| Age | Commit message (Collapse) | Author |
|---|
|
after bus-reset
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to restart packet streaming should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA fireface driver just stops packet
streaming in the update handler, thus pcm.prepare handler should
request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
pcm.hw_params/hw_free callbacks
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming for allocated the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for the protocol
specific to latter models. The encoded values of constant table is
split into several condition statements to separate the operation
to configure sampling transfer frequency from the operation to
configure the number of data channels in rx packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff400 protocol.
In this callback, sampling transfer frequency is configured to the
device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff800 protocol.
As I noted in commit fc716397a5c7 ("ALSA: fireface: add support for
packet streaming on Fireface 800"), this unit allocates isochronous
resources for tx stream voluntarily. Therefore, this commit is to
maintain isochronous rsources for rx stream. In the callback,
sampling transfer frequency is configured to the device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
resources
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
In ALSA fireface driver, the allocation of isochronous resources is
programmed in each implementation of protocol. This commit adds
protocol-specific operation for the allocation separated from
the operation to begin session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The pairs of pcm.hw_params callbacks and .hw_free callbacks for both
direction have no differences.
This commit unifies the pairs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The operation to finish packet streaming corresponds to stopping
isochronous contexts.
This commit applies code refactoring to move codes to stop into
a helper function to finish the session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
streaming after bus reset
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to restart packet streaming should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA firewire-tascam driver just stops
packet streaming in the update handler, thus pcm.prepare handler
should request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
pcm.hw_params/hw_free callbacks
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming for allocated the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit obsoletes a helper function to release isochronous resources
for both direction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit applies minor code refactoring for a helper function to
allocate isochronous resources.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
The registration of isochronous channels is done just after allocation
of isochronous resources. This commit separates the registration just
before starting packet streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The data for isochronous resources is not destroyed in expected place.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 9b2bb4f2f4a2 ("ALSA: firewire-motu: add stream management functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset. One
significant one-liner fix is the disablement of the node-power saving
on Realtek codecs, which may potentially cover annoying bugs like the
background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller"
* tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireface: Use ULL suffixes for 64-bit constants
ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops
ALSA: line6: Assure canceling delayed work at disconnection
ALSA: hda - Force polling mode on CNL for fixing codec communication
ALSA: hda/realtek - Enable micmute LED for Huawei laptops
ALSA: hda/realtek - Set default power save node to 0
ALSA: hda/realtek - Check headset type by unplug and resume
|
|
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64c2ca6c ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As a result of heavy refactoring based on IR context header, the packet
handler becomes simpler.
This commit merges the packet handler into function for IR context
callback. The logic to parse IR context header and tracepoints event is
split to a function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As a result of heavy refactoring based on IT packet header, the packet
handler becomes simpler.
This commit merges the packet handler into function for IT context
callback. The logic to build IT packet header and tracepoints event is
split to a function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The amdtp_packet events have inverted node IDs for src/dst. This commit
fixes the bug.
Fixes: 8d3f1fdf5211 ("ALSA: firewire-lib: unify tracing events to 'amdtp_packet' event")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
header
The value of data block counter is not calculated for incoming packet
without CIP header. This commit fixes the bug.
Fixes: 947b437e1263 ("ALSA: firewire-lib: unify packet handler for IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
header from CIP payload
In Linux firewire subsystem, for IT context, some quadlets of isochronous
packet payload can be indicated as a part of packet header to queue to
the context.
This commit uses the packet header to split CIP headers from CIP
payload. As a result, regardless of CIP or non-CIP, context payload
includes data blocks only.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is a preparation to queue IT packet with header. To enable
packet handler to fill the header, this commit uses kernel stack for
data structure of packet parameter in several part of this file.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The handlers for packet with CIP and without CIP include common codes.
This commit unifies them and remove an member for pointer to callback
function from data structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is minor code refactoring to split a function to generate CIP
header.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Usage of 16 bytes IR context header allows to handle context payload by
the same code for with-CIP and without-CIP packets.
