| Age | Commit message (Collapse) | Author |
|---|
|
The commit d215f63d49da ("ALSA: usb-audio: Check available frames for
the next packet size") introduced the available frame size check, but
the conversion forgot to initialize the temporary variable properly,
and it resulted in a bogus calculation. This patch fixes it.
Fixes: d215f63d49da ("ALSA: usb-audio: Check available frames for the next packet size")
Reported-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211001104417.14291-1-colin.king@canonical.com
Link: https://lore.kernel.org/r/20211001105425.16191-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
While draining a stream, ALSA PCM core stops the stream by issuing
snd_pcm_stop() after all data has been sent out. And, at PCM trigger
stop, currently USB-audio driver kills the in-flight URBs explicitly,
then at sync-stop ops, sync with the finish of all remaining URBs.
This might result in a drop of the drained samples as most of
USB-audio devices / hosts allow relatively long in-flight samples (as
a sort of FIFO).
For avoiding the trimming, this patch changes the stream-stop behavior
during PCM draining state. Under that condition, the pending URBs
won't be killed. The leftover in-flight URBs are caught by the
sync-stop operation that shall be performed after the trigger-stop
operation.
Link: https://lore.kernel.org/r/20210929080844.11583-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is another attempt to improve further the handling of playback
stream in the low latency mode. The latest workaround in commit
4267c5a8f313 ("ALSA: usb-audio: Work around for XRUN with low latency
playback") revealed that submitting URBs forcibly in advance may
trigger XRUN easily. In the classical mode, this problem was avoided
by practically delaying the submission of the actual data with the
pre-submissions of silent data before triggering the stream start.
But that is exactly what we want to avoid.
Now, in this patch, instead of the previous workaround, we take a
similar approach as used in the implicit feedback mode. The URBs are
queued at the PCM trigger start like before, but we check whether the
buffer has been already filled enough before each submission, and
stop queuing if the data overcomes the threshold. The remaining URBs
are kept in the ready list, and they will be retrieved in the URB
complete callback of other (already queued) URBs. In the complete
callback, we try to fill the data and submit as much as possible
again. When there is no more available in-flight URBs that may handle
the pending data, we'll check in PCM ack callback and submit and
process URBs there in addition. In this way, the amount of in-flight
URBs may vary dynamically and flexibly depending on the available data
without hitting XRUN.
The following things are changed to achieve the behavior above:
* The endpoint prepare callback is changed to return an error code;
when there is no enough data available, it may return -EAGAIN.
Currently only prepare_playback_urb() returns the error.
The evaluation of the available data is a bit messy here; we can't
check with snd_pcm_avail() at the point of prepare callback (as
runtime->status->hwptr hasn't been updated yet), hence we manually
estimate the appl_ptr and compare with the internal hwptr_done to
calculate the available frames.
* snd_usb_endpoint_start() doesn't submit full URBs if the prepare
callback returns -EAGAIN, and puts the remaining URBs to the ready
list for the later submission.
* snd_complete_urb() treats the URBs in the low-latency mode similarly
like the implicit feedback mode, and submissions are done in
(now exported) snd_usb_queue_pending_output_urbs().
* snd_usb_queue_pending_output_urbs() again checks the error value
from the prepare callback. If it's -EAGAIN for the normal stream
(i.e. not implicit feedback mode), we push it back to the ready list
again.
* PCM ack callback is introduced for the playback stream, and it calls
snd_usb_queue_pending_output_urbs() if there is no in-flight URB
while the stream is running. This corresponds to the case where the
system needs the appl_ptr update for re-submitting a new URB.
* snd_usb_queue_pending_output_urbs() and the prepare EP callback
receive in_stream_lock argument, which is a bool flag indicating the
call path from PCM ack. It's needed for avoiding the deadlock of
snd_pcm_period_elapsed() calls.
* Set the new SNDRV_PCM_INFO_EXPLICIT_SYNC flag when the new
low-latency mode is deployed. This assures catching each applptr
update even in the mmap mode.
Fixes: 4267c5a8f313 ("ALSA: usb-audio: Work around for XRUN with low latency playback")
Link: https://lore.kernel.org/r/20210929080844.11583-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In theory, stop_urbs() may be called concurrently.
