| Age | Commit message (Collapse) | Author |
|---|
|
After one LAG slave is downed and another upped, it takes a while for
the neighbor on a bridge to time out and get renegotiated. The test does
prompt update of FDB entries by arpinging. But because the neighbor
still references another address, offloading is not possible, and some
packets may end up not being mirrored.
To force the neighbor renegotiation, simply flush the neighbor table at
the bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARP or ND traffic can cause spurious migration of FDB back to $swp3.
Mirroring is then updated in accordance with the change, and mirrored
packets are seen at h3, causing a failure.
Detect the case of this spurious roaming, and retry the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The untagged egress test sets up mirroring to {,ip6}gretap such that the
underlay goes through a bridge. Then VLAN flags are manipulated to test
that the traffic leaves the bridge 802.1q-tagged or not, as appropriate.
However, when a neighbor expires at the time that the bridge VLAN is
configured as PVID and egress untagged, the following discovery process
can't finish, because the IP address on H3 is still at the VLAN-tagged
netdevice. This manifests by occasional failures where only several of
the 10 required packets get through.
Therefore, when reconfiguring the VLAN flags, move the IP address to the
appropriate device in the H3 VRF.
In addition to that, take this opportunity to embed an ASCII art diagram
to make the topology move obvious.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in an environment with poor performance (such as a
simulator), processing mirrored packets can take a while. Evaluating the
condition too soon leads to spurious "seen 9, expected 10" failures as
the last packet doesn't have enough time to get mirrored and the mirror
to arrive and bump the observed counters.
Wait for one ping interval before evaluating the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in a simulator, the TTL change takes a while to settle and
during this time the performance of the packet processing is lowered.
The resulting instability leads to ping sending more packets as it
assumes some have been dropped. This then leads to regular spurious
failures as more packets than expected are observed.
Sleep a bit to give the system time to stabilize.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. Those
are mirrored, and over a certain threshold the test case run is
considered a failure, because too much traffic is observed.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change most tests to TLS 1.3, while adding tests for previous TLS 1.2
behavior.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wire up support for 256 bit keys from the setsockopt to the crypto
framework
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This consists of run-time fixes to cpu-hotplug, and seccomp tests,
compile fixes to ir, net, and timers Makefiles"
* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: timers: use LDLIBS instead of LDFLAGS
selftests: net: use LDLIBS instead of LDFLAGS
selftests/seccomp: Enhance per-arch ptrace syscall skip tests
selftests: Use lirc.h from kernel tree, not from system
selftests: cpu-hotplug: fix case where CPUs offline > CPUs present
|
|
|
|
It is easier to distinguish "[ OK ]" from "[FAIL]" than "[PASS]".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reuseport_bpf_numa fails to build due to undefined reference errors:
aarch64-linaro-linux-gcc
--sysroot=/build/tmp-rpb-glibc/sysroots/hikey -Wall
-Wl,--no-as-needed -O2 -g -I../../../../usr/include/ -Wl,-O1
-Wl,--hash-style=gnu -Wl,--as-needed -lnuma reuseport_bpf_numa.c
-o
/build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa
/tmp/ccfUuExT.o: In function `send_from_node':
/build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:138:
undefined reference to `numa_run_on_node'
/tmp/ccfUuExT.o: In function `main':
/build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:230:
undefined reference to `numa_available'
/build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/net/reuseport_bpf_numa.c:233:
undefined reference to `numa_max_node'
It's GNU Make and linker specific.
The default Makefile rule looks like:
$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)
When linking is done by gcc itself, no issue, but when it needs to be passed
to proper ld, only LDLIBS follows and then ld cannot know what libs to link
with.
More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html
LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker,
‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable
instead.
LDLIBS
Library flags or names given to compilers when they are supposed to invoke the
linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to
LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS
variable.
https://lkml.org/lkml/2010/2/10/362
tools/perf: libraries must come after objects
Link order matters, use LDLIBS instead of LDFLAGS to properly link against
libnuma.