This commit unifies both handlers of with-CIP and without-CIP packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IR context, some quadlets of packet payload can be included into
context header. This is good for packet with CIP header because the
context payload buffer can includes data blocks only for with-CIP and
without-CIP pakets.
This commit uses 16 bytes IR context header for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A parser for CIP header in incoming packet is enough large.
This commit splits it into a helper function to better looks of packet
handler.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The value of pointer to payload buffer is computed in each packet
handler, however the pointer can be decided before call of packet
handler.
This commit adds an argument for the pointer to the packet handler to
reduce codes to compute for the pointer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In current packet handler, the length of payload is given as an argument
of callback function, however this value is just required to process
payload of transferred isoc packet, thus just for IR context.
This commit replaces the argument for payload of packet with the
argument of context header. As a result, the length of payload is
computed in packet handler for IR context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit is to distinguish variable of CIP header from variable of
isochronous context header.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
scheduling packet
In IT context, header includes information of cycle to have processed
queued packet.
This commit uses the per-packet information to compute the cycle for
packet to be queued, instead of callback argument. In current
implementaion of ALSA IEC 61883-1/6 packet streaming engine, 48 packets
are queued at first to skip recent cycle. When IT context calls handler,
cycle information in header plus 48 cycle means the cycle to be going
to queue packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The header size parameter of 1394 OHCI IT context has no effect.
Besides the header size of queued packet is different from context
header.
This commit cleans codes relevant to these two headers.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In callback handler of isochronous context for both direction, there're
common codes to cancel context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some parameters of struct amdtp_stream is dependent on direction.
This commit uses union for such parameters to distinguish from
common parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now four events of this module have the same arguments and probe timing.
This commit adds a new event, 'amdtp_packet', and replace them. Filtering
functionality of tracing framework is available to pick up events for
inbound/outbound isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This modules handles two types of isochronous packet; one has CIP header
in IEC 61883-1/6 and another doesn't. The module also have tracing events
corresponding to the types of packet. To unify the events, one event
should be probed with or without CIP header.
This commit uses dynamic array for the events to be available for the
types of packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The most of tracing event in this module have the size of payload in
byte unit, however 'in_packet_without_header' event have the argument
in quadlet unit.
This commit change the unit for argument to be consistent.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
in_packet/out_packet tracing events
Tracing events for packets without CIP header have a parameter of
data_blocks/data_block_counter, but events for packets with CIP header
don't. This is not good to unify these events.
This commit adds the missing parameters to the events. In timing to
probe 'in_packet' event, data_blocks and data_block_counter are not
calculated yet. This commit also changes the timing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
event
An argument for CIP header in 'in_packet' event is not the same type in
'out_packet' event. This is not good to unify these events.
This commit uses the same type of argument for these events.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
FireStudio was launched by PreSonus 2009. This model consists of three
ICs for its packet processing on IEEE 1394 bus:
- Texus Instruments TSB41AB2 for physical layer of IEEE 1394 bus
- WaveFront semiconductor, Dice II STD ASIC for link layer of IEEE 1394
bus and protocol layer
- Xilinx Spartan XG3S500E FPGA for signal processing
This model don't support TCAT extended application protocol. For such
devices, ALSA dice driver needs to have hard-coded parameters for stream
formats.