Although we have the state check beforehand, it's safer to apply
ep->lock during the critical list head manipulations.
Link: https://lore.kernel.org/r/20210929080844.11583-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is yet more preparation for the upcoming changes.
Extend snd_usb_endpoint_next_packet_size() to check the available
frames and return -EAGAIN if the next packet size is equal or exceeds
the given size. This will be needed for avoiding XRUN during the low
latency operation.
As of this patch, avail=0 is passed, i.e. the check is skipped and no
behavior change.
Link: https://lore.kernel.org/r/20210929080844.11583-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a preparation patch for the upcoming low-latency improvement
changes.
Rename early_playback_start flag with lowlatency_playback as it's more
intuitive. The new flag is basically a reverse meaning.
Along with the rename, factor out the code to set the flag to a
function. This makes the complex condition checks simpler.
Also, the same flag is introduced to snd_usb_endpoint, too, that is
carried from the snd_usb_substream flag. Currently the endpoint flag
isn't still referred, but will be used in later patches.
Link: https://lore.kernel.org/r/20210929080844.11583-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
USB-audio driver tries to sync with the clear of all pending URBs in
wait_clear_urbs(), and it waits for all bits in active_mask getting
cleared. This works fine for the normal operations, but when a stream
is managed in the implicit feedback mode, there is still a very thin
race window: namely, in snd_complete_usb(), the active_mask bit for
the current URB is once cleared before re-submitted in
queue_pending_output_urbs(). If wait_clear_urbs() is called during
that period, it may pass the test and go forward even though there may
be a still pending URB.
For covering it, this patch adds a new counter to each endpoint to
keep the number of in-flight URBs, and changes wait_clear_urbs()
checking this number instead. The counter is decremented at the end
of URB complete, hence the reference is kept as long as the URB
complete is in process.
Link: https://lore.kernel.org/r/20210929080844.11583-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When a single clock source is shared among several endpoints, we have
to keep the same rate on all active endpoints as long as the clock is
being used. For dealing with such a case, this patch adds one more
check in the hw params constraint for the rate to take the shared
clocks into account. The current rate is evaluated from the endpoint
list that applies the same clock source.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190418
Link: https://lore.kernel.org/r/20210929080844.11583-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The recent change for low latency playback works in most of test cases
but it turned out still to hit errors on some use cases, most notably
with JACK with small buffer sizes. This is because USB-audio driver
fills up and submits full URBs at the beginning, while the URBs would
return immediately and try to fill more -- that can easily trigger
XRUN. It was more or less expected, but in the small buffer size, the
problem became pretty obvious.
Fixing this behavior properly would require the change of the
fundamental driver design, so it's no trivial task, unfortunately.
Instead, here we work around the problem just by switching back to the
old method when the given configuration is too fragile with the low
latency stream handling. As a threshold, we calculate the total
buffer bytes in all plus one URBs, and check whether it's beyond the
PCM buffer bytes. The one extra URB is needed because XRUN happens at
the next submission after the first round.
Fixes: 307cc9baac5c ("ALSA: usb-audio: Reduce latency at playback start, take#2")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210827203311.5987-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent quirk for WALKMAN (commit 7af5a14371c1: "ALSA: usb-audio:
Fix regression on Sony WALKMAN NW-A45 DAC") may be required for other
devices and is worth to be put into the common quirk flags.
This patch adds a new quirk flag bit QUIRK_FLAG_SET_IFACE_FIRST and a
quirk table entry for the device.
Link: https://lore.kernel.org/r/20210824055720.9240-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
We've got a regression report for USB-audio with Sony WALKMAN NW-A45
DAC device where no sound is audible on recent kernel. The bisection
resulted in the code change wrt endpoint management, and the further
debug session revealed that it was caused by the order of the USB
audio interface. In the earlier code, we always set up the USB
interface at first before other setups, but it was changed to be done
at the last for UAC2/3, which is more standard way, while keeping the
old way for UAC1. OTOH, this device seems requiring the setup of the
interface at first just like UAC1.
