ASCII 474 4f6e7978 "Onyx" 478 20313634 " 164" 47c 30690000 "0i" descriptor leaf at 480 ----------------------------------------------------------------- 480 00059fcf leaf_length 5, crc 40911 484 00000000 textual descriptor 488 00000000 minimal ASCII 48c 4f6e7978 "Onyx" 490 20313634 " 164" 494 30690000 "0i" [0]: [FFADO-user] Mackie 1640i issues (finer details) https://sourceforge.net/p/ffado/mailman/message/35229260/ Tested-by: Seth O'Bannion <saobannion@gmail.com> Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2016-03-28ALSA: firewire-tascam: add Kconfig entry for TASCAM FW-1804Takashi Sakamoto
I forgot it. Fixes: 3e78e1518e12('ALSA: firewire-tascam: add support for FW-1804') Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-12-22ALSA: oxfw: obsolete scs1x moduleTakashi Sakamoto
Now ALSA oxfw driver gains functionalities which scs1x module has. This commit obsoletes the scs1x module, and adds a line of MODULE_ALIAS to load oxfw module instead of scs1x module. In scs1x module, the name of 'shortname' field is fixed as 'SCS1x'. This field is used to name MIDI ports for both of SCS.1m and SCS.1d. This is not good because typically some SCS.1m and SCS.1d are used in the same system. It's better to distinguish them according to name of the ports. This commit applies model name in config ROM to the 'shortname'. For the name of 'driver' and 'longname', this commit uses the same way applied to the other models. This change may not bring disadvantages to users because userspace applications use ALSA rawmidi or seq interface and these interfaces are not influenced by them directly. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-11-08ALSA: oxfw: add an comment to Kconfig for TASCAM FireOneTakashi Sakamoto
A commit to add support for this model should have added a comment about this model to Kconfig. Fixes: 759a2f40c9fa('ALSA: oxfw: add an entry for TASCAM FireOne') Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-10-02ALSA: firewire-tascam: add hwdep interfaceTakashi Sakamoto
This commit adds hwdep interface so as the other IEEE 1394 sound devices has. This interface is designed for mixer/control applications. By using this interface, an application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-10-02ALSA: firewire-tascam: add skeleton for TASCAM FireWire seriesTakashi Sakamoto
This commit adds a new driver for TASCAM FireWire series. In this commit, this driver just creates/removes card instance according to bus event. More functionalities will be added in following commits. TASCAM FireWire series consists of: * PDI 1394P23 for IEEE 1394 PHY layer * PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface * XILINX XC9536XL * XILINX Spartan-II XC2S100 * ATMEL AT91M42800A Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and discover some features of his FW-1804. You can see a part of his research in FFADO project. http://subversion.ffado.org/wiki/Tascam A part of my work are based on Ilya's investigation, while this series doesn't support the FW-1804, because of a lack of config ROM information and its protocol detail, especially for PCM channels. I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI controller based on VT6315. The controller can actually communicate packets to these models, while these models generate no sounds. It may be due to the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other vendors such as Texas Instruments may work. Or adding another node on the bus. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-09-30ALSA: firewire-digi00x: add hwdep interfaceTakashi Sakamoto
This commit adds hwdep interface so as the other sound drivers for units on IEEE 1394 bus have. This interface is designed for mixer/control applications. By using this interface, an application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-09-30ALSA: firewire-digi00x: add skeleton for Digi 002/003 familyTakashi Sakamoto
This commit adds a new driver for Digidesign 002/003 family. This commit just creates/removes card instance according to bus event. More functions will be added in following commits. Digidesign 002/003 family consists of: * Agere FW802B for IEEE 1394 PHY layer * PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface * ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller * ADSP-21065L for signal processing [minor cleanup using skip_spaces() by tiwai] Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-06-15ALSA: bebob: add support for Behringer FCA 610/1616Takashi Sakamoto
They're based on DM1500 (ArchWave produced), and BeBoB version 3 is installed. $ cat /proc/asound/FCA610/firewire/firmware Manufacturer: bridgeCo Protocol Ver: 3 Build Ver: 0 GUID: 0x001564000002AD73 Model ID: 0x03 Model Rev: 0 Firmware Date: 20121102 Firmware Time: 153431 Firmware ID: 0x610 Firmware Ver: 8348 Base Addr: 0x400C0080 Max Size: 1422624 Loader Date: 20121015 Loader Time: 104710 Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2015-05-24ALSA: bebob: add Digidesign Mbox 2 Pro supportTakashi Sakamoto
