| Age | Commit message (Collapse) | Author |
|---|
|
The cs35l41 supports a low power DSP memory retention mode. Add support
for entering this mode when then device is not in use.
Co-authored-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for the addition of PM runtime support move the test
key out of the register patches themselves. This is necessary to
allow the test key to be held during cache synchronisation, which is
required by the OTP settings which were unpacked from the device and
written by the driver.
Also whilst at it, the driver uses a mixture of accessing the test key
register by name and by address, consistently use the name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It makes no sense to cache the test/user key registers, since they
require values written at specific times, mark them volatile. It is
probably best if they can't be accessed from user-space either, so
mark them precious as well.
The interrupt force, edge, polarity and debounce are all settings
applied to the IRQ rather than status bits and as such should not be
volatile.
The OTP trim values will require re-application in the event of a
cache sync and as such should not be volatile. The OTPID however
should be volatile.
The DSP scratch registers are used to read back an error/debug code
from the DSP on shutdown, as such these should be marked volatile.
Finally, add some missing defaults, add TST_FS_MON0, and allow the
DSP core control register to be cached.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220105113026.18955-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will use the same registers to configure
internal boost for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-7-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will use the same register to set channels
for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA systems require the same errata patches, so
move it to the shared code using a function the correctly
applies the patches by revision
Also, move CS35L41_DSP1_CCM_CORE_CTRL write to errata
patch function as is required to be written at boot,
but not in regmap_register_patch sequence as will affect
waking up from hibernation
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-5-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA systems for all revisions of CS35L41 will benefit
from having this initialization, so add it to reg_sequence of
each revision
By moving to reg_sequence all gains are set to zero. And boost,
monitoring parts, and class D amplifier are disabled.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-4-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will do the same cs35l41_otp_unpack, so move it
to shared code
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-3-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To support CS35L41 in HDA systems the HDA driver
for CS35L41 would have to duplicate some functions
that already exist on ASoC driver
So instead of duplicate the code, use the new lib
source as a shared resource for both ASoC and HDA
Also, change the way CONFIG_SND_SOC_CS35L41 is
selected, as reported by Intel Kernel test robot,
it is possible to build SND_SOC_CS35L41_SPI/I2C
without the main driver, which would lead to build
failures.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