This patch works around the regression by applying the interface setup
specifically for the WALKMAN at the beginning of the endpoint setup
procedure. This change is written straightforwardly to be easily
backported in old kernels. A further cleanup to move the workaround
into a generic quirk section will follow in a later patch.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214105
Link: https://lore.kernel.org/r/20210824054700.8236-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Yet another delay is applied at switching the interface. This can be
moved to quirk_flags, too.
Link: https://lore.kernel.org/r/20210729073855.19043-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The snd_usb_audio.playback_first flag is used by the implicit feedback
mode handling, and this can be also moved to quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is another quirk for the transfer, and that's currently specific
to Zoom R16/24, handled in create_standard_audio_quirk(). Let's move
this also to the new quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix some spelling mistakes as follows:
altenate ==> alternate
compatbile ==> compatible
perfoms ==> performs
dont'register ==> don't register
periodicaly ==> periodically
arount ==> around
Signed-off-by: gushengxian <gushengxian@yulong.com>
Link: https://lore.kernel.org/r/20210705120052.665212-1-gushengxian507419@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The PCM delay accounting in USB-audio driver is a bit complex to
follow, and this is an attempt to improve the readability and provide
some potential fix.
Basically, the PCM position delay is calculated from two factors: the
in-flight data on URBs and the USB frame counter. For the playback
stream, we advance the hwptr already at submitting URBs. Those
"in-flight" data amount is now tracked, and this is used as the base
value for the PCM delay correction. The in-flight data is decreased
again at URB completion in return. For the capture stream, OTOH,
there is no in-flight data, hence the delay base is zero.
The USB frame counter is used in addition for correcting the current
position. The reference frame counter is updated at each submission
and receiving time, and the difference from the current counter value
is taken into account.
In this patch, each in-flight data bytes is recorded in the new
snd_usb_ctx.queued field, and the total in-flight amount is tracked in
snd_usb_substream.inflight_bytes field, as the replacement of
last_delay field.
Note that updating the hwptr after URB completion doesn't work for
PulseAudio who tries to scratch the buffer on the fly; USB-audio is
basically a double-buffer implementation, hence the scratching the
buffer can't work for the already submitted data. So we always update
hwptr beforehand. It's not ideal, but the delay account should give
enough correctness.
Link: https://lore.kernel.org/r/20210601162457.4877-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent endpoint management change for implicit feedback mode added
a clearance of ep->sync_sink (formerly ep->sync_slave) pointer at
snd_usb_endpoint_stop() to assure no leftover for the feedback from
the already stopped capture stream. This turned out to cause a
regression, however, when full-duplex streams were running and only a
capture was stopped. Because of the above clearance of ep->sync_sink
pointer, no more feedback is done, hence the playback will stall.
This patch fixes the ep->sync_sink clearance to be done only after all
endpoints are released, for addressing the regression.
Reported-and-tested-by: Lucas Endres <jaffa225man@gmail.com>
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426063349.18601-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
During the recent rewrite of the implicit feedback support, we've
tested to apply the implicit fb on BOSS devices, but it failed, as the
capture stream didn't start without the playback. As the end result,
it got another type of quirk for tying both streams but starts
playback always (commit 6234fdc1cede "ALSA: usb-audio: Quirk for BOSS
GT-001").
Meanwhile, Mike Oliphant has tested the real implicit feedback mode
for the playback again with the latest code, and found out that it
actually works if the initial feedback sync is skipped; that is, on
those BOSS devices, the playback stream has to be started at first
without waiting for the capture URB completions. Otherwise it gets
stuck. In the rest operations after the capture stream processed, we
can take them as the implicit feedback source.
This patch is an attempt to improve the support for BOSS devices with
the implicit feedback mode in the way described above. It adds a new
flag to snd_usb_audio, playback_first, indicating that the playback
stream starts without sync with the initial capture completion. This
flag is set in the quirk table with the new IMPLICIT_FB_BOTH type.
Reported-and-tested-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210414083255.9527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the later patch, we're going to issue the PCM sync_stop calls at
disconnection. But currently the USB-audio driver can't handle it
because it has a check of shutdown flag for stopping the URBs. This
is basically superfluous (the stopping URBs are safe at disconnection
state), so let's drop the check.