This device is based on DM1000E, and BeBoB version 1 firmware is installed. $ cat /proc/asound/cards 0 [Pro ]: BeBoB - Mbox 2 Pro DIGIDESIGN Mbox 2 Pro (id:1, rev:1), GUID 00a07e0100a90000 at fw1.0, S400 $ cat /proc/asound/Pro/firewire/firmware Manufacturer: bridgeCo Protocol Ver: 1 Build Ver: 0 GUID: 0x00A07E0100A90000 Model ID: 0x01 Model Rev: 1 Firmware Date: 20071031 Firmware Time: 034402 Firmware ID: 0xA9 Firmware Ver: 16777215 Base Addr: 0x20080000 Max Size: 1572864 Loader Date: 20051207 Loader Time: 205554 With this patch, ALSA BeBoB driver can start packet streaming to/from this model, while as a default, internal multiplexer of this model is not initialized and generates no sound even if the driver transfers any packets with PCM samples. To hear any sounds from this model, userspace applications should be developed to set parameters to the internal multiplexer. You can see raw information in FFADO website: http://subversion.ffado.org/wiki/AvcModels/DigiDesignMboxPro2 Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-12-10ALSA: oxfw: Add hwdep interfaceTakashi Sakamoto
This interface is designed for mixer/control application. By using this interface, an application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Acked-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-12-10ALSA: oxfw: Add support for Behringer/Mackie devicesTakashi Sakamoto
Some devices produced by Behringer/Mackie are based on OXFW970/971. This commit adds support for them. Additionally, this commit changes the way to name card with some information in config rom. Ids of some Mackie(Loud) models are not identified, therefore this commit applies name detection for these models. The devices support capture/playback of PCM-samples and some of them supports capture/playback of MIDI messages. These functionalities are implemented by followed commits. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Acked-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-12-10ALSA: dice: Add support for capturing PCM samplesTakashi Sakamoto
This commit adds a support for capturing PCM samples. When opposite PCM substream is already running, available sampling rate is limited at current one. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Acked-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-11-29ALSA: speakers: Rename to oxfw and rename some membersTakashi Sakamoto
This commit renames 'firewire-speakers' to 'oxfw' to enhance support for devices which based on OXFW970/971. A line for MODULE_ALIAS is added. Additionally, to help for works in followed paches, some members in private structure are renamed. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-11-29ALSA: dice: remove experimental stateTakashi Sakamoto
Some developers test this driver, thus it's better to remove its experimental state. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-07-28ALSA: firewire: trivial typo fixes in KconfigStefan Richter
ESI Quotafire -> QuataFire TerraTec EWS Mic4 -> Mic8 Firewire -> FireWire Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-30ALSA: firewire: Fix dependency on PCM and rawmidiTakashi Iwai
Now snd-firewire-lib supports rawmidi in addition to PCM, thus we need to give a proper dependency. For fixing and simplification, move the selections of SND_PCM and SND_RAWMIDI into SND_FIREWIRE_LIB section. Then each driver doesn't have to select them but only SND_FIREWIRE_LIB. Reported-by: Jim Davis <jim.epost@gmail.com> Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add support for M-Audio special Firewire seriesTakashi Sakamoto
This commit allows this driver to support some models which M-Audio produces with DM1000 but its firmware is special. They are: - Firewire 1814 - ProjectMix I/O They have heavily customized firmware. The usual operations can't be applied to them. For this reason, this commit adds a model specific member to 'struct snd_bebob' and some model specific functions. Some parameters are write-only so this commit also adds control interface for applications to set them. M-Audio special firmware quirks: - Just after powering on, they wait to download firmware. This state is changed when receiving cue. Then bus reset is generated and the device is recognized as a different model with the uploaded firmware. - They don't respond against BridgeCo AV/C extension commands. So drivers can't get their stream formations and so on. - They do not start to transmit packets only by establishing connection but also by receiving SIGNAL FORMAT command. - After booting up, they often fail to send response against driver's request due to mismatch of gap_count. This module don't support to upload firmware. Tested-by: Darren Anderson <darrena092@gmail.com> (ProjectMix I/O) Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add support for M-Audio usual Firewire seriesTakashi Sakamoto