This commit adds hard-coded table for this model. As a result, sampling
transfer frequencies of 88.2/96.0 kHz are supported. I note that this
patch can be backported to Linux kernel v4.18 and later.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04042eda bus_info_length 4, crc_length 4, crc 11994
404 31333934 bus_name "1394"
408 e0ff8112 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c 000a9204 company_id 000a92 |
410 023a8b7f device_id 04023a8b7f | EUI-64 000a9204023a8b7f
root directory
-----------------------------------------------------------------
414 000661b6 directory_length 6, crc 25014
418 03000a92 vendor
41c 8100000a --> descriptor leaf at 444
420 17000008 model
424 8100000d --> descriptor leaf at 458
428 0c0087c0 node capabilities per IEEE 1394
42c d1000001 --> unit directory at 430
unit directory at 430
-----------------------------------------------------------------
430 00041c75 directory_length 4, crc 7285
434 12000a92 specifier id
438 13000001 version
43c 17000008 model
440 8100000c --> descriptor leaf at 470
descriptor leaf at 444
-----------------------------------------------------------------
444 00047c11 leaf_length 4, crc 31761
448 00000000 textual descriptor
44c 00000000 minimal ASCII
450 50726553 "PreS"
454 6f6e7573 "onus"
descriptor leaf at 458
-----------------------------------------------------------------
458 0005d7b3 leaf_length 5, crc 55219
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 46495245 "FIRE"
468 53545544 "STUD"
46c 494f0000 "IO"
descriptor leaf at 470
-----------------------------------------------------------------
470 0005d7b3 leaf_length 5, crc 55219
474 00000000 textual descriptor
478 00000000 minimal ASCII
47c 46495245 "FIRE"
480 53545544 "STUD"
484 494f0000 "IO"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In kernel API of Linux FireWire subsystem, handlers of isochronous
receive (IR) context can get context headers as an argument of
callback. When 4 byte header is used, the context header includes
isochronous packet header for each packet. When 8 byte header is
used, it includes isochronous cycle as well.
ALSA IEC 61883-1/6 engine uses 4 byte header, and computes isochronous
cycle from the cycle of interrupt. The usage of 8 byte header can
obsolete the computation.
Furthermore, this change works well for a case that a series of
packet in one interrupt includes skipped isochronous cycle,
This commit uses 8 byte header to handle isochronous cycle.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds support for MOTU 8pre FireWire, which was shipped 2007
and nowadays already discontinued. Userspace applications can transmit
and receive PCM frames and MIDI messages for this model via ALSA PCM
interface and RawMidi/Sequencer interfaces.
Like the other models of MOTU FireWire series, this model has many
quirks in its CIP.
At first, data channels for two pairs of optical interfaces. At lower
sampling transmission frequency, i.e. 44.1 and 48.0 kHz, one pair is
available for ADAT data, thus 8 data chunks are transferred by CIP.
At middle sampling transmission frequency, i.e. 88.2 and 96.0 kHz,
two pairs are available to keep 8 chunks for ADAT data, thus CIP
still includes 8 data chunks.
Apart from data chunks for optical interface, CIP includes fixed number
of data chunks. In tx stream, two chunks for status message, eight
chunks for samples from analog 1-8 input, two chunks for mix-return.
In rx stream, two chunks for control message, two chunks for main 1-2
output, two chunks for phone 1-2 output, two chunks for dummy 1-2.
CIP header in tx stream includes quirks for its dbs and dbc fields.
The value of dbs field is fixed to 0x13, against its actual size.
The value of dbc field is firstly updated to 0x07 from zero, then
it's incremented continuously according to actual number of data h
blocks.
Finally, the model has own bits to disable frame fetch.
This commit uses several options to absorb the above quirks.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0410b57d bus_info_length 4, crc_length 16, crc 46461
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 00083dfb device_id 0000083dfb | EUI-64 0001f20000083dfb
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 0003991c directory_length 3, crc 39196
42c 120001f2 specifier id
430 1300000f version
434 17103800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 00022681 leaf_length 2, crc 9857
43c 0001f200 company_id 0001f2 |
440 00083dfb device_id 0000083dfb | EUI-64 0001f20000083dfb
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Current ALSA firewire-motu driver uses the value of 'model' field
of unit directory in configuration ROM for modalias for MOTU
FireWire models. However, as long as I checked, Pre8 and
828mk3(Hybrid) have the same value for the field (=0x100800).
unit | version | model
--------------- | --------- | ----------
828mkII | 0x000003 | 0x101800
Traveler | 0x000009 | 0x107800
Pre8 | 0x00000f | 0x100800 <-
828mk3(FW) | 0x000015 | 0x106800
AudioExpress | 0x000033 | 0x104800
828mk3(Hybrid) | 0x000035 | 0x100800 <-
When updating firmware for MOTU 8pre FireWire from v1.0.0 to v1.0.3,
I got change of the value from 0x100800 to 0x103800. On the other
hand, the value of 'version' field is fixed to 0x00000f. As a quick
glance, the higher 12 bits of the value of 'version' field represent
firmware version, while the lower 12 bits is unknown.
