From f8a53187a25fdb9fb9b3cbde63f9abdc5c0b7dec Mon Sep 17 00:00:00 2001 From: Stefan Agner Date: Sun, 24 Jun 2018 23:27:24 +0200 Subject: dt-bindings: mtd: add tegra NAND controller binding This adds the devicetree binding for the Tegra 2 NAND flash controller. Signed-off-by: Lucas Stach Signed-off-by: Stefan Agner Reviewed-by: Boris Brezillon Reviewed-by: Rob Herring Signed-off-by: Miquel Raynal --- .../bindings/mtd/nvidia-tegra20-nand.txt | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt (limited to 'Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt') diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt new file mode 100644 index 000000000000..b2f2ca12f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt @@ -0,0 +1,64 @@ +NVIDIA Tegra NAND Flash controller + +Required properties: +- compatible: Must be one of: + - "nvidia,tegra20-nand" +- reg: MMIO address range +- interrupts: interrupt output of the NFC controller +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - nand +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - nand + +Optional children nodes: +Individual NAND chips are children of the NAND controller node. Currently +only one NAND chip supported. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only + "hw" is supported. +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values with "hw" ECC mode are: "rs", "bch". +- nand-bus-width : See nand.txt +- nand-on-flash-bbt: See nand.txt +- nand-ecc-strength: integer representing the number of bits to correct + per ECC step (always 512). Supported strength using HW ECC + modes are: + - RS: 4, 6, 8 + - BCH: 4, 8, 14, 16 +- nand-ecc-maximize: See nand.txt +- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM + are chosen. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +Partitions: see partition.txt + + Example: + nand-controller@70008000 { + compatible = "nvidia,tegra20-nand"; + reg = <0x70008000 0x100>; + interrupts = ; + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>; + clock-names = "nand"; + resets = <&tegra_car 13>; + reset-names = "nand"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <8>; + nand-on-flash-bbt; + nand-ecc-algo = "bch"; + nand-ecc-strength = <8>; + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>; + }; + }; -- cgit