This commit allows this driver to support some models which M-Audio produces with DM1000/DM1000E with usual firmware. They are: - Firewire 410 - Firewire AudioPhile - Firewire Solo - Ozonic - NRV10 - FirewireLightBridge According to a person who worked in BridgeCo, some models are produced with 'Pre-BeBoB'. This means that these products were released before BeBoB was officially produced, and later BeBoB specification was formed. So these models have some quirks. M-Audio usual firmware quirks: - Just after powering on, 'Firewire 410' waits to download firmware. This state is changed when receiving cue. Then bus reset is generated and the device is recognized as a different model with the uploaded firmware. - 'Firewire Audiophile' also waits to download firmware but its vendor id/model id is the same as the one after loading firmware. - The information of channel mapping for MIDI conformant data channel is invalid against BridgeCo specification. This commit adds some codes for these quirks but don't support to upload firmware. This commit also adds specific operations to get metering information. The metering information also includes status of clock synchronization if the model supports to switch source of clock. The specification of FirewireLightBridge is unknown. So in this time, normal operations are applied for this model. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add support for Focusrite Saffire/SaffirePro seriesTakashi Sakamoto
This commit allows this driver to support all of models which Focusrite produces with DM1000/BeBoB. They are: - Saffire - Saffire LE - SaffirePro 10 I/O - SaffirePro 26 I/O This commit adds Focusrite specific operations: 1. Get source of clock 2. Get/Set sampling frequency 3. Get metering information The driver uses these functionalities to read/write specific address by async transaction. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add support for Yamaha GO seriesTakashi Sakamoto
This commit allows this driver to support all of models which Yamaha produced with DM1000/BeBoB. They are: - GO44 - GO46 This commit adds Yamaha specific operations. To get source of clock, AV/C Audio Subunit command is used. I note that their appearances are similar to some models of TerraTec; 'Go44' is similar to 'PHASE 24 FW' and 'GO46' is similar to 'PHASE X24 FW'. But their combination of Audio/Music subunits is a bit different. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add support for Terratec PHASE, EWS series and AureonTakashi Sakamoto
This commit allows this driver to support all of models which Terratec produced with DM1000/BeBoB. They are: - PHASE 24 FW - PHASE X24 FW - PHASE 88 Rack FW - EWS MIC2 - EWS MIC4 - Aureon 7.1 Firewire For Phase series, this commit adds a Terratec specific operation. To get source of clock. AV/C Audio Subunit command is used. For EWS series and Aureon, this module uses normal operations. Tested-by: Maximilian Engelhardt <maxi@daemonizer.de> (PHASE 24 FW) Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add hwdep interfaceTakashi Sakamoto
This interface is designed for mixer/control application. By using hwdep interface, the application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add PCM interfaceTakashi Sakamoto
This commit adds a functionality to capture/playback PCM samples. When AMDTP stream is already running for PCM or the source of clock is not internal, available sampling rate is limited at current one. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add MIDI interfaceTakashi Sakamoto
This commit adds a functionality to capture/playback MIDI messages. When no AMDTP streams are running, this module starts AMDTP stream at current sampling rate for MIDI substream. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: bebob: Add skelton for BeBoB based devicesTakashi Sakamoto
This commit adds a new driver for BeBoB based devices with no specific operations. Currently this driver just create/remove card instance according to callbacks. BeBoB is 'BridgeCo enhanced Breakout Box'. This is installed to firewire devices with DM1000/DM1100/DM1500 chipset. It gives common way for host system to handle BeBoB based devices. Current supported devices: - Edirol FA-66/FA-101 - PreSonus FIREBOX/FIREPOD/FP10/Inspire1394 - BridgeCo RDAudio1/Audio5 - Mackie Onyx 1220/1620/1640 (Firewire I/O Card) - Mackie d.2 (Firewire Option) - Stanton FinalScratch 2 (ScratchAmp) - Tascam IF-FW DM - Behringer XENIX UFX 1204/1604 - Behringer Digital Mixer X32 series (X-UF Card) - Apogee Rosetta 200/Rosetta 400 (X-FireWire card) - Apogee DA-16X/AD-16X/DD-16X (X-FireWire card) - Apogee Ensemble - ESI Quotafire610 - AcousticReality eARMasterOne - CME MatrixKFW - Phonix Helix Board 12 MkII/18 MkII/24 MkII - Phonic Helix Board 12 Universal/18 Universal/24 Universal - Lynx Aurora 8/16 (LT-FW) - ICON FireXon - PrismSound Orpheus/ADA-8XR Devices possible to be supported if identifying IDs: - Apogee Mini-Me Firewire/Mini-DAC Firewire - Behringer F-Control Audio 610/1616 - Cakewalk Sonar Power Studio 66 - CME UF400e - ESI Quotafire XL - Infrasonic DewX/Windy6 - Mackie Digital X Bus x.200/400 - Phonic Helix Board 12/18/24 - Phonic FireFly 202/302 - Rolf Spuler Firewire Guitar Tested-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: fireworks: Add hwdep interfaceTakashi Sakamoto
