From f7a654933da47929a6bdd1429d563f89ecafcc53 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 21 Jun 2020 14:30:20 +0100 Subject: net: phy: at803x: simplify custom phy id matching The at803x driver contains a function, at803x_match_phy_id(), which tests whether the PHY ID matches the value passed, comparing phy_id with phydev->phy_id and testing all bits that have a "one" in the mask, phydev->drv->phy_id_mask. This is the same test that is used to match the driver, with phy_id replaced with the driver specified ID, phydev->drv->phy_id. Hence, we already know the value of the bits being tested if we look at phydev->drv->phy_id directly, and we do not require a complicated test to check them. Test directly against phydev->drv->phy_id instead. Signed-off-by: Russell King --- drivers/net/phy/at803x.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 32af52dd5aed..9c0f6f947eb9 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -441,12 +441,6 @@ static int at8031_register_regulators(struct phy_device *phydev) return 0; } -static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id) -{ - return (phydev->phy_id & phydev->drv->phy_id_mask) - == (phy_id & phydev->drv->phy_id_mask); -} - static int at803x_parse_dt(struct phy_device *phydev) { struct device_node *node = phydev->mdio.dev.of_node; @@ -511,8 +505,8 @@ static int at803x_parse_dt(struct phy_device *phydev) * to the AR8030 so there might be a good chance it works on * the AR8030 too. */ - if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) || - at803x_match_phy_id(phydev, ATH8035_PHY_ID)) { + if (phydev->drv->phy_id == ATH8030_PHY_ID || + phydev->drv->phy_id == ATH8035_PHY_ID) { priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; } @@ -540,7 +534,7 @@ static int at803x_parse_dt(struct phy_device *phydev) /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping * options. */ - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { if (of_property_read_bool(node, "qca,keep-pll-enabled")) priv->flags |= AT803X_KEEP_PLL_ENABLED; @@ -585,7 +579,7 @@ static int at803x_probe(struct phy_device *phydev) * Switch to the copper page, as otherwise we read * the PHY capabilities from the fiber side. */ - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { phy_lock_mdio_bus(phydev); ret = at803x_write_page(phydev, AT803X_PAGE_COPPER); phy_unlock_mdio_bus(phydev); @@ -701,7 +695,7 @@ static int at803x_config_init(struct phy_device *phydev) if (ret < 0) return ret; - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { + if (phydev->drv->phy_id == ATH8031_PHY_ID) { ret = at8031_pll_config(phydev); if (ret < 0) return ret; -- cgit