Fixes: dc5eafe7787c ("ALSA: usb-audio: Support PCM sync_stop")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The endpoint management has bit flags to indicate the current state,
and we're dealing two things: the running bit and the stopping bit.
There is a thin window in transition from the running to the stopping
in stop_urbs(), and as long as the bit flags are used, it's difficult
to plug.
This patch modifies the state management code to use the atomic int
and follow the explicit three states, STOPPED, RUNNING and STOPPING.
The state change is done via atomic_cmpxhg() for avoiding possible
races, and check the state change more strictly. The unexpected state
change is now handled as an error.
Fixes: d0f09d1e4a88 ("ALSA: usb-audio: Refactoring endpoint URB deactivation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we stop an endpoint in release_urbs(), it ignores the
inconsistent endpoint state and tries to release the resources.
This shouldn't happen in theory, but it's still safer to abort the
release and let the caller proper error handling.
Also, stop_and_unlink_urbs() called from release_urbs() does two step
works, and it's more straightforward to split this to two functions
again, so that the call from the PCM trigger won't take the path with
sleeping.
This patch modifies the EP management code to adapt two points above.
Fixes: d0f09d1e4a88 ("ALSA: usb-audio: Refactoring endpoint URB deactivation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The kerndoc comment for the new function snd_usb_endpoint_free_all()
had a typo wrt the argument name. Fix it.
Fixes: 00272c61827e ("ALSA: usb-audio: Avoid unnecessary interface re-setup")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210205082837.6327-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The UAC2/3 sample rate setup is based on the clock node, which is
usually shared in the interface, and can't be re-setup without
deselecting the interface once, and that's how the current code
behaves. OTOH, the sample rate setup of UAC1 is per endpoint, hence
we basically need to call for each endpoint usage even if those share
the same interface.
This patch fixes the behavior of UAC1 to call always
snd_usb_init_sample_rate() in snd_usb_endpoint_configure().
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210118075816.25068-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are devices that have multiple endpoints sharing the same
iface/altset not only for sync but also for the actual streams, and
the audioformat for such an endpoint needs to be handled with the
proper endpoint index; otherwise it confuses the endpoint management.
This patch extends the audioformat to annotate the endpoint index, and
put the proper ep_idx=1 to Pioneer device quirk entries accordingly.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The current endpoint handling assumed (more or less) a unique 1:1
relation between the endpoint and the iface/altset. The exception was
the sync EP without the implicit feedback which has usually the
secondary EP of the same altset. This works fine for most devices,
but it turned out that some unusual devices like Pinoeer's ones have
both playback and capture endpoints in the same iface/altsetting and
use both for the implicit feedback mode. For handling such a case, we
need to extend the endpoint management to take the shared interface
into account.
This patch does that: it adds a new object snd_usb_iface_ref for
managing the reference counts of the each USB interface that is used
by each endpoint. The interface setup is performed only once for the
(sharing) endpoints, and the doubly initialization is avoided.
Along with this, the resource release of endpoints and interface
refcounts are put into a single function, snd_usb_endpoint_free_all()
instead of looping in the caller side.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Just for consistency, use unsigned char for iface and altsetting in
allover places. Also rearrange the field positions of
snd_usb_endpiont and tidy up with some comments.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-35-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Follow the inclusive terminology, just replace sync_master/sync_slave
with sync_source/sync_sink. It's also a bit clearer from its meaning,
too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-34-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are two places calculating the next packet size for the playback
stream in the exactly same way. Provide the single helper for this
purpose and use it from both places gracefully.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-32-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Minor code refactoring to consolidate the URB deactivation code in
endpoint.c. A slight behavior change is that the error handling in
snd_usb_endpoint_start() leaves EP_FLAG_STOPPING now. This should be
synced with the later PCM sync_stop callback.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-30-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The endpoint objects may be started/stopped concurrently by different
substreams in the case of implicit feedback mode, while the current
code handles the reference counter without any protection.
This patch changes the refcount to atomic_t for avoiding the
inconsistency. We need no reference_t here as the refcount goes only
up to 2.