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2019-01-25
1) Several patches to fix the fallout from the recent
tree based policy lookup work. From Florian Westphal.
2) Fix VTI for IPCOMP for 'not compressed' IPCOMP packets.
We need an extra IPIP handler to process these packets
correctly. From Su Yanjun.
3) Fix validation of template and selector families for
MODE_ROUTEOPTIMIZATION with ipv4-in-ipv6 packets.
This can lead to a stack-out-of-bounds because
flowi4 struct is treated as flowi6 struct.
Fix from Florian Westphal.
4) Restore the default behaviour of the xfrm set-mark
in the output path. This was changed accidentally
when mark setting was extended to the input path.
From Benedict Wong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds several changes to the ip_defrag selftest, to cover
new IPv6 defrag behavior:
- min IPv6 frag size is now 8 instead of 1280
- new test cases to cover IPv6 defragmentation in nf_conntrack_reasm.c
- new "permissive" mode in negative (overlap) tests: netfilter
sometimes drops invalid packets without passing them to IPv6
underneath, and thus defragmentation sometimes succeeds when
it is expected to fail; so the permissive mode does not fail the
test if the correct reassembled datagram is received instead of a
timeout.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARP suppression allows the Linux bridge to answer ARP requests on behalf
of remote hosts. It reduces the amount of packets a VTEP needs to flood.
This test verifies that ARP suppression on / off works when a neighbour
exists and when it does not exist. It does so by sending an ARP request
from a host connected to one VTEP and checking whether it was received
by a second VTEP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VXLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI. Different tenants
(VRFs) use different L3 VNIs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify that ARP packets are correctly decapsulated by the ingress VTEP
by removing the neighbours configured on both VLAN interfaces and
running a ping test.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In asymmetric routing the ingress VTEP routes the packet into the
correct VXLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.
The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).
While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on flat topology described in file
ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on flat topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a library with helper functions, to be used in testing IP-in-IP and GRE
tunnels, both in flat and in hierarchical topologies.
The topologies used in this library cover the three scenarios of tunnels -
a tunel with no bound device, a tunnel with bound device in the same VRF
and a tunnel with a bound device in a different VRF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test that externally learned FDB entries can roam, but not age out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS test cases recv_partial & recv_peek_large_buf_mult_recs expect to
receive a certain amount of data and then compare it against known
strings using memcmp. To prevent recvmsg() from returning lesser than
expected number of bytes (compared in memcmp), MSG_WAITALL needs to be
passed in recvmsg().
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With very small change to test script we can trigger softlockup due to
bogus assignment of 'p' (policy to be examined) on restart.
Previously the two to-be-merged nodes had same address/prefixlength pair,
so no erase/reinsert was necessary, we only had to append the list from
node a to b.
If prefix lengths are different, the node has to be deleted and re-inserted
into the tree, with the updated prefix length. This was broken; due to
bogus update to 'p' this loops forever.
Add a 'restart' label and use that instead.
While at it, don't perform the unneeded reinserts of the policies that
are already sorted into the 'new' node.
A previous patch in this series made xfrm_policy_inexact_list_reinsert()
use the relative position indicator to sort policies according to age in
case priorities are identical.
Fixes: 6ac098b2a9d30 ("xfrm: policy: add 2nd-level saddr trees for inexact policies")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
... and back to inexact tree.
Repeat ping test after each htresh change: lookup results must not change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The existing script lacks a policy pattern that triggers 'tree node
merges' in the kernel.
Consider adding policy affecting following subnet:
pol1: dst 10.0.0.0/22
pol2: dst 10.0.0.0/23 # adds to existing 10.0.0.0/22 node
-> no problems here. But now, lets consider reverse order:
pol1: dst 10.0.0.0/24
pol2: dst 10.0.0.0/23 # CANNOT add to existing node
When second policy gets added, the kernel must check that the new node
("10.0.0.0/23") doesn't overlap with any existing subnet.
Example:
dst 10.0.0.0/24
dst 10.0.0.1/24
dst 10.0.0.0/23
When the third policy gets added, the kernel must replace the nodes for
the 10.0.0.0/24 and 10.0.0.1/24 policies with a single one and must merge
all the subtrees/lists stored in those nodes into the new node.