This interface is designed for mixer/control application. To use hwdep interface, the application can get information about firewire node, can lock/unlock kernel streaming and can get notification at starting/stopping kernel streaming. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: fireworks: Add PCM interfaceTakashi Sakamoto
This commit adds a functionality to capture/playback PCM samples. When AMDTP stream is already running for PCM or the source of clock is not internal, available sampling rate is limited at current one. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: fireworks: Add MIDI interfaceTakashi Sakamoto
This commit adds a functionality to capture/playback MIDI messages. When no AMDTP streams are running, this driver starts AMDTP stream for MIDI stream at current sampling rate. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: fireworks: Add transaction and some commandsTakashi Sakamoto
Fireworks uses own command and response. This commit adds functionality to transact and adds some commands required for sound card instance and kernel streaming. There are two ways to deliver substance of this transaction: 1.AV/C vendor dependent command for command/response 2.Async transaction to specific addresses for command/response By way 1, I confirm AudioFire12 cannot correctly response to some commands with firmware version 5.0 or later. This is also confirmed by FFADO. So this driver implement way 2. The address for response gives an issue. When this driver allocate own callback function into the address, then no one can allocate its own callback function. This situation is not good for applications in user-land. This issue is solved in later commit. I note there is a command to change the address for response if the device supports. But this driver uses default value. So users should not execute this command as long as hoping this driver works correctly. Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2014-05-26ALSA: fireworks: Add skelton for Fireworks based devicesTakashi Sakamoto
This commit adds a new driver for devices based on Fireworks. This driver just creates/removes card instance according to callbacks. Fireworks is a board module which Echo Audio produced. This module consists of three chipsets: - Communication chipset for IEEE1394 PHY/Link and IEC 61883-1/6 - DSP or/and FPGA for signal processing - Flash Memory to store firmwares Current supported devices: - Mackie Onyx 400F/1200F - Echo AudioFire12/8(until 2009 July) - Echo AudioFire2/4/Pre8/8(since 2009 July) - Echo Fireworks 8/HDMI - Gibson Robot Interface pack/GoldTop Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-10-20ALSA: dice: restrict the driver to playback-only devicesClemens Ladisch
At the moment, this driver supports only playback, while FFADO supports (only) full-duplex devices. So, prevent conflicts by not claiming devices that would be better handled by FFADO. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2013-10-17ALSA: add DICE driverClemens Ladisch
As a start point for further development, this is an incomplete driver for DICE devices: - only playback (so no clock source except the bus clock) - only 44.1 kHz - no MIDI - recovery after bus reset is slow - hwdep device is created, but not actually implemented Contains compilation fixes by Stefan Richter. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2012-11-12ALSA: firewire: add Stanton SCS.1d/1m driverClemens Ladisch
Add a MIDI driver for the Stanton FireWire DJ controllers. Tested-by: Sean M. Pappalardo - D.J. Pegasus <spappalardo@mixxx.org> Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2011-05-11ALSA: isight: remove experimental statusClemens Ladisch
Experiments have shown this driver to work now. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-05-11ALSA: add Apple iSight microphone driverClemens Ladisch
This adds an experimental driver for the front and rear microphones of the Apple iSight web camera. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-03-15ALSA: add LaCie FireWire Speakers/Griffin FireWave Surround driverClemens Ladisch
Add a driver for two playback-only FireWire devices based on the OXFW970 chip. v2: better AMDTP API abstraction; fix fw_unit leak; small fixes v3: cache the iPCR value v4: FireWave constraints; fix fw_device reference counting; fix PCR caching; small changes and fixes v5: volume/mute support; fix crashing due to pcm stop races v6: fix build; one-channel volume for LaCie v7: use signed values to make volume (range checks) work; fix function block IDs for volume/mute; always use channel 0 for LaCie volume Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Jay Fenlason <fenlason@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>