By induction, the value of 'version' field represents actual model.
This commit changes modalias to match the value of 'version' field,
instead of 'model' field. For degug, long name of added sound card
includes hexadecimal value of 'model' field.
Fixes: 6c5e1ac0e144 ("ALSA: firewire-motu: add support for Motu Traveler")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
This commit fixes the bug.
Reported-by: Peter Sjöberg <autopeter@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 4641c9394010 ("ALSA: firewire-motu: add MOTU specific protocol layer")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Liquid Saffire 56
ALSA bebob driver has an entry for Focusrite Saffire Pro 10 I/O. The
entry matches vendor_id in root directory and model_id in unit
directory of configuration ROM for IEEE 1394 bus.
On the other hand, configuration ROM of Focusrite Liquid Saffire 56
has the same vendor_id and model_id. This device is an application of
TCAT Dice (TCD2220 a.k.a Dice Jr.) however ALSA bebob driver can be
bound to it randomly instead of ALSA dice driver. At present, drivers
in ALSA firewire stack can not handle this situation appropriately.
This commit uses more identical mod_alias for Focusrite Saffire Pro 10
I/O in ALSA bebob driver.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 042a829d bus_info_length 4, crc_length 42, crc 33437
404 31333934 bus_name "1394"
408 f0649222 irmc 1, cmc 1, isc 1, bmc 1, pmc 0, cyc_clk_acc 100,
max_rec 9 (1024), max_rom 2, gen 2, spd 2 (S400)
40c 00130e01 company_id 00130e |
410 000606e0 device_id 01000606e0 | EUI-64 00130e01000606e0
root directory
-----------------------------------------------------------------
414 0009d31c directory_length 9, crc 54044
418 04000014 hardware version
41c 0c0083c0 node capabilities per IEEE 1394
420 0300130e vendor
424 81000012 --> descriptor leaf at 46c
428 17000006 model
42c 81000016 --> descriptor leaf at 484
430 130120c2 version
434 d1000002 --> unit directory at 43c
438 d4000006 --> dependent info directory at 450
unit directory at 43c
-----------------------------------------------------------------
43c 0004707c directory_length 4, crc 28796
440 1200a02d specifier id: 1394 TA
444 13010001 version: AV/C
448 17000006 model
44c 81000013 --> descriptor leaf at 498
dependent info directory at 450
-----------------------------------------------------------------
450 000637c7 directory_length 6, crc 14279
454 120007f5 specifier id
458 13000001 version
45c 3affffc7 (immediate value)
460 3b100000 (immediate value)
464 3cffffc7 (immediate value)
468 3d600000 (immediate value)
descriptor leaf at 46c
-----------------------------------------------------------------
46c 00056f3b leaf_length 5, crc 28475
470 00000000 textual descriptor
474 00000000 minimal ASCII
478 466f6375 "Focu"
47c 73726974 "srit"
480 65000000 "e"
descriptor leaf at 484
-----------------------------------------------------------------
484 0004a165 leaf_length 4, crc 41317
488 00000000 textual descriptor
48c 00000000 minimal ASCII
490 50726f31 "Pro1"
494 30494f00 "0IO"
descriptor leaf at 498
-----------------------------------------------------------------
498 0004a165 leaf_length 4, crc 41317
49c 00000000 textual descriptor
4a0 00000000 minimal ASCII
4a4 50726f31 "Pro1"
4a8 30494f00 "0IO"
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 040442e4 bus_info_length 4, crc_length 4, crc 17124
404 31333934 bus_name "1394"
408 e0ff8112 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c 00130e04 company_id 00130e |
410 018001e9 device_id 04018001e9 | EUI-64 00130e04018001e9
root directory
-----------------------------------------------------------------
414 00065612 directory_length 6, crc 22034
418 0300130e vendor