The existing test cases only have overlaps with a single node, so no
merging takes place (we can always remove the 'old' node and replace
it with the new subnet prefix).
Add a few 'block policies' in a pattern that triggers this, with a priority
that will make kernel prefer the 'esp' rules.
Make sure the 'tunnel ping' tests still pass after they have been added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Add a VLAN on a bridge port, delete it and make sure the PVID VLAN is
not affected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running the test on the Spectrum ASIC the generated packets are
counted on the ingress filter and injected back to the pipeline because
of the 'pass' action. The router block then drops the packets due to
checksum error, as the test generates packets with zero checksum.
When running the test on an emulator that is not as strict about
checksum errors the test fails since packets are counted twice. Once by
the emulated ASIC on its ingress filter and again by the kernel as the
emulator does not perform checksum validation and allows the packets to
be trapped by a matching host route.
Fix this by changing the action to 'drop', which will prevent the packet
from continuing further in the pipeline to the router block.
For veth pairs this change is essentially a NOP given packets are only
processed once (by the kernel).
Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ade446403bfb ("net: ipv4: do not handle duplicate fragments as
overlapping") changed IPv4 defragmentation so that duplicate fragments,
as well as _some_ fragments completely covered by previously delivered
fragments, do not lead to the whole frag queue being discarded. This
makes the existing ip_defrag selftest flaky.
This patch
* makes sure that negative IPv4 defrag tests generate truly overlapping
fragments that trigger defrag queue drops;
* tests that duplicate IPv4 fragments do not trigger defrag queue drops;
* makes a couple of minor tweaks to the test aimed at increasing its code
coverage and reduce flakiness.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang does not recognize that calls to error() terminate execution
and complains about uninitialized variable use that happens after calls
to error(). This noop patchset fixes this.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without previous patch a warning would be generated upon multipath route
get when FIB multipath hash policy is to use a 5-tuple for multipath
hash calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.
Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors reuseport_add_any selftest a bit:
- makes it more modular (eliminates several copy/pasted blocks);
- skips DCCP tests if DCCP is not supported
V2: added "Signed-off-by" tag.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test to exercise the fix from the previous patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-12-18
1) Add xfrm policy selftest scripts.
From Florian Westphal.
2) Split inexact policies into four different search list
classes and use the rbtree infrastructure to store/lookup
the policies. This is to improve the policy lookup
performance after the flowcache removal.
Patches from Florian Westphal.
3) Various coding style fixes, from Colin Ian King.
4) Fix policy lookup logic after adding the inexact policy
search tree infrastructure. From Florian Westphal.
5) Remove a useless remove BUG_ON from xfrm6_dst_ifdown.
From Li RongQing.
6) Use the correct policy direction for lookups on hash
rebuilding. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tests the below three cases of bridge fdb get:
[bridge, mac, vlan]
[bridge_port, mac, vlan, flags=[NTF_MASTER]]
[vxlandev, mac, flags=NTF_SELF]
depends on iproute2 support for bridge fdb get.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds coverage of DCCP to reuseport_addr_any selftest.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a selftest that verifies that a socket listening
on a specific address is chosen in preference over sockets
that listen on any address. The test covers UDP/UDP6/TCP/TCP6.
It is based on, and similar to, reuseport_dualstack.c selftest.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using VLAN-aware bridges with VXLAN, the VLAN that is mapped to the
VNI of the VXLAN device is that which is configured as "pvid untagged"
on the corresponding bridge port.
When these flags are toggled or when the VLAN is deleted entirely,
remote hosts should not be able to receive packets from the VTEP.
Add a test case for above mentioned scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both msg_zerocopy and udpgso_bench have udp zerocopy variants.
Exercise these as part of the standard kselftest run.
With udp, msg_zerocopy has no control channel. Ensure that the
receiver exits after the sender by accounting for the initial
delay in starting them (in msg_zerocopy.sh).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