Also the name "use_count" is renamed to "running" since this is about
actually the running status, not the open refcount.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The implicit feedback mode uses a ring buffer for storing the received
packet sizes from the feedback source, and the code has a slight flaw;
when a playback stream stalls by some reason and the URBs aren't
processed, the next_packet FIFO might become empty, but the driver
can't distinguish whether it's empty or full because it's managed with
read_poss and write_pos.
This patch addresses those by changing the next_packet array
management. Instead of keeping read and write positions, now the head
position and the queued amount are kept. It's easier to understand
about the emptiness. Also, the URB active flag is now cleared before
calling queue_pending_output_urbs() for avoiding (theoretically)
possible inconsistency.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is an intensive surgery for the endpoint and stream management
for achieving more robust and clean code.
The goals of this patch are:
- More clear endpoint resource changes
- The interface altsetting control in a single place
Below are brief description of the whole changes.
First off, most of the endpoint operations are moved into endpoint.c,
so that the snd_usb_endpoint object is only referred in other places.
The endpoint object is acquired and released via the new functions
snd_usb_endpoint_open() and snd_usb_endpoint_close() that are called
at PCM hw_params and hw_free callbacks, respectively. Those are
ref-counted and EPs can manage the multiple opens.
The open callback receives the audioformat and hw_params arguments,
and those are used for initializing the EP parameters; especially the
endpoint, interface and altset numbers are read from there, as well as
the PCM parameters like the format, rate and channels. Those are
stored in snd_usb_endpoint object. If it's the secondary open, the
function checks whether the given parameters are compatible with the
already opened EP setup, too.
The coupling with a sync EP (including an implicit feedback sync) is
done by the sole snd_usb_endpoint_set_sync() call.
The configuration of each endpoint is done in a single shot via
snd_usb_endpoint_configure() call. This is the place where most of
PCM configurations are done. A few flags and special handling in the
snd_usb_substream are dropped along with this change.
A significant difference wrt the configuration from the previous code
is the order of USB host interface setups. Now the interface is
always disabled at beginning and (re-)enabled at the last step of
snd_usb_endpoint_configure(), in order to be compliant with the
standard UAC2/3. For UAC1, the interface is set before the parameter
setups since there seem devices that require it (e.g. Yamaha THR10),
just like how it was done in the previous driver code.
The start/stop are almost same as before, also single-shots. The URB
callbacks need to be set via snd_usb_endpoint_set_callback() like the
previous code at the trigger phase, too.
Finally, the flag for the re-setup is set at the device suspend
through the full EP list, instead of PCM trigger. This catches the
overlooked cases where the PCM hasn't been running yet but the device
needs the full setup after resume.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The prepare_data_urb and retire_data_urb fields of the endpoint object
are set dynamically at PCM trigger start/stop. Those are evaluated in
the endpoint handler, but there can be a race, especially if two
different PCM substreams are handling the same endpoint for the
implicit feedback case. Also, the data_subs field of the endpoint is
set and accessed dynamically, too, which has the same risk.
As a slight improvement for the concurrency, this patch introduces the
function to set the callbacks and the data in a shot with the memory
barrier. In the reader side, it's also fetched with the memory
barrier.
There is still a room of race if prepare and retire callbacks are set
during executing the URB completion. But such an inconsistency may
happen only for the implicit fb source, i.e. it's only about the
capture stream. And luckily, the capture stream never sets the
prepare callback, hence the problem doesn't happen practically.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
start_endpoints() may leave the data endpoint running if an error
happens at starting the sync endpoint. We should stop both streams
properly, instead.
While we're at it, move the debug prints into the endpoint.c that is a
more suitable place.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently snd_usb_endpoint objects are created at first when the
substream is opened and tries to assign the endpoints corresponding to
the matching audioformat. But since basically the all endpoints have
been already parsed and the information have been obtained, we may
create the endpoint objects statically at the init phase. It's easier
to manage for the implicit fb case, for example.
This patch changes the endpoint object management and lets the parser
to create the all endpoint objects.