41c 8100000a --> descriptor leaf at 444
420 17000006 model
424 8100000e --> descriptor leaf at 45c
428 0c0087c0 node capabilities per IEEE 1394
42c d1000001 --> unit directory at 430
unit directory at 430
-----------------------------------------------------------------
430 000418a0 directory_length 4, crc 6304
434 1200130e specifier id
438 13000001 version
43c 17000006 model
440 8100000f --> descriptor leaf at 47c
descriptor leaf at 444
-----------------------------------------------------------------
444 00056f3b leaf_length 5, crc 28475
448 00000000 textual descriptor
44c 00000000 minimal ASCII
450 466f6375 "Focu"
454 73726974 "srit"
458 65000000 "e"
descriptor leaf at 45c
-----------------------------------------------------------------
45c 000762c6 leaf_length 7, crc 25286
460 00000000 textual descriptor
464 00000000 minimal ASCII
468 4c495155 "LIQU"
46c 49445f53 "ID_S"
470 41464649 "AFFI"
474 52455f35 "RE_5"
478 36000000 "6"
descriptor leaf at 47c
-----------------------------------------------------------------
47c 000762c6 leaf_length 7, crc 25286
480 00000000 textual descriptor
484 00000000 minimal ASCII
488 4c495155 "LIQU"
48c 49445f53 "ID_S"
490 41464649 "AFFI"
494 52455f35 "RE_5"
498 36000000 "6"
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: 25784ec2d034 ("ALSA: bebob: Add support for Focusrite Saffire/SaffirePro series")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The calls of snd_info_register() are superfluous and should be avoided
at the procfs creation time. They are called at the end of the whole
initialization via snd_card_register(). This patch drops such
superfluous calls.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Duende Classic was produced by Solid State Logic in 2006, as a
first model of Duende DSP series. The following model, Duende Mini
was produced in 2008. They are designed to receive isochronous
packets for PCM frames via IEEE 1394 bus, perform signal processing by
downloaded program, then transfer isochronous packets for converted
PCM frames.
These two models includes the same embedded board, consists of several
ICs below:
- Texus Instruments Inc, TSB41AB3 for physical layer of IEEE 1394 bus
- WaveFront semiconductor, DICE II STD ASIC for link/protocol layer
- Altera MAX 3000A CPLD for programs
- Analog devices, SHARC ADSP-21363 for signal processing (4 chips)
This commit adds support for the two models to ALSA dice driver. Like
support for the other devices, packet streaming is just available.
Userspace applications should be developed if full features became
available; e.g. program uploader and parameter controller.
$ ./hinawa-config-rom-printer /dev/fw1
{ 'bus-info': { 'adj': False,
'bmc': False,
'chip_ID': 349771402425,
'cmc': True,
'cyc_clk_acc': 255,
'generation': 1,
'imc': True,
'isc': True,
'link_spd': 2,
'max_ROM': 1,
'max_rec': 512,
'name': '1394',
'node_vendor_ID': 20674,
'pmc': False},
'root-directory': [ ['VENDOR', 20674],
['DESCRIPTOR', 'Solid State Logic'],
['MODEL', 112],
['DESCRIPTOR', 'Duende board'],
[ 'NODE_CAPABILITIES',
{ 'addressing': {'64': True, 'fix': True, 'prv': True},
'misc': {'int': False, 'ms': False, 'spt': True},
'state': { 'atn': False,
'ded': False,
'drq': True,
'elo': False,
'init': False,
'lst': True,
'off': False},
'testing': {'bas': False, 'ext': False}}],
[ 'UNIT',
[ ['SPECIFIER_ID', 20674],
['VERSION', 1],
['MODEL', 112],
['DESCRIPTOR', 'Duende board']]]]}
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The > should be >= or otherwise we potentially read one element beyond
the end of the ff->tx_midi_substreams[] array.
Fixes: 73f5537fb209 ("ALSA: fireface: support tx MIDI functionality of Fireface UCX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