This change shouldn't bring any functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-15-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the current code, there is no check at the stream open time whether
the endpoint is being already used by others. In the normal
operations, this shouldn't happen, but in the case of the implicit
feedback mode, it's a common problem with the full duplex operation,
because the capture stream is always opened by the playback stream as
an implicit sync source.
Although we recently introduced the check of such a conflict of
parameters at the PCM hw_params time, it doesn't give any hint at the
hw_params itself and just gives the error. This isn't quite
comfortable, and it caused problems on many applications.
This patch attempts to make the parameter handling easier by
introducing the strict hw constraint matching with the counterpart
stream that is being used. That said, when an implicit feedback
playback stream is running before a capture stream is opened, the
capture stream carries the PCM hw-constraint to allow only the same
sample rate, format, periods and period frames as the running playback
stream. If not opened or there is no conflict of endpoints, the
behavior remains as same as before.
Note that this kind of "weak link" should work for most cases, but
this is no concrete solution; e.g. if an application changes the hw
params multiple times while another stream is opened, this would lead
to inconsistencies.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are a few rooms for improvements wrt the debug prints:
- The EP debug print is shown only at starting, not at stopping
- The EP debug print contains useless object addresses
- Some helpers show the urb and the EP object addresses, too
This patch addresses those shortcomings.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Factor out the code to obtain snd_usb_endpoint object matching with
the given endpoint. It'll be used in the later patch to add the
implicit feedback hw-constraint.
No functional change by this patch itself.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Drop the duplicated word "there".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Link: https://lore.kernel.org/r/20201005191244.23902-1-rdunlap@infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull uninitialized_var() macro removal from Kees Cook:
"This is long overdue, and has hidden too many bugs over the years. The
series has several "by hand" fixes, and then a trivial treewide
replacement.
- Clean up non-trivial uses of uninitialized_var()
- Update documentation and checkpatch for uninitialized_var() removal
- Treewide removal of uninitialized_var()"
* tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
compiler: Remove uninitialized_var() macro
treewide: Remove uninitialized_var() usage
checkpatch: Remove awareness of uninitialized_var() macro
mm/debug_vm_pgtable: Remove uninitialized_var() usage
f2fs: Eliminate usage of uninitialized_var() macro
media: sur40: Remove uninitialized_var() usage
KVM: PPC: Book3S PR: Remove uninitialized_var() usage
clk: spear: Remove uninitialized_var() usage
clk: st: Remove uninitialized_var() usage
spi: davinci: Remove uninitialized_var() usage
ide: Remove uninitialized_var() usage
rtlwifi: rtl8192cu: Remove uninitialized_var() usage
b43: Remove uninitialized_var() usage
drbd: Remove uninitialized_var() usage
x86/mm/numa: Remove uninitialized_var() usage
docs: deprecated.rst: Add uninitialized_var()
|
|
|
|
usb_free_coherent() is safe with NULL addr and this check is
not required.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200727025208.8739-1-vulab@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Replace several occurences of "frame" with a "packet" where appropriate.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200629025934.154288-2-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit f0bd62b64016 ("ALSA: usb-audio: Improve frames size computation")
introduced a regression for devices which have playback endpoints with
bInterval > 1. Fix this by taking ep->datainterval into account.
Note that frame and fps are actually mean packet and packets per second
in the code introduces by the mentioned commit. This will be fixed in a
follow-up patch.
Fixes: f0bd62b64016 ("ALSA: usb-audio: Improve frames size computation")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208353
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200629025934.154288-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
feedback
For USB sound devices using implicit feedback the endpoint used for
this feedback should be able to be opened twice, once for required
feedback and second time for audio data. This way these devices can be
put in duplex audio mode. Since this only works if the settings of the
endpoint don't change a check is included for this.
This fixes bug 207023 ("MOTU M2 regression on duplex audio") and
should also fix bug 103751 ("M-Audio Fast Track Ultra usb audio device
will not operate full-duplex")
Fixes: c249177944b6 ("ALSA: usb-audio: add implicit fb quirk for MOTU M Series")
Signed-off-by: Erwin Burema <e.burema@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207023
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=103751
Link: https://lore.kernel.org/r/2410739.SCZni40SNb@alpha-wolf